G3834
1.REMOVE SERVICE PLUG GRIP
2.PLACE FRONT WHEELS FACING STRAIGHT AHEAD
3.REMOVE FRONT WHEELS
4.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY (Integrated Cover Type)
51442C
5.REMOVE ENGINE UNDER COVER LH (Separated Cover Type)
51441C
6.REMOVE ENGINE UNDER COVER RH (Separated Cover Type)
7.DRAIN COOLANT (for Engine)
8.DRAIN COOLANT (for Inverter)
9.DRAIN HYBRID TRANSAXLE FLUID
53301
10.REMOVE HOOD SUB-ASSEMBLY
Remove the 4 bolts and hood sub-assembly from the hood hinge assembly LH and hood hinge assembly RH.
11.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
55722C
12.REMOVE INNER COWL TOP TO COWL BRACE (for LHD)
55722C
13.REMOVE INNER COWL TOP TO COWL BRACE (for RHD)
55735B
14.REMOVE FRONT AIR SHUTTER SEAL (for LHD)
55735B
15.REMOVE FRONT AIR SHUTTER SEAL (for RHD)
55815E
16.REMOVE FRONT NO. 1 VENTILATOR SEAL (for LHD)
55815E
17.REMOVE FRONT NO. 1 VENTILATOR SEAL (for RHD)
55701J
18.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)
55701J
19.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
G9200
20.REMOVE INVERTER WITH CONVERTER ASSEMBLY
G9110
21.REMOVE INVERTER BRACKET ASSEMBLY
33820B
22.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
| *1 | Transmission Control Cable Clamp |
| *2 | Transmission Control Cable Support |
Remove the nut, clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket and transmission control shaft lever.
Disconnect the transmission control cable assembly from the transmission control cable clamp and transmission control cable support.
23.DISCONNECT WIRE HARNESS
Disconnect the 4 clamps and No. 2 engine wire.
Remove the 3 bolts and disconnect the 4 connectors, 7 clamps and wire harness from the hybrid vehicle transaxle assembly.
24.SECURE STEERING WHEEL
45259A
25.REMOVE COLUMN HOLE COVER SILENCER SHEET
45209
26.SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY
45025D
27.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
17410
28.REMOVE FRONT EXHAUST PIPE ASSEMBLY
29.REMOVE FRONT DRIVE SHAFT ASSEMBLY
25612
30.REMOVE NO. 2 EGR PIPE
25620
31.REMOVE EGR VALVE ASSEMBLY
12281A
32.INSTALL NO. 1 ENGINE HANGER
33.SUSPEND ENGINE ASSEMBLY
Attach the sling device to the engine hangers and chain block.
51201
34.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
12364A
35.REMOVE ENGINE LATERAL CONTROL ROD
Remove the 4 bolts and engine lateral control rod from the hybrid vehicle transaxle assembly.
30900
36.SUPPORT HYBRID VEHICLE TRANSAXLE ASSEMBLY
Support the hybrid vehicle transaxle assembly with a transmission jack.
12325A
37.REMOVE ENGINE MOUNTING BRACKET LH
Remove the through bolt, nut and disconnect the engine mounting insulator LH from the engine mounting bracket LH.
Remove the 4 bolts and engine mounting bracket LH from the hybrid vehicle transaxle assembly.
30900
38.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY
| *1 | Wire Harness Clamp Bracket |
| *2 | Transmission Control Cable Clamp |
Remove the 3 bolts, 2 wire harness clamp brackets and transmission control cable clamp from the hybrid vehicle transaxle assembly.
Remove the bolt, nut and drive shaft heat insulator sub-assembly from the engine and drive shaft heat insulator bracket.
Disconnect the clamp from the drive shaft heat insulator bracket.
Remove the 2 bolts and drive shaft heat insulator bracket from the engine.
Remove the 2 bolts and starter hole heat insulator from the engine.
Disengage the claw and remove the flywheel housing side cover from the engine.
Remove the 6 bolts and hybrid vehicle transaxle assembly.
To avoid damage to the knock pins, do not pry between the hybrid vehicle transaxle assembly and the engine.
To prevent the splines of the damper from becoming misaligned, do not allow the transaxle to hit the damper during transaxle removal and installation.
G1250
39.REMOVE MOTOR COOLING PIPE ASSEMBLY
Remove the bolt and oil cooler tube clamp from the No. 1 transmission control cable bracket.
| *1 | Flare Nut |
| *2 | Union |
| *3 | Union Bolt |
Using a union nut wrench, disconnect the motor cooling pipe assembly from the union.
Turn the flare nut while holding the union.
Remove the union bolt, gasket and motor cooling pipe assembly from the hybrid vehicle transaxle assembly.
Remove the union and O-ring from the hybrid vehicle transaxle assembly.
G1148
40.REMOVE MOTOR CABLE
33823
41.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET
Remove the 2 bolts and No. 1 transmission control cable bracket from the hybrid vehicle transaxle assembly.
35572D
42.REMOVE TRANSMISSION CONTROL SHAFT LEVER
Remove the nut, washer, and transmission control shaft lever from the manual valve shaft.
89451A
43.REMOVE SHIFT LEVER POSITION SENSOR
Perform this procedure only when replacement of the automatic transmission case cover is necessary.
| *1 | Lock Plate |
Using a screwdriver, pry the tabs of the lock plate.
| *1 | Lock Nut |
| *2 | Lock Plate |
Remove the lock nut and lock plate from the manual valve shaft.
Remove the 2 bolts and pull out the shift lever position sensor from the manual valve shaft.
35151J
44.REMOVE AUTOMATIC TRANSMISSION CASE COVER
Perform this procedure only when replacement of the automatic transmission case cover is necessary.
Remove the 2 bolts and automatic transmission case cover from the hybrid vehicle transaxle assembly.
G1143
45.REMOVE MOTOR CABLE BRACKET
Remove the bolt and motor cable bracket from the transmission control cable support.
33829
46.REMOVE TRANSMISSION CONTROL CABLE SUPPORT
Remove the 3 bolts and 2 transmission control cable supports from the hybrid vehicle transaxle assembly.
47.REMOVE WIRE HARNESS CLAMP BRACKET
Remove the bolt and wire harness clamp bracket from the hybrid vehicle transaxle assembly.
30900H
48.REMOVE TRANSAXLE HSG AND CASE WITH HEAD STRAIGHT SCREW PLUG
Remove the transaxle HSG and case with head straight screw plug and gasket from the hybrid vehicle transaxle assembly.