Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PIPE
RM3650E _54 Brake _079889 BRAKE SYSTEM (OTHER) _0387651 BRAKE PIPE A

BRAKE SYSTEM (OTHER)  BRAKE PIPE  REPLACEMENT  


PROCEDURE

Hide 85010 1.REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY (for RHD)

Hide 3.REMOVE FUEL TANK ASSEMBLY (for Rear Side)

Hide 4.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY (for Rear Side)

Hide 5.REMOVE SEALING FRAME

a.
C413621

Unscrew the T25 screws (1) and remove the sealing frame (2).


Hide 6.REMOVE ALL BRAKE PIPES

a.
C413616

Loosen union nut (1) with special tool 0 492 482 (34 3 170). Use the square end (2) for counter support if necessary.

SST
09700-WA070  


b.
C418396

for RHD:

i.

Release brake pipes (1) with the special tool 0 492 482 (34 3 170). Use the square end (2) for counter support if necessary.

SST
09700-WA070  


ii.

Remove the 2 tube way.



c.
C413610

Release brake pipes (1) with the special tool 0 492 482 (34 3 170).

SST
09700-WA070  


d.
C413617

Release brake pipes (1) with the special tool 0 492 482 (34 3 170).

SST
09700-WA070  


e.

for LHD:

i.

Unclip and remove all brake pipes.

C415180



f.

for RHD:

i.

Unclip and remove all brake pipes.

C415181



Hide 7.INSTALL ALL BRAKE PIPES

a.

for LHD:

i.

Install and clip in all brake pipes.



b.

for RHD:

i.

Install and clip in all brake pipes.



c.
C415176C01
3.094,0.938 3.406,1.135 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


Position the union nut (1) and tighten it with the special tool 0 492 482 (34 3 170). Use the square end (2) for counter support if necessary.

SST
09700-WA070  

Torque:
Specified tightening torque : 17 N*m (173 kgf*cm, 13 ft.*lbf)

HINT:

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



d.
C415179C01
1.552,0.896 1.865,1.052 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


for RHD:

i.

Position the union nut (1) and tighten it with the special tool 0 492 482 (34 3 170). Use the square end (2) for counter support if necessary.

SST
09700-WA070  

Torque:
Specified tightening torque : 17 N*m (173 kgf*cm, 13 ft.*lbf)

HINT:

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




e.
C415177C01
1.604,3.094 1.917,3.292 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


Tighten the brake pipes (1) with the special tool 0 492 482 (34 3 170).

SST
09700-WA070  

Torque:
Specified tightening torque : 17 N*m (173 kgf*cm, 13 ft.*lbf)

HINT:

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



f.
C415178C01
1.552,3.104 1.781,3.313 0.229,0.208 10 true *a
*a Torque Wrench Fulcrum Length


Tighten the brake pipes (1) with the special tool 0 492 482 (34 3 170).

SST
09700-WA070  

Torque:
Specified tightening torque : 17 N*m (173 kgf*cm, 13 ft.*lbf)

HINT:

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



Hide 8.INSTALL SEALING FRAME

a.
C413621

Position the sealing frame (2) and tighten the T25 screws (1).

Torque:
2.8 N*m (29 kgf*cm, 25 in.*lbf)


Hide 9.INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY (for Rear Side)

Hide 10.INSTALL FUEL TANK ASSEMBLY (for Rear Side)

Hide 85010 12.INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY (for RHD)