DTC P1604 Startability Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| P1604 | Either condition is met:
|
|

| Malfunction Recurrence and Inspection Areas |
Freeze frame data exists, but the malfunction (starting difficulty) has not reoccurred and the malfunction conditions are unknown.
The engine speed recorded in the freeze frame data is 0 rpm (the engine does not crank).

All engine speeds recorded in the freeze frame data are between 100 and 250 rpm (the engine cranks but there is no combustion).

The engine speed recorded in the freeze frame data is 250 rpm or higher (the initial combustion and starter turnoff timing is too late).

When the malfunction (starting difficulty) can be reproduced, or malfunction conditions are known, confirm the following details of the problem symptom and inspect the systems listed below.
Problem Symptoms
Systems to Inspect
| INSPECTION FLOW |
Freeze frame data exists, but the malfunction (starting difficulty) has not reoccurred and the malfunction conditions are unknown.
| Freeze Frame Data Item | Result | Suspected Area | Procedure |
| Engine Speed | 0 rpm (no engine cranking at all) |
| 4 to 9 |
| 100 to 250 rpm (engine cranks but no initial combustion*1) |
| 10 to 14 | |
| 250 rpm or higher (combustion occurs but initial combustion and starter turnoff*2 occur late) |
| 15 to 23 |
When the malfunction (starting difficulty) can be reproduced, or when malfunction conditions are known.
Problem Symptoms
| Problem Symptom | Suspected Area | Suspected Component | Procedure |
| The engine does not crank | Battery malfunction |
| 26 to 31 |
| Starting system |
| ||
| Engine assembly |
| ||
| Cranking speed too low | Battery malfunction |
| 32 to 34 |
| Starting system |
| ||
| Engine assembly |
| ||
| Cranking speed too high | Engine assembly |
| |
| There is no initial combustion | Fuel supply problem |
| 35 to 48 |
| Immobiliser system |
| ||
| Ignition system malfunction |
| ||
| Engine stalls after starter turnoff | Air suction |
| 49 to 55 |
| Deposits in throttle body |
| ||
| VVT valve does not return properly |
| ||
| Mass air flow meter malfunction |
| ||
| Initial combustion and starter turnoff occur late | Engine coolant temperature sensor malfunction |
| 56 to 69 |
| Mass air flow meter malfunction |
| ||
| Abnormal A/F learned value |
| ||
| Deviation from fuel injection characteristics |
| ||
| Wet-fouled or dry-fouled spark plug |
| ||
| Lack of fuel pressure |
|
Systems to Inspect
| Troubleshooting by System | Suspected Area | Suspected Component | Procedure |
| Fuel system troubleshooting A | Abnormal A/F learned value |
| 84 to 91 92 to 99 |
| Rough idling |
| ||
| Abnormal fuel pressure |
| ||
| Fuel system troubleshooting B | Abnormal concentration of HC in surge tank |
| 100 to 102 |
| Fuel system troubleshooting C | Injection signal system malfunction |
| 71 to 80 |
| Intake system troubleshooting | Difference between ISC target value and opening angle when idling |
| 81 to 83 103 to 105 |
| Ignition system troubleshooting | Camshaft and/or crankshaft position sensor signal malfunction |
| 75 to 80 106 to 111 |
| 1.CHECK FOR ANY OTHER DTCS OUTPUT AND RECORD FREEZE FRAME DATA |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
![]() |
Read the DTCs and record the freeze frame data.
| Result | Proceed to |
| Only DTC P1604 is output | A |
| DTCs other than P1604 are output | B |
|
| ||||
| A | |
| 2.CHECK ENGINE IMMOBILISER SYSTEM |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Immobiliser Fuel Cut.
