Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › 2014.12–2015.11
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0277909 SFI SYSTEM C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM  P3190  Poor Engine Power  P3191  Engine does not Start  P3193  Fuel Run Out  


DESCRIPTION

From the hybrid vehicle control ECU, the ECM receives data such as engine power output required (required output), estimated torque produced by the engine (estimated torque), engine speed target (target speed), and whether the engine is in start mode or not. Then, based on the required output and target speed, the ECM calculates a target torque that is to be produced by the engine and compares it with the estimated torque. If the estimated torque is very low compared with the target torque, or the engine start mode continues for the specific duration calculated by the coolant temperature, an abnormal condition is detected.

DTC No. DTC Detection Condition Trouble Area
P3190 Following conditions continue at a fixed engine speed or a fixed length of time (1 trip detection logic):
·

Communication with hybrid vehicle control ECU is normal

·

Engine speed is a fixed value or more

·

Engine start mode is not active

·

Target torque is a fixed value

·

Ratio of estimated torque against target torque is less than 20%


·

Intake system

·

Throttle body with motor assembly

·

Fuel system

·

Engine

·

Mass air flow meter sub-assembly

·

Out of fuel

·

Engine coolant temperature sensor

·

Crank position sensor

·

Cam position sensor

·

EGR valve assembly

·

ECM


P3191 Following conditions continue at a fixed engine speed or a fixed length of time (1 trip detection logic):
·

Communication with hybrid vehicle control ECU is normal

·

Engine speed is a fixed value or more

·

Engine start mode is active

·

No engine start determination for 100 engine revolutions or more, and 6 seconds or more


·

Intake system

·

Throttle body with motor assembly

·

Fuel system

·

Engine

·

Mass air flow meter sub-assembly

·

Out of fuel

·

Engine coolant temperature sensor

·

Crank position sensor

·

Cam position sensor

·

EGR valve assembly

·

ECM


P3193 Fuel low level signal input into ECM (1 trip detection logic).
·

Out of fuel

·

ECM



MONITOR DESCRIPTION

The ECM and hybrid vehicle control ECU are connected using CAN communication. The ECM sends engine speed data and other data to the hybrid vehicle control ECU while the hybrid vehicle control ECU sends information such as a requirement for engine power to the ECM using CAN communication. When the communication between the ECM and hybrid vehicle control ECU is normal and the following items meet the specified conditions, the ECM stores a DTC.

1.

Engine speed

2.

Target torque

3.

Ratio of target torque against estimated torque

4.

Fuel level


MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the power switch on (IG) and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the tester on.

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine.

8.

Allow the engine to idle for 10 seconds or more.

9.

Enter the following menus: Powertrain / Engine and ECT / DTC.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P3190, P3191 or P3193.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

HINT:
·

Repeating this inspection for symptom confirmation may cause the SOC to drop, preventing the system from entering the READY-on state. In this case, use the THS charger to charge the HV battery.

·

Cranking the engine once causes the SOC to drop approximately 1%.

·

Charging the HV battery once (10 minutes) using the THS charger restores the SOC approximately 2%.

·

Charging the HV battery using the THS charger takes approximately 10 minutes when the HV battery temperature is 25°C (77°F) or approximately 30 minutes when the HV battery temperature is 0°C (32°F).

·

The THS charger is a supplemental charging device that charges the HV battery enough to enable the engine to start (the vehicle can enter the READY-on state).

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P3190, P3191 AND/OR P3193)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.

Result
Result Proceed to
DTC P3190, P3191 and/or P3193 are output A
DTC P3190, P3191 and/or P3193 and other DTCs are output B

HINT:

If any other codes besides P3190, P3191 and/or P3193 are output, perform troubleshooting for those DTCs first.




A

2.CHECK SHORTAGE OF FUEL

B

2.CHECK SHORTAGE OF FUEL
a.

Check the amount of fuel remaining.

OK:

There is enough fuel.


HINT:
·

DTCs P3190, P3191 and/or P3193 may be output if the vehicle run out of fuel in the past.

·

When an insufficient amount of fuel is added to the vehicle and when the hybrid control system will not engine because the DTCs P3190, P3191 and/or P3193 that are output regard the vehicle as out of fuel, continue refueling the vehicle until the fuel level warning light turns off.





OK

3.CHECK INTAKE SYSTEM

NG

REFILL FUEL

3.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks (See page Engine / Hybrid System>1NZ-FXE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leaks in intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).




OK

4.CHECK FOR UNUSUAL NOISE OR VIBRATION WHEN STARTING ENGINE OR REVVING UP

NG

REPAIR OR REPLACE INTAKE SYSTEM

4.CHECK FOR UNUSUAL NOISE OR VIBRATION WHEN STARTING ENGINE OR REVVING UP
OK:

Unusual noise and vibration do not occur.



OK

5.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE MALFUNCTIONING PART

5.CHECK FUEL PRESSURE

OK

6.INSPECT FREEZE FRAME DATA

NG

6.INSPECT FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC / Freeze Frame Data.


e.

Calculate the requested torque* and compare it with Actual Engine Torque.

HINT:

*: The requested torque is calculated by putting "Requested Engine Torque" and "HV Target Engine Speed" from the freeze frame data into the following formula:

Requested torque = Requested Engine Torque (kW) / HV Target Engine Speed (rpm) x 9554


Standard:

Actual Engine Torque is 60% or more of the request torque.


Result
Result Proceed to
NG A
OK B



A

7.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY

B

8.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
7.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY
a.

Inspect the throttle body with motor assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>THROTTLE BODY>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).




OK

8.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

8.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
a.

Inspect the mass air flow meter sub-assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).




OK

9.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

NG

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

9.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the engine coolant temperature sensor (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).




OK

10.INSPECT CRANK POSITION SENSOR

NG

10.INSPECT CRANK POSITION SENSOR

OK

11.REPLACE CAM POSITION SENSOR

NG

11.REPLACE CAM POSITION SENSOR

NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P3190, P3191 AND/OR P3193)
12.CHECK WHETHER DTC OUTPUT RECURS (DTC P3190, P3191 AND/OR P3193)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG) and turn the tester on.


g.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


h.

Start the engine.


i.

Allow the engine to idle for 10 seconds or more.


j.

Enter the following menus: Powertrain / Engine and ECT / DTC.


k.

Read the pending DTCs.

Result
Result Proceed to
DTC P3190, P3191 and/or P3193 is output A
DTC is not output B



A

13.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE EGR STEP POSITION)

B

END

13.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE EGR STEP POSITION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Data List / All Data / Throttle Idle Position and MAP.


g.

Confirm that the Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.

NOTICE:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

MAP change in response to EGR step position when Throttle Idle Position is ON in Data List.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
MAP
(Data List)
(EGR valve is fully closed) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:
·

While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.

·

If there are starting problems and the Active Test cannot be performed, perform the EGR valve assembly inspection in the next step.



Result:
Result Proceed to
Outside of standard range A
Within standard range B




A

14.INSPECT EGR VALVE ASSEMBLY

B

15.REPLACE ECM
14.INSPECT EGR VALVE ASSEMBLY
a.

Remove the EGR valve assembly (See page Engine / Hybrid System>1NZ-FXE EMISSION CONTROL>EGR VALVE>REMOVAL).


b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).




OK

15.REPLACE ECM

NG

15.REPLACE ECM

NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG) and turn the tester on.


g.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


h.

Start the engine.


i.

Allow the engine to idle for 10 seconds or more.


j.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


k.

Input the DTC: P3190, P3191 or P3193.


l.

Check the DTC judgment result.



NEXT

END