for V35A-FTS:
By using the starter delay circuit, the engine stop and start ECU can activate the ST NO. 2 relay (for starter motor operation) after activating the ST NO. 1 relay (for starter pinion operation) to operate the starter assembly.
for F33A-FTV:
The engine stop and start ECU can activates the ST NO. 1 relay to operation the starter assembly.
Before replacing the engine stop and start ECU, read the number of starter operations, total number of engine starts and write it into a new engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
After replacing the starter assembly, perform initialization of the number of starter operations stored in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
After replacing the engine stop and start ECU assembly, perform learning of the external backup boost converter (eco run vehicle converter assembly).
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
for V35A-FTS:
When the starter assembly is replaced, "ST NO. 1 relay" and "ST NO. 2 relay" must be also replaced.
for F33A-FTV:
When the starter assembly is replaced, "ST NO. 1 relay" must be also replaced.
Inspect the fuses for circuits related to this system before performing the following procedure.
When disconnecting and reconnecting the battery.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Turn the ignition switch START and check that the engine cranks.
| Result | Proceed to |
|---|---|
| Engine cranks | A |
| Engine does not crank | B |
A
B
Enter the following menus: Powertrain / Stop and Start / Active Test / Starter(Hood Close).
| Tester Display |
|---|
| Starter(Hood Close) |
Check whether the engine cranks while the Active Test "Starter" is being performed.
The Active Test "Starter" is stopped automatically 3 seconds after the starter assembly begins operating.
Engine cranks
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Check the vehicle control history (RoB).
| Result | Proceed to |
|---|---|
| Engine control system Vehicle Control History (RoB) is not output | A |
| Engine Difficult to Start is output | B |
| Result other than Engine Difficult to Start is output | C |
If the value of "Cranking Time" is approximately 1.5 seconds, the stop and start control system or starter system may be malfunctioning.
If the value of "Cranking Time" is small (approximately 0.5 seconds or less: the minimum value varies depending on the model), the engine control system may be malfunctioning.
The Data List item "Cranking Time" indicates the length of time starter operation is requested by the engine stop and start ECU. If the engine speed exceeds the specified value, the engine stop and start ECU cancels its start request.
A
B
C
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>VEHICLE CONTROL HISTORY (RoB)
for F33A-FTV:
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>VEHICLE CONTROL HISTORY (RoB)
Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Select Engine Difficult to Start from the Vehicle Control History to display the data from the time of control.
Check the output data.
Checking the freeze frame data allows the vehicle conditions at the time of detection to be confirmed.
As Vehicle Control History may be overwritten whenever the trigger conditions are met, make sure to save the Vehicle Control History data before performing any inspections.
| Result | Proceed to |
|---|---|
| Engine speed does not rise to approximately 300 rpm (Starter does not rotate) | A |
| Engine speed rises to approximately 300 rpm (Starter rotates) | B |
A
B
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>VEHICLE CONTROL HISTORY (RoB)
for F33A-FTV:
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>VEHICLE CONTROL HISTORY (RoB)
Enter the following menus: Powertrain / Stop and Start / Utility / Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Select a vehicle control history item to display the data from the time of control.
Check the output data.
| Tester Display | Result | Proceed to |
|---|---|---|
| Engine Stall History during Stop&Start (Collision or Battery Voltage Low) | Yes | A |
| Engine Stall History during Engine Starting (Collision) | Yes | |
| Engine Start Fail | Yes | B |
| Vehicle control history item is not output or No is displayed for the results of all of the freeze frame data above | ||
A
B
Check if the vehicle was in a collision when the engine stalled.
| Result | Proceed to |
|---|---|
| Vehicle was in collision when engine stalled | A |
| Vehicle was not in collision when engine stalled | B |
When "Engine Stall History during Stop&Start (Collision or Battery Voltage Low)" or "Engine Stall History during Engine Starting (Collision)" is stored:
This may have been stored because the vehicle was in a collision or a collision detection signal was input while stop and start control was operating.
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
| Result | Proceed to |
|---|---|
| for V35A-FTS | A |
| for F33A-FTV | B |
A
B
Disconnect the engine stop and start ECU connector.
Remove the ST NO. 1 and ST NO. 2 relays from the NO. 2 engine room relay block and junction block assembly.
Disconnect the certification ECU (smart key ECU assembly) connector.
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B38)Location & Routingewd_type=routing;type=c;code=B38 Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECUewd_type=component;type=c;code=B38;pinno=21,23 |
||
| B38-21 (STA) - ST NO. 1 relay terminal 2 | Always | Below 1 Ω |
| B38-23 (STA2) - ST NO. 2 relay terminal 2 | Always | Below 1 Ω |
| B38-21 (STA) - Body ground | Always | 10 kΩ or higher |
| ST NO. 1 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| B38-23 (STA2) - Body ground | Always | 10 kΩ or higher |
| ST NO. 2 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 and ST NO. 2 relays from the NO. 2 engine room relay block and junction block assembly
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay terminal 1 - Body ground | Always | Below 1 Ω |
| ST NO. 2 relay terminal 1 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 and ST NO. 2 relays from the NO. 2 engine room relay block and junction block assembly
| *1 | NO. 2 Engine Room Relay Block and Junction Block Assembly |
| *a | ST NO. 1 Relay Terminal |
| *b | ST NO. 2 Relay Terminal |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay terminal 5 - Body ground | Always | 9.5 to 14 V |
| ST NO. 2 relay terminal 5 - Body ground | Always | 9.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Starter Assembly |
| *a | C56-1 (B) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C56)Location & Routingewd_type=routing;type=c;code=C56 |
||
| C56-1 (B) - Body ground | Always | 9.5 to 14 V |
Before performing this step, check that the starter assembly connector C56 is not disconnected or loose.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 and ST NO. 2 relays from the NO. 2 engine room relay block and junction block assembly.
Disconnect the starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C52)Location & Routingewd_type=routing;type=c;code=C52 |
||
| ST NO. 1 relay terminal 3 - C52-2 (ST) | Always | Below 1 Ω |
| ST NO. 2 relay terminal 3 - C52-1 (SL2) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ST NO. 1 relay.
Click hereEngine / Hybrid System>V35A-FTS (STARTING)>RELAY>ON-VEHICLE INSPECTION
Inspect the ST NO. 2 relay.
Click hereEngine / Hybrid System>V35A-FTS (STARTING)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the starter assembly.
Click hereEngine / Hybrid System>V35A-FTS (STARTING)>STARTER (w/ Stop And Start System)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL
If arriving at this item from the item "Drive command is being sent from the engine stop and start ECU but the starter itself is not moving" of "After Engine Stops due to Stop and Start System, Engine does not Restart" in Stop and Start / Stop and Start System / Problem Symptoms Table, go to SIMULATION METHOD.
NG
Disconnect the engine stop and start ECU connector.
Remove the ST NO. 1 relays from the NO. 4 engine room relay block and junction block assembly.
Disconnect the certification ECU (smart key ECU assembly) connector.
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B38)Location & Routingewd_type=routing;type=c;code=B38 |
||
| B38-21 (STA) - ST NO. 1 relay terminal 2 | Always | Below 1 Ω |
| B38-21 (STA) - Body ground | Always | 10 kΩ or higher |
| ST NO. 1 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relays from the NO. 4 engine room relay block and junction block assembly
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay terminal 1 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relays from the NO. 4 engine room relay block and junction block assembly
| *1 | NO. 4 Engine Room Relay Block and Junction Block Assembly |
| *a | ST NO. 1 Relay Terminal |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay terminal 5 - Body ground | Always | 9.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Starter Assembly |
| *a | C180-1 (B) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C180)Location & Routingewd_type=routing;type=c;code=C180 |
||
| C180-1 (B) - Body ground | Always | 9.5 to 14 V |
Before performing this step, check that the starter assembly connector C180 is not disconnected or loose.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relays from the NO. 4 engine room relay block and junction block assembly.
Disconnect the starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C181,C182)Location & Routingewd_type=routing;type=c,c;code=C181,C182 |
||
| ST NO. 1 relay terminal 3 - C181-1 (ST) | Always | Below 1 Ω |
| ST NO. 1 relay terminal 3 - C182-1 (ZYV) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ST NO. 1 relay.
Click hereEngine / Hybrid System>F33A-FTV (STARTING)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the starter assembly.
Click hereEngine / Hybrid System>F33A-FTV (STARTING)>STARTER (w/ Stop And Start System)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL
If arriving at this item from the item "Drive command is being sent from the engine stop and start ECU but the starter itself is not moving" of "After Engine Stops due to Stop and Start System, Engine does not Restart" in Stop and Start / Stop and Start System / Problem Symptoms Table, go to SIMULATION METHOD.
NG
Disconnect the engine stop and start ECU connectors.
| *a | Front view of wire harness connector (to Engine Stop and Start ECU) |
- | - |
Measure the voltage according to the value(s) in the table below.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B38)Location & Routingewd_type=routing;type=c;code=B38 Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECUewd_type=component;type=c;code=B38;pinno=21,6 |
||
| B38-21 (STA) - B38-6 (DGND) | Cranking commanded via Active Test item Starter(Hood Close) | 6 to 14 V |
The Active Test "Starter" is stopped automatically 3 seconds after the starter assembly begins operating.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL
If arriving at this item from the item "Drive command is being sent from the engine stop and start ECU but the starter itself is not moving" of "After Engine Stops due to Stop and Start System, Engine does not Restart" in Stop and Start / Stop and Start System / Problem Symptoms Table, go to SIMULATION METHOD.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Stop and Start / Active Test / Starter(Hood Close).
| Tester Display |
|---|
| Starter(Hood Close) |
Check whether the engine cranks while the Active Test "Starter" is being performed.
The Active Test "Starter" is stopped automatically 3 seconds after the starter assembly begins operating.
Engine cranks
| Result | Proceed to |
|---|---|
| Engine cranks | A |
| Engine does not crank (for V35A-FTS) |
B |
| Engine does not crank (for F33A-FTV) |
C |
A
B
C
Enter the following menus: Powertrain / Stop and Start / Data List / Neutral Switch.
| Tester Display |
|---|
| Neutral Switch |
In accordance with the display on the GTS, read the Data List.
| Tester Display | Condition | Normal Condition |
|---|---|---|
| Neutral Switch | Shift lever in P or N | ON |
| Shift lever not in P or N | OFF |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the park/neutral position switch assembly connector.
Disconnect the certification ECU (smart key ECU assembly) connector.
Disconnect the engine stop and start ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I40,B38,C34)Location & Routingewd_type=routing;type=c,c,c;code=I40,B38,C34 Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECUewd_type=component;type=c;code=B38;pinno=17 |
||
| I40-10 (STAR) - B38-17 (CLL) | Always | Below 1 Ω |
| I40-10 (STAR) - C34-4 (B) | Always | Below 1 Ω |
| I40-10 (STAR) - Body ground | Always | 10 kΩ or higher |
| B38-17 (CLL) - Body ground | Always | 10 kΩ or higher |
| C34-4 (B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the engine stop and start ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B38)Location & Routingewd_type=routing;type=c;code=B38 Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECUewd_type=component;type=c;code=B38;pinno=17 |
||
| B38-17 (CLL) - Body ground | Engine started using ignition switch (ignition switch turned to START) | 9.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Inspect the park/neutral position switch assembly.
Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL
Disconnect the certification ECU (smart key ECU assembly) connector.
for V35A-FTS:
Remove the ST NO. 1 relay from the NO. 2 engine room relay block and junction block assembly.
for F33A-FTV:
Remove the ST NO. 1 relay from the NO. 4 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I40)Location & Routingewd_type=routing;type=c;code=I40 |
||
| I40-10 (STAR) - ST NO. 1 relay terminal 2 | Shift lever in P or N | Below 1 Ω |
| Shift lever not in P or N | 10 kΩ or higher | |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL
If arriving at this item from the item "Drive command is being sent from the engine stop and start ECU but the starter itself is not moving" of "After Engine Stops due to Stop and Start System, Engine does not Restart" in Stop and Start / Stop and Start System / Problem Symptoms Table, go to SIMULATION METHOD.