Read the value displayed on the Techstream.
|
| ||||
| OK | |
| 3.CHECK MALFUNCTION CONDITION |
Confirm the problem symptoms.
| Result | Proceed to |
| Freeze frame data exists, but the starting difficulty cannot be reproduced and it is unknown what kind of starting difficulty occurred | A |
| The problem symptoms can be reproduced, or the malfunction conditions are known | B |
|
| ||||
| A | |
| 4.CHECK FREEZE FRAME DATA |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Suspected Area | Proceed to | |
| Engine Speed | Battery Voltage | ||
| All 5 sets of freeze frame data are 0 rpm (no engine cranking at all) | Minimum voltage is below 5 V | Battery fully depleted | A |
| Minimum voltage is 5 V or higher |
| B | |
| 60 to 250 rpm (engine cranks but no initial combustion) | - |
| C |
| 250 rpm or higher (combustion occurs but initial combustion and starter turnoff occur late) | - |
| D |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 5.CHECK FREEZE FRAME DATA |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Battery Voltage | Minimum voltage is 6 V or higher and voltage does not fluctuate*1 | Starter system | A |
| Minimum voltage is 6 V or higher and voltage fluctuates*2, *3 |
| B | |
| Minimum voltage is 5 to 6 V*4 |
| C |
![]() |
|
| ||||
|
| ||||
| A | ||
| ||
| 6.CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION) |
Check the tightening torque and installation condition of the crankshaft position sensor bolt.
Check the connection of the crankshaft position sensor connector.
| Result | Proceed to |
| Normal | A |
| Abnormal | B |
|
| ||||
| A | |
| 7.CHECK CRANKSHAFT POSITION SENSOR |
Disconnect the crankshaft position sensor connector.
Check for oil on the connector terminals.
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
Check the harnesses and connectors, referring to DTC P0335 inspection procedure .
|
| ||||
| OK | |
| 9.CHECK CRANKSHAFT POSITION SENSOR |
Replace the crankshaft position sensor (Click here).
Check the engine start operation.
|
| ||||
| OK | ||
| ||
| 10.CHECK FREEZE FRAME DATA |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Suspected Area | Proceed to | ||
| Coolant Temp, Ambient Temp for A/C, Intake Air | Coolant Temp, Ambient Temp for A/C | Fuel Pump Duty | ||
| Difference between Coolant Temp, Ambient Temp for A/C and Intake Air is 10°C or more*1 | Coolant Temp is 125°C or higher, or below Ambient Temp for A/C by 15°C or more | - | Engine coolant temperature sensor | A |
| Other than above | No sets of freeze frame data are 0% | - | B | |
| At least 1 of the 5 sets of freeze frame data is 0% | Fuel pump control circuit | C | ||
| Difference between Coolant Temp, Ambient Temp for A/C and Intake Air is less than 10°C*2 | - | At least 1 of the 5 sets of freeze frame data is 0% | Fuel pump control circuit | C |
| No sets of freeze frame data are 0% | - | B | ||
|
| ||||
|
| ||||
| A | ||
| ||
| 11.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP / SPEED) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for an operating sound from the fuel pump.
| Control the Fuel Pump / Speed | Specified Condition |
| ON | Operating sound heard |
| OFF | Operating sound not heard |
|
| ||||
| OK | |
| 12.CHECK TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE) |
Check the harnesses and connectors, referring to DTC P0300 inspection procedure .
|
| ||||
| OK | |
| 13.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP / SPEED) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for fuel leakage from the fuel pipes.
| Result | Proceed to |
| Fuel leakage or signs of fuel leakage are present | A |
| No fuel leakage or signs of fuel leakage | B |
|
| ||||
| A | ||
| ||
| 14.CHECK FUEL SYSTEM |
Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter, and inside the fuel tank), and for signs that the fuel pump was stuck.
| Result | Proceed to |
| There is foreign matter or signs that fuel pump was stuck | A |
| There is no foreign matter and no signs that fuel pump was stuck | B |
|
| ||||
| A | ||
| ||
| 15.CHECK FREEZE FRAME DATA |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Suspected Area | Proceed to | |||
| Coolant Temp, Ambient Temp for A/C, Intake Air | Coolant Temp, Ambient Temp for A/C | Long FT | Engine Speed | ||
| Difference between Coolant Temp, Ambient Temp for A/C and Intake Air is 10°C or more | Coolant Temp is 125°C or higher, or below Ambient Temp for A/C*1 by 15°C or more | - | - | Engine coolant temperature sensor | A |
| Other than above | -15% or less, or +15% or more | - |
| B | |
| -15 to +15% | Minimum speed is 300 rpm or more*2 | Engine assembly | C | ||
| Minimum speed is less than 300 rpm |
| D | |||
| Difference between Coolant Temp, Ambient Temp for A/C and Intake Air is less than 10°C | - | -15% or less, or +15% or more | - |
| B |
| -15 to +15% | Minimum speed is 300 rpm or more* | Engine assembly | C | ||
| Minimum speed is less than 300 rpm |
| D | |||
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 16.INSPECT FUEL INJECTOR ASSEMBLY |
Check that no carbon is stuck to the fuel injector assembly.
|
| ||||
| OK | |
| 17.CHECK FUEL SYSTEM |
Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter, and inside the fuel tank), and for signs that the fuel pump was stuck.
| Result | Proceed to |
| There is foreign matter or signs that fuel pump was stuck | A |
| There is no foreign matter and no signs that fuel pump was stuck | B |
|
| ||||
| A | ||
| ||
| 18.CHECK FREEZE FRAME DATA |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Coolant Temp | Engine coolant temperature is 40°C or less*1 | Fuel pressure regulator assembly | A |
| Engine coolant temperature is 40 to 90°C*2 | Fuel injector assembly | B | |
| Engine coolant temperature is 90°C or higher*3 | Fuel pressure regulator assembly | A |
|
| ||||
| A | |
| 19.CHECK FUEL PRESSURE |
Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.
| Result | Proceed to |
| Normal | A |
| Abnormal | B |
|
| ||||
|
| ||||
| 20.CHECK FUEL INJECTOR ASSEMBLY |
Clean the inside of the surge tank with compressed air.
After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.
| Result | Proceed to |
| 4000 ppm or more | A |
| Less than 4000 ppm | B |
|
| ||||
| A | |
| 21.CHECK FUEL INJECTOR ASSEMBLY |
Inspect the fuel injector assemblies (Click here).
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | ||
| ||
| 22.CHECK THROTTLE BODY WITH MOTOR ASSEMBLY |
Check if carbon is in the airflow passage.
| Result | Proceed to |
| Carbon in passage | A |
| No carbon present | B |
|
| ||||
| A | ||
| ||
| 23.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks .
|
| ||||
| OK | |
| 24.PERFORM SIMULATION TEST |
Check if the engine can be started.
| Result | Proceed to |
| Engine can be started | A |
| Engine cannot be started | B |
|
| ||||
| A | ||
| ||
| 25.CONFIRM PROBLEM SYMPTOM |
Confirm the problem symptoms.
| Problem Symptom | Suspected Area | Proceed to |
| The engine does not crank |
| A |
| Abnormal cranking speed |
| B |
| There is no initial combustion (combustion does not occur even once)*1 |
| C |
| The engine stalls after starter turnoff (engine stalls immediately after the first time the engine speed increases)*2 |
| D |
| The initial combustion and starter turnoff occur late*3 |
| E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 26.PERFORM SIMULATION TEST |
When cranking the engine, check for a noise indicating that the starter pinion gear is extending, and check that the starter pinion gear is not spinning freely.
| Problem Symptom | Suspected Area | Proceed to |
| A noise indicating that the starter pinion gear is extending is heard and the starter pinion gear is not spinning freely* |
| A |
| A noise indicating that the starter pinion gear is extending is heard but the starter pinion gear is spinning freely |
| B |
| A noise indicating that the starter pinion gear is extending is not heard |
| C |
|
| ||||
|
| ||||
| A | |
| 27.INSPECT BATTERY |
Inspect the battery .
|
| ||||
| OK | |
| 28.CHECK ENGINE ASSEMBLY |
Check that the crankshaft rotates smoothly when rotating it by hand.
|
| ||||
| OK | ||
| ||
| 29.CHECK STARTER ASSEMBLY |
Remove the starter assembly (for 1.4 kW Type) (Click here).
Remove the starter assembly (for 1.6 kW Type) (Click here).
