1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
2.DISCHARGE FUEL SYSTEM PRESSURE
3. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
53301
5.REMOVE HOOD SUB-ASSEMBLY
Remove the 2 hood support bolts and disconnect the hood supports.
Remove the 4 bolts and hood.
55781E
6.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
53806
7.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
53805
8.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
51405A
9.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
51442
10.REMOVE NO. 2 ENGINE UNDER COVER
Remove the 2 bolts and No. 2 engine under cover.
53292A
11.REMOVE UPPER RADIATOR SUPPORT SEAL
53111
12.REMOVE RADIATOR GRILLE
52119A
13.REMOVE FRONT BUMPER COVER
for Standard (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(for Standard)>REMOVAL)
w/ Winch (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(w/ Winch)>REMOVAL)
14.DRAIN ENGINE COOLANT
11259
15.REMOVE V-BANK COVER
32917
16.REMOVE TRANSMISSION OIL COOLER AIR DUCT (w/ Air Cooled Transmission Oil Cooler)
53293C
17.REMOVE RADIATOR SIDE DEFLECTOR RH (w/o Air Cooled Transmission Oil Cooler)
53294C
18.REMOVE RADIATOR SIDE DEFLECTOR LH
16571C
19.REMOVE NO. 1 RADIATOR HOSE
16572D
20.REMOVE NO. 2 RADIATOR HOSE
32907A
21.DISCONNECT OIL COOLER TUBE (w/ Air Cooled Transmission Oil Cooler)
16711
22.REMOVE FAN SHROUD
32921D
23.DISCONNECT INLET OIL COOLER HOSE
32922A
24.DISCONNECT OUTLET OIL COOLER HOSE
16400
25.REMOVE RADIATOR ASSEMBLY
26.DRAIN ENGINE OIL
27.REMOVE AIR CLEANER CAP AND HOSE
Remove the air cleaner cap and hose.
Disconnect the mass air flow meter connector, vacuum hose and ventilation hose and detach the clamp.
Loosen the clamp.
Unfasten the 4 hook clamps, and then remove the bolt and the air cleaner cap and hose.
28.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
Remove the air cleaner filter element.
Remove the 3 bolts and air cleaner case.
29.REMOVE AIR TUBE ASSEMBLY (w/ Secondary Air Injection System)
17129
30.REMOVE INTAKE AIR SURGE TANK
82121
31.DISCONNECT ENGINE WIRE
Remove the junction block cover.
Disconnect the ECM connector (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL).
Detach the wire harness clamp.
Disconnect the 4 connectors from the junction block.
Remove the engine room relay block cover.
Remove the bolt and disconnect the ground wire from the bracket.
w/ Secondary Air Injection System:
Disconnect the 2 air injection control driver connectors and detach the clamp.
Disconnect the 2 connectors and 2 clips from the engine room junction block.
Remove the nut and disconnect the wire and 2 clips from the engine room junction block.
Remove the nut and disconnect the wire from the positive (+) battery cable.
Disconnect the cable from the positive (+) battery terminal.
Remove the bolt and detach the wire harness clamp, and then disconnect the ground wire from the body.
Disconnect the connector and detach the 2 clamps.
w/ Winch:
Remove the 2 bolts and winch ground wire.
Disconnect the power steering switch connector and detach the clamp.
w/ Secondary Air Injection System:
Disconnect the air pump connector and detach the clamp.
89465
32.REMOVE HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)
17430
33.REMOVE TAILPIPE ASSEMBLY
17420
34.REMOVE CENTER EXHAUST PIPE ASSEMBLY
17450B
35.REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY
89465
36.REMOVE HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)
17410
37.REMOVE FRONT EXHAUST PIPE ASSEMBLY
53782
38.REMOVE FRONT FENDER APRON TRIM PACKING A
53783
39.REMOVE FRONT FENDER APRON TRIM PACKING B
53784
40.REMOVE FRONT FENDER APRON TRIM PACKING C
53785B
41.REMOVE FRONT FENDER APRON TRIM PACKING D
17118
42.REMOVE MANIFOLD STAY
17361
43.REMOVE AIR TUBE (w/ Secondary Air Injection System)
45203A
44.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT
17167
45.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
17104
46.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH
17119
47.REMOVE NO. 2 MANIFOLD STAY
17362
48.REMOVE NO. 2 AIR TUBE (w/ Secondary Air Injection System)
17168
49.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
17105
50.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH
87209
51.DISCONNECT WATER HOSE SUB-ASSEMBLY
Disconnect the water hoses.
| *A | w/o Rear Heater |
| *B | w/ Rear Heater |
44320
52.DISCONNECT VANE PUMP ASSEMBLY
27020
53.REMOVE GENERATOR ASSEMBLY
88711
54.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
88704
55.DISCONNECT SUCTION HOSE SUB-ASSEMBLY
88320
56.REMOVE COOLER COMPRESSOR ASSEMBLY
23801P
57.DISCONNECT NO. 1 AND NO. 2 FUEL PIPES
Disconnect the No. 1 and No. 2 fuel pipes (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).
35000
58.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
12371
59.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR
Only perform this procedure when replacement of the engine mounting insulator is necessary.
Remove the 4 bolts and rear engine mounting insulator from the transmission.
32907C
60.DISCONNECT NO. 1 OIL COOLER HOSE TUBE SUB-ASSEMBLY
Remove the 2 bolts and cooler hose tube.
32101
61.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY
Using SST, hold the crankshaft.
Remove the 8 bolts, rear spacer, drive plate and front spacer.
Do not reuse the bolts.
62.INSTALL ENGINE HANGER
Install 2 engine hangers with 4 bolts as shown in the illustration.
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
| No. 1 Engine Hanger | 12281-31110 |
| No. 2 Engine Hanger | 12282-31140 |
| Bolt | 91671-C0830 |
63.REMOVE ENGINE ASSEMBLY
Attach an engine sling device and hang the engine with a chain block.
Remove the 2 nuts and 4 bolts from the front engine mounting insulator LH and RH.
Lift the engine out of the vehicle carefully.
Make sure the engine is clear of all wiring and hoses.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
Remove the front engine mounting insulator LH and RH.
Place the engine onto a work bench.
64.INSTALL ENGINE STAND
Install the engine onto an engine stand with bolts.
Remove the 4 bolts and 2 engine hangers.
12316A
65.REMOVE FRONT NO. 2 ENGINE MOUNTING BRACKET LH
Remove the bolt and front No. 2 engine mounting bracket LH.