The combination meter assembly detects whether either rear door is open or closed based on the condition of the left and right courtesy light switches. The combination meter assembly detects the rear seat belt state. The rear seat belt warning lights on the combination meter assembly illuminate or turn off in accordance with the rear door state, vehicle speed and rear seat belt state.
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| RR Door Courtesy SW | Rear door courtesy light switch RH / ON or OFF | ON: Rear door RH open
OFF: Rear door RH closed |
- |
| RL Door Courtesy SW | Rear door courtesy light switch LH / ON or OFF | ON: Rear door LH open
OFF: Rear door LH closed |
- |
| Tester Display |
|---|
| RR Door Courtesy SW |
| RL Door Courtesy SW |
The GTS display changes correctly in response to the rear door condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM (except 5L-E)>Door Courtesy Switch Circuit
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Normal Condition | Diagnostic Note |
|---|---|---|---|
| 2nd-Row Seatbelt Buckle (R) | Rear No. 1 RH seat belt buckle switch signal / ON or OFF | ON: Rear No. 1 RH seat belt not fastened
OFF: Rear No. 1 RH seat belt fastened |
- |
| 2nd-Row Seatbelt Buckle (L) | Rear No. 1 LH seat belt buckle switch signal / ON or OFF | ON: Rear No. 1 LH seat belt not fastened
OFF: Rear No. 1 LH seat belt fastened |
- |
| 2nd-Row Seatbelt Buckle (C) | Rear No. 1 center seat belt buckle switch signal / ON or OFF | ON: Rear No. 1 center seat belt not fastened
OFF: Rear No. 1 center seat belt fastened |
- |
| 3rd-Row Seatbelt Buckle (R) | Rear No. 2 RH seatbelt buckle switch signal / ON or OFF | ON: Rear No. 2 RH seat belt not fastened
OFF: Rear No. 2 RH seat belt fastened |
w/ Rear No. 2 Seat Belt Warning |
| 3rd-Row Seatbelt Buckle (L) | Rear No. 2 LH seatbelt buckle switch signal / ON or OFF | ON: Rear No. 2 LH seat belt not fastened
OFF: Rear No. 2 LH seat belt fastened |
w/ Rear No. 2 Seat Belt Warning |
| Tester Display |
|---|
| 2nd-Row Seatbelt Buckle (R) |
| 2nd-Row Seatbelt Buckle (L) |
| 2nd-Row Seatbelt Buckle (C) |
| 3rd-Row Seatbelt Buckle (R) |
| 3rd-Row Seatbelt Buckle (L) |
The GTS display changes correctly in response to the rear seat belt buckle condition.
| Result | Proceed to |
|---|---|
| ON or OFF is displayed on the GTS screen according to the rear seat belt condition | A |
| ON or OFF is not displayed normally on the GTS screen according to the rear LH seat belt condition | B |
| ON or OFF is not displayed normally on the GTS screen according to the rear center seat belt condition | C |
| ON or OFF is not displayed normally on the GTS screen according to the rear RH seat belt condition | D |
| ON or OFF is not displayed normally on the GTS screen according to the rear No. 2 LH seat belt condition (w/ Rear No. 2 Seat Belt Warning) | E |
| ON or OFF is not displayed normally on the GTS screen according to the rear No. 2 RH seat belt condition (w/ Rear No. 2 Seat Belt Warning | F |
A
B
C
D
E
F
Check vehicle condition.
| Result | Proceed to |
|---|---|
| for 60/40 Split Slide Walk-in Seat Type | A |
| for 60/40 Split Double-folding Seat Type | B |
| for 60/40 Split Tumble Seat Type | C |
A
B
C
Remove the rear No. 1 seat inner belt assembly LH.
Inspect the rear No. 1 seat inner belt assembly LH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the x3 rear No. 1 seat inner belt assembly LH connector.
Disconnect the G304 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| x3-3 (LBR+) - G304-36 (RLSB) | Always | Below 1 Ω |
| x3-2 (LBR-) - Body ground | Always | Below 1 Ω |
| x3-3 (LBR+) or G304-36 (RLSB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear No. 1 seat inner belt assembly LH.
Inspect the rear No. 1 seat inner belt assembly LH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the u1 rear No. 1 seat inner belt assembly LH connector.
Disconnect the G304 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| u1-4 (LBR+) - G304-36 (RLSB) | Always | Below 1 Ω |
| u1-5 (LBR-) - Body ground | Always | Below 1 Ω |
| u1-4 (LBR+) or G304-36 (RLSB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear seat inner belt assembly center.
Inspect the rear seat inner belt assembly center.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear No. 1 seat inner belt assembly LH.
Inspect the rear No. 1 seat inner belt assembly LH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the R52 rear seat inner belt assembly center connector.
Disconnect the G304 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R52-4 (LBR+) - G304-36 (RLSB) | Always | Below 1 Ω |
| R52-5 (LBR-) - Body ground | Always | Below 1 Ω |
| R52-4 (LBR+) or G304-36 (RLSB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check vehicle condition.
| Result | Proceed to |
|---|---|
| for 60/40 Split Slide Walk-in Seat Type | A |
| for 60/40 Split Double-folding Seat Type | B |
| for 60/40 Split Tumble Seat Type | C |
A
B
C
Remove the rear seat inner belt assembly center.
