Home › Drivetrain › K320 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (When Using the Engine Support Bridge) › 2020.08–2021.07
RM3700E _52 Drivetrain _092906 K320 MULTIDRIVE / CVT _0438045 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge) A

K320 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C444244N04
4.125,3.906 4.292,3.906 4.292,3.906 4.458,3.708 false 6.406,0.26 6.823,0.26 false 6.083,5.417 6.25,5.417 6.25,5.417 6.583,5 false 6.198,3.635 6.031,3.635 6.031,3.635 5.865,3.427 false 3.833,4.25 3.667,4.25 3.667,4.25 3.5,4.583 false 1.375,2.24 1.542,2.24 1.542,2.24 1.708,2.042 false 1.135,0.885 1.552,0.885 false 6.458,0.656 6.792,0.656 false 6.479,1.021 6.813,1.021 false 1.625,0.74 1.906,1.094 0.281,0.354 18 false 9 6.271,3.479 6.552,3.833 0.281,0.354 18 false 8 3.875,4.115 4.156,4.469 0.281,0.354 18 false 5 1.219,2.073 1.5,2.427 0.281,0.354 18 false 7 6,0.125 6.458,0.51 0.458,0.385 18 false 1, 3 6.292,0.521 6.573,0.875 0.281,0.354 18 false 2 3.146,5.458 3.458,5.656 0.313,0.198 10 false x4 3.406,5.354 3.719,5.552 0.313,0.198 10 false x4 3.865,5.271 4.177,5.469 0.313,0.198 10 false x9 5.167,3.448 5.479,3.646 0.313,0.198 10 false x2 1.573,1.177 1.885,1.375 0.313,0.198 10 false x2 5.917,5.292 6.198,5.646 0.281,0.354 18 false 4 3.948,3.76 4.229,4.115 0.281,0.354 18 false 6 5.781,0.896 6.885,1.26 1.104,0.365 18 false 10, 11

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 ALIGN FRONT WHEELS FACING STRAIGHT AHEAD - (Click here) - -
4 FRONT WHEELS - - - -
5 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -
6 ENGINE UNDER COVER LH 51442C - - -
7 ENGINE UNDER COVER RH 51441C - - -
8 FRONT FENDER LINER LH 53876A - - -
9 FRONT FENDER LINER RH 53875A - - -
10 DRAIN ENGINE COOLANT - - (Click here) -
11 DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID - - (Click here) -

C444245N04
1.313,2.583 1.646,2.583 false 1.302,3.198 1.635,3.198 false 1.396,4.031 1.729,4.031 false 2.281,3.292 2.698,3.292 false 2.875,0.75 3.208,0.75 false 4.24,1.375 4.573,1.375 false 5.094,1.885 5.427,1.885 false 5.729,1.354 6.063,1.354 false 4.688,2.688 4.854,2.521 4.854,2.521 5.021,2.521 false 5.969,3.406 6.135,3.406 6.135,3.406 6.302,3.24 false 2.823,2.604 3.156,2.604 false 3.271,0.604 3.823,0.958 0.552,0.354 18 false 12 4.615,1.229 5.167,1.583 0.552,0.354 18 false 13 5.49,1.74 6.042,2.094 0.552,0.354 18 false 14 5.104,2.375 5.656,2.729 0.552,0.354 18 false 15 1.708,2.438 2.26,2.792 0.552,0.354 18 false 16 1.698,3.052 2.25,3.406 0.552,0.354 18 false 17 1.792,3.896 2.344,4.25 0.552,0.354 18 false 18 5.406,1.198 5.958,1.552 0.552,0.354 18 false 19 5.677,3.25 6.229,3.604 0.552,0.354 18 false 20 3.042,3.167 3.594,3.521 0.552,0.354 18 false 21 3.26,2.521 3.417,2.719 0.156,0.198 10 false ● 6.521,2.333 6.927,2.625 0.406,0.292 10 false x3

Procedure Part Name Code
Z101186

Z101188

Z101187

12 WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY - - - -
13 FRONT NO. 1 VENTILATOR SEAL 55815E - - -
14 WATER GUARD PLATE LH 55735A - - -
15 OUTER COWL TOP PANEL SUB-ASSEMBLY 55701J - - -
16 AIR CLEANER CAP WITH AIR CLEANER HOSE - - - -
17 AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY 17801 - - -
18 AIR CLEANER CASE SUB-ASSEMBLY 17701 - - -
19 ECM 89661 - - -
20 BATTERY CLAMP SUB-ASSEMBLY 74404A - - -
21 TRANSMISSION CONTROL CABLE ASSEMBLY 33820B (Click here) - -

● Non-reusable part - -

C428846N05
2.667,1.083 3.083,1.083 false 4.708,1.833 5.042,1.833 false 5.948,4.583 6.365,4.583 false 1.552,5.167 1.885,5.167 false 0.865,4.75 1.198,4.75 false 1.26,3.906 1.594,3.906 false 4.635,1.281 4.948,1.479 0.313,0.198 10 false x2 6.26,4.979 6.552,5.115 0.292,0.135 10 false x2 3.469,0.958 4.021,1.313 0.552,0.354 18 false 22 5.094,1.688 5.646,2.042 0.552,0.354 18 false 26 6.729,4.438 7.042,4.781 0.313,0.344 18 false 23 1.24,5.01 1.583,5.344 0.344,0.333 18 false 24 0.542,4.635 0.885,4.979 0.344,0.344 18 false 27 0.948,3.76 1.26,4.104 0.313,0.344 18 false 25

Procedure Part Name Code
Z101186

Z101188

Z101187

22 ENGINE WIRE 82121 (Click here) - -
23 TCM 89535B (Click here) - -
24 NO. 4 WATER BY-PASS HOSE 16281N - - -
25 NO. 3 WATER BY-PASS HOSE ASSEMBLY 16290F - - -
26 NO. 1 TRANSMISSION CONTROL CABLE BRACKET 33823 - - -
27 STARTER ASSEMBLY 28100 - - -

C449798N01
3.927,0.5 4.25,0.5 false 6.417,0.25 6.75,0.25 false 1.083,3.75 1.5,3.75 false 4.135,2.25 4.135,2.615 false 1.167,1.885 1.49,1.885 false 5.865,0.49 6.188,0.49 false 2.135,1.083 2.458,1.083 false 5.938,1.844 6.177,2.042 0.24,0.198 10 false x2 6.125,1.344 6.333,1.5 0.208,0.156 10 false x2 2.115,3.094 2.354,3.313 0.24,0.219 10 false x2 1.688,2.708 1.927,2.906 0.24,0.198 10 false x2 1.531,1.781 1.844,1.938 0.313,0.156 10 false ● 2.906,3.938 3.146,4.156 0.24,0.219 10 false x2 2.104,4.365 2.344,4.583 0.24,0.219 10 false x2 5.76,0.406 6.073,0.563 0.313,0.156 10 false ● 6.115,0.125 6.51,0.583 0.396,0.458 18 false 28 4.281,0.375 4.677,0.833 0.396,0.458 18 false 29 1.833,0.948 2.229,1.406 0.396,0.458 18 false 30 0.813,3.625 1.208,4.083 0.396,0.458 18 false 31 4.177,2.667 4.573,3.125 0.396,0.458 18 false 32

Procedure Part Name Code
Z101186

Z101188

Z101187

28 SECURE STEERING WHEEL - (Click here) - -
29 COLUMN HOLE COVER SILENCER SHEET 45259A - - -
30 NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY 45260 - - -
31 CENTER NO. 4 ENGINE UNDER COVER 51447D - - -
32 FRONT EXHAUST PIPE ASSEMBLY 17410 (Click here) - -

● Non-reusable part - -

C444247N03
0.417,2.5 1.25,2.667 0.833,0.167 0.375,2.458 1.292,2.708 0.917,0.25 5.771,1.552 6.604,1.719 0.833,0.167 5.729,1.51 6.646,1.76 0.917,0.25 2.917,4.583 3.25,4.583 false 1.167,1.781 1.333,1.781 1.333,1.781 1.5,1.948 false 0.833,2.167 0.833,2.5 false 1.396,0.865 1.729,0.865 false 6.396,0.219 6.813,0.219 false 4.552,1.635 4.552,1.885 false 5.438,1.635 5.771,1.635 false 5.76,4.458 6.177,4.458 false 4.979,2.719 5.313,2.719 false 3.531,4.969 3.844,5.167 0.313,0.198 10 false x3 4.229,5.146 4.542,5.344 0.313,0.198 10 false x2 5.333,5.24 5.646,5.438 0.313,0.198 10 false x2 5.792,5 6.104,5.198 0.313,0.198 10 false x2 5.479,1.635 5.792,1.833 0.313,0.198 10 false x2 0.927,2.156 1.24,2.354 0.313,0.198 10 false x2 0.521,2.51 1.844,2.906 1.323,0.396 8 false 43 (438, 32) 2.208,4.458 2.958,4.813 0.75,0.354 18 false 36, 38 6.469,4.333 6.792,4.667 0.323,0.333 18 false 37 0.833,1.667 1.156,2 0.323,0.333 18 false 34 4.573,1.875 4.896,2.208 0.323,0.333 18 false 34 5.677,0.083 6.833,0.396 1.156,0.313 18 false 35, 39 1.781,0.729 2.104,1.063 0.323,0.333 18 false 33 5.021,5.073 5.333,5.271 0.313,0.198 10 false x2 3.896,5.458 4.208,5.656 0.313,0.198 10 false x2 5.344,2.594 5.667,2.927 0.323,0.333 18 false 33 5.896,1.563 6.646,1.875 0.75,0.313 8 false 43 (438, 32)

Procedure Part Name Code
Z101186

Z101188

Z101187

33 FRONT DRIVE SHAFT ASSEMBLIES - - - -
34 ENGINE HANGERS - (Click here) - -
35 ENGINE SUPPORT BRIDGE - (Click here) - -
36 NO. 2 ENGINE MOVING CONTROL ROD 12364B - - -
37 FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY 51201 (Click here) - -
38 NO. 2 ENGINE MOVING CONTROL ROD 12364B - - -
39 SUPPORT CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY 30400 (Click here) - -

C446856N03
2.563,3.115 2.729,3.115 2.729,3.115 2.802,2.656 false 2.26,2.948 2.813,3.302 0.552,0.354 18 false 40

Procedure Part Name Code
Z101186

Z101188

Z101187

40 MANIFOLD STAY 17118 (Click here) - -

C432956N04
3.5,1.365 3.75,0.583 3.75,0.583 3.917,0.583 false 5.896,1.833 6.229,1.833 false 3.802,3.25 4.052,2.688 4.052,2.688 4.219,2.688 false 3.979,2.292 4.313,2.292 false 2.979,3.438 2.75,3.667 2.75,3.667 2.75,3.833 false 5.771,4.25 6.188,4.25 false 4.25,0.521 4.406,0.719 0.156,0.198 10 false ★ 4.438,0.448 4.99,0.802 0.552,0.354 18 false 42 6.271,1.688 6.823,2.042 0.552,0.354 18 false 43 4.385,2.135 4.938,2.49 0.552,0.354 18 false 41 4.75,2.563 5.302,2.917 0.552,0.354 18 false 46 4.583,2.656 4.792,2.833 0.208,0.177 10 false ● 2.823,3.885 3.375,4.24 0.552,0.354 18 false 45 6.531,4.115 7.01,4.469 0.479,0.354 18 false 44 1.104,3.542 1.417,3.74 0.313,0.198 10 false x5 3.615,1.344 3.927,1.542 0.313,0.198 10 false *a 5.031,1.208 5.344,1.406 0.313,0.198 10 false x3 5.823,1.063 6.135,1.26 0.313,0.198 10 false x4

Procedure Part Name Code
Z101186

Z101188

Z101187

41 FLYWHEEL HOUSING UNDER COVER 11361J - - -
42 DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT 32101G (Click here) - -
43 ENGINE MOUNTING INSULATOR LH 12372A - - -
44 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY 30400 (Click here) - -
45 TORQUE CONVERTER ASSEMBLY 32000A (Click here) - -
46 CVT OIL PUMP TYPE T OIL SEAL 30400E (Click here) - -

*a BLACK COLOR: x1
SILVER COLOR: x5
- -
● Non-reusable part ★ Precoated part

C446826N06
3.896,0.417 7.083,1.5 3.188,1.083 5.417,1.5 5.417,0.417 false 5.021,0.677 4.688,0.677 false 6.302,0.656 5.969,0.656 false 4,1.948 3.667,1.948 false 2.833,2.25 2.5,2.25 false 1.531,4.583 1.198,4.583 false 6.792,0.25 6.458,0.25 false 6.333,1.156 6,1.156 false 3.969,0.469 4.344,0.708 0.375,0.24 12 false *A 5.542,0.469 5.917,0.708 0.375,0.24 12 false *B 6.375,0.5 6.927,0.854 0.552,0.354 18 false 48 5.75,0.083 6.5,0.417 0.75,0.333 18 false 49, 50 4.063,1.792 4.615,2.146 0.552,0.354 18 false 47 2.198,2.115 2.75,2.469 0.552,0.354 18 false 47 0.885,4.438 1.438,4.792 0.552,0.354 18 false 47 6.417,1.094 6.573,1.292 0.156,0.198 10 false ● 4.354,0.5 4.906,0.854 0.552,0.354 18 false 48

Procedure Part Name Code
Z101186

Z101188

Z101187

47 WIRE HARNESS CLAMP BRACKET - - - -
48 TRANSMISSION CASE PLUG ASSEMBLY 35150B - - -
49 INSPECT TORQUE CONVERTER ASSEMBLY 32000A (Click here) - -
50 INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY 32101B (Click here) - -

*A for Type A *B for Type B
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the continuously variable transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

Air intake system parts

·

Exhaust system parts


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of continuously variable transaxle assembly
1.

Reset memory

2.

Transaxle compensation code (Input)

3.

CVT oil pressure calibration


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Front wheel alignment adjustment Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)

CAUTION:
·
C313282C01
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Heavy object exceeding the capacity of the transmission jack


Because the continuously variable transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the transmission jack could drop and components could fall down.


·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 3.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 4.REMOVE FRONT WHEELS

Hide 51410 5.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51442C 6.REMOVE ENGINE UNDER COVER LH

Hide 51441C 7.REMOVE ENGINE UNDER COVER RH

Hide 53876A 8.SEPARATE FRONT FENDER LINER LH

Hide 53875A 9.SEPARATE FRONT FENDER LINER RH

Hide 10.DRAIN ENGINE COOLANT

Hide 11.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 12.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55815E 13.REMOVE FRONT NO. 1 VENTILATOR SEAL

Hide 55735A 14.REMOVE WATER GUARD PLATE LH

Hide 55701J 15.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 16.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17801 17.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 18.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 20.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 33820B 21.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Z101186

Click here(Click here)

Hide 82121 22.DISCONNECT ENGINE WIRE

a.
C428822C08
2.583,0.208 2.76,0.375 0.177,0.167 10 true *1 2.885,0.792 3.073,0.958 0.188,0.167 10 true *2 2.896,1.26 3.083,1.417 0.188,0.156 10 true *3 3.729,0.719 3.917,0.875 0.188,0.156 10 true *4 3.073,1.844 3.26,2.021 0.188,0.177 10 true *5 4.375,1.813 4.563,1.979 0.188,0.167 10 true *6 2.635,2.594 2.823,2.76 0.188,0.167 10 true *7 2.167,2.271 2.354,2.427 0.188,0.156 10 true *8 0.469,0.135 0.896,0.479 0.427,0.344 18 false i, ii
*1 Transmission Wire Connector *2 Shift Stroke Sensor Connector
*3 Park/Neutral Position Switch Connector *4 Transmission Revolution Sensor (NOUT) Connector
*5 TCM Connector *6 Transmission Revolution Sensor (NSS) Connector
*7 Oil Pressure Sensor Connector *8 Transmission Revolution Sensor (NT) Connector
V113147

Remove in this Direction - -


i.

Disconnect all the clamps and connectors and remove the engine wire from the engine assembly with transaxle.


ii.

Remove the bolt.



b.
C431049N04
0.25,0.156 0.531,0.51 0.281,0.354 18 false i 3.542,0.198 4.073,0.563 0.531,0.365 18 true ii, iii 1.844,2.719 2.125,3.073 0.281,0.354 18 false iv

i.

Disconnect the No. 3 water by-pass hose assembly.


ii.

Disengage the 3 clamps.


iii.

Remove the bolt to disconnect the engine wire from the continuously variable transaxle assembly.


iv.

Disengage the 3 clamps to disconnect the engine wire from the front suspension crossmember sub-assembly.



Hide 89535B 23.REMOVE TCM

Z101186

NOTICE:

To prevent coolant from entering the TCM through its connector portion, be sure to remove the TCM before disconnecting any of the coolant system hoses.



a.
C431050


Hide 16281N 24.DISCONNECT NO. 4 WATER BY-PASS HOSE

Hide 16290F 25.DISCONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY

Hide 33823 26.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C431052


Hide 28100 27.REMOVE STARTER ASSEMBLY

Hide 45259A 29.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 30.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 51447D 31.REMOVE CENTER NO. 4 ENGINE UNDER COVER

Hide 17410 32.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Z101186

Click here(Click here)

Hide 35.INSTALL ENGINE SUPPORT BRIDGE

a.
C430497C02
5.26,0.813 4.958,0.552 true 5.135,0.958 4.813,0.958 true 1.885,0.865 1.458,0.365 true 1.271,0.25 1.479,0.427 0.208,0.177 10 true *a 4.594,0.875 4.792,1.052 0.198,0.177 10 true *b 4.75,0.458 4.958,0.635 0.208,0.177 10 true *c 0.458,0.104 0.604,0.396 0.146,0.292 18 true i
*a Existing Hole *b Protective Tape
*c Bolt - -


i.

Cover the existing holes in the left and right suspension tower with protective tape, then use a thin-bladed screwdriver to make holes in the tape, and insert the 2 bolts for setting the sub-beam of the engine support bridge.

Item Part No.
Bolt 9010-10226



b.
C444252C02
1.021,1.604 1.333,1.313 true 6.073,1.229 5.771,0.958 true 1.823,5.375 1.573,5.156 true 5.031,5.01 5.292,4.813 true 1.656,4.271 1.365,4.313 true 5.688,4.177 5.396,4.219 true 1.698,4.177 1.875,4.344 0.177,0.167 10 true *a 1.823,5.354 2.01,5.51 0.188,0.156 10 true *b 0.833,1.583 1.021,1.792 0.188,0.208 10 true *c 0.427,0.125 0.656,0.646 0.229,0.521 18 false i 6.073,1.177 6.26,1.385 0.188,0.208 10 true *c 4.833,5 5.021,5.156 0.188,0.156 10 true *b 5.208,4.135 5.385,4.302 0.177,0.167 10 true *a
*a Support Shaft *b Front Side Member
*c Front Suspension Nut - -


i.

Install SST to the vehicle body as shown in the illustration.

SST
09940-10010  

CAUTION:
·
C330755C01
0.448,1.167 0.781,1.167 false 2.438,1.167 2.771,1.167 false 1.052,1.781 1.052,1.448 1.052,1.448 1.219,1.448 false 2.604,1.781 2.604,1.448 2.604,1.448 2.438,1.448 false 0.292,1.094 0.604,1.25 0.313,0.156 10 false *a 2.271,1.094 2.583,1.25 0.313,0.156 10 false *a 1.281,1.385 1.594,1.542 0.313,0.156 10 false *b 2.271,1.385 2.583,1.542 0.313,0.156 10 false *b
*a Support Shaft
*b Front Side Member


Make sure that no oil or grease is on the front side member, and set the support shaft on the level surface of the front side member.

·

The engine support bridge may fall off if any oil or grease is still on or it is installed on the unlevel surface.



NOTICE:
·

Prevent SST from contacting the vehicle body exterior and windshield glass.

·

To prevent damage to the engine hood, place pieces of cloth between the engine hood and SST.

