Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE CARRIER
RM3210E _52 Drivetrain _047518 AXLE AND DIFFERENTIAL _0244652 REAR AXLE CARRIER A

AXLE AND DIFFERENTIAL  REAR AXLE CARRIER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle carrier sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: for LH Side

Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system
Simple intelligent parking assist system
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Rear wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Intelligent clearance sonar system

·

Simple intelligent parking assist system


(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Rear height control sensor sub-assembly LH*1

·

Suspension, tires, etc.

(The vehicle height changes because of suspension or tire replacement)


Initialize No. 1 headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)

NOTICE:
·

When removing or installing the rear disc brake caliper assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C1214 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this step.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISABLE BRAKE CONTROL

Hide 3.REMOVE REAR WHEEL

Hide 57628C 4.REMOVE REAR FLOOR SIDE MEMBER COVER LH (for LH Side)

Hide 58390 5.REMOVE NO. 1 FLOOR UNDER COVER ASSEMBLY (for RH Side)

Hide 46441 6.LOOSEN NO. 1 WIRE ADJUSTING NUT

Hide 47658B 7.REMOVE PARKING BRAKE LEVER PROTECTOR

Hide 46430 8.SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY

Hide 9.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

Hide 42431 10.REMOVE REAR DISC

Hide 89516D 11.DISCONNECT SKID CONTROL SENSOR WIRE

Hide 42450B 12.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY

Hide 13.REMOVE FLEXIBLE HOSE BRACKET

a.
C345068

Remove the bolt and flexible hose bracket from the rear axle carrier sub-assembly.


Hide 89408C 14.REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (for LH Side)

Hide 48840A 15.REMOVE REAR STABILIZER LINK ASSEMBLY

Hide 48231B 16.REMOVE REAR COIL SPRING

Hide 48258C 17.REMOVE REAR LOWER COIL SPRING INSULATOR

Hide 48720A 18.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY

Hide 42305 19.REMOVE REAR AXLE CARRIER SUB-ASSEMBLY

a.
C348732

Loosen the 2 bolts of the rear trailing arm assembly.


b.
C348733C02
0.969,0.615 1.135,0.615 1.135,0.615 1.313,0.833 true 0.708,0.542 0.958,0.74 0.25,0.198 10 true *1
*1 Rear Axle Carrier Pin


Loosen the nut of the rear shock absorber assembly.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.



c.
C345052C02
1.396,2.427 1.958,2.427 false 1.49,3.146 1.99,3.146 false 1.208,2.344 1.521,2.5 0.313,0.156 10 false *a 1.302,3.063 1.615,3.219 0.313,0.156 10 false *b
*a Wooden Block
*b Jack


Using a jack and a wooden block, support the rear axle carrier sub-assembly.

NOTICE:
·

When jacking up the rear axle carrier sub-assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.




d.
C345053N01
1.042,0.448 1.198,0.646 0.156,0.198 10 true A

Loosen the bolt (A).

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



e.

Remove the 2 bolts and separate the rear trailing arm assembly from the rear axle carrier sub-assembly.


f.

Remove the nut and separate the rear shock absorber assembly from the rear axle carrier sub-assembly.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.



g.

Remove the bolt (A), nut and rear axle carrier sub-assembly from the rear upper control arm assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.