Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › from 2016.08
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0148247 NAVIGATION SYSTEM(for Radio and Display Type) T

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  PROBLEM SYMPTOMS TABLE  


HINT:
·

Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.

·

Inspect the fuses and relays related to this system before inspecting the suspected areas below.



Display Function
Symptom Suspected Area Link
Pressing power switch does not turn on system. Proceed to "Radio Receiver Power Source Circuit" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Black screen (No image appears on navigation/audio screen). Proceed to "Black Screen" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Display does not dim (does not change to night screen) with tail switch on. Proceed to "Display does not Dim when Light Control Switch is Turned ON" Click here
Proceed to "Illumination Circuit" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Power does not turn off (Screen remains on). Proceed to "Radio Receiver Power Source Circuit" Click here
Radio and display receiver assembly Click here
Screen is distorted. Proceed to "Radio Receiver Power Source Circuit" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Screen flicker or color distortion. Proceed to "Screen Flicker or Color Distortion" Click here
Proceed to "Radio Receiver Power Source Circuit" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Navigation function switches can be operated while vehicle being driven. Proceed to "Parking Brake Switch Circuit" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here

Panel Switch and Touch Switch Function
Symptom Suspected Area Link
Illumination for panel switches does not come on with tail switch on. Proceed to "Illumination for Panel Switch does not Come on with Tail Switch ON" Click here
Proceed to "Illumination Circuit" Click here
Radio and display receiver assembly Click here
Panel switches do not function. Proceed to "Panel Switches do not Function" Click here
Proceed to "Radio Receiver Power Source Circuit" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Touch panel switch does not function. Proceed to "Touch Panel Switch does not Function" Click here
Proceed to "Radio Receiver Power Source Circuit" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Navigation function switches can be operated while vehicle is driving. Proceed to "Parking Brake Switch Circuit" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here

Steering Pad Switch Function
Symptom Suspected Area Link
System cannot be operated by steering pad switch. Proceed to "Panel Switches do not Function" Click here
Proceed to "Steering Pad Switch Circuit" Click here
Radio and display receiver assembly Click here
Illumination for steering pad switch does not come on with tail switch on. Proceed to "Illumination Circuit" Click here
Radio and display receiver assembly Click here

Navigation Function
Symptom Suspected Area Link
Date and time on navigation screen are different from actual date and time. Proceed to "Vehicle Position Mark Deviates Greatly" Click here
Proceed to "Vehicle Speed Signal Circuit between Radio Receiver and Extension Module" Click here
Proceed to "Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter" Click here
Navigation antenna assembly*1 Click here
No. 1 amplifier antenna assembly*2 Click here
Antenna divider*3 Click here
Navigation ECU Click here
Vehicle position mark moves slow or fast. Proceed to "Vehicle Position Mark Deviates Greatly" Click here
Drive the vehicle for sensor learning (at a place where GPS signals can be received, drive the vehicle clockwise and counterclockwise in at least a 200 meter square 2 times or more) -
Proceed to "Vehicle Speed Signal Circuit between Radio Receiver and Extension Module" Click here
Proceed to "Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter" Click here
Navigation antenna assembly*1 Click here
No. 1 amplifier antenna assembly*2 Click here
Antenna divider*3 Click here
Navigation ECU Click here
Vehicle position mark deviates from correct position and does not return to correct position. Proceed to "Vehicle Position Mark Deviates Greatly" Click here
Proceed to "Vehicle Speed Signal Circuit between Radio Receiver and Extension Module" Click here
Proceed to "Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter" Click here
Navigation antenna assembly*1 Click here
No. 1 amplifier antenna assembly*2 Click here
Antenna divider*3 Click here
Navigation ECU Click here
Vehicle position mark is not updated. Proceed to "Vehicle Speed Signal Circuit between Radio Receiver and Extension Module" Click here
Proceed to "Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter" Click here
Navigation antenna assembly*1 Click here
No. 1 amplifier antenna assembly*2 Click here
Antenna divider*3
Navigation ECU Click here
Cursor or map rotates when vehicle is stopped. Proceed to "Cursor or Map Rotates when Vehicle Stopped" Click here
Navigation ECU Click here
Vehicle position mark moves in the opposite direction to the vehicle. Proceed to "Cursor or Map Rotates when Vehicle Stopped" Click here
Navigation ECU Click here
Map display is incomplete. Proceed to "Map Display Incomplete" Click here
Navigation ECU Click here
Route cannot be calculated. Proceed to "Route cannot be Calculated" Click here
Navigation ECU Click here
Traffic information is not displayed on navigation screen. Proceed to "Radio Broadcast cannot be Received or Poor Reception" Click here
Navigation system cannot record memory point registration or each item setting. Navigation ECU Click here
A message is displayed because map data cannot be read, and current position screen is not displayed. If a message appears only when driving on rough roads, check if the message disappears when vehicle is stopped -
Navigation ECU Click here
Map screen turns white or blue (GPS receiving status is displayed normally, and switches and own vehicle position mark are also displayed normally). Change map scale to the smallest (a scale that shows a large area) -
Navigation ECU Click here
Customize parameters cannot be changed (customize parameters can be changed by using the GTS). Navigation ECU Click here
Reverse signal does not change in vehicle signal check mode. Proceed to "Reverse Signal Circuit" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Parking brake switch signal does not change in vehicle signal check mode. Proceed to "Parking Brake Switch Circuit" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Voice guidance does not function. Proceed to "Voice Guidance does not Function" Click here
Proceed to "Mute Signal Circuit between Radio Receiver and Telematics Transceiver"*3 Click here
Proceed to "Speaker Circuit" Click here
Telematics transceiver*3 Click here
Navigation ECU Click here
Radio and display receiver assembly Click here

*1: Except models with the vehicle identification number on the certification label ending with the character X.

*2: Only for models with the vehicle identification number on the certification label ending with the character X.

*3: w/ Telematics Transceiver


General Audio Function
Symptom Suspected Area Link
No sound can be heard from speakers. Proceed to "No Sound can be Heard from Speakers" Click here
Proceed to "Mute Signal Circuit between Radio Receiver and Telematics Transceiver"* Click here
Proceed to "Speaker circuit" Click here
Telematics transceiver* Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Abnormal noise occurs. Proceed to "Noise Occurs" Click here
Proceed to "Mute Signal Circuit between Radio Receiver and Telematics Transceiver"* Click here
Telematics transceiver* Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Sound quality is bad in all modes (Volume is too low). Check that the ASL function is off -
Proceed to "Poor Sound Quality in All Modes (Low Volume)" Click here
Proceed to "Mute Signal Circuit between Radio Receiver and Telematics Transceiver"* Click here
Proceed to "Speaker circuit" Click here
Telematics transceiver* Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
ASL does not function. Check that the ASL function is on -
Proceed to "Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter" Click here
Telematics transceiver* Click here
Navigation ECU Click here
Radio and display receiver assembly Click here

*: w/ Telematics Transceiver


FM or AM Radio Function
Symptom Suspected Area Link
Radio broadcast cannot be received or poor reception. Proceed to "Radio Broadcast cannot be Received or Poor Reception" Click here
Radio broadcast can be received but radio station cannot be displayed (Some radio stations do not provide their name information). Navigation ECU Click here
Radio and display receiver assembly Click here
Radio broadcast can be displayed but radio broadcast cannot be heard from speakers. Check the volume settings -
Navigation ECU Click here
Radio and display receiver assembly Click here

Digital Audio Broadcast (DAB) Function (w/ DAB Function)
Symptom Suspected Area Link
Sound cannot be heard/sound quality is poor/loud noise occurs only when DAB function is used (when receiving DAB-TA, sound temporarily may not be heard). Operate the volume switch and turn up the volume level -
Proceed to "Check DAB Reception" in Operation Check Click here
Windshield glass (DAB antenna) Click here
Digital audio broadcasting antenna assembly Click here
No. 4 antenna cord sub-assembly Click here
No. 2 antenna cord sub-assembly Click here
Antenna cord sub-assembly Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
When time shift mode is not selected, DAB-TA cannot be used. Check if DAB-TA function is set to on -
Check that "TP" icon is displayed on the screen -
Check if similar symptoms occur with another vehicle -
Navigation ECU Click here
Radio and display receiver assembly Click here
DAB-DAB Link, DAB-FM Link or Time- Shift cannot be used. Check if each function is set to on -
Check if similar symptoms occur when receiving other broadcasts -
Navigation ECU Click here
Radio and display receiver assembly Click here

CD Player Function (for 6.1 Inch Display)
Symptom Suspected Area Link
Disc cannot be played or player does not function with disc. Proceed to "Disc Player Outline" in System Description and check if the disc is compatible with the disc player Click here
Proceed to "Check Optical Disc Error History" in Operation Check Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Disc cannot be inserted/played or disc is ejected right after insertion. Proceed to "Check Optical Disc Error History" in Operation Check Click here
Proceed to "Disc cannot be Inserted or is Ejected Right After Insertion" Click here
Disc cannot be ejected. Proceed to "Check Optical Disc Error History" in Operation Check Click here
Proceed to "Disc cannot be Ejected" Click here
Disc sound skips. Proceed to "Check Optical Disc Error History" in Operation Check Click here
Proceed to "CD Sound Skips" Click here
Sound quality is bad only when disc is played (volume is too low). Proceed to "Check Optical Disc Error History" in Operation Check Click here
Proceed to "Sound Quality is Bad Only when Disc is Played (Volume is Too Low)" Click here
Album cover art cannot be displayed.* Check that display cover art on the disc settings screen is set to on -
Check if similar symptoms occur with another vehicle -
If an indication to update the Gracenote database appears on the album cover art screen and update data has been downloaded to the radio and display receiver assembly, update the Gracenote database to the latest version -
Navigation ECU Click here
Radio and display receiver assembly Click here

*: w/ Connected Services


AUX (Stereo Jack) Function
Symptom Suspected Area Link
External device sound cannot be heard or sound quality is bad (Stereo jack is used). Proceed to "Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter" Click here
No. 1 stereo jack adapter assembly Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
"AUX/VTR" is not displayed on system check mode screen. Proceed to "Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter" Click here
No. 1 stereo jack adapter assembly Click here
Navigation ECU Click here
Radio and display receiver assembly Click here

"Bluetooth" Hands-free Function
Symptom Suspected Area Link
"Bluetooth" is inoperative (In-vehicle device cannot be recognized by the cellular phone). Proceed to "Cellular Phone Inspection" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
"Bluetooth" compatible cellular phone cannot be registered. Proceed to "Cellular Phone Registration Failure" Click here
"Bluetooth" compatible cellular phone cannot be connected. Check that no other cellular phone is connected as a hands-free device -
Bring the cellular phone near the in-vehicle device and reconnect it -
Proceed to "Cellular Phone Inspection" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
"Bluetooth" compatible cellular phone cannot be connected automatically (can be connected manually). Check that "Bluetooth" automatic connection setting of the in-vehicle device is on -
Navigation ECU Click here
Radio and display receiver assembly Click here
"Bluetooth" compatible cellular phone connection is disconnected. Bring the cellular phone near the in-vehicle device and check if it is reconnected -
Proceed to "Cellular Phone Inspection" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Message that prompts to check the cellular phone is displayed. Bring the cellular phone near the in-vehicle device and check if it is reconnected -
Proceed to "Cellular Phone Inspection" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
When the ignition switch is turned to ACC, instructions for checking the connection condition between the in-vehicle device and cellular phone are displayed. Turn the cellular phone connection conformation display on the in-vehicle device off -
Phonebook data cannot be transferred. Check that the phonebook automatic transfer setting of the in-vehicle device is on -
Enter "1234" into the "Bluetooth" phone (when transferring phonebook data, OBEX authentication may be required) -
Check that no applications on the cellular phone are running -
If using "Bluetooth" audio function, cancel the "Bluetooth" audio player connection and check the operation -
Transfer phonebook data manually -
Proceed to "Cellular Phone Inspection" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Phonebook data is cleared. Navigation ECU Click here
Radio and display receiver assembly Click here
Phonebook data cannot be edited. Check that the phonebook data automatic transfer setting is off -
Navigation ECU Click here
Radio and display receiver assembly Click here
All the transferred phonebook data is sorted to "Other". Check that no applications on the cellular phone are operating -
Check that phonebook data in the cellular phone is not stored to the SIM card -
Proceed to "Cellular Phone Inspection" Click here
Explain to the customer that all the transferred phonebook data may be stored to "Other" depending on cellular phone -
Cellular phone cannot make outgoing/ incoming calls. Move the vehicle into a cellular phone service area, check that the "Bluetooth" device is connected to the vehicle and operate device again -
Check that the cellular phone can make outgoing/incoming calls properly when not connected via "Bluetooth" -
Proceed to "Cellular Phone Inspection" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Other caller's voice is interrupted by noise or sound quality is poor. Check the receiving voice volume (if it is too high, voice may sound distorted) -
Make a call with the cellular phone disconnected from "Bluetooth" and check that other caller's voice can be heard clear -
Proceed to "Cellular Phone Inspection" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Other caller's voice cannot be heard. Check that reception voice volume is not set to minimum -
Make a call with the cellular phone disconnected from "Bluetooth" and check that other caller's voice can be heard clearly -
Proceed to "Cellular Phone Inspection" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Caller's voice (your voice) is interrupted by noise or sound quality is poor. Check the transmitting voice volume (if it is too high, voice may sound distorted) -
Check that nothing can cause noise around the microphone (an outlet of the air conditioning system facing the microphone, wind from an open window, additional devices, etc. may affect noise occurrence) -
Proceed to "Cellular Phone Inspection" Click here
Proceed to "Microphone Circuit between Radio Receiver and Extension Module" Click here
Proceed to "Microphone Circuit between Microphone and Radio Receiver" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Other caller cannot hear your voice. When talking on the cellular phone, check that the mute button is not pressed -
Check that nothing can cause noise around the microphone (an outlet of the air conditioning system facing the microphone, wind from an open window, additional devices, etc. may affect noise occurrence) -
Proceed to "Cellular Phone Inspection" Click here
Proceed to "Microphone Circuit between Radio Receiver and Extension Module" Click here
Proceed to "Microphone Circuit between Microphone and Radio Receiver" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
No notification when a new SMS/MMS/e-mail has been received. Check the SMS/MMS/e-mail notification settings on the cellular phone and the radio and display receiver assembly -
Proceed to "Cellular Phone Inspection" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Received SMS/MMS/e-mail cannot be read. Check the SMS/MMS/e-mail transfer settings on the cellular phone and the radio and display receiver assembly -
Proceed to "Cellular Phone Inspection" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
SMS/MMS/e-mail cannot be replied to. Move the vehicle into a cellular phone service area, and check the operation of the radio and display receiver assembly and cellular phone -
Check that the cellular phone can send an SMS/MMS/e-mail -
Proceed to "Cellular Phone Inspection" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here

"Bluetooth" Audio Function
Symptom Suspected Area Link
Portable player cannot be registered. Proceed to "Portable Player cannot be Registered" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Portable player cannot be connected manually/automatically. Proceed to "Portable Player cannot be Registered" Click here
Proceed to "Portable Player cannot be Connected Manually/Automatically" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Cellular phone with portable audio function cannot be recognized as "Bluetooth" audio device even when connected using "Bluetooth". Proceed to "Portable Player cannot be Registered" Click here
Proceed to "Portable Player cannot be Connected Manually/Automatically" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Sound of portable player cannot be heard from speakers, or sound is low. Proceed to "Sound of Portable Player cannot be Heard from Speakers or Sound is Low" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Portable player does not play even after "Bluetooth" audio mode is selected. Proceed to "Does not Play even after Bluetooth Audio Mode is Selected" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Portable player does not play. Proceed to "Does not Play even after Bluetooth Audio Mode is Selected" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Track information such as track number, track name, elapsed play time and playlist is not displayed. Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Operation switches for portable player such as play, pause, repeat, random and scan are not displayed. Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Battery condition of portable player is not displayed. Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
"Bluetooth" signal condition is not displayed. Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Portable player cannot pause, select file, fast forward, fast rewind, play at random or scan. Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Noise occurs or sound skips when portable player plays. Proceed to "Noise Occurs or Sound Skips when Portable Player Plays" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Registered device cannot be deleted. Proceed to "Registered Device cannot be Deleted" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here

"Wi-Fi" Function (w/ "Wi-Fi" Function)
Symptom Suspected Area Link
Cannot establish "Wi-Fi" connection. Proceed to "Cannot Establish Wi-Fi Connection" Click here

Voice Recognition Function (w/ Voice Recognition Function)
Symptom Suspected Area Link
Voice menu screen is not displayed (voice recognition function does not turn on). Check if the voice recognition prompt function is on -
Proceed to "Panel Switches do not Function" Click here
Proceed to "Steering Pad Switch Circuit" Click here
Radio and display receiver assembly Click here
When voice recognition switch is pressed, a short beep is emitted but voice cannot be recognized properly. Proceed to "Voice is not Recognized" Click here
Proceed to "Microphone Circuit between Microphone and Radio Receiver" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here

Mobile Assistant Function
Symptom Suspected Area Link
Mobile Assistant function does not work Confirm the Siri speech recognition application can be used on the device. -
Confirm a hard reset of the device does not correct the problem. -
Proceed to "Steering Pad Switch Circuit" Click here
Proceed to "Voice is not Recognized" Click here
Proceed to "Microphone Circuit between Microphone and Radio receiver assembly" Click here
Navigation ECU Click here
Radio and display receiver assembly Click here

USB Audio System Function
Symptom Suspected Area Link
USB audio system sound cannot be heard or sound quality is bad (USB connector is used). Proceed to "Data Signal Circuit between Stereo Jack Adapter and Extension Module" Click here
No. 1 stereo jack adapter assembly Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
USB device or "iPod" is not recognized. Proceed to "USB Audio System Recognition/Play Error" Click here
No. 1 stereo jack adapter assembly Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Track information such as track, artist and album names are not displayed. Proceed to "USB Audio System Recognition/Play Error" Click here
No. 1 stereo jack adapter assembly Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
USB device or "iPod" is recognized but cannot play, or can play but not in a sorted order. Proceed to "USB Audio System Recognition/Play Error" Click here
No. 1 stereo jack adapter assembly Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Album cover art cannot be displayed.* Check that Display Cover Art on the "iPod" or USB Settings screen is set to -
Check if similar symptoms occur with another vehicle -
If an indication to update the Gracenote database appears on the album cover art screen and update data has been downloaded to the radio and display receiver assembly, update the Gracenote database to the latest version -
Navigation ECU Click here
Radio and display receiver assembly Click here
Check if the priority display of Gracenote database album cover art setting is off* -
User set album cover art cannot be displayed. Check that a JPEG file is used for the album cover art registered to the music data in the USB device or "iPod" - radio and display receiver assembly -
Navigation ECU Click here
Radio and display receiver assembly Click here
"iPod" battery cannot be charged. Proceed to "USB Audio System Recognition/Play Error" Click here
No. 1 stereo jack adapter assembly Click here
Navigation ECU Click here
Radio and display receiver assembly Click here
Screen is distorted or not displayed only when using the video function of an "iPod". Check if "iPod" is set to output images -
Proceed to "USB Audio System Outline" in System Description and check if the "iPod" is compatible with the radio and display receiver assembly Click here
Check if the appropriate image signal setting (NTSC/ PAL) is selected -
Check if video sound input is set to "A/V" -
Connect using a known good cable and check if the image is output -
No. 1 stereo jack adapter assembly Click here
Navigation ECU Click here
Radio and display receiver assembly Click here

