Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER
RM30B0U _53 Suspension _009475 REAR SUSPENSION _0051214 REAR SUSPENSION MEMBER A

REAR SUSPENSION  REAR SUSPENSION MEMBER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL REAR NO. 1 DIFFERENTIAL MOUNT CUSHION (for AWD)

Hide 2.INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.
C266838
1.229,0.531 1.01,0.531 false 1.01,0.531 1.01,0.885 true 2.469,0.885 2.469,0.542 true 2.469,0.531 2.219,0.531 false 2.583,1.927 2.354,1.927 true 2.354,1.927 2.354,1.76 true 1.063,1.75 1.063,1.917 true 1.063,1.917 0.854,1.917 true 1.26,0.448 1.646,0.667 0.385,0.219 10 *a 2.073,0.438 2.458,0.656 0.385,0.219 10 *a 0.688,1.823 1.073,2.042 0.385,0.219 10 *a 2.635,1.844 3.021,2.063 0.385,0.219 10 *a
*a Attachment Placement Positions


Place wooden blocks or plate lift attachments on an engine lifter, and then set the rear suspension member sub-assembly so that the attachments are in the positions shown in the illustration.

NOTICE:
·

Place the wooden blocks or plate lift attachments so that the rear suspension member sub-assembly is level.

·

As the rear suspension member sub-assembly is very heavy, be sure to support it securely.




b.
C266837

Install the rear suspension member and 2 rear upper body mounting cushions with the 2 bolts and 2 nuts.

Torque:
125 N*m (1275 kgf*cm, 92 ft.*lbf)


Hide 3.INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY (for AWD)

Hide 4.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for AWD)

Hide 5.TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH

a.

Temporarily install the upper control arm to the rear suspension member with the bolt and nut.


Hide 6.TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 7.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 8.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 9.INSTALL REAR LOWER COIL SPRING INSULATOR LH

Hide 10.INSTALL REAR LOWER COIL SPRING INSULATOR RH

HINT:

Use the same procedure described for the LH side.


Hide 11.INSTALL REAR UPPER COIL SPRING INSULATOR LH

Hide 12.INSTALL REAR UPPER COIL SPRING INSULATOR RH

HINT:

Use the same procedure described for the LH side.


Hide 13.INSTALL REAR COIL SPRING LH

Hide 14.INSTALL REAR COIL SPRING RH

HINT:

Use the same procedure described for the LH side.


Hide 15.TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY LH

Hide 16.TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 17.INSTALL REAR AXLE CARRIER SUB-ASSEMBLY LH

a.

Install the rear axle carrier to the rear upper control arm with the bolt and nut.

Torque:
90 N*m (918 kgf*cm, 66 ft.*lbf)

NOTICE:

Since a stopper nut is used, tighten the bolt.



Hide 18.INSTALL REAR AXLE CARRIER SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 19.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 20.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 21.CONNECT REAR TRAILING ARM ASSEMBLY LH

a.

Connect the rear trailing arm to the rear axle carrier with the 2 bolts.

Torque:
200 N*m (2039 kgf*cm, 148 ft.*lbf)


Hide 22.CONNECT REAR TRAILING ARM ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 23.INSTALL REAR STABILIZER BAR

Hide 24.INSTALL REAR STABILIZER LINK ASSEMBLY LH

Hide 25.INSTALL REAR STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 26.INSTALL REAR SUSPENSION MEMBER BRACE LH

Hide 27.INSTALL REAR SUSPENSION MEMBER BRACE RH

HINT:

Use the same procedure described for the LH side.


Hide 28.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH (for 2WD)

Hide 29.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY RH (for 2WD)

HINT:

Use the same procedure described for the LH side.


Hide 30.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH (for AWD)

Hide 31.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY RH (for AWD)

HINT:

Use the same procedure described for the LH side.


Hide 32.INSTALL PARKING BRAKE ASSEMBLY

Hide 33.INSTALL REAR DISC

Hide 34.CONNECT REAR DISC BRAKE CALIPER ASSEMBLY LH

Hide 35.CONNECT REAR DISC BRAKE CALIPER ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 36.CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

Hide 37.CONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT:

Use the same procedure described for the No. 3 parking brake cable assembly.


Hide 38.CONNECT SKID CONTROL SENSOR WIRE LH (for 2WD)

Hide 39.CONNECT SKID CONTROL SENSOR WIRE RH (for 2WD)

HINT:

Use the same procedure described for the LH side.


Hide 41.CONNECT REAR SPEED SENSOR RH (for AWD)

HINT:

Use the same procedure described for the LH side.


Hide 42.INSTALL REAR AXLE SHAFT NUT LH (for AWD)

Hide 43.INSTALL REAR AXLE SHAFT NUT RH (for AWD)

HINT:

Use the same procedure described for the LH side.


Hide 45.TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH

Hide 46.TIGHTEN REAR SHOCK ABSORBER ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 47.TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY LH

Hide 48.TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 49.TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 50.TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 51.TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 52.TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 53.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 54.INSPECT AND ADJUST REAR WHEEL ALIGNMENT