Check for starter pinion gear wear and damage.
|
| ||||
| OK | ||
| ||
| 30.INSPECT BATTERY |
Inspect the battery .
|
| ||||
| OK | |
| 31.INSPECT STARTER ASSEMBLY |
Inspect the starter assembly (for 1.4 kW Type) (Click here).
Inspect the starter assembly (for 1.6 kW Type) (Click here).
|
| ||||
| OK | ||
| ||
| 32.PERFORM SIMULATION TEST |
Check the cranking speed.
| Problem Symptom | Suspected Area | Proceed to |
| Cranking speed is slow (100 rpm or less) |
| A |
| Cranking speed is fast (300 rpm or more)* | Engine compression loss | B |
|
| ||||
| A | |
| 33.INSPECT BATTERY |
Inspect the battery .
|
| ||||
| OK | |
| 34.CHECK ENGINE ASSEMBLY |
Check that the crankshaft rotates smoothly when rotating it by hand.
|
| ||||
| OK | ||
| ||
| 35.CHECK FUEL INJECTOR ASSEMBLY |
Using a sound scope or screwdriver, check for fuel injector operating noise while cranking the engine.
|
| ||||
| OK | |
| 36.CHECK FUEL PRESSURE |
Inspect the fuel pressure .
|
| ||||
| OK | |
| 37.CHECK SPARK PLUG AND SPARK |
Check for sparks .
|
| ||||
| OK | |
| 38.CONFIRM VEHICLE CONDITION |
Confirm the conditions present when the malfunction occurred based on the customer problem analysis.
| Problem Symptom | Suspected Area | Proceed to |
| When the engine is stopped and a long time has passed, engine starting trouble occurs*1 | Fuel pressure regulator is stuck open | A |
| When the engine is stopped and approximately 15 to 120 minutes have passed, engine starting trouble occurs*2 | Fuel injector leak | B |
| When the engine is stopped and approximately 2 to 3 minutes have passed, engine starting trouble occurs*3 | Failure of fuel pressure regulator to maintain fuel pressure | A |
| Condition other than above, or there is an inconsistency in the conditions present when engine starting trouble occurs | - | C*4 |
|
| ||||
|
| ||||
| A | |
| 39.CHECK FUEL PRESSURE |
Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.
| Result | Proceed to |
| 147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine) | A* |
| Below 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine) | B |
|
| ||||
|
| ||||
| 40.CHECK FUEL INJECTOR ASSEMBLY |
After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.
| Result | Proceed to |
| 4000 ppm or more | A |
| Less than 4000 ppm | B* |
|
| ||||
| A | ||
| ||
| 41.CHECK SPARK PLUG |
Inspect the spark plugs .
|
| ||||
| OK | |
| 42.READ VALUE USING TECHSTREAM (ENGINE SPEED) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
Start the engine.
While running the engine, read the value of Engine Speed.
|
| ||||
| OK | |
| 43.CHECK TERMINAL VOLTAGE (IGNITION COIL POWER SOURCE) |
Check the harnesses and connectors, referring to DTC P0351 inspection procedure .
|
| ||||
| OK | |
| 44.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM) |
Check the harnesses and connectors, referring to DTC P0351 inspection procedure .
|
| ||||
| OK | ||
| ||
| 45.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP / SPEED) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for an operating sound from the fuel pump.
| Control the Fuel Pump / Speed | Specified Condition |
| ON | Operating sound heard |
| OFF | Operating sound not heard |
|
| ||||
| OK | |
| 46.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP / SPEED) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for fuel leakage from the fuel pipes.
| Result | Proceed to |
| Fuel leakage or signs of fuel leakage are present | A |
| No fuel leakage or signs of fuel leakage | B |
|
| ||||
| A | ||
| ||
| 47.READ VALUE USING TECHSTREAM (ENGINE SPEED) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
Start the engine.
While running the engine, read the value of Engine Speed.
|
| ||||
| OK | |
| 48.CHECK TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE) |
Check the harnesses and connectors, referring to DTC P0300 inspection procedure .
|
| ||||
| OK | ||
| ||
| 49.CHECK MASS AIR FLOW METER |
Connect the Techstream to the DLC3.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Check MAF in the Data List during idling.
|
| ||||
| OK | |
| 50.CHECK INTAKE SYSTEM |
Check for air leakage in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.] .
|
| ||||
| OK | |
| 51.CHECK THROTTLE BODY WITH MOTOR ASSEMBLY |
Disconnect the throttle body with motor assembly connector.
Crank the engine and check that it starts.
| Result | Proceed to |
| Engine starts | A |
| Engine does not start | B |
Connect the throttle body with motor assembly connector.
|
| ||||
| A | |
| 52.CHECK THROTTLE BODY WITH MOTOR ASSEMBLY |
Check if carbon is in the airflow passage.
|
| ||||
| OK | |
| 53.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE VVT SYSTEM) |
![]() |
Connect the Techstream to the DLC3.
Turn the Techstream on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).
Check the engine speed while operating the camshaft timing oil control valve using the Techstream.
| Tester Operation | Specified Condition |
| OFF | Normal engine speed |
| ON | Soon after camshaft timing oil control valve switched from OFF to ON, engine idles roughly or stalls |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | ||
| ||
| 54.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE VVT EXHAUST LINEAR) |
Connect the Techstream to the DLC3.
Turn the Techstream on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank1) or Control the VVT Exhaust Linear (Bank2).
Check the engine speed while operating the camshaft timing oil control valve using the Techstream.
| Tester Operation | Specified Condition |
| 0% | Normal engine speed |
| 100% | Engine idles roughly or stalls |
|
| ||||
|
| ||||
| 55.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Check the harnesses and connectors, referring to DTC P0102 inspection procedure .
|
| ||||
| OK | ||
| ||
| 56.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor (Click here).
|
| ||||
| OK | |
| 57.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) |
Check the harnesses and connectors, referring to DTC P0115 inspection procedure .
|
| ||||
| OK | |
| 58.CHECK MASS AIR FLOW METER |
Connect the Techstream to the DLC3.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Check MAF in the Data List during idling.
|
| ||||
| OK | |
| 59.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Check the harnesses and connectors, referring to DTC P0102 inspection procedure .
|
| ||||
| OK | |
| 60.READ VALUE USING TECHSTREAM |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Atmospheric Pressure and Long FT.
| Data List Item | Result | Suspected Area | Proceed to |
| Long FT | +25% or more or less than -25% |
| A |
| Atmosphere Pressure | 80 kPa or less (when elevation is 0 m) | ||
| Both Data List items listed above | Values are other than above | - | B |
|
| ||||
| A | |
| 61.PERFORM SIMULATION TEST |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Value Reset.
Confirm the following conditions as instructed on the screen.
After confirming, select "Next" and initialize the learn value.
After the Techstream display indicates that the learning value reset is complete, turn the ignition switch off and wait for 5 seconds or more.
Check if the engine can be started.
| Result | Proceed to |
| Engine can be started | A |
| Engine cannot be started | B |
|
| ||||
| A | |
| 62.INSPECT AIR FUEL RATIO SENSOR |
![]() |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel System Status #1 and Fuel System Status #2.
Confirm that Fuel System Status #1 and Fuel System Status #2 are both CL.
Enter the following menus: Powertrain / Engine and ECT / Data List / AF Lambda B1S1 and AF Lambda B2S1.
Confirm that AF Lambda B1S1 and AF Lambda B2S1 are both within the range of 0.95 to 1.05 when idling.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.
| Tester Display | Injection Volume | Specified Condition |
| AFS Voltage B1S1 AFS Voltage B2S1 | +12.5% | Air fuel ratio sensor output voltage is below 3.1 V |
| -12.5% | Air fuel ratio sensor output voltage is higher than 3.4 V |
| Result | Proceed to |
| Normal | A |
| Abnormal | B |
|
| ||||
| A | |
| 63.PERFORM SIMULATION TEST |
Check if the idling speed is stable after starting the engine.
|
| ||||
| OK | ||
| ||
| 64.CHECK FUEL PRESSURE |
Inspect the fuel pressure .
|
| ||||
| OK | |
| 65.CHECK SPARK PLUG |
Inspect the spark plugs .
| Result | Proceed to |
| All cylinders are normal | A |
| One cylinder is abnormal*1 | B |
| All cylinders are abnormal*2, *3 | C |
|
| ||||
|
| ||||
| A | |
| 66.CONFIRM VEHICLE CONDITION |
Confirm the conditions present when the malfunction occurred based on the customer problem analysis.
| Problem Symptom | Suspected Area | Proceed to |
| When the engine is stopped and a long time has passed, engine starting trouble occurs*1 | Fuel pressure regulator is stuck open | A |
| When the engine is stopped and approximately 15 to 120 minutes have passed, engine starting trouble occurs*2 | Fuel injector leak | B |
| When the engine is stopped and approximately 2 to 3 minutes have passed, engine starting trouble occurs*3 | Failure of fuel pressure regulator to maintain fuel pressure | A |
| Condition other than above, or there is an inconsistency in the conditions present when engine starting trouble occurs | - | C*4 |
|
| ||||
|
| ||||
| A | |
| 67.CHECK FUEL PRESSURE |
Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.
| Result | Proceed to |
| 147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine) | A* |
| Below 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine) | B |
|
| ||||
|
| ||||
| 68.CHECK FUEL INJECTOR ASSEMBLY |
Clean the inside of the surge tank with compressed air.
After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.
| Result | Proceed to |
| 4000 ppm or more | A |
| Less than 4000 ppm | B* |
|
| ||||
| A | ||
| ||
| 69.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP / SPEED) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for fuel leakage from the fuel pipes.
| Result | Proceed to |
| Fuel leakage or signs of fuel leakage are present | A |
| No fuel leakage or signs of fuel leakage | B |
|
| ||||
| A | ||
| ||
| 70.CHECK MALFUNCTION CONDITION |
If the malfunction could not be identified during the inspections in steps 38, 39, 40 and 46, perform fuel system troubleshooting C (steps 71 to 80).
| Step Performed | Troubleshooting by System | Procedure | Proceed to |
| Steps 38, 39, 40 and 46 | Fuel system troubleshooting C | 71 to 80 | A |
If the malfunction could not be identified during the inspection in step 44, perform ignition system troubleshooting (steps 75 to 80).
| Step Performed | Troubleshooting by System | Procedure | Proceed to |
| Step 44 | Ignition system troubleshooting | 75 to 80 | B |
If the malfunction could not be identified during the inspections in steps 53, 54 and 55, perform intake air system troubleshooting (steps 81 to 83). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 84 to 91).
| Step Performed | Troubleshooting by System | Procedure | Proceed to |
| Step 53, 54, 55 | Intake air system troubleshooting | 81 to 83 | C |
| Fuel system troubleshooting A | 84 to 91 |
If the malfunction could not be identified during the inspections in steps 56, 57, 58, 59, 62, 63, 65, 66, 67, 68 and 69, perform fuel system troubleshooting A (steps 92 to 99), fuel system troubleshooting B (steps 100 to 102), intake air system troubleshooting (steps 103 to 105), and ignition system troubleshooting (steps 106 to 111), in that order.
| Step Performed | Troubleshooting by System | Procedure | Proceed to |
| Steps 56, 57, 58, 59, 62, 63, 65, 66, 67, 68 and 69 | Fuel system troubleshooting A | 92 to 99 | D |
| Fuel system troubleshooting B | 100 to 102 | ||
| Intake air system troubleshooting | 103 to 105 | ||
| Ignition system troubleshooting | 106 to 111 |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 71.INSPECT FUEL INJECTOR ASSEMBLY |
Inspect the fuel injector assemblies (Click here).
|
| ||||
| OK | |
| 72.CHECK TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE) |
Check the harnesses and connectors, referring to DTC P0300 inspection procedure (See page ES-243).
|
| ||||
| OK | |
| 73.CHECK CRANKSHAFT POSITION SENSOR |
Replace the crankshaft position sensor (Click here).
Check the engine start operation.
|
| ||||
| OK | ||
| ||
| 74.CHECK VVT SENSOR |
Replace the VVT sensor (Click here).
