Home › General › MAINTENANCE › ENGINE › from 2020.08
RM27T0E _V1 General _053655 MAINTENANCE _0260400 ENGINE N

MAINTENANCE  ENGINE  GENERAL MAINTENANCE  


CAUTION / NOTICE / HINT

HINT:

Inspect these items on a cooled down engine.


PROCEDURE

Hide 1.REPLACE TIMING BELT

Type See procedure
5L-E (Click here)

Hide 2.INSPECT VALVE CLEARANCE

Type See procedure
5L-E (Click here)

Hide 3.INSPECT DRIVE BELT

Type See procedure
1GR-FE (Click here)
1GD-FTV (Click here)
5L-E (Click here)
2TR-FE (Click here)

Hide 4.REPLACE DRIVE BELT (for 5L-E)

Hide 5.REPLACE SPARK PLUGS

Type See procedure
1GR-FE (Click here)
2TR-FE (Click here)

Hide 6.REPLACE ENGINE OIL AND OIL FILTER

Type See procedure
1GR-FE (Click here)
1GD-FTV (Click here)
5L-E (Click here)
2TR-FE (Click here)

Hide 7.INSPECT COOLING AND HEATER SYSTEM

a.

Check that the radiator, condenser and/or intercooler are not blocked with leaves, dirt or insects, and clean them if necessary. Also check the hose connection for the installation condition, corrosion, etc.


Hide 8.INSPECT ENGINE COOLANT

Type See procedure
1GR-FE (Click here)
1GD-FTV (Click here)
5L-E (Click here)
2TR-FE (Click here)

Hide 9.REPLACE ENGINE COOLANT

Type See procedure
1GR-FE (Click here)
1GD-FTV (Click here)
5L-E (Click here)
2TR-FE (Click here)

Hide 10.INSPECT OIL COOLER HOSE AND CONNECTIONS (for 1GR-FE, 2TR-FE)

a.

Check the oil cooler hoses (water by-pass hose) for cracks, leakage, loose connections and deformation.


Hide 11.INSPECT VACUUM PUMP OIL HOSE (for 5L-E)

a.

Check the vacuum pump oil hoses for cracks, leakage, loose connections and deformation.


Hide 12.INSPECT EXHAUST PIPES AND MOUNTINGS

a.

Visually check the pipes, hangers and connections for severe corrosion, leaks or damage.


Hide 17801 13.INSPECT AIR CLEANER FILTER

a.

Remove the air cleaner filter.


b.

Visually check that the air cleaner filter is not excessively damaged or oily.


c.

Replace the air cleaner filter with a new one if necessary.


Hide 14.INSPECT AIR CLEANER CASE

a.

Check if foreign matter has accumulated in the bottom of the air cleaner case. If foreign matter has accumulated in the bottom of the air cleaner case, clean the air cleaner case.

NOTICE:

When cleaning the air cleaner case, prevent any foreign matter from entering into the engine.



Hide 15.INSPECT AIR FLOW METER (for 1GD-FTV)

a.

Blow air to the sensor intermittently for approximately 30 seconds.


Hide 16.INSPECT FUEL TANK CAP GASKET

Type See procedure
1GR-FE (Click here)
1GD-FTV (Click here)
5L-E (Click here)
2TR-FE (Click here)

Hide 17.INSPECT FUEL LINES, FUEL LINE CONNECTIONS, FUEL TANK VAPOR VENT SYSTEM HOSES AND FUEL TANK BAND

a.

Visually check the fuel lines and hoses for cracks, leakage, loose connections and deformation. Also, visually check the tank band for looseness.


Hide 18.INSPECT BATTERY ELECTROLYTE LEVEL

Type See procedure
1GR-FE (Click here)
1GD-FTV (Click here)
5L-E (Click here)
2TR-FE (Click here)

Hide 19.REPLACE FUEL FILTER

Type See procedure
1GR-FE (Click here)
1GD-FTV (Click here)
1GD-FTV (for Cylinder Block Side) (Click here)
1GD-FTV (for Fuel Tank Side) (Click here)
5L-E (Click here)
2TR-FE (Click here)

Hide 20.REPLACE FUEL PUMP (for Dual Fuel Tank)

Type See procedure
1GD-FTV (Click here)

Hide 21.INSPECT WATER SEDIMENT ACCUMULATOR

Type See procedure
1GD-FTV (Click here)
5L-E (Click here)

Hide 22.INSPECT CHARCOAL CANISTER

Type See procedure
1GR-FE (Click here)
2TR-FE (Click here)