NG
Connect an oscilloscope to the STA, STA2 and DGND terminals of the engine stop and start ECU connector.
| *a | Component with harness connected (Engine Stop and Start ECU) |
- | - |
Check the waveform immediately after turning the ignition switch to START.
| Item | Condition |
|---|---|
| Tester Connection | B38-21 (STA) - B38-6 (DGND) B38-23 (STA2) - B38-6 (DGND) |
| Condition | Engine started by ignition switch operation |
| Result | Proceed to |
|---|---|
| Delay between ST NO. 1 relay turning on and ST NO. 2 relay turning on: between 0.03 and 0.06 seconds | A |
| Delay between ST NO. 1 relay turning on and ST NO. 2 relay turning on: not between 0.03 and 0.06 seconds | B |
| ST NO. 1 relay turns on and ST NO. 2 relay does not turn on | C |
| ST NO. 1 relay and ST NO. 2 relay do not turn on | D |
After replacing the engine stop and start ECU, make sure that the drive plate and ring gear sub-assembly and starter pinion gear are not excessively worn. A malfunction in the delay circuit may cause the drive plate and ring gear sub-assembly or starter pinion gear to be worn or damaged.
A
B
Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL
If arriving at this item from the item "Drive command is being sent from the engine stop and start ECU but the starter itself is not moving" of "After Engine Stops due to Stop and Start System, Engine does not Restart" in Stop and Start / Stop and Start System / Problem Symptoms Table, go to SIMULATION METHOD.
C
D
Inspect the ST NO. 1 relay.
Click hereEngine / Hybrid System>V35A-FTS (STARTING)>RELAY>ON-VEHICLE INSPECTION
Inspect the ST NO. 2 relay.
Click hereEngine / Hybrid System>V35A-FTS (STARTING)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | NO. 2 Engine Room Relay Block and Junction Block Assembly |
| *a | ST NO. 1 Relay Terminal |
| *b | ST NO. 2 Relay Terminal |
Remove the ST NO. 1 and ST NO. 2 relays from the NO. 2 engine room relay block and junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay terminal 5 - Body ground | Always | 9.5 to 14 V |
| ST NO. 2 relay terminal 5 - Body ground | Always | 9.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 and ST NO. 2 relays from the NO. 2 engine room relay block and junction block assembly.
Disconnect the starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C52)Location & Routingewd_type=routing;type=c;code=C52 |
||
| ST NO. 1 relay terminal 3 - C52-2 (ST) | Always | Below 1 Ω |
| ST NO. 2 relay terminal 3 - C52-1 (SL2) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relays from the NO. 2 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay terminal 1 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 2 relay from the NO. 2 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 2 relay terminal 1 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the certification ECU (smart key ECU assembly) connector.
Disconnect the park/neutral position switch assembly connector.
Disconnect the engine stop and start ECU connector.
Remove the ST NO. 1 relay from the NO. 2 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B38)Location & Routingewd_type=routing;type=c;code=B38 |
||
| B38-21 (STA) - ST NO. 1 relay terminal 2 | Always | Below 1 Ω |
| B38-21 (STA) - Body ground | Always | 10 kΩ or higher |
| ST NO. 1 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Disconnect the engine stop and start ECU connector.
Remove the ST NO. 2 relay from the NO. 2 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B38)Location & Routingewd_type=routing;type=c;code=B38 Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECUewd_type=component;type=c;code=B38;pinno=23 |
||
| B38-23 (STA2) - ST NO. 2 relay terminal 2 | Always | Below 1 Ω |
| B38-23 (STA2) - Body ground | Always | 10 kΩ or higher |
| ST NO. 2 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the starter assembly.
Click hereEngine / Hybrid System>V35A-FTS (STARTING)>STARTER (w/ Stop And Start System)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Remove the ST NO. 1 and ST NO. 2 relays from the NO. 2 engine room relay block and junction block assembly.
Disconnect the certification ECU (smart key ECU assembly) connector.
Disconnect the engine stop and start ECU connector.
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B38)Location & Routingewd_type=routing;type=c;code=B38 Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECUewd_type=component;type=c;code=B38;pinno=21,23 |
||
| B38-21 (STA) - ST NO. 1 relay terminal 2 | Always | Below 1 Ω |
| B38-23 (STA2) - ST NO. 2 relay terminal 2 | Always | Below 1 Ω |
| B38-21 (STA) - Body ground | Always | 10 kΩ or higher |
| B38-23 (STA2) - Body ground | Always | 10 kΩ or higher |
| ST NO. 1 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| ST NO. 2 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL
If arriving at this item from the item "Drive command is being sent from the engine stop and start ECU but the starter itself is not moving" of "After Engine Stops due to Stop and Start System, Engine does not Restart" in Stop and Start / Stop and Start System / Problem Symptoms Table, go to SIMULATION METHOD.
NG
| *a | Component with harness connected (Engine Stop and Start ECU) |
- | - |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B38)Location & Routingewd_type=routing;type=c;code=B38 Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECUewd_type=component;type=c;code=B38;pinno=21,6 |
||
| B38-21 (STA) - B38-6 (DGND) | Engine start | 6 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ST NO. 1 relay.
Click hereEngine / Hybrid System>F33A-FTV (STARTING)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | NO. 4 Engine Room Relay Block and Junction Block Assembly |
| *a | ST NO. 1 Relay |
Remove the ST NO. 1 relays from the NO. 4 engine room relay block and junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay terminal 5 - Body ground | Always | 9.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relays from the NO. 4 engine room relay block and junction block assembly.
Disconnect the starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C181,C182)Location & Routingewd_type=routing;type=c,c;code=C181,C182 |
||
| ST NO. 1 relay terminal 3 - C181-1 (ST) | Always | Below 1 Ω |
| ST NO. 1 relay terminal 3 - C182-1 (ZYV) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relays from the NO. 4 engine room relay block and junction block assembly
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay terminal 1 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the engine stop and start ECU connector.
Remove the ST NO. 1 relays from the NO. 4 engine room relay block and junction block assembly.
Disconnect the certification ECU (smart key ECU assembly) connector.
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B38)Location & Routingewd_type=routing;type=c;code=B38 |
||
| B38-21 (STA) - ST NO. 1 relay terminal 2 | Always | Below 1 Ω |
| B38-21 (STA) - Body ground | Always | 10 kΩ or higher |
| ST NO. 1 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the engine stop and start ECU connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B37)Location & Routingewd_type=routing;type=c;code=B37 Click Connector(B37)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECUewd_type=component;type=c;code=B37;pinno=1,3 |
||
| B37-1 (BIN2) - Body ground | Always | 9.5 to 14 V |
| B37-3 (BIN1) - Body ground | Always | 9.5 to 14 V |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B38,I57)Location & Routingewd_type=routing;type=c,c;code=B38,I57 Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECUewd_type=component;type=c;code=B38;pinno=1 |
||
| B38-1 (+B) - Body ground | Ignition switch ON | 9.5 to 14 V |
| I57-21 (IGR) - Body ground | Ignition switch ON | 9.5 to 14 V |
| I57-18 (IGP) - Body ground | Ignition switch ON | 9.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the engine stop and start ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B37,B38)Location & Routingewd_type=routing;type=c,c;code=B37,B38 Click Connector(B37)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECUewd_type=component;type=c;code=B37;pinno=2,8 Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECUewd_type=component;type=c;code=B38;pinno=6 |
||
| B37-2 (GND2) - Body ground | Always | Below 1 Ω |
| B37-8 (GND1) - Body ground | Always | Below 1 Ω |
| B38-6 (DGND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL
If arriving at this item from the item "Drive command is being sent from the engine stop and start ECU but the starter itself is not moving" of "After Engine Stops due to Stop and Start System, Engine does not Restart" in Stop and Start / Stop and Start System / Problem Symptoms Table, go to SIMULATION METHOD.
NG