Check the engine start operation.
|
| ||||
| OK | ||
| ||
| 75.CHECK CRANKSHAFT POSITION SENSOR |
Check the tightening torque and installation condition of the crankshaft position sensor bolt.
Check the connection of the crankshaft position sensor connector.
|
| ||||
| OK | |
| 76.CHECK VVT SENSOR |
Check the tightening torque and installation condition of the VVT sensor bolt.
Check the connection of the VVT sensor connector.
|
| ||||
| OK | |
| 77.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
Check the harnesses and connectors, referring to DTC P0335 inspection procedure .
|
| ||||
| OK | |
| 78.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM) |
Check the harnesses and connectors, referring to DTC P0340 inspection procedure .
Check the harnesses and connectors, referring to DTC P0365 inspection procedure .
|
| ||||
| OK | |
| 79.CHECK AND REPLACE CRANKSHAFT POSITION SENSOR |
Replace the crankshaft position sensor (Click here).
Check the engine start operation.
|
| ||||
| OK | ||
| ||
| 80.CHECK VVT SENSOR |
Replace the VVT sensor (Click here).
Check the engine start operation.
|
| ||||
| OK | ||
| ||
| 81.READ VALUE USING TECHSTREAM (ISC LEARNING VALUE) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Start the engine and warm it up until the engine coolant temperature stabilizes with the A/C switch and all the accessory switches off.
Enter the following menus: Powertrain / Engine and ECT / Data List / ISC Learning Value.
| Data List Item | Result | Suspected Area | Proceed to |
| ISC Learning Value | (Engine displacement (liters) x 0.9) or more |
| A |
| Less than (engine displacement (liters) x 0.9) | - | B |
|
| ||||
| A | |
| 82.CHECK CYLINDER COMPRESSION PRESSURE |
Inspect the compression .
|
| ||||
| OK | ||
| ||
| 83.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor (Click here).
|
| ||||
| OK | |
| 84.CHECK FUEL PRESSURE |
Attach a fuel pressure gauge and check the fuel pressure when cranking the engine and after stopping the engine.
| Vehicle State | Specified Condition |
| Cranking engine | 281 to 287 kPa (2.87 to 2.93 kgf/cm2) |
| 5 minutes after stopping engine | 147 kPa (1.5 kgf/cm2) or higher |
|
| ||||
| OK | |
| 85.READ VALUE USING TECHSTREAM (LONG FT) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT.
| Data List Item | Result | Suspected Area | Proceed to |
| Long FT | -15 to +15% |
| A |
| +15% or more, or less than -15% | Fuel injector assembly | B |
|
| ||||
| A | |
| 86.PERFORM SIMULATION TEST |
Check if the idling speed is stable after starting the engine and if an unstable idling speed has ever occurred in the past.
| Problem Symptom | Suspected Area | Proceed to |
| Current idling speed unstable or history of unstable idling speed | Crankshaft position sensor system | A |
| All current and past idling speeds are stable | Fuel | B |
|
| ||||
| A | |
| 87.CHECK CRANKSHAFT POSITION SENSOR |
Check the tightening torque and installation condition of the crankshaft position sensor bolt.
Check the connection of the crankshaft position sensor connector.
|
| ||||
| OK | |
| 88.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
Check the harnesses and connectors, referring to DTC P0335 inspection procedure .
|
| ||||
| OK | |
| 89.CHECK CRANKSHAFT POSITION SENSOR |
Replace the crankshaft position sensor (Click here).
Check the engine start operation.
|
| ||||
| OK | ||
| ||
| 90.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP / SPEED) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for fuel leakage from the fuel pipes.
| Result | Proceed to |
| Fuel leakage or signs of fuel leakage are present | A |
| No fuel leakage or signs of fuel leakage | B |
|
| ||||
| A | ||
| ||
| 91.INSPECT FUEL PUMP |
Inspect the fuel pump .
|
| ||||
| OK | ||
| ||
| 92.CHECK FUEL PRESSURE |
Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.
| Result | Proceed to |
| 147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine) | A |
| Below 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine) | B |
|
| ||||
| A | |
| 93.READ VALUE USING TECHSTREAM (LONG FT) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT.
| Data List Item | Result | Suspected Area | Proceed to |
| Long FT | -15 to +15% |
| A |
| +15% or more, or less than -15% | Fuel injector assembly | B |
|
| ||||
| A | |
| 94.PERFORM SIMULATION TEST |
Check if the idling speed is stable after starting the engine and if an unstable idling speed has ever occurred in the past.
| Problem Symptom | Suspected Area | Proceed to |
| Current idling speed unstable or history of unstable idling speed | Crankshaft position sensor system | A |
| All current and past idling speeds are stable | Fuel | B |
|
| ||||
| A | |
| 95.CHECK CRANKSHAFT POSITION SENSOR |
Check the tightening torque and installation condition of the crankshaft position sensor bolt.
Check the connection of the crankshaft position sensor connector.
|
| ||||
| OK | |
| 96.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
Check the harnesses and connectors, referring to DTC P0335 inspection procedure .
|
| ||||
| OK | |
| 97.CHECK CRANKSHAFT POSITION SENSOR |
Replace the crankshaft position sensor (Click here).
Check the engine start operation.
|
| ||||
| OK | ||
| ||
| 98.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP / SPEED) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for fuel leakage from the fuel pipes.
| Result | Proceed to |
| Fuel leakage or signs of fuel leakage are present | A |
| No fuel leakage or signs of fuel leakage | B |
|
| ||||
| A | ||
| ||
| 99.INSPECT FUEL PUMP |
Inspect the fuel pump (Click here).
|
| ||||
| OK | |
| 100.CHECK PURGE VSV |
![]() |
Disconnect the vacuum hose (on the canister side) of the purge VSV.
Start the engine.
Idle the engine.
Disconnect the connector of the purge VSV.
Check if air flows through the purge VSV.
Connect the connector of the purge VSV.
Connect the vacuum hose of the purge VSV.
|
| ||||
| OK | |
| 101.CHECK FUEL INJECTOR ASSEMBLY |
Clean the inside of the surge tank with compressed air.
After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.
| Result | Proceed to |
| 4000 ppm or more | A |
| Less than 4000 ppm | B |
|
| ||||
| A | ||
| ||
| 102.CHECK INTAKE VALVE |
Check if carbon is on the intake valves.
| Result | Proceed to |
| Carbon present | A |
| No carbon present | B |
|
| ||||
| A | ||
| ||
| 103.READ VALUE USING TECHSTREAM (ISC LEARNING VALUE) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.
Enter the following menus: Powertrain / Engine and ECT / Data List / ISC Learning Value.
| Data List Item | Result | Suspected Area | Proceed to |
| ISC Learning Value | (Engine displacement (liters) x 0.9) or more |
| A |
| Less than (engine displacement (liters) x 0.9) | - | B |
|
| ||||
| A | |
| 104.CHECK CYLINDER COMPRESSION PRESSURE |
Inspect the compression .
|
| ||||
| OK | ||
| ||
| 105.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor .
|
| ||||
| OK | |
| 106.CHECK CRANKSHAFT POSITION SENSOR |
Check the tightening torque and installation condition of the crankshaft position sensor bolt.
Check the connection of the crankshaft position sensor connector.
|
| ||||
| OK | |
| 107.CHECK VVT SENSOR |
Check the tightening torque and installation condition of the VVT sensor bolt.
Check the connection of the VVT sensor connector.
|
| ||||
| OK | |
| 108.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
Check the harnesses and connectors, referring to DTC P0335 inspection procedure .
|
| ||||
| OK | |
| 109.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM) |
Check the harnesses and connectors, referring to DTC P0340 inspection procedure .
Check the harnesses and connectors, referring to DTC P0365 inspection procedure .
|
| ||||
| OK | |
| 110.CHECK CRANKSHAFT POSITION SENSOR |
Replace the crankshaft position sensor (Click here).
Check the engine start operation.
|
| ||||
| OK | ||
| ||
| 111.CHECK VVT SENSOR |
Replace the VVT sensor (Click here).
Check the engine start operation.
|
| ||||
| OK | ||
| ||