Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM
RM37H0E _53 Suspension _097405 FRONT SUSPENSION _0455869 FRONT LOWER SUSPENSION ARM A

FRONT SUSPENSION  FRONT LOWER SUSPENSION ARM  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C452119N03
1.75,1.667 1.75,1.083 1.75,1.083 1.917,1.083 false 5.167,0.833 5.167,0.25 5.167,0.25 5.333,0.25 false 3.5,1.417 3.5,0.833 3.5,0.833 3.667,0.833 false 6.813,0.219 6.5,0.219 true 3.802,2.75 3.635,2.75 3.635,2.75 3.635,2.458 true 6.323,0.083 6.604,0.438 0.281,0.354 18 false 1 2,0.938 2.229,1.26 0.229,0.323 18 false 2 5.427,0.094 5.708,0.448 0.281,0.354 18 false 4 1.583,3.198 2.042,3.396 0.458,0.198 10 false x 12 3.229,3.125 3.688,3.323 0.458,0.198 10 false x 3 3.719,2.302 4.177,2.5 0.458,0.198 10 false x 7 5.615,1.875 6.073,2.073 0.458,0.198 10 false x 11 3.719,0.688 4,1 0.281,0.313 18 false 3 3.885,2.688 4.344,2.885 0.458,0.198 10 false ●★

Procedure Part Name Code
Z101186

Z101188

Z101187

1 DISABLE BRAKE CONTROL - - - (Click here)
2 FRONT COMPARTMENT UNDER COVER 51441N - - -
3 FRONT LOWER SUSPENSION MEMBER PROTECTOR 51219 - - -
4 FRONT COMPARTMEMT UNDER COVER ASSEMBLY 51420A - - -

● Non-reusable part ★ Precoated part

C450001N05
6.469,4.635 6.688,4.635 true 1.219,4.302 1.385,4.688 1.385,4.688 1.552,4.688 true 5.792,2.552 5.875,2.094 5.875,2.094 6.042,2.094 true 4.135,3.448 4.469,3.448 true 2.667,3.417 2.75,3.583 2.75,3.583 2.917,3.583 true 6.75,4.5 7.156,4.792 0.406,0.292 18 false 5 1.615,4.563 2.021,4.854 0.406,0.292 18 false 6 6.438,1.938 6.844,2.229 0.406,0.292 18 false 7 4.854,3.292 5.26,3.583 0.406,0.292 18 false 8 3.031,3.427 3.271,3.76 0.24,0.333 18 false 9 4.635,2.313 4.948,2.51 0.313,0.198 10 false x 2 5.125,1.479 5.438,1.677 0.313,0.198 10 false x 2 3.375,1.875 3.688,2.073 0.313,0.198 10 false x 3

Procedure Part Name Code
Z101186

Z101188

Z101187

5 FRONT TIRE - - - -
6 FRONT SKID CONTROL SENSOR WIRE LH 89516F - - -
7 DISC BRAKE CYLINDER ASSEMBLY LH 47750 (Click here) - -
8 FRONT DISC 43516 (Click here) - -
9 FRONT DISC BRAKE DUST COVER LH 47782 - - -

C448104N02
2.615,4.719 2.448,4.719 2.448,4.719 2.333,4.542 true 6.354,3.021 6.271,2.458 6.271,2.458 6.104,2.458 true 5.5,5.438 5.917,5.438 true 3.583,4.333 3.896,4.333 true 3.938,5 4.177,5 true 0.844,3.427 1.198,3.427 true 3.844,5.531 4.083,5.531 true 3.667,3.583 3.5,3.583 3.5,3.583 3.5,3.74 true 5.385,4.365 5.615,4.365 true 4.667,3.927 4.865,3.927 true 5.833,4.083 5.917,4.083 5.917,4.083 5.917,3.865 true 6.917,3.833 6.917,3.583 true 2.896,4.604 3.271,4.896 0.375,0.292 18 false 16 3.99,3.792 4.76,4.177 0.771,0.385 18 false 10, 11 5.406,2.333 6.125,2.656 0.719,0.323 18 false 13, 14 4.5,4.865 4.875,5.156 0.375,0.292 18 false 15 6.24,5.302 6.615,5.594 0.375,0.292 18 false 12 1.458,3.302 1.833,3.594 0.375,0.292 18 false 17 3.979,4.219 4.354,4.51 0.375,0.292 18 false 18 3.719,3.479 3.917,3.688 0.198,0.208 10 false ● 4.156,5.417 4.417,5.667 0.26,0.25 10 false ● 5.708,3.99 5.865,4.188 0.156,0.198 10 false ● 5.667,4.26 5.865,4.5 0.198,0.24 10 false ● 6.885,3.844 7.073,4.063 0.188,0.219 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

10 DISCONNECT LOWER NO. 2 SUSPENSION ARM ASSEMBLY LH 48670A (Click here) - -
11 REMOVE LOWER NO. 2 SUSPENSION ARM ASSEMBLY LH 48670A (Click here) - -
12 TIE ROD ASSEMBLY LH 45470 (Click here) -
13 DISCONNECT STEERING KNUCKLE LH 43212 (Click here) - -
14 REMOVE STEERING KNUCKLE LH 43212 (Click here) - -
15 FRONT LOWER BALL JOINT ASSEMBLY LH 43340A (Click here) - -
16 FRONT STABILIZER LINK ASSEMBLY LH 48810 (Click here) - -
17 FRONT SHOCK ABSORBER ASSEMBLY LH 48520 (Click here) - -
18 FRONT LOWER SUSPENSION ARM ASSEMBLY LH 48640 - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front lower suspension arm removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link

*: The vehicle height changes because of suspension or tire replacement.

Suspension, tires, etc.*
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Advanced park


w/ Advanced Park:
(Click here)
w/o Advanced Park:
(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assisr ECU initilization

·

Adjust sttering angle

·

Rear television camera view adjustment (for Rear camera detection system)


Panoramic view monitor system (Click here)
Perform headlight ECU sub-assembly LH initialization Automatic headlight beam level control system (Click here)
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Wheel alignment adjustment Perform "Calibration" Electronically controlled brake system malfunctions (Click here)


NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.

·

When removing or installing the front disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, theservo motor and expansion valve standardposition is recognized. -

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. DISABLE BRAKE CONTROL

Z101186

Click here(Click here)

Hide 51441N 2.REMOVE FRONT COMPARTMENT UNDER COVER

Hide 51219 3.REMOVE FRONT LOWER SUSPENSION MEMBER PROTECTOR

Hide 51420A 4.REMOVE FRONT COMPARTMEMT UNDER COVER ASSEMBLY

Hide 5.REMOVE FRONT TIRE

Hide 89516F 6.DISCONNECT FRONT SKID CONTROL SENSOR WIRE LH

Hide 47750 7.DISCONNECT DISC BRAKE CYLINDER ASSEMBLY LH

Z101186

Click here(Click here)

Hide 43512 8.REMOVE FRONT DISC

Z101186

Click here(Click here)

Hide 47782 9.REMOVE FRONT DISC BRAKE DUST COVER LH

Hide 48670A 10.DISCONNECT LOWER NO. 2 SUSPENSION ARM ASSEMBLY LH

a.
C452116C01
2.313,3.865 2.917,4.333 2.917,4.333 3.083,4.333 true 5.75,3.615 6,4.083 6,4.083 6.167,4.083 true 6.24,3.417 6.552,3.615 0.313,0.198 10 false *a 3.167,4.26 3.583,4.5 0.417,0.24 10 false SST 6.229,4.01 6.583,4.333 0.354,0.323 10 false SST 1.917,0.083 2.198,0.438 0.281,0.354 18 false i 0.448,2.323 0.979,2.667 0.531,0.344 18 true ii, iii
*a 2 mm (0.0787 in.) - -


i.

Remove the clip and nut.


ii.

Install SST (attachment) onto the lower No. 2 suspension arm assembly LH so that there is a space of approximately 2 mm (0.0787 in.) between the arm and attachment.

SST
09628-50010  (09628-05010)

NOTICE:
·

Be sure to install SST (attachment) in order to prevent damage to the lower No. 2 suspension arm assembly LH stud.

·

As SST may become damaged, make sure the space between the arm and spacers is not 2 mm (0.0787 in.) or less.




iii.

Using SST, disconnect the lower No. 2 suspension arm assembly LH from the front lower ball joint assembly LH.

SST
09628-50010  (09628-05010)

NOTICE:
·

Apply molybdenum grease to the bolt threads and end of the SST bolt.

·

Do not damage the dust cover of the lower No. 2 suspension arm assembly LH.

·

Make sure that the bolt of SST and thelower No. 2 suspension arm assembly LH ball are in a straight line when installing SST.

·

Be sure to tie the string of SST to the vehicle to prevent SST from dropping.

·

Do not apply a torque of 160 N*m (1631 kgf*cm, 118 ft.*lbf) or more to SST as it may be damaged.





Hide 48670A 11.REMOVE LOWER NO. 2 SUSPENSION ARM ASSEMBLY LH

a.
C448109


Hide 45470 12.DISCONNECT TIE ROD ASSEMBLY LH

Z101186

Click here(Click here)

Hide 43212 13.DISCONNECT STEERING KNUCKLE LH

Z101186

Click here(Click here)

Hide 43212 14.REMOVE STEERING KNUCKLE LH

Hide 43340A 15.REMOVE FRONT LOWER BALL JOINT ASSEMBLY LH

Z101186

Click here(Click here)

Hide 48810 16.REMOVE FRONT STABILIZER LINK ASSEMBLY LH

Z101186

Click here(Click here)

Hide 48520 17.DISCONNECT FRONT SHOCK ABSORBER ASSEMBLY LH

a.
C448110N01
0.396,0.052 0.677,0.406 0.281,0.354 18 false i

i.

Remove the bolt and nut, and separate the front shock absorber assembly LH from the lower suspension arm assembly LH.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.




Hide 48640 18.REMOVE FRONT LOWER SUSPENSION ARM ASSEMBLY LH

a.
C452117