MALFUNCTION DESCRIPTION
The EV control ECU detects a malfunction in the system shut-off signal (ISDN signal) which is sent from the FCDC converter control ECU.
The likely causes of the malfunction are as follows.
Wire harness malfunction
FCDC converter control ECU malfunction
EV control ECU malfunction
Wire harness malfunction
Inverter with converter assembly malfunction
EV control ECU malfunction
For the HSDN signal system description, refer to the DTC P321E9F.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P321E9F
For the FSDN and ISDN signal system description, refer to the DTC P1D9512.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1D9512
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority |
|---|---|---|---|---|---|---|
| P1E0A12 | FC Converter Fail Signal Circuit Short to Battery | The FSDN signal from the EV control ECU is OFF but the CPU monitored value of the HSDN signal is ON.
(1 trip detection logic) |
·
Wire harness or connector ·
EV control ECU ·
FCDC converter control ECU board sub-assembly ·
FC converter power module transistor ·
Inverter with converter assembly |
Master Warning:
Comes on |
EV | A |
| P1E0A14 | FC Converter Fail Signal Circuit Short to Ground or Open | The FSDN signal from the EV control ECU is ON but the CPU monitored value of the HSDN signal is OFF.
(1 trip detection logic) |
·
Wire harness or connector ·
EV control ECU ·
FCDC converter control ECU board sub-assembly ·
FC converter power module transistor ·
Inverter with converter assembly |
Master Warning:
Comes on |
EV | A |
| DTC No. | Data List |
|---|---|
| P1E0A12
P1E0A14 |
·
Emergency Shutdown Signal (FC) ·
FC Converter Shutdown Signal ·
Inverter Emergency Shutdown (Main CPU) ·
Inverter Emergency Shutdown (Sub CPU) |
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY
Turn the ignition switch off and wait for 10 minutes or more.
Turn the ignition switch to ON (READY) and wait for 30 seconds.
Turn the ignition switch off and wait for 10 minutes or more.
Enter the following menus: Powertrain / EV / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform driving pattern again.
For the HSDN signal system circuit diagram, refer to the shutdown signal system.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Shut Down Signal Circuit
For the FSDN and ISDN signal system circuit diagrams, refer to P1D9512.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1D9512
Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.
Make sure to remove the service plug grip first.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the inverter with converter assembly
Disconnecting the low voltage connector of the EV supply battery assembly
Disconnecting the low voltage connector of the FC converter assembly
Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)
To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.
After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.
The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.
Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.
| *a | Without waiting for 10 minutes |
After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.
Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.
If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.
Since high voltage accumulates within the FC stack assembly with FC converter, never perform the work of separating the FC stack assembly with FC converter into the FC converter assembly and FC stack assembly without first performing electrical charge discharge (forced electrical charge discharge or electrical charge self-discharge), because doing so is dangerous.
Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL
Removing and installing the FC stack assembly without first discharging the electrical charge may result in an electric shock due to the high voltage circuit.
After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the auxiliary battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.
When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)
Pre-procedure1
None.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| P1E0A12 or P1E0A14 only is output, or DTCs except the ones in the table below are also output. | A |
| DTCs of EV control system in the tables below are output. | B |
| DTCs of FC boost control system in the tables below are output. | C |
| Malfunction Content | System | Relevant DTC | |
|---|---|---|---|
| Microcomputer malfunction | Hybrid control system | P0A1B49 | Drive Motor "A" Control Module Internal Electronic Failure |
| P060647 | Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure | ||
| P060687 | Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message | ||
| P060A47 | Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure | ||
| P060A87 | Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message | ||
| P060B49 | Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure | ||
| P060B71 | Hybrid/EV Powertrain Control Module A/D Processing Actuator Stuck | ||
| P060B1C | Sensor Power Supply "A" Circuit/Open Circuit Voltage Out of Range | ||
| P1C9E9F | Hybrid/EV System Reset Stuck Off | ||
| FC control system | P060B16 | Internal Control Module A/D Processing Performance Circuit Voltage Below Threshold | |
| Power source circuit malfunction | FC control system | P1F451F | FC Converter Control Module Power Relay Sense Circuit Intermittent |
| P1F651C | FC Converter Control Module Power Supply (-5V) Circuit Voltage Out of Range | ||
| P1F661C | FC Converter Control Module Power Supply (+V5AREF) Circuit Voltage Out of Range | ||
| Communication system malfunction | Hybrid control system | P312387 | Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message |
| FC control system | U116087 | Lost Communication with FCDC Control Module Missing Message | |
| U029387 | Lost Communication with Hybrid/EV Powertrain Control Module Missing Message | ||
| System malfunction | Hybrid control system | P321E9F | Motor/Generator Shutdown Signal Stuck Off |
| P33B99F | Motor/Generator Shutdown Signal (Hybrid/EV Side) Stuck Off | ||
| FC control system | P1DDA9E | FC Converter Phase U Fail Signal Stuck On | |
| P1DDB9E | FC Converter Phase V Fail Signal Stuck On | ||
| P1DDC9E | FC Converter Phase W Fail Signal Stuck On | ||
| P1DDD9E | FC Converter Phase X Fail Signal Stuck On | ||
| P1F0117 | FC Converter Output Voltage Circuit Voltage Above Threshold | ||
| P1F009E | FC Converter Overvoltage Signal Stuck On | ||
The chart above is listed in inspection order of priority.
Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
Post-procedure1
Turn the ignition switch off.
A
B
C
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P056014
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A001C
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip is not installed to FC stack assembly and EV battery.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Disconnect the A17 EV control ECU connector.
Disconnect the A19*1 or A18*2 inverter with converter assembly connector.
*1: for LHD
*2: for RHD
Procedure1
Measure the resistance according to the value(s) in the table below.
| *A | for LHD | *B | for RHD |
| *a | Front view of wire harness connector
(to Inverter with Converter Assembly) |
*b | Rear view of wire harness connector
(to EV control ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A17,A19)Location & Routingewd_type=routing;type=c,c;code=A17,A19 Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECUewd_type=component;type=c;code=A17;pinno=8 |
||
| A17-8 (HSDN) - A19-25 (HSDN) | Ignition switch off | Below 1 Ω |
| A17-8 (HSDN) or A19-25 (HSDN) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A17,A18)Location & Routingewd_type=routing;type=c,c;code=A17,A18 Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECUewd_type=component;type=c;code=A17;pinno=8 |
||
| A17-8 (HSDN) - A18-25 (HSDN) | Ignition switch off | Below 1 Ω |
| A17-8 (HSDN) or A18-25 (HSDN) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the A19*1 or A18*2 inverter with converter assembly connector.
*1: for LHD
*2: for RHD
Reconnect the A17 EV control ECU connector.
OK
NG
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip and FC converter power outlet cable are not installed.
After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Reconnect the A19*1 or A18*2 inverter with converter assembly connector.
*1: for LHD
*2: for RHD
Procedure1
| *A | for LHD |
| *B | for RHD |
| *a | Component without harness connected
(Inverter with Converter Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A19)Location & Routingewd_type=routing;type=c;code=A19 |
||
| A19-25 (HSDN) - A19-30 (GND1) | Ignition switch off | 2.65 to 3.55 kΩ |
| A19-25 (HSDN) - A19-10 (+B) | Ignition switch off | 5 kΩ or higher |
| A19-25 (HSDN) - A19-11 (+B2) | Ignition switch off | 5 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A18)Location & Routingewd_type=routing;type=c;code=A18 |
||
| A18-25 (HSDN) - A18-30 (GND1) | Ignition switch off | 2.65 to 3.55 kΩ |
| A18-25 (HSDN) - A18-10 (+B) | Ignition switch off | 5 kΩ or higher |
| A18-25 (HSDN) - A18-11 (+B2) | Ignition switch off | 5 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the A19*1 or A18*2 inverter with converter assembly connector.
*1: for LHD
*2: for RHD
OK
NG
Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1D0619
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector) | C |
A
B
C
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip and FC converter power outlet cable are not installed.
After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Disconnect the A16 EV control ECU connector.
Remove the electric heater sub-assembly.
Disconnect the B6 FC converter assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to FC Converter Assembly) |
*b | Rear view of wire harness connector
(to EV Control ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(B6,A16)Location & Routingewd_type=routing;type=c,c;code=B6,A16 Click Connector(B6)Engine Compartment>No. 2 Stack Wire>FC Converter Assemblyewd_type=component;type=c;code=B6;pinno=4 Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECUewd_type=component;type=c;code=A16;pinno=20 |
||
| B6-4 (ISDN) - A16-20 (ISDN) | Ignition switch off | Below 1 Ω |
| B6-4 (ISDN) or A16-20 (ISDN) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the B6 FC converter assembly connector.
Install the electric heater sub-assembly.
Reconnect the A16 EV control ECU connector.
OK
NG
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip and FC converter power outlet cable are not installed.
After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the electric heater sub-assembly connector.
Disconnect the B6 FC converter assembly connector.
Procedure1
| *a | Component without harness connected
(FC Converter Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(B6)Location & Routingewd_type=routing;type=c;code=B6 Click Connector(B6)Engine Compartment>No. 2 Stack Wire>FC Converter Assemblyewd_type=component;type=c;code=B6;pinno=4,10,12,2,11,13,6 |
||
| B6-4 (ISDN) - B6-10 (E1) | Ignition switch off | 2.65 to 3.55 kΩ |
| B6-4 (ISDN) - B6-12 (+B1) | Ignition switch off | 5 kΩ or higher |
| B6-4 (ISDN) - B6-2 (DRN0) | Ignition switch off | 10 kΩ or higher |
| B6-4 (ISDN) - B6-11 (E2) | Ignition switch off | 10 kΩ or higher |
| B6-4 (ISDN) - B6-13 (+B2) | Ignition switch off | 5 kΩ or higher |
| B6-4 (ISDN) - B6-6 (IG2) | Ignition switch off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the B6 FC converter assembly connector.
Install the electric heater sub-assembly connector.
OK
NG
Pre-procedure1
Disconnect the B6 FC converter assembly connector.
Procedure1
| *a | Component with harness connected
(EV Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A16,A17)Location & Routingewd_type=routing;type=c,c;code=A16,A17 Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECUewd_type=component;type=c;code=A16;pinno=20 Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECUewd_type=component;type=c;code=A17;pinno=4 |
||
| A16-20 (ISDN) - A17-4 (E1) | Ignition switch off | 2.65 to 3.55 kΩ |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the B6 FC converter assembly connector.
OK
NG
Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT