Home › Engine / Hybrid System › A25B-FXS (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2020.08
RM3620E _51 Engine / Hybrid System _080117 A25B-FXS ENGINE MECHANICAL _0390039 ENGINE ASSEMBLY A

A25B-FXS ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:
·

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 12306 1.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly LH is necessary.


a.
A434221C02
2.313,1.885 2.469,2.083 0.156,0.198 10 true A 0.74,1.01 0.896,1.208 0.156,0.198 10 true B 2.375,0.729 2.531,0.927 0.156,0.198 10 true C
V100135

Bolt
V100136

Nut


Install the engine mounting insulator sub-assembly LH with the 2 bolts and nut.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Temporarily install the bolt (A), and then tighten the 2 bolts and nut in the order of (B), (A) and (C).



b.
A434220

Attach the claw to connect the engine room main wire.


c.

Install the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 12341 3.INSTALL ENGINE MOUNTING SPACER

HINT:

Perform this procedure only when replacement of the engine mounting spacer is necessary.


a.
A434219N01
1.188,1.771 1.344,1.938 0.156,0.167 10 true A 2.51,1.156 2.667,1.323 0.156,0.167 10 true B

Install the engine mounting spacer to the vehicle body with the 2 bolts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Temporarily install the bolt (A), and then tighten the 2 bolts in the order of (B) and (A).



Hide 12305 4.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A434218C02
0.49,1.292 0.635,1.469 0.146,0.177 10 true A 2.469,1.031 2.615,1.208 0.146,0.177 10 true B 2.406,0.531 2.552,0.708 0.146,0.177 10 true C
V100135

Bolt
V100136

Nut


Install the engine mounting insulator sub-assembly RH with the 2 bolts and nut.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Temporarily install the bolt (A), and then tighten the 2 bolts and nut in the order of (B), (A) and (C).



b.
A434217

Install the bolt to connect the No. 2 ground wire.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.
A434216

Attach the clamps to install the radiator reserve tank assembly.


d.
A434215C02
0.896,1.031 1.052,1.229 0.156,0.198 10 true 1 2.417,1.094 2.573,1.292 0.156,0.198 10 true 2
V100135

No. 6 Water By-pass Hose
V100136

Bolt
V100137

Nut


Install the bolt and nut in the order shown in the illustration.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


e.

Connect the No. 6 water by-pass hose and attach the clamp.


f.
A434214C01
2.177,0.792 2.313,0.448 true 2.063,1.635 2.063,1.01 true 1.969,1.635 2.177,1.813 0.208,0.177 10 true *1 2.229,0.281 2.458,0.448 0.229,0.167 10 true *2
*1 Suction Pipe Sub-assembly
*2 Air Conditioning Tube And Accessory Assembly


Attach the clamps to connect the suction pipe sub-assembly and air conditioning tube and accessory assembly.


g.

Connect the connector.


Hide G921A 5.INSTALL NO. 1 INVERTER RESERVE TANK BRACKET

a.

Install the No. 1 inverter reserve tank bracket with the bolt.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 7.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND

a.

Remove the engine assembly from the engine stand.


Hide 19315 8.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 31270 10.INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY

Hide 30900 11.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY

Hide 11363A 12.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 821H2 14.INSTALL HV AIR CONDITIONING WIRE

a.

for 2WD:

i.
C379387

Attach the guide to install the HV air conditioning wire to the hybrid vehicle transaxle assembly.


ii.

Install the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)



b.

for 4WD/AWD:

i.
A444947

Attach the guide to install the HV air conditioning wire to the hybrid vehicle transaxle assembly.


ii.

Install the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)



c.
A407268C02
1.313,0.552 1.583,0.26 1.583,0.26 1.708,0.26 true 1.771,0.188 2.083,0.385 0.313,0.198 10 false *a
*a Green-colored Lock
V100137

Slide


Connect the connector and slide the green-colored lock as shown in the illustration to lock it securely.

CAUTION:

Make sure to wear insulated gloves.


NOTICE:

Make sure that the connector is connected securely.



d.
A407269

Attach the clamps.


Hide 82121 15.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine assembly.


Hide 12371A 16.INSTALL REAR ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


a.

for LHD:

i.
A434224C01
0.771,1.656 0.771,1.375 true 2.219,1.896 2.219,1.615 true 1.26,1.583 1.26,1.302 false 2.51,1.885 2.51,1.25 true 1.042,1.146 0.875,0.521 true 0.708,1.677 1.021,1.875 0.313,0.198 10 false *1 2.146,1.917 2.458,2.115 0.313,0.198 10 false *2 1.188,1.594 1.5,1.792 0.313,0.198 10 false *a 0.781,0.365 1.094,0.563 0.313,0.198 10 false *b 2.448,1.906 2.76,2.104 0.313,0.198 10 false *b
*1 Rear Engine Mounting Bracket
*2 Rear Engine Mounting Insulator
*a Protrusion
*b Hole


Align the hole of the rear engine mounting insulator with the protrusion of the rear engine mounting bracket, slide the rear engine mounting insulator onto the rear engine mounting bracket to align the holes and install the rear engine mounting insulator with the bolt.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


ii.

Attach the clamp to connect the engine wire.



b.

for RHD:

i.
A434225C01
0.771,1.667 0.771,1.385 true 2.219,1.906 2.219,1.625 true 1.271,1.594 1.271,1.313 false 2.521,1.896 2.521,1.26 true 1.052,1.146 0.885,0.521 true 0.698,1.688 1.021,1.885 0.323,0.198 10 false *1 2.146,1.917 2.458,2.115 0.313,0.198 10 false *2 1.198,1.583 1.51,1.781 0.313,0.198 10 false *a 0.781,0.365 1.094,0.563 0.313,0.198 10 false *b 2.458,1.906 2.771,2.104 0.313,0.198 10 false *b
*1 Rear Engine Mounting Bracket
*2 Rear Engine Mounting Insulator
*a Protrusion
*b Hole


Align the hole of the rear engine mounting insulator with the protrusion of the rear engine mounting bracket, slide the rear engine mounting insulator onto the rear engine mounting bracket to align the holes and install the rear engine mounting insulator with the bolt.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


ii.

Attach the clamp to connect the engine wire.



Hide 82715 17.INSTALL WIRING HARNESS CLAMP BRACKET

a.

for LHD:

i.
A434209

Install the wiring harness clamp bracket with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


ii.

Attach the clamps to connect the engine wire.



b.

for RHD:

i.
A434210

Install the wiring harness clamp bracket with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


ii.

Attach the clamp to connect the engine wire.



Hide 12361 18.INSTALL FRONT ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.


Click hereDrivetrain>P710 (HYBRID TRANSMISSION / TRANSAXLE)>HYBRID VEHICLE TRANSAXLE>INSTALLATION

Hide 11361J 20.INSTALL FLYWHEEL HOUSING UNDER COVER

a.

Install the flywheel housing under cover to the cylinder block sub-assembly.


Hide 21.REMOVE ENGINE HANGERS

a.

Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly and engine mounting bracket RH.


Hide 23825 22.INSTALL FUEL DELIVERY GUARD

a.

Install the fuel delivery guard to the engine mounting bracket RH with the bolt.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 23.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

HINT:

Perform inspection after repair after replacing the engine assembly.

Click hereEngine / Hybrid System>A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Set the engine assembly with transaxle on an engine lifter.

A457674C01
0,0 0,0 false
V113146

Attachments - -


NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




b.

Operate the engine lifter and install the engine assembly with transaxle to the vehicle.

CAUTION:

Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.




c.
A434208C01
0.885,1.021 1.156,0.5 true 2.469,0.969 2.219,0.396 true 0.948,4.292 0.521,4.292 true 2.99,4.281 2.563,4.281 true 0.208,2.833 0.375,3.01 0.167,0.177 10 true A 0.375,0.24 0.531,0.438 0.156,0.198 10 true B 2.927,0.25 3.083,0.448 0.156,0.198 10 true B 1.385,4.208 1.531,4.385 0.146,0.177 10 true C 0.531,3.917 0.688,4.094 0.156,0.177 10 true D 2.063,0.25 2.281,0.417 0.219,0.167 10 true *1 1.083,0.323 1.313,0.51 0.229,0.188 10 true *2 2.969,4.167 3.177,4.323 0.208,0.156 10 true *3 0.344,4.208 0.542,4.365 0.198,0.156 10 true *4 3.094,2.792 3.26,2.969 0.167,0.177 10 true A 1.969,4.208 2.115,4.385 0.146,0.177 10 true C 0.563,4.469 0.719,4.646 0.156,0.177 10 true D 2.813,3.885 2.969,4.063 0.156,0.177 10 true D 2.771,4.448 2.927,4.625 0.156,0.177 10 true D
*1 Front Bumper Extension Sub-assembly LH
*2 Front Bumper Extension Sub-assembly RH
*3 Rear Front Suspension Member Brace LH
*4 Rear Front Suspension Member Brace RH
V100135

Bolt
V100136

Nut


Install the front bumper extension sub-assembly LH and front bumper extension sub-assembly RH to the front frame assembly and vehicle body with the 2 bolts (A), 2 bolts (B) and 4 nuts.

Torque:
Bolt (A) : 135 N*m (1377 kgf*cm, 100 ft.*lbf)
Bolt (B) : 9.5 N*m (97 kgf*cm, 84 in.*lbf)
Nut : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)


d.

Install the rear front suspension member brace LH and rear front suspension member brace RH to the front frame assembly and vehicle body with the 2 bolts (C) and 4 bolts (D).

Torque:
Bolt (C) : 135 N*m (1377 kgf*cm, 100 ft.*lbf)
Bolt (D) : 60 N*m (612 kgf*cm, 44 ft.*lbf)


e.
A434207N01
1.365,0.344 1.51,0.521 0.146,0.177 10 true A 1.052,0.615 1.198,0.792 0.146,0.177 10 true B 0.833,1.104 0.979,1.281 0.146,0.177 10 true C 0.823,1.417 0.969,1.594 0.146,0.177 10 true D

Install the engine mounting insulator sub-assembly LH to the hybrid vehicle transaxle assembly with the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:

Tighten the 4 bolts in the order of (A), (C), (B) and (D).



f.
A434206N01
2.5,0.583 2.656,0.75 0.156,0.167 10 true A 2.094,1.781 2.25,1.958 0.156,0.177 10 true B 1.219,0.219 1.375,0.396 0.156,0.177 10 true C

Install the engine mounting stay LH to the engine mounting insulator sub-assembly LH with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Temporarily install the bolt (A), and then tighten the 3 bolts in the order of (B), (C) and (A).



g.
A434205C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 3 bolts and nut.

Torque:
Bolt : 72 N*m (734 kgf*cm, 53 ft.*lbf)
Nut : 42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 45220 24.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 48069 27.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 28.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45470 29.CONNECT TIE ROD ASSEMBLY LH

Hide 45460 30.CONNECT TIE ROD ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48810 31.CONNECT FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 32.CONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 89543 33.CONNECT FRONT SPEED SENSOR LH

Hide 89542 34.CONNECT FRONT SPEED SENSOR RH

HINT:

Use the same procedure described for the LH side.


Hide 43502H 35.INSTALL FRONT AXLE SHAFT NUT LH

Hide 43501H 36.INSTALL FRONT AXLE SHAFT NUT RH

HINT:

Use the same procedure described for the LH side.


Hide 43502H 37.STAKE FRONT AXLE SHAFT NUT LH

Hide 43501H 38.STAKE FRONT AXLE SHAFT NUT RH

HINT:

Use the same procedure described for the LH side.


Hide 17410 39.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 58165C 40.INSTALL FRONT FLOOR COVER RH

a.
A434203C01
0,0 0,0 false
V100135

Bolt
V100136

Screw
V100137

Clip


Attach the clips to install the front floor cover RH.


b.

Install the 2 bolts, 3 screws and clip.

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 58166A 41.INSTALL FRONT FLOOR COVER LH

a.
A434204C01
0,0 0,0 false
V100135

Bolt
V100136

Screw
V100137

Clip


Attach the clips to install the front floor cover LH.


b.

Install the 2 bolts, 4 screws and clip.

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 51468B 42.INSTALL ENGINE UNDER COVER HEAT INSULATOR

a.

Install the engine under cover heat insulator with the 2 clips.


Hide 43.CONNECT WIRE HARNESS

a.
A434200

Install the 2 bolts to connect the ground wires.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Attach the clamp.


c.
A434201C01
0,0 0,0 false
V100135

Nut
V100136

Connector


Attach the claw to connect the wire harness to the engine room relay block and junction block assembly.


d.

Connect the connectors to the engine room relay block and junction block assembly.


e.

Install the nut to the engine room relay block and junction block assembly.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


f.
A434199

Attach the claws and remove the No. 2 relay block cover.


Hide G9229A 44.CONNECT NO. 5 INVERTER COOLING HOSE

a.

Connect the No. 5 inverter cooling hose to the motor cooling cooler, and slide the clip to secure the hose.

NOTICE:
·

Align the direction of the claw on the clip with the paint mark on the hose.

·

Make sure the No. 5 inverter cooling hose is securely inserted to the stopper.



A434230C01
4.115,1.24 3.844,0.656 true 3.365,0.458 3.615,0.677 0.25,0.219 10 true *a 4.563,0.813 4.875,0.969 0.313,0.156 10 false *b 3.74,0.479 4.052,0.635 0.313,0.156 10 false *c 4.052,0.604 4.365,0.76 0.313,0.156 10 false *d 3.281,1.479 3.594,1.635 0.313,0.156 10 false *e 5.688,1.969 6,2.125 0.313,0.156 10 false *f 1.635,1.521 1.792,1.719 0.156,0.198 10 true A
*a View A *b 120°
*c Paint Mark *d Upper Side
*e Front Side *f 2 to 7 mm (0.0787 to 0.276 in.)



Hide 88704 45.CONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 88711 46.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

Hide 16572D 47.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the water inlet, and slide the clip to secure the hose.

NOTICE:
·

Align the direction of the claw on the clip with the paint mark on the hose.

·

Make sure the No. 2 radiator hose is securely inserted to the stopper.



A434231C01
4.104,1.229 3.917,0.573 true 3.292,0.49 3.677,0.74 0.385,0.25 10 true *a 4.563,0.833 4.875,0.99 0.313,0.156 10 false *b 3.823,0.406 4.135,0.563 0.313,0.156 10 false *c 4.042,0.635 4.354,0.792 0.313,0.156 10 false *d 3.271,1.49 3.583,1.646 0.313,0.156 10 false *e 5.677,1.958 5.99,2.115 0.313,0.156 10 false *f 1.229,1.531 1.375,1.698 0.146,0.167 10 true A
*a View A *b 120°
*c Paint Mark *d Upper Side
*e RH Side *f 2 to 7 mm (0.0787 to 0.276 in.)



Hide 16571C 48.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the No. 1 radiator hose to the water outlet, and slide the clip to secure the hose.

NOTICE:
·

Align the direction of the claw on the clip with the paint mark on the hose.

·

Make sure the No. 1 radiator hose is securely inserted to the stopper.




b.

Attach the clamp.

A434232C01
4.115,1.24 3.875,0.625 true 3.313,0.521 3.698,0.771 0.385,0.25 10 true *a 4.542,0.823 4.854,0.979 0.313,0.156 10 false *b 3.771,0.448 4.083,0.604 0.313,0.156 10 false *c 4.052,0.656 4.365,0.813 0.313,0.156 10 false *d 3.271,1.49 3.583,1.646 0.313,0.156 10 false *e 5.667,1.958 5.979,2.115 0.313,0.156 10 false *f 1.885,0.885 2.031,1.052 0.146,0.167 10 true A
*a View A *b 120°
*c Paint Mark *d Front Side
*e RH Side *f 2 to 7 mm (0.0787 to 0.276 in.)



Hide 87245 49.CONNECT INLET HEATER WATER HOSE

a.
A403462C04
1.01,0.979 1.438,0.979 false 1.875,0.969 2.302,0.969 false 1.021,1.354 1.448,1.354 false 1.844,1.365 2.281,1.917 2.281,1.917 2.594,1.917 true 0.813,0.885 1.125,1.042 0.313,0.156 10 false *a 0.833,1.271 1.146,1.427 0.313,0.156 10 false *b 2.365,0.896 2.677,1.052 0.313,0.156 10 false *a 2.635,1.823 2.948,1.979 0.313,0.156 10 false *b
*a Protrusion
*b Cutout


Align the protrusions of the inlet heater water hose connector with the cutouts in the flow shutting valve (water by-pass hose assembly) and securely insert the inlet heater water hose connector to the stopper of the pipe.


b.
A434227C01
0.771,1.792 1.323,1.563 true 0.542,1.75 0.76,1.938 0.219,0.188 10 true *a
*a Retainer
V113147

Push
V113148

Push in


Push in the retainer.


c.

Check that the flow shutting valve (water by-pass hose assembly) and inlet heater hose connector are securely connected by pulling on them.


Hide 87246 50.CONNECT OUTLET HEATER WATER HOSE

a.
A403463C04
1.052,1.156 1.573,1.156 false 0.99,0.365 1.219,0.365 1.219,0.365 1.521,0.792 true 0.875,1.063 1.188,1.219 0.313,0.156 10 false *a 0.823,0.281 1.135,0.438 0.313,0.156 10 false *b
*a Protrusion
*b Cutout


Align the protrusion of the No. 2 water by-pass pipe sub-assembly with the cutout in the outlet heater water hose connector and securely insert the outlet heater water hose connector to the stopper of the pipe.


b.
A434226C01
0.927,1.802 1.688,1.552 true 0.729,1.75 0.948,1.938 0.219,0.188 10 true *a
*a Retainer
V113147

Push
V113148

Push in


Push in the retainer.


c.

Check that the No. 2 water by-pass pipe sub-assembly and outlet heater hose connector are securely connected by pulling on them.


Hide 23901 51.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly.

i.
A434193

Connect the fuel tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>A25B-FXS (FUEL)>FUEL SYSTEM>PRECAUTION



b.
A434192

Install the No. 1 fuel pipe clamp to the fuel tube connector.

Click hereEngine / Hybrid System>A25B-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 23826 52.CONNECT NO. 1 FUEL VAPOR FEED HOSE

a.
A434191

Connect the No. 1 fuel vapor feed hose to the purge VSV.


b.

Attach the clamp.


Hide 16282 53.INSTALL NO. 5 WATER BY-PASS HOSE

a.

Install the No. 5 water by-pass hose to the No. 3 water by-pass pipe and radiator assembly, and slide the clips to secure the hose.

NOTICE:
·

Align the direction of the claw on the clip with the paint mark on the hose.

·

Make sure the No. 5 water by-pass hose is securely inserted to the stopper.



A434233C01
3.948,0.802 3.677,0.479 true 6.635,0.594 6.25,1.125 true 3.271,0.385 3.49,0.604 0.219,0.219 10 true *a 5.292,0.375 5.604,0.531 0.313,0.156 10 false *b 4.292,0.531 4.604,0.688 0.313,0.156 10 false *c 6.521,1.667 6.833,1.823 0.313,0.156 10 false *d 3.896,0.313 4.208,0.469 0.313,0.156 10 false *f 1.958,1.875 2.104,2.042 0.146,0.167 10 true A 0.906,1.292 1.052,1.458 0.146,0.167 10 true B 3.573,0.313 3.885,0.469 0.313,0.156 10 false *e 6.604,0.438 6.917,0.594 0.313,0.156 10 false *e 5.854,0.313 6.167,0.469 0.313,0.156 10 false *f 4.698,1.063 4.917,1.25 0.219,0.188 10 false *g 6.729,1.083 6.948,1.271 0.219,0.188 10 false *h 4.917,2.396 5.135,2.583 0.219,0.188 10 false *i
*a View A *b View B
*c 360° *d 120°
*e Paint Mark *f Upper Side
*g Front Side *h Rear Side
*i 2 to 7 mm (0.0787 to 0.276 in.) - -



Hide G92A0A 54.INSTALL INVERTER RESERVE TANK ASSEMBLY

a.

Connect the No. 2 inverter cooling hose and No. 5 inverter cooling hose to the inverter reserve tank assembly, and slide the clips to secure the hoses.

NOTICE:
·

Align the direction of the claw on the clip with the paint mark on the hose.

·

Make sure the No. 2 inverter cooling hose and No. 5 inverter cooling hose are securely inserted to the stopper.



A434235C01
4.115,0.458 3.958,0.896 true 6.052,0.917 6.26,0.438 true 3.229,0.323 3.448,0.542 0.219,0.219 10 true *a 5.198,0.333 5.51,0.49 0.313,0.156 10 false *b 4.438,0.521 4.75,0.677 0.313,0.156 10 false *c 6.198,0.292 6.51,0.448 0.313,0.156 10 false *d 3.156,1.156 3.469,1.313 0.313,0.156 10 false *f 0.917,1.656 1.063,1.823 0.146,0.167 10 true A 1.719,1.677 1.865,1.844 0.146,0.167 10 true B 3.865,0.271 4.177,0.427 0.313,0.156 10 false *e 5.938,0.281 6.25,0.438 0.313,0.156 10 false *e 5.229,1.146 5.448,1.333 0.219,0.188 10 false *f 4.542,2.146 4.771,2.396 0.229,0.25 10 false *g 6.542,0.531 6.854,0.688 0.313,0.156 10 false *c 4.052,0.302 4.365,0.458 0.313,0.156 10 false *d
*a View A *b View B
*c 120° *d Paint Mark
*e Upper Side *f RH Side
*g 2 to 7 mm (0.0787 to 0.276 in.) - -



b.
A434234C01
2.74,0.49 2,0.635 true 2.198,1.021 2.646,1.021 true 1.833,0.552 2.073,0.75 0.24,0.198 10 false *a 2.031,0.927 2.271,1.125 0.24,0.198 10 false *b
*a Pin
*b Grommet


Fit the pin of the inverter reserve tank assembly into grommet as shown in the illustration.


c.

Install the inverter reserve tank assembly with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 56.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 17750A 57.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 12601B 58.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

a.

for LHD:

i.
A434228

Attach the clips to install the No. 1 engine cover sub-assembly.

NOTICE:
·

Securely attach the clips.

·

If the clips are forcibly attached or struck with an object, they may be damaged.





b.

for RHD:

i.
A434229

Attach the clips to install the No. 1 engine cover sub-assembly.

NOTICE:
·

Securely attach the clips.

·

If the clips are forcibly attached or struck with an object, they may be damaged.





Hide 52132A 59.INSTALL FRONT BUMPER NO. 2 REINFORCEMENT

Hide 52618 60.INSTALL FRONT LOWER BUMPER ABSORBER

a.
A434202

Attach the claws to install the front lower bumper absorber.


b.

Install the clip.


Hide 53737D 63.INSTALL FRONT FENDER APRON SEAL LH

a.
A434185C01
0,0 0,0 false
V100135

Bolt
V100136

Clip


Install the front fender apron seal LH with the 2 bolts and clip.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 53736E 64.INSTALL FRONT FENDER APRON SEAL RH

a.
A434186C01
0,0 0,0 false
V100135

Bolt
V100136

Clip


Install the front fender apron seal RH with the 2 bolts and clip.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 51420 65.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

a.
A434183C01
0,0 0,0 false
V100135

Bolt
V100136

Screw
V100137

Clip


Install the No. 2 engine under cover assembly with the 2 bolts, 2 screws and 6 clips.

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 51441 66.INSTALL NO. 1 ENGINE UNDER COVER

a.

Attach the guide to install the No. 1 engine under cover.


b.

Install the 2 bolts and 8 screws.

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)

A474576C01
0,0 0,0 false
V100135

Bolt
V100136

Screw



Hide 53896B 67.INSTALL FRONT FENDER FRONT SPLASH SHIELD LH

a.
A434180

Attach the clip to install the front fender front splash shield LH.


b.

Install the 3 screws.


Hide 53895B 68.INSTALL FRONT FENDER FRONT SPLASH SHIELD RH

a.
A434181

Attach the clip to install the front fender front splash shield RH.


b.

Install the 3 screws.


Hide 58441J 70.INSTALL BATTERY SERVICE HOLE COVER

Hide 71.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 65351A 72.INSTALL BATTERY HOLE COVER

Hide 58416K 73.INSTALL REAR NO. 2 FLOOR BOARD

Hide 58410B 74.INSTALL DECK BOARD ASSEMBLY

Hide 80.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 81.ADD ENGINE COOLANT (for Engine)

Hide 83.INSPECT FOR ENGINE OIL LEAK

Hide 84.INSPECT FOR COOLANT LEAK (for Engine)

Hide 89.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR

Hide 90.INSTALL FRONT WHEELS

Hide 91. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 92.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 93.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY