Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM

NAVIGATION SYSTEM > Speaker Circuit

for Preparation Click here


DESCRIPTION

The navigation receiver assembly sends sound signals to the speakers.

WIRING DIAGRAM


E282414E02


E282415E02


E282416E03


E282417E02


E282418E04


INSPECTION PROCEDURE

1.CHECK VEHICLE CONDITION
  1. Check the vehicle condition.
    Result 
    Result
    Proceed to
    for 4 Speakers
    A
    for 7 or 9 Speakers
    B
    for 12 Speakers
    C



B
Go to step 5

C
Go to step 12
A


2.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
  1. *1: for RH Side
  2. *2: for LH Side
  1. Disconnect the J133 navigation receiver assembly connector.

  1. Disconnect the M8*1 and/or N10*2 front No. 1 speaker assembly connector.

  1. Disconnect the J147*1 and/or J149*2 front No. 2 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J133-1 (FR+) - J147-3 (TWR+)
    Always
    Below 1 Ω
    J133-5 (FR-) - J147-2 (TWR-)
    Always
    Below 1 Ω
    M8-1 - J147-1 (+)
    Always
    Below 1 Ω
    M8-2 - J147-4 (-)
    Always
    Below 1 Ω
    J133-2 (FL+) - J149-3 (TWL+)
    Always
    Below 1 Ω
    J133-6 (FL-) - J149-2 (TWL-)
    Always
    Below 1 Ω
    N10-1 - J149-1 (+)
    Always
    Below 1 Ω
    N10-2 - J149-4 (-)
    Always
    Below 1 Ω
    J133-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    J133-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    M8-2 - Body ground
    Always
    10 kΩ or higher
    M8-1 - Body ground
    Always
    10 kΩ or higher
    J133-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    J133-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    N10-2 - Body ground
    Always
    10 kΩ or higher
    N10-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly (Click here).

  1. Inspect the front No. 1 speaker assembly (Click here).



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


4.CHECK FRONT NO. 2 SPEAKER ASSEMBLY
  1. Replace the front No. 2 speaker assembly with a known good one (Click here)

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Column Shift Type)
    B
    NG (for Floor Shift Type)
    C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
A

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

5.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
  1. *1: for RH Side
  2. *2: for LH Side
  3. *3: for 9 Speakers
  1. Disconnect the J133 and J134 navigation receiver assembly connector.

  1. Disconnect the M8*1 and/or N10*2 front No. 1 speaker assembly connector.

  1. Disconnect the J147*1 and/or J149*2 front No. 2 speaker assembly connector.

  1. Disconnect the J150 front No. 4 speaker assembly connector.

  1. Disconnect the O1*1 and/or O7*2 rear No. 1 speaker assembly connector.

  1. Disconnect the O2*1 and/or O8*2 rear No. 2 speaker assembly connector.*3

  1. Disconnect the J144 and J145 stereo component amplifier assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M8-1 - J144-1 (R+)
    Always
    Below 1 Ω
    M8-2 - J144-5 (R-)
    Always
    Below 1 Ω
    N10-1 - J144-2 (L+)
    Always
    Below 1 Ω
    N10-2 - J144-6 (L-)
    Always
    Below 1 Ω
    O1-1 - J145-4 (WFR+)
    Always
    Below 1 Ω
    O1-2 - J145-11 (WFR-)
    Always
    Below 1 Ω
    O7-1 - J145-5 (WFL+)
    Always
    Below 1 Ω
    O7-2 - J145-12 (WFL-)
    Always
    Below 1 Ω
    O2-3 - J145-9 (RR+)*3
    Always
    Below 1 Ω
    O2-2 - J145-10 (RR-)*3
    Always
    Below 1 Ω
    J145-9 (RR+) - J134-1 (RR+)
    Always
    Below 1 Ω
    J145-10 (RR-) - J134-3 (RR-)
    Always
    Below 1 Ω
    O8-3 - J145-3 (RL+)*3
    Always
    Below 1 Ω
    O8-2 - J145-8 (RL-)*3
    Always
    Below 1 Ω
    J145-3 (RL+) - J134-2 (RL+)
    Always
    Below 1 Ω
    J145-8 (RL-) - J134-6 (RL-)
    Always
    Below 1 Ω
    J145-2 (FR+) - J133-1 (FR+)
    Always
    Below 1 Ω
    J145-7 (FR-) - J133-5 (FR-)
    Always
    Below 1 Ω
    J145-1 (FL+) - J133-2 (FL+)
    Always
    Below 1 Ω
    J145-6 (FL-) - J133-6 (FL-)
    Always
    Below 1 Ω
    J145-2 (FR+) - J147-3 (TWR+)
    Always
    Below 1 Ω
    J145-7 (FR-) - J147-2 (TWR-)
    Always
    Below 1 Ω
    J145-1 (FL+) - J149-3 (TWL+)
    Always
    Below 1 Ω
    J145-6 (FL-) - J149-2 (TWL-)
    Always
    Below 1 Ω
    J147-1 (+) - J150-1 (+)
    Always
    Below 1 Ω
    J147-4 (-) - J150-4 (RI1-)
    Always
    Below 1 Ω
    J150-2 (-) - J149-4 (-)
    Always
    Below 1 Ω
    J150-3 (RI1+) - J149-1 (+)
    Always
    Below 1 Ω
    J144-1 (R+) - Body ground
    Always
    10 kΩ or higher
    J144-5 (R-) - Body ground
    Always
    10 kΩ or higher
    J144-2 (L+) - Body ground
    Always
    10 kΩ or higher
    J144-6 (L-) - Body ground
    Always
    10 kΩ or higher
    J145-4 (WFR+) - Body ground
    Always
    10 kΩ or higher
    J145-11 (WFR-) - Body ground
    Always
    10 kΩ or higher
    J145-5 (WFL+) - Body ground
    Always
    10 kΩ or higher
    J145-12 (WFL-) - Body ground
    Always
    10 kΩ or higher
    J145-9 (RR+) - Body ground
    Always
    10 kΩ or higher
    J145-10 (RR-) - Body ground
    Always
    10 kΩ or higher
    J145-3 (RL+) - Body ground
    Always
    10 kΩ or higher
    J145-8 (RL-) - Body ground
    Always
    10 kΩ or higher
    J145-2 (FR+) - Body ground
    Always
    10 kΩ or higher
    J145-7 (FR-) - Body ground
    Always
    10 kΩ or higher
    J145-1 (FL+) - Body ground
    Always
    10 kΩ or higher
    J145-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    J147-1 (+) - Body ground
    Always
    10 kΩ or higher
    J147-4 (-) - Body ground
    Always
    10 kΩ or higher
    J147-3 (TWR+) - Body ground
    Always
    10 kΩ or higher
    J147-2 (TWR-) - Body ground
    Always
    10 kΩ or higher
    J150-2 (-) - Body ground
    Always
    10 kΩ or higher
    J150-3 (RI1+) - Body ground
    Always
    10 kΩ or higher
    J149-3 (TWL+) - Body ground
    Always
    10 kΩ or higher
    J149-2 (TWL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly.

    1. for Double Cab: Click here
    2. for CrewMax: Click here

  1. Inspect the front No. 1 speaker assembly.

    1. for Double Cab: Click here
    2. for CrewMax: Click here
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Double Cab)
    B
    NG (for CrewMax)
    C



B
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)

C
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
A


7.CHECK FRONT NO. 2 SPEAKER ASSEMBLY
  1. Replace the front No. 2 speaker assembly with a known good one.

    1. for Double Cab: Click here
    2. for CrewMax: Click here

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 8
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

8.CHECK FRONT NO. 4 SPEAKER ASSEMBLY
  1. Replace the front No. 4 speaker assembly with a known good one.

    1. for Double Cab: Click here
    2. for CrewMax: Click here

  1. Check that the malfunction disappears.

    OK:
    Malfunction disappears.



NG
Go to step 9
OK

END (FRONT NO. 4 SPEAKER ASSEMBLY IS DEFECTIVE) 

9.CHECK REAR NO. 1 SPEAKER ASSEMBLY
  1. Remove the rear No. 1 speaker assembly with a known good one.

    1. for Double Cab: Click here
    2. for CrewMax: Click here

  1. Inspect the rear No. 1 speaker assembly with a known good one.

    1. for Double Cab: Click here
    2. for CrewMax: Click here
    Result 
    Result
    Proceed to
    OK (for CrewMax)
    A
    OK (for Double Cab)
    B
    NG (for Double Cab)
    C
    NG (for CrewMax)
    D



B
Go to step 11

C
REPLACE REAR NO. 1 SPEAKER ASSEMBLY (Click here)

D
REPLACE REAR NO. 1 SPEAKER ASSEMBLY (Click here)
A


10.CHECK REAR NO. 2 SPEAKER ASSEMBLY
  1. Replace the rear No. 2 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
    2. Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 11
OK

END (REAR NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

11.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
  1. Replace the stereo component amplifier assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    OK:
    Malfunction disappears.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Double Cab)
    B
    NG (for CrewMax)
    C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
A

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE) 

12.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
  1. *1: for RH Side
  2. *2: for LH Side
  1. Disconnect the M8*1 and/or N10*2 front No. 1 speaker assembly connector.

  1. Disconnect the J146*1 and/or J148*2 front No. 2 speaker assembly connector.

  1. Disconnect the M1*1 and/or N1*2 front No. 3 speaker assembly connector.

  1. Disconnect the J150 front No. 4 speaker assembly connector.

  1. Disconnect the O1*1 and/or O7*2 rear No. 1 speaker assembly connector.

  1. Disconnect the O2*1 and/or O8*2 rear No. 2 speaker assembly connector.

  1. Disconnect the P14 No. 1 box speaker assembly connector.

  1. Disconnect the J142 and J143 stereo component amplifier assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J142-2 (FR+) - J146-3 (TWR+)
    Always
    Below 1 Ω
    J142-6 (FR-) - J146-4 (TWR-)
    Always
    Below 1 Ω
    J146-1 (+) - M1-3
    Always
    Below 1 Ω
    J146-2 (-) - M1-2
    Always
    Below 1 Ω
    J143-9 (WFR+) - M8-1
    Always
    Below 1 Ω
    J143-3 (WFR-) - M8-2
    Always
    Below 1 Ω
    J142-10 (RR+) - O2-3 (+TW)
    Always
    Below 1 Ω
    J142-4 (RR-) - O2-2 (-TW)
    Always
    Below 1 Ω
    O2-4 (+) - O1-2
    Always
    Below 1 Ω
    O2-1 (-) - O1-1
    Always
    Below 1 Ω
    J142-5 (WF1+) - P14-1
    Always
    Below 1 Ω
    J142-12 (WF1-) - P14-2
    Always
    Below 1 Ω
    J142-3 (RL+) - O8-3 (+TW)
    Always
    Below 1 Ω
    J142-9 (RL-) - O8-2 (-TW)
    Always
    Below 1 Ω
    O8-4 (+) - O7-1
    Always
    Below 1 Ω
    O8-1 (-) - O7-2
    Always
    Below 1 Ω
    J143-2 (WFL+) - N10-1
    Always
    Below 1 Ω
    J143-1 (WFL-) - N10-2
    Always
    Below 1 Ω
    J142-8 (FL+) - J148-3 (TWL+)
    Always
    Below 1 Ω
    J142-7 (FL-) - J148-4 (TWL-)
    Always
    Below 1 Ω
    J148-1 (+) - N1-3
    Always
    Below 1 Ω
    J148-2 (-) - N1-2
    Always
    Below 1 Ω
    J143-4 (CTR+) - J150-1
    Always
    Below 1 Ω
    J143-10 (CTR-) - J150-2
    Always
    Below 1 Ω
    J142-2 (FR+) - Body ground
    Always
    10 kΩ or higher
    J142-6 (FR-) - Body ground
    Always
    10 kΩ or higher
    J146-1 (+) - Body ground
    Always
    10 kΩ or higher
    J146-2 (-) - Body ground
    Always
    10 kΩ or higher
    J143-9 (WFR+) - Body ground
    Always
    10 kΩ or higher
    J143-3 (WFR-) - Body ground
    Always
    10 kΩ or higher
    J142-10 (RR+) - Body ground
    Always
    10 kΩ or higher
    J142-4 (RR-) - Body ground
    Always
    10 kΩ or higher
    O2-4 (+) - Body ground
    Always
    10 kΩ or higher
    O2-1 (-) - Body ground
    Always
    10 kΩ or higher
    J142-5 (WF1+) - Body ground
    Always
    10 kΩ or higher
    J142-12 (WF1-) - Body ground
    Always
    10 kΩ or higher
    J142-3 (RL+) - Body ground
    Always
    10 kΩ or higher
    J142-9 (RL-) - Body ground
    Always
    10 kΩ or higher
    O8-4 (+) - Body ground
    Always
    10 kΩ or higher
    O8-1 (-) - Body ground
    Always
    10 kΩ or higher
    J143-2 (WFL+) - Body ground
    Always
    10 kΩ or higher
    J143-1 (WFL-) - Body ground
    Always
    10 kΩ or higher
    J142-8 (FL+) - Body ground
    Always
    10 kΩ or higher
    J142-7 (FL-) - Body ground
    Always
    10 kΩ or higher
    J148-1 (+) - Body ground
    Always
    10 kΩ or higher
    J148-2 (-) - Body ground
    Always
    10 kΩ or higher
    J143-4 (CTR+) - Body ground
    Always
    10 kΩ or higher
    J143-10 (CTR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly (Click here).

  1. Inspect the front No. 1 speaker assembly (Click here).



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


14.CHECK FRONT NO. 2 SPEAKER ASSEMBLY
  1. Replace the front No. 2 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 15
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

15.CHECK FRONT NO. 4 SPEAKER ASSEMBLY
  1. Replace the front No. 4 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    OK:
    Malfunction disappears.



NG
Go to step 16
OK

END (FRONT NO. 4 SPEAKER ASSEMBLY IS DEFECTIVE) 

16.CHECK FRONT NO. 3 SPEAKER ASSEMBLY
  1. Replace the front No. 3 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the front No. 3 speaker assemblies that were disconnected.
    2. Connect all the connectors to the front No. 3 speaker assemblies that were disconnected.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 17
OK

END (FRONT NO. 3 SPEAKER ASSEMBLY IS DEFECTIVE) 

17.CHECK NO. 1 BOX SPEAKER ASSEMBLY
  1. Remove the No. 1 box speaker assembly (Click here).

  1. Inspect the No. 1 box speaker assembly (Click here).



NG
REPLACE NO. 1 BOX SPEAKER ASSEMBLY
OK


18.CHECK REAR NO. 1 SPEAKER ASSEMBLY
  1. Remove the rear No. 1 speaker assembly (Click here).

  1. Inspect the rear No. 1 speaker assembly (Click here).



NG
REPLACE REAR NO. 1 SPEAKER ASSEMBLY (Click here)
OK


19.CHECK REAR NO. 2 SPEAKER ASSEMBLY
  1. Replace the rear No. 2 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
    2. Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 20
OK

END (REAR NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

20.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
  1. Replace the stereo component amplifier assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    OK:
    Malfunction disappears.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Column Shift Type)
    B
    NG (for Floor Shift Type)
    C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
A

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)