Home › Engine / Hybrid System › 2WW ENGINE MECHANICAL › ENGINE UNIT › from 2015.10
RM3090E _51 Engine / Hybrid System _044373 2WW ENGINE MECHANICAL _0211289 ENGINE UNIT A

2WW ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Always be sure to check the tightening torque.

·

If the pressure lines are leaking after installation, they must be replaced.

·

Do not overtighten the pressure lines.

·

All pressure lines may only be reused 3 times. After the 3rd time, they must be replaced.



PROCEDURE

Hide 43457 1.INSTALL DRIVE SHAFT BEARING BRACKET

a.
A347058N01
1.24,0.042 1.396,0.24 0.156,0.198 10 true A 2.208,0.99 2.365,1.188 0.156,0.198 10 true B 0.656,0.813 0.813,1.01 0.156,0.198 10 true C

Using a T50 "TORX" socket wrench, install the drive shaft bearing bracket with the 3 bolts.

Torque:
63.7 N*m (650 kgf*cm, 47 ft.*lbf)

NOTICE:
·

Temporarily install the bolt (A), and then tighten the 3 bolts in the order of (B), (A) and (C).

·

Make sure that the bolts and bolt holes are free of oil. Clean them if necessary.




Hide 19850 4.INSTALL GLOW PLUG ASSEMBLY

Hide 23810A 5.INSTALL COMMON RAIL ASSEMBLY

Hide 6.INSTALL INJECTION PIPE SUB-ASSEMBLY

Hide 7.INSTALL FUEL INLET PIPE SUB-ASSEMBLY

Hide 12281A 8.INSTALL NO. 1 ENGINE HANGER

a.

Install the No. 1 engine hanger to the cylinder head sub-assembly with the bolt.

HINT:

Refer to "SPECIFICATIONS - STANDARD BOLT" for the tightening torque.



Hide 12282D 9.INSTALL NO. 2 ENGINE HANGER

a.

Install the No. 2 engine hanger to the cylinder head sub-assembly with the 2 bolts.

HINT:

Refer to "SPECIFICATIONS - STANDARD BOLT" for the tightening torque.



Hide 10.INSTALL EGR VALVE BRACKET

a.

Install the EGR valve bracket to the cylinder head sub-assembly with the 2 bolts.

HINT:

Refer to "SPECIFICATIONS - STANDARD BOLT" for the tightening torque.



Hide 17293 11.INSTALL TURBOCHARGER STAY

a.

Install the turbocharger stay with the 2 bolts.

HINT:

Refer to "SPECIFICATIONS - STANDARD BOLT" for the tightening torque.



Hide 17271 12.INSTALL NO. 2 TURBO INSULATOR

a.

Install the No. 2 turbo insulator with the 3 bolts.

HINT:

Refer to "SPECIFICATIONS - STANDARD BOLT" for the tightening torque.



Hide 15481 13.INSTALL NO. 1 TURBO OIL PIPE

a.

Install the No. 1 turbo oil pipe, 2 nuts and 2 new gaskets with the union bolt.

Torque:
Union bolt : 35 N*m (357 kgf*cm, 26 ft.*lbf)

HINT:

Refer to "SPECIFICATIONS - STANDARD BOLT" for the tightening torque.



Hide 25680 15.INSTALL EGR COOLER ASSEMBLY WITH EGR VALVE ASSEMBLY

Hide 25051 19.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Hide 20.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 23801Q 21.INSTALL FUEL FEED PIPE SUB-ASSEMBLY

a.

Install the fuel feed pipe sub-assembly with the 2 bolts.

HINT:

Refer to "SPECIFICATIONS - STANDARD BOLT" for the tightening torque.



b.

Connect the 2 fuel hoses to the fuel supply pump assembly, and tighten the 2 clamps to secure the 2 hoses.


c.

Connect the fuel return tube to the common rail assembly.


d.

Attach the fuel hose clamp.


e.

Connect the nozzle leakage pipe assembly to the fuel feed pipe sub-assembly.


Hide 25733A 23.INSTALL NO. 1 VACUUM PIPE

Hide 24.INSTALL NO. 2 VACUUM HOSE ASSEMBLY

a.

Install the No. 2 vacuum hose assembly to the No. 2 engine hanger with the bolt and nut.

Torque:
: 8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 25.CONNECT NO. 2 VACUUM HOSE ASSEMBLY

Hide 11459 26.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 22030 27.INSTALL DIESEL THROTTLE BODY ASSEMBLY

Hide 16620 28.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

a.

Install the V-ribbed belt tensioner assembly with the 2 bolts.

Torque:
: 20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 12315A 29.INSTALL ENGINE MOUNTING BRACKET

a.

Install the 2 stud bolts to the engine mounting bracket.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Using an E12 "TORX" socket wrench, install the engine mounting bracket with the 3 bolts.

Torque:
: 59 N*m (602 kgf*cm, 44 ft.*lbf)


Hide 16630G 30.INSTALL IDLER PULLEY ASSEMBLY

a.

Using a T50 "TORX" socket wrench, tighten the bolt to install the idler pulley assembly.

Torque:
: 40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 27020 31.INSTALL GENERATOR ASSEMBLY

Hide 88310 32.INSTALL COMPRESSOR ASSEMBLY WITH PULLEY (w/ Air Conditioning System)

Hide 34.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine assembly.


Hide 12612A 35.INSTALL ENGINE COVER