Inspect the rear seat inner belt assembly center.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the w5*1, x4*2 rear seat inner belt assembly center connector.
*1: for LHD
*2: for RHD
Disconnect the G304 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| w5-3 (CBR+) - G304-28 (RCSB) | Always | Below 1 Ω |
| w5-2 (CBR-) - Body ground | Always | Below 1 Ω |
| w5-3 (CBR+) or G304-28 (RCSB) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| x4-3 (CBR+) - G304-28 (RCSB) | Always | Below 1 Ω |
| x4-2 (CBR-) - Body ground | Always | Below 1 Ω |
| x4-3 (CBR+) or G304-28 (RCSB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear seat inner belt assembly center.
Inspect the rear seat inner belt assembly center.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear No. 1 seat inner belt assembly RH.
Inspect the rear No. 1 seat inner belt assembly RH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the t2 rear No. 1 seat inner belt assembly RH connector.
Disconnect the G304 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| t2-1 (CBR+) - G304-28 (RCSB) | Always | Below 1 Ω |
| t2-2 (CBR-) - Body ground | Always | Below 1 Ω |
| t2-1 (CBR+) or G304-28 (RCSB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear seat inner belt assembly center.
Inspect the rear seat inner belt assembly center.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the R52 rear seat inner belt assembly center connector.
Disconnect the G304 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R52-1 (CBR+) - G304-28 (RCSB) | Always | Below 1 Ω |
| R52-2 (CBR-) - Body ground | Always | Below 1 Ω |
| R52-1 (CBR+) or G304-28 (RCSB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check vehicle condition.
| Result | Proceed to |
|---|---|
| for 60/40 Split Slide Walk-in Seat Type | A |
| for 60/40 Split Double-folding Seat Type | B |
| for 60/40 Split Tumble Seat Type | C |
A
B
C
Remove the rear No. 1 seat inner belt assembly RH.
Inspect the rear No. 1 seat inner belt assembly RH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the w4 rear No. 1 seat inner belt assembly RH connector.
Disconnect the G304 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| w4-3 (RBR+) - G304-23 (RRSB) | Always | Below 1 Ω |
| w4-2 (RBR-) - Body ground | Always | Below 1 Ω |
| w4-3 (RBR+) or G304-23 (RRSB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear No. 1 seat inner belt assembly RH.
Inspect the rear No. 1 seat inner belt assembly RH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the t2 rear No. 1 seat inner belt assembly RH connector.
Disconnect the G304 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| t2-4 (RBR+) - G304-23 (RRSB) | Always | Below 1 Ω |
| t2-5 (RBR-) - Body ground | Always | Below 1 Ω |
| t2-4 (RBR+) or G304-23 (RRSB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear No. 1 seat inner belt assembly RH.
Inspect the rear No. 1 seat inner belt assembly RH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Q46 rear No. 1 seat inner belt assembly RH connector.
Disconnect the G304 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q46-4 (RBR+) - G304-23 (RRSB) | Always | Below 1 Ω |
| Q46-5 (RBR-) - Body ground | Always | Below 1 Ω |
| Q46-4 (RBR+) or G304-23 (RRSB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear No. 2 seat inner belt assembly LH.
for Manual Seat:
Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT INNER BELT ASSEMBLY (for Manual Seat)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT INNER BELT ASSEMBLY (for Power Seat)>REMOVAL
Inspect the rear No. 2 seat inner belt assembly LH.
for Manual Seat:
Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT INNER BELT ASSEMBLY (for Manual Seat)>INSPECTION
for Power Seat:
Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT INNER BELT ASSEMBLY (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Manual Seat:
Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT INNER BELT ASSEMBLY (for Manual Seat)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT INNER BELT ASSEMBLY (for Power Seat)>REMOVAL
Disconnect the d8 rear No. 2 seat inner belt assembly LH connector.
Disconnect the G304 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| d8-1 - G304-19 (RLBT) | Always | Below 1 Ω |
| d8-2 - Body ground | Always | Below 1 Ω |
| d8-1 or G304-19 (RLBT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear No. 2 seat inner belt assembly RH.
for Manual Seat:
Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT INNER BELT ASSEMBLY (for Manual Seat)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT INNER BELT ASSEMBLY (for Power Seat)>REMOVAL
Inspect the rear No. 2 seat inner belt assembly RH.
for Manual Seat:
Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT INNER BELT ASSEMBLY (for Manual Seat)>INSPECTION
for Power Seat:
Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT INNER BELT ASSEMBLY (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Manual Seat:
Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT INNER BELT ASSEMBLY (for Manual Seat)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT INNER BELT ASSEMBLY (for Power Seat)>REMOVAL
Disconnect the c5 rear No. 2 seat inner belt assembly RH connector.
Disconnect the G304 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| c5-1 - G304-4 (RRBT) | Always | Below 1 Ω |
| c5-2 - Body ground | Always | Below 1 Ω |
| c5-1 or G304-4 (RRBT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG