Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P312387  Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message  


DESCRIPTION

Refer to the description for DTC P0D2D16.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0D2D16

The MG ECU, which is built into in the inverter with converter assembly, controls motor (MG2) based on commands from the EV control ECU. The MG ECU monitors communication data and detects malfunctions.

The EV control ECU monitors communication data and detects malfunctions.

A communication error between the MG ECU and the EV control ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message Error in reception from inverter with converter assembly (MG ECU) via serial communication (out of communication standard)
(1 trip detection logic)
·

Wire harness or connector

·

Inverter with converter assembly

·

FCV with motor transaxle assembly

·

FC air compressor with motor assembly

·

EV control ECU

·

IGCT NO.4 fuse


Master Warning:
Comes on
EV A

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON and wait for 2 minutes or more.

4.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for the inverter low-voltage circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Inverter Low-voltage Circuit

Refer to the wiring diagram for DTC P0AA649.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA649

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.INSPECT FUSE (IGCT NO.4)

Pre-procedure1

a.

Remove the IGCT NO.4 fuse from the Luggage Room Relay Block.


Procedure1

a.
A481450C01
1.677,1.01 1.99,0.625 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *1 2.031,0.563 2.344,0.719 0.313,0.156 10 false *2
*1 Luggage Room Relay Block
*2 IGCT NO.4 Fuse


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT NO.4 fuse terminals Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the IGCT NO.4 fuse.



OK

2.CLEAR DTC

NG

18.REPLACE FUSE (IGCT NO.4)
2.CLEAR DTC

NEXT

3.CHECK DTC OUTPUT (EV)
3.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 2 minutes or more.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P312387 is output A
P312387 is not output B



Post-procedure1

a.

Turn the ignition switch off.



A

4.CHECK INVERTER WITH CONVERTER ASSEMBLY (FC AIR COMPRESSOR MOTOR CABLE CONNECTION CONDITION)

B

4.CHECK INVERTER WITH CONVERTER ASSEMBLY (FC AIR COMPRESSOR MOTOR CABLE CONNECTION CONDITION)
HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>FC Air Compressor High-voltage Circuit


Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



A

5.CHECK INVERTER WITH CONVERTER ASSEMBLY (NO. 2 BATTERY PACK WIRE CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

5.CHECK INVERTER WITH CONVERTER ASSEMBLY (NO. 2 BATTERY PACK WIRE CONNECTION CONDITION)
HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Motor High-voltage Circuit


Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



A

6.CHECK FC AIR COMPRESSOR WITH MOTOR ASSEMBLY

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

6.CHECK FC AIR COMPRESSOR WITH MOTOR ASSEMBLY

OK

7.INSPECT FCV WITH MOTOR TRANSAXLE ASSEMBLY

NG

REPLACE FC AIR COMPRESSOR WITH MOTOR ASSEMBLY

7.INSPECT FCV WITH MOTOR TRANSAXLE ASSEMBLY

OK

8.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)

NG

8.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


Procedure1

a.
C361311C90
0.042,0.583 0.479,0.948 0.438,0.365 0.042,1.063 0.479,1.427 0.438,0.365 1.802,1.865 2.083,1.365 true 2.521,1.865 2.229,1.365 true 2.24,1.052 2.521,0.552 true 2.073,1.052 1.781,0.552 true 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 1.635,1.885 2.25,2.083 0.615,0.198 10 false GND1 2.385,1.885 3,2.083 0.615,0.198 10 false GND2 1.625,0.375 1.938,0.573 0.313,0.198 10 false +B 2.531,0.385 2.844,0.583 0.313,0.198 10 false +B2 0.146,0.688 0.604,0.885 0.458,0.198 10 false A19 0.156,1.156 0.615,1.354 0.458,0.198 10 false A18 0.542,0.708 0.854,0.906 0.313,0.198 10 false *A 0.542,1.167 0.854,1.365 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A19-30 (GND1) - Body ground Ignition switch off Below 1 Ω
A19-31 (GND2) - Body ground Ignition switch off Below 1 Ω

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A18-30 (GND1) - Body ground Ignition switch off Below 1 Ω
A18-31 (GND2) - Body ground Ignition switch off Below 1 Ω



b.

Connect the cable to the negative (-) auxiliary battery terminal and wait for 2 minutes or more.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A19-10 (+B) - Body ground Ignition switch ON 11 to 14 V
A19-11 (+B2) - Body ground Ignition switch ON 11 to 14 V

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A18-10 (+B) - Body ground Ignition switch ON 11 to 14 V
A18-11 (+B2) - Body ground Ignition switch ON 11 to 14 V


NOTICE:

Turning the ignition switch to ON with the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

9.CHECK EV CONTROL ECU (CLK CHECK WAVEFORM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)

9.CHECK EV CONTROL ECU (CLK CHECK WAVEFORM)

Pre-procedure1

a.

Turn the ignition switch to ON.


b.

Connect an oscilloscope between the EV control ECU terminals specified in the table below.


Procedure1

a.
A481541C01
1.469,0.365 1.906,0.677 0.438,0.313 2.052,0.375 2.5,0.677 0.448,0.302 1.438,1.854 1.656,1.146 true 2.052,1.833 1.719,1.146 true 2.635,1.833 2.26,1.063 true 0.094,0.094 0.406,0.25 0.313,0.156 10 false *a 1.583,0.458 1.896,0.615 0.313,0.156 10 false A16 2.177,0.458 2.563,0.615 0.385,0.156 10 false A17 2.021,1.854 2.469,2.094 0.448,0.24 10 false CLK+ 1.229,1.854 1.677,2.094 0.448,0.24 10 false CLK- 2.594,1.833 3.042,2.073 0.448,0.24 10 false E1 0.24,2.875 0.688,3.115 0.448,0.24 10 false CH1 0.219,3.625 0.667,3.865 0.448,0.24 10 false CH2 2.802,3.396 3.25,3.635 0.448,0.24 10 false GND 2.792,3.958 3.24,4.198 0.448,0.24 10 false GND
*a Component with harness connected
(EV Control ECU)


Measure the waveform.

Tester Connection Condition Equipment Setting

Click Location & Routing(A16,A17)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

CH1: A16-12 (CLK+) - A17-4 (E1)
CH2: A16-13 (CLK-) - A17-4 (E1)
Ignition switch ON 1 V/DIV, 1 μs/DIV

HINT:
·

Inspect with the connector connected.

·

If pulses are generated, the shape of the waveform can be assumed to be normal.

·

The shape of the waveform may vary according to communication conditions.



Result:
Result Proceed to
There is an interruption or distortion in the waveform A
There are no interruptions or distortions in the waveform B



Post-procedure1

a.

Turn the ignition switch off.



A

10.CHECK EV CONTROL ECU (REQ CHECK WAVEFORM)

B

16.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
10.CHECK EV CONTROL ECU (REQ CHECK WAVEFORM)

Pre-procedure1

a.

Turn the ignition switch to ON.


b.

Connect an oscilloscope between the EV control ECU terminals specified in the table below.


Procedure1

a.
A481542C02
1.469,0.365 1.896,0.677 0.427,0.313 2.063,0.365 2.49,0.677 0.427,0.313 1.323,1.833 1.573,1.146 true 2.063,1.854 1.635,1.146 true 2.677,1.823 2.26,1.063 true 0.094,0.094 0.406,0.25 0.313,0.156 10 false *a 1.573,0.458 1.885,0.615 0.313,0.156 10 false A16 2.177,0.448 2.563,0.604 0.385,0.156 10 false A17 2.021,1.854 2.469,2.094 0.448,0.24 10 false REQ+ 1.188,1.844 1.635,2.083 0.448,0.24 10 false REQ- 2.656,1.833 3.104,2.073 0.448,0.24 10 false E1 0.313,2.875 0.76,3.115 0.448,0.24 10 false CH1 0.302,3.542 0.75,3.781 0.448,0.24 10 false CH2 2.927,3.344 3.375,3.583 0.448,0.24 10 false GND 2.917,3.906 3.365,4.146 0.448,0.24 10 false GND
*a Component with harness connected
(EV Control ECU)


Measure the waveform.

Tester Connection Condition Equipment Setting

Click Location & Routing(A16,A17)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

CH1: A16-14 (REQ+) - A17-4 (E1)
CH2: A16-15 (REQ-) - A17-4 (E1)
Ignition switch ON 1 V/DIV, 1 μs/DIV

HINT:
·

Inspect with the connector connected.

·

If pulses are generated, the shape of the waveform can be assumed to be normal.

·

The shape of the waveform may vary according to communication conditions.



Result:
Result Proceed to
There is an interruption or distortion in the waveform A
There are no interruptions or distortions in the waveform B



Post-procedure1

a.

Turn the ignition switch off.



A

11.CHECK EV CONTROL ECU (MTH CHECK WAVEFORM)

B

14.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
11.CHECK EV CONTROL ECU (MTH CHECK WAVEFORM)

Pre-procedure1

a.

Turn the ignition switch to ON.


b.

Connect an oscilloscope between the EV control ECU terminals specified in the table below.


Procedure1

a.
A481543C01
1.469,0.365 1.885,0.677 0.417,0.313 2.073,0.365 2.49,0.677 0.417,0.313 1.208,1.844 1.49,1.146 true 2.021,1.865 1.552,1.146 true 2.667,1.813 2.26,1.063 true 0.094,0.094 0.406,0.25 0.313,0.156 10 false *a 1.573,0.448 1.885,0.604 0.313,0.156 10 false A16 2.188,0.458 2.573,0.615 0.385,0.156 10 false A17 2.021,1.854 2.469,2.094 0.448,0.24 10 false MTH+ 0.979,1.844 1.427,2.083 0.448,0.24 10 false MTH- 2.667,1.833 3.115,2.073 0.448,0.24 10 false E1 0.323,2.792 0.771,3.031 0.448,0.24 10 false CH1 0.302,3.49 0.75,3.729 0.448,0.24 10 false CH2 2.927,3.208 3.375,3.448 0.448,0.24 10 false GND 2.917,3.813 3.365,4.052 0.448,0.24 10 false GND
*a Component with harness connected
(EV Control ECU)


Measure the waveform.

Tester Connection Condition Equipment Setting

Click Location & Routing(A16,A17)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

CH1: A16-16 (MTH+) - A17-4 (E1)
CH2: A16-17 (MTH-) - A17-4 (E1)
Ignition switch ON 1 V/DIV, 200 μs/DIV

HINT:
·

Inspect with the connector connected.

·

If pulses are generated, the shape of the waveform can be assumed to be normal.

·

The shape of the waveform may vary according to communication conditions.



Result:
Result Proceed to
There is an interruption or distortion in the waveform A
There are no interruptions or distortions in the waveform B



Post-procedure1

a.

Turn the ignition switch off.



A

B

12.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
12.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


c.

Disconnect the A16 EV control ECU connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

A480891C15
2.094,0.438 2.51,0.771 0.417,0.333 5.208,0.156 5.625,0.49 0.417,0.333 1.208,0.438 1.625,0.771 0.417,0.333 1.729,2.146 1.49,1.188 true 1.01,2.167 1.406,1.198 true 5,2.271 5.229,1.656 true 5.656,2.292 5.271,1.656 true 0.552,0.208 0.865,0.365 0.313,0.156 10 false *a 3.531,0.188 3.844,0.344 0.313,0.156 10 false *b 1.302,0.531 1.573,0.729 0.271,0.198 10 false A19 5.313,0.26 5.583,0.458 0.271,0.198 10 false A16 1.594,2.219 2.021,2.427 0.427,0.208 10 false MTH+ 0.885,2.229 1.313,2.438 0.427,0.208 10 false MTH- 4.813,2.302 5.24,2.51 0.427,0.208 10 false MTH- 5.635,2.302 6.063,2.51 0.427,0.208 10 false MTH+ 2.188,0.542 2.458,0.74 0.271,0.198 10 false A18 2.573,0.531 2.844,0.729 0.271,0.198 10 false *B 1.677,0.542 1.948,0.74 0.271,0.198 10 false *A
*A for LHD *B for RHD
*a Front view of wire harness connector
(Inverter with Converter Assembly)
*b Rear view of wire harness connector
(to EV Control ECU)


Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A16)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A16-16 (MTH+) - Body ground Ignition switch ON Below 1 V
A16-17 (MTH-) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the EV control ECUy connector and the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



b.

Turn the ignition switch off.


c.

Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 2 minutes or more.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A16,A19)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A16-16 (MTH+) - A19-3 (MTH+) Ignition switch off Below 1 Ω
A16-17 (MTH-) - A19-2 (MTH-) Ignition switch off Below 1 Ω
A16-16 (MTH+) or A19-3 (MTH+) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A16-17 (MTH-) or A19-2 (MTH-) - Body ground and other terminals Ignition switch off 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A16,A18)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A16-16 (MTH+) - A18-3 (MTH+) Ignition switch off Below 1 Ω
A16-17 (MTH-) - A18-2 (MTH-) Ignition switch off Below 1 Ω
A16-16 (MTH+) or A18-3 (MTH+) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A16-17 (MTH-) or A18-2 (MTH-) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A16 EV Control ECU connector.


b.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

13.CHECK INVERTER WITH CONVERTER ASSEMBLY (MTH INTERNAL RESISTANCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK INVERTER WITH CONVERTER ASSEMBLY (MTH INTERNAL RESISTANCE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


Procedure1

a.
A478491C23
1.417,0.917 1.844,1.271 0.427,0.354 1.438,1.76 1.167,2.563 true 1.49,1.771 1.656,2.583 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 1.521,1.031 1.823,1.198 0.302,0.167 10 false A16 1.01,2.615 1.396,2.802 0.385,0.188 10 false MTH- 1.563,2.615 2.104,2.781 0.542,0.167 10 false MTH+
*a Component with harness connected
(EV Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A16)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A16-16 (MTH+) - A16-17 (MTH-) Ignition switch off 109 to 131 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

14.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


c.

Disconnect the A16 EV control ECU connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

A480891C07
1.302,0.438 1.792,0.792 0.49,0.354 5.208,0.156 5.625,0.49 0.417,0.333 2.083,0.438 2.573,0.792 0.49,0.354 1.729,2.146 1.49,1.51 true 1.01,2.167 1.396,1.5 true 5.073,2.271 5.302,1.656 true 5.729,2.292 5.344,1.656 true 0.552,0.208 0.865,0.365 0.313,0.156 10 false *a 3.531,0.188 3.844,0.344 0.313,0.156 10 false *b 1.448,0.531 1.76,0.729 0.313,0.198 10 false A19 5.313,0.26 5.583,0.458 0.271,0.198 10 false A16 1.594,2.219 2.021,2.427 0.427,0.208 10 false REQ+ 0.885,2.229 1.313,2.438 0.427,0.208 10 false REQ- 4.885,2.302 5.313,2.51 0.427,0.208 10 false REQ- 5.635,2.302 6.063,2.51 0.427,0.208 10 false REQ+ 2.219,0.521 2.49,0.719 0.271,0.198 10 false A18 1.854,0.521 2.125,0.719 0.271,0.198 10 false *A 2.646,0.51 2.917,0.708 0.271,0.198 10 false *B
*A for LHD *B for RHD
*a Front view of wire harness connector
(Inverter with Converter Assembly)
*b Rear view of wire harness connector
(to EV Control ECU)


Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A16)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A16-14 (REQ+) - Body ground Ignition switch ON Below 1 V
A16-15 (REQ-) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the EV control ECU connector and the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



b.

Turn the ignition switch off.


c.

Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 2 minutes or more.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A16,A19)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A16-14 (REQ+) - A19-34 (REQ+) Ignition switch off Below 1 Ω
A16-15 (REQ-) - A19-33 (REQ-) Ignition switch off Below 1 Ω
A16-14 (REQ+) or A19-34 (REQ+) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A16-15 (REQ-) or A19-33 (REQ-) - Body ground and other terminals Ignition switch off 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A16,A18)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A16-14 (REQ+) - A18-34 (REQ+) Ignition switch off Below 1 Ω
A16-15 (REQ-) - A18-33 (REQ-) Ignition switch off Below 1 Ω
A16-14 (REQ+) or A18-34 (REQ+) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A16-15 (REQ-) or A18-33 (REQ-) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A16 EV Control ECU connector.


b.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

15.CHECK INVERTER WITH CONVERTER ASSEMBLY (REQ INTERNAL RESISTANCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK INVERTER WITH CONVERTER ASSEMBLY (REQ INTERNAL RESISTANCE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A16 EV control ECU connector.


Procedure1

a.
A478494C02
1.427,0.604 1.896,0.969 0.469,0.365 1.531,2.385 1.208,3.01 true 1.583,2.375 2.042,2.979 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 1.552,0.74 1.854,0.906 0.302,0.167 10 false A16 1.042,3.042 1.427,3.229 0.385,0.188 10 false REQ- 1.969,3.042 2.448,3.25 0.479,0.208 10 false REQ+
*a Component with harness connected
(EV Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A16)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A16-14 (REQ+) - A16-15 (REQ-) Ignition switch off 109 to 131 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A16 EV control ECU connector.



OK

NG

REPLACE INVERTER WITH CONVERTER ASSEMBLY

16.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


c.

Disconnect the A16 EV control ECU connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

A480891C08
2.052,0.438 2.469,0.771 0.417,0.333 5.208,0.156 5.625,0.49 0.417,0.333 1.25,0.438 1.667,0.771 0.417,0.333 1.729,2.146 1.479,1.271 true 1.021,2.167 1.396,1.26 true 5.031,2.292 5.385,1.656 true 5.813,2.292 5.427,1.656 true 0.552,0.208 0.865,0.365 0.313,0.156 10 false *a 3.531,0.188 3.844,0.344 0.313,0.156 10 false *b 2.135,0.531 2.406,0.729 0.271,0.198 10 false A18 5.313,0.26 5.583,0.458 0.271,0.198 10 false A16 1.594,2.219 2.021,2.427 0.427,0.208 10 false CLK+ 0.844,2.229 1.271,2.438 0.427,0.208 10 false CLK- 4.875,2.302 5.302,2.51 0.427,0.208 10 false CLK- 5.698,2.302 6.125,2.51 0.427,0.208 10 false CLK+ 1.354,0.521 1.635,0.729 0.281,0.208 10 false A19 1.729,0.542 2,0.74 0.271,0.198 10 false *A 2.531,0.542 2.802,0.74 0.271,0.198 10 false *B
*A for LHD *B for RHD
*a Front view of wire harness connector
(Inverter with Converter Assembly)
*b Rear view of wire harness connector
(to EV Control ECU)


Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A16)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A16-12 (CLK+) - Body ground Ignition switch ON Below 1 V
A16-13 (CLK-) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the EV control ECU connector and the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



b.

Turn the ignition switch off.


c.

Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 2 minutes or more.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A16,A19)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A16-12 (CLK+) - A19-14 (CLK+) Ignition switch off Below 1 Ω
A16-13 (CLK-) - A19-13 (CLK-) Ignition switch off Below 1 Ω
A16-12 (CLK+) or A19-14 (CLK+) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A16-13 (CLK-) or A19-13 (CLK-) - Body ground and other terminals Ignition switch off 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A16,A18)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A16-12 (CLK+) - A18-14 (CLK+) Ignition switch off Below 1 Ω
A16-13 (CLK-) - A18-13 (CLK-) Ignition switch off Below 1 Ω
A16-12 (CLK+) or A18-14 (CLK+) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A16-13 (CLK-) or A18-13 (CLK-) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A16 EV Control ECU connector.


b.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

17.CHECK INVERTER WITH CONVERTER ASSEMBLY (CLK INTERNAL RESISTANCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK INVERTER WITH CONVERTER ASSEMBLY (CLK INTERNAL RESISTANCE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A16 EV control ECU connector.


Procedure1

a.
A478494C03
1.438,0.677 1.875,1.031 0.438,0.354 1.625,2.385 1.302,3.01 true 1.688,2.375 2.146,2.979 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 1.552,0.792 1.854,0.958 0.302,0.167 10 false A16 1.125,3.042 1.51,3.229 0.385,0.188 10 false CLK- 2.01,3.031 2.479,3.198 0.469,0.167 10 false CLK+
*a Component with harness connected
(EV Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A16)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A16-12 (CLK+) - A16-13 (CLK-) Ignition switch off 109 to 131 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A16 EV control ECU connector.



OK

NG

REPLACE INVERTER WITH CONVERTER ASSEMBLY

18.REPLACE FUSE (IGCT NO.4)

Pre-procedure1

a.
A481450C01
1.677,1.01 1.99,0.625 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *1 2.031,0.563 2.344,0.719 0.313,0.156 10 false *2
*1 Luggage Room Relay Block
*2 IGCT NO.4 Fuse


Remove the IGCT NO.4 fuse from the Luggage Room Relay Block.


b.

Turn the ignition switch to on (READY).


Procedure1

a.

Check if there is an open circuit in the IGCT NO.4 fuse in the luggage room relay block.

OK:

There is no open circuit in the IGCT NO.4 fuse.


HINT:

If the fuse does not become open again after turning the ignition switch to ON (READY), it can be assumed that the previous fuse failed due to age.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.



OK

COMPLETED

NG

19.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - LUGGAGE ROOM RELAY BLOCK)
19.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - LUGGAGE ROOM RELAY BLOCK)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the IGCT NO. 4 fuse from the luggage room relay block.


c.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A481545C02
5.594,0.406 6.052,0.76 0.458,0.354 4.771,0.406 5.229,0.76 0.458,0.354 5.417,2.167 5.688,1.323 true 6.063,2.167 5.813,1.333 true 0.26,0.208 0.573,0.365 0.313,0.156 10 false *1 1.292,0.51 1.604,0.667 0.313,0.156 10 false *2 3.594,0.427 3.906,0.583 0.313,0.156 10 false *a 5.708,0.51 6.167,0.708 0.458,0.198 10 false A18 5.292,2.208 5.604,2.406 0.313,0.198 10 false +B 5.979,2.208 6.292,2.406 0.313,0.198 10 false +B2 4.875,0.521 5.333,0.719 0.458,0.198 10 false A19 5.313,0.521 5.771,0.719 0.458,0.198 10 false *A 6.115,0.531 6.573,0.729 0.458,0.198 10 false *B
*A for LHD *B for RHD
*1 Luggage Room Relay Block *2 IGCT NO. 4 Fuse
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
- -


Standard Resistance (Check for Short):
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A19-10 (+B), A19-11 (+B2) or 2 (IGCT NO. 4 fuse terminal) - Body ground and other terminals Ignition switch off 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A18-10 (+B), A18-11 (+B2) or 2 (IGCT NO. 4 fuse terminal) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


b.

Install the IGCT NO. 4 fuse.



OK

20.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

21.REPAIR OR REPLACE HARNESS OR CONNECTOR
20.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NEXT

REPLACE FUSE (IGCT NO. 4)

21.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (IGCT NO. 4)