*: w/ Connected Services


Fuel Consumption Function
Symptom Suspected Area Link
"Fuel Consumption" icon is dimmed. Check if other icons or items displayed on screen have any problems -
Navigation ECU Click here
Radio and display receiver assembly Click here
Graph is not displayed on "Trip Information" screen. Recheck with the engine running -
Navigation ECU Click here
Radio and display receiver assembly Click here
Cruise range is not displayed on "Trip Information" screen. Turn ignition switch to ON and recheck -
Navigation ECU Click here
Radio and display receiver assembly Click here

"MirrorLink" Function (w/ "MirrorLink" Function)
Symptom Suspected Area Link
Although USB device is recognized, "MirrorLink" function cannot be started (smartphone battery can be charged). Proceed to "MirrorLink Function cannot be Started" Click here
Image is not displayed. Proceed to "MirrorLink Image is not Displayed" Click here
Sound cannot be heard. Proceed to "MirrorLink Sound cannot be Heard" Click here
"MirrorLink" is inoperative only when smartphone is connected to head unit. Proceed to "MirrorLink is Inoperative" Click here

Connected Services (w/ Connected Services)
Symptom Suspected Area Link
Connection to search engine fails. Proceed to "Connected Services" in System Description -
Contact the mobile network provider and check if the items in "Detail Setting" are set correctly -
Check if the cellular phone is in standby mode -
Check if the cellular phone is compatible with the connected service -
Check if similar symptoms occur with another vehicle -
Navigation ECU Click here
Radio and display receiver assembly Click here
POIs are not displayed on list (when using a USB device). Check if POIs are stored in USB device root folders -
Check that POIs with extension ".poi" are stored in the USB device -
Check that 256 characters (ASCII) filename is used for POIs -
Check that the file size of POIs is not 400 kb or more -
Check that nothing has been changed for downloaded POIs other than renaming them -
Navigation ECU Click here
Radio and display receiver assembly Click here
POIs cannot be registered to navigation system. Check if the maximum number of memory points has been registered -
Check that nothing has been changed for downloaded POIs other than renaming them -
Navigation ECU Click here
Radio and display receiver assembly Click here
Panoramio photos or Google street view cannot be displayed on map even though map scale is changed. Check if Panoramio photos or Google street view can be displayed at a different point -
Navigation ECU Click here
Radio and display receiver assembly Click here
Google street view "Next" or "Previous" switches cannot be selected. Wait for 90 seconds and check if the switches can be selected -
Navigation ECU Click here
Radio and display receiver assembly Click here

Traffic Information (w/ Connected Services)
Symptom Suspected Area Link
TPEG information (traffic) is not displayed on navigation screen. After turning the ignition switch from off to ACC, check if TPEG information (traffic) is displayed -
Check that the traffic messages setting is set to a position other than off. If the symptom occurs in the roaming area, check the roaming reception setting -
Check if similar symptoms occur with another vehicle -
Navigation ECU Click here
Radio and display receiver assembly Click here
TPEG information (traffic) cannot be received automatically. Check that the traffic messages setting is set to auto. If the symptom occurs in the roaming area, check the roaming reception setting -
Change the traffic messages setting to auto and wait for 10 minutes with the navigation screen on. If an error code or error message is displayed, perform the inspection according to the displayed error code or error message -
Navigation ECU Click here
Radio and display receiver assembly Click here
TPEG information (traffic) cannot be received manually. Check that the traffic messages setting is set to manual. If the symptom occurs in the roaming area, check the roaming reception setting -
Push the update switch and wait for 1 minute with the navigation screen on. Then, if an error code or error message is displayed, perform the inspection according to the displayed error code or error message -
Navigation ECU Click here
Radio and display receiver assembly Click here
Detour search using TPEG information does not operate. Check that "Dynamic reroute" is set to "Auto" or "Manual" -
Navigation ECU Click here
Radio and display receiver assembly Click here