·

Lightly shake SST by hand to make sure it is securely installed before performing work.





c.
C430498C01
3.052,1.75 3.469,1.75 false 3.021,2 3.438,2 false 2.885,2.25 2.583,2 false 2.552,1.208 2.25,0.958 false 3.51,1.656 3.823,1.813 0.313,0.156 10 false *a 2.052,0.885 2.365,1.042 0.313,0.156 10 false *b 2.385,1.917 2.698,2.073 0.313,0.156 10 false *c 3.479,1.927 3.792,2.083 0.313,0.156 10 false *d 0.49,0.094 0.771,0.448 0.281,0.354 18 false i
*a Support Shaft *b Sub Beam
*c Front Side Member *d Threaded Portion


i.

Turn the threaded portion of each support shaft to adjust its height until the sub beams are parallel to the ground.



d.
C444253C03
0.458,0.271 1.375,0.271 false 1.063,1.479 1.396,1.479 true 1.479,1.573 1.792,1.615 true 1.667,0.667 2,0.583 false 2.042,0.5 2.354,0.656 0.313,0.156 10 false *a 0.292,0.198 0.604,0.354 0.313,0.156 10 false *b 0.865,1.406 1.031,1.594 0.167,0.188 10 true *c 1.823,1.552 1.99,1.719 0.167,0.167 10 true *d 3.271,0.094 3.896,0.406 0.625,0.313 18 false i, ii
*a Chain Block *b Sling Bracket
*c Fuse Shackle *d Shackle (A)


i.

Install the chain block to the sling bracket.


ii.

Install the division bar to the chain block with the shackles.

CAUTION:
·
C338949C01
0.458,2.313 0.583,2.313 0.583,2.313 0.875,2.635 false 0.354,2.677 0.479,2.677 0.479,2.677 0.865,2.865 false 2.177,2.271 2.302,2.271 2.302,2.271 2.604,2.594 false 2.073,2.656 2.198,2.656 2.198,2.656 2.583,2.844 false 0.281,2.208 0.604,2.469 0.323,0.26 10 false *a 0.167,2.573 0.51,2.844 0.344,0.271 10 false *b 1.99,2.156 2.313,2.417 0.323,0.26 10 false *a 1.885,2.542 2.229,2.813 0.344,0.271 10 false *b
*a Fuse Shackle
*b Shackle (A)


Make sure the fuse shackle is on the chain block side and the shackle (A) is on the division bar side as shown in the illustration so that the fuse bolt is visible and can be checked for deformation easily.

·

If the fuse shackle is installed upside down, deformation of the fuse bolt will not be visible and cannot be used to tell if the load capacity of the engine support bridge has been exceeded. If the load capacity is exceeded, it may cause the engine support bridge to damage the vehicle and the engine assembly with continuously variable transaxle assembly may fall.

·
C330757C01
2.75,1 3.083,1 false 1.01,1 1.344,1 false 0.917,1.417 1.333,1.583 true 2.635,1.396 3.083,1.583 true 1.396,0.917 1.708,1.073 0.313,0.156 10 false *a 1.385,1.51 1.698,1.667 0.313,0.156 10 false *b 3.125,0.917 3.354,1.083 0.229,0.167 10 false *a 3.135,1.5 3.354,1.667 0.219,0.167 10 false *b
*a Fuse Shackle
*b Fuse Bolt


Make sure that the fuse bolt of the fuse shackle is free of damage, such as deformation or cracks. If damaged, replace the fuse shackle.

·

If a deformed fuse bolt is used, it cannot be used to tell if the load capacity of the engine support bridge has been exceeded. If the load capacity is exceeded, it may cause the engine support bridge to damage the vehicle and the engine assembly with transaxle assembly may fall.





e.
C446020C02
1.885,0.448 2.313,0.542 true 1.792,0.927 1.469,1.219 true 2.333,1.198 1.938,1.073 true 1.708,3.323 1.313,3.198 true 0.99,3.865 0.594,3.948 true 1.125,0.521 0.802,0.813 true 2.042,3.021 2.375,3.375 true 1.615,3.677 1.219,3.635 true 0.396,3.865 0.594,4.031 0.198,0.167 10 true *1 2.333,1.125 2.521,1.302 0.188,0.177 10 true *2 0.573,0.729 0.781,0.885 0.208,0.156 10 true *a 2.333,0.479 2.542,0.635 0.208,0.156 10 true *b 1.26,1.135 1.469,1.323 0.208,0.188 10 true *c 2.375,3.281 2.583,3.438 0.208,0.156 10 true *a 1.625,3.604 1.833,3.792 0.208,0.188 10 true *c 1.708,3.25 1.917,3.406 0.208,0.156 10 true *b 3.198,0.115 3.646,0.385 0.448,0.271 18 true i, ii
*1 No. 1 Engine Hanger *2 No. 2 Engine Hanger
*a Division Bar *b Shackle (A)
*c Chain - -


i.

Connect the division bar to the No. 1 engine hanger with the shackle (A) and chain.

NOTICE:

Connect the 1st link of the chain to the No. 1 engine hanger.



ii.

Connect the division bar to the No. 2 engine hanger with the shackle (A) and chain.

NOTICE:

Connect the 2nd link of the chain to the No. 2 engine hanger.




f.
C430499C02
3.135,0.635 3.448,0.792 0.313,0.156 10 false *a 0.448,0.052 0.729,0.406 0.281,0.354 18 false i
*a 120 mm (4.72 in.) or more - -


i.

Make sure the distance between the chain block assembly and suspension ring is 120 mm (4.72 in.) or more.

HINT:

If the suspension height is less than 120 mm, adjust the links of the chain which connect the division bar and engine hanger.




g.
C446021C02
3.948,0.708 4.208,0.406 false 3.458,1.135 3.76,1.229 false 3.792,1.156 3.979,1.302 0.188,0.146 10 true *a 4.24,0.313 4.552,0.469 0.313,0.156 10 false *b 5.729,0.229 6.042,0.385 0.313,0.156 10 false *c 3.219,0.156 3.531,0.313 0.313,0.156 10 false *e 1.396,1.688 1.708,1.844 0.313,0.156 10 false *f 5.729,1.688 6.042,1.844 0.313,0.156 10 false *f 0.427,0.115 0.656,0.573 0.229,0.458 18 true i 1.406,0.208 1.719,0.365 0.313,0.156 10 false *d
*a Chain Block *b Main Beam
*c Dimension (A) *d Dimension (B)
*e Right to Left Adjustment *f Front to Rear Adjustment


i.

Adjust the positions of the chain block assembly, support brackets and main beam so that the chain of the chain block assembly is perpendicular to the main beam and the length of the main beam on the outer side of the support bracket LH and RH is the same as shown in the illustration.

CAUTION:
·

To prevent the engine with continuously variable transaxle assembly from falling, make sure that the length of dimension (A) and dimension (B) are equal.

·
C446022C02
1.302,1.823 1.719,1.406 false 1.75,1.333 1.958,1.479 0.208,0.146 10 false *a
*a Main Beam


Do not perform any procedures if the length of dimension (A) and dimension (B) are not equal.

·

Performing any procedure when the length of dimension (A) and dimension (B) are not equal may cause the engine assembly with continuously variable transaxle assembly and engine support bridge to fall, possibly causing serious injury.



NOTICE:
C330751

·

Do not perform any procedures if the chain of the chain block assembly is not straight.

·

When removing the engine mount, if the chain of the chain block assembly is not straight, the engine assembly or transaxle assembly may contact the vehicle body.





h.
C446023C02
1.26,1.729 1.479,1.885 0.219,0.156 10 true *b 5.833,1.75 6.052,1.906 0.219,0.156 10 true *b 2.219,0.302 2.417,0.479 0.198,0.177 10 false *a 4.885,0.292 5.083,0.469 0.198,0.177 10 false *a 4.583,1.24 4.75,1.417 0.167,0.177 10 true *a 5.26,1.458 5.417,1.667 0.156,0.208 10 true *a 2.531,1.271 2.729,1.448 0.198,0.177 10 true *a 1.823,1.458 1.979,1.635 0.156,0.177 10 true *a 0.427,0.115 0.656,0.375 0.229,0.26 18 false i
*a Wing Bolt *b Bolt


i.

Confirm the appropriate installation state of the engine support bridge and tighten the 6 wing bolts and 2 bolts.

Torque:
Bolt : 30 N*m (306 kgf*cm, 22 ft.*lbf)

CAUTION:
·
C330761

Do not perform any procedures before tightening the bolts to the specified torque.

·

Performing procedures without tightening the bolts to the specified torque, may cause the engine support bridge to fall.





i.
C446024C02
5.698,1.177 5.885,1.333 0.188,0.156 10 true *a 0.427,0.115 0.583,0.542 0.156,0.427 18 false i
*a Turn - -


i.

Tighten the chain block assembly until it cannot be moved any further by hand.

CAUTION:
C330770C01
2.99,2.292 3.302,2.448 0.313,0.156 10 false *a
*a 41 N*m (418 kgf*cm, 30 ft.*lbf) or more


·

When suspending the engine with continuously variable transaxle assembly, do not tighten the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf).

·

Tightening the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf) will cause the load capacity (400 kg (881.8 lb)) to be exceeded and may cause damage to the engine support bridge and vehicle body.





Hide 12364B 36.SEPARATE NO. 2 ENGINE MOVING CONTROL ROD

a.
C446867


Hide 51201 37.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 12364B 38.REMOVE NO. 2 ENGINE MOVING CONTROL ROD

a.
C446025


Hide 30400 39.SUPPORT CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

Z101186

NOTICE:
·

Adjust the attachment of the transmission jack to securely fix the continuously variable transaxle assembly to the transmission jack.

·

Using a lashing belt or a rope, fix the continuously variable transaxle assembly to the transmission jack.




a.
C431054N01
0.438,0.083 0.719,0.438 0.281,0.354 18 false i

i.

Using a transmission jack, support the continuously variable transaxle assembly.



Hide 17118 40.REMOVE MANIFOLD STAY

Z101186

Click here(Click here)

Hide 11361J 41.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
C431058C03
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 32101G 42.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
C431059N01
0.5,0.083 0.667,0.333 0.167,0.25 18 false i

i.

Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

HINT:

There will be one black colored drive plate and torque converter assembly setting bolt.




Hide 12372A 43.REMOVE ENGINE MOUNTING INSULATOR LH

a.
C431060N01
3.917,0.115 4.104,0.417 0.188,0.302 18 true ii 0.563,0.115 0.75,0.417 0.188,0.302 18 true i 2.031,2.063 2.219,2.365 0.188,0.302 18 true iii

i.

Disengage the clamp to disconnect the engine wire from the engine mounting insulator LH.


ii.

Remove the nut and 3 bolts from the continuously variable transaxle assembly.


iii.

Remove the 4 bolts, nut and engine mounting insulator LH from the vehicle body.



Hide 30400 44.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

Z101186

NOTICE:

To prevent damage to the 2 knock pins, do not pry between the continuously variable transaxle assembly and engine assembly.


HINT:
·

Bolt (A), (B): Remove from continuously variable transaxle assembly side.

·

Bolt (C): Remove from engine assembly side.




a.
C431061N01
3.917,0.042 4.073,0.24 0.156,0.198 10 false A 2.875,0.208 3.031,0.406 0.156,0.198 10 false C 2.646,0.708 2.802,0.906 0.156,0.198 10 true C 2.813,1.344 2.969,1.542 0.156,0.198 10 true C 3.083,1.583 3.26,1.75 0.177,0.167 10 false C 4.01,1.573 4.156,1.729 0.146,0.156 10 false B 4.24,1.333 4.396,1.531 0.156,0.198 10 false C 0.479,0.094 0.76,0.448 0.281,0.354 18 false i

i.

Remove the 7 bolts and continuously variable transaxle assembly from the engine assembly.



Hide 32000A 45.REMOVE TORQUE CONVERTER ASSEMBLY

Z101186

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.



a.
C432049


Hide 30400E 46.REMOVE CVT OIL PUMP TYPE T OIL SEAL

Z101186

NOTICE:
·

Do not remove the stator shaft assembly from the CVT main body, as there is a possibility of the entry of dust and foreign matter.

·

Clean the work area, the tools to be used, and other equipment, etc. thoroughly before the operation, as there is the possibility that a CVT malfunction, which could prevent the vehicle from being able to be driven, could occur if dust or fine foreign matter enters the CVT.

·

Do not use cotton work gloves, cloths, or paper towels, etc. that may produce lint, dust or foreign matter.

·

Perform the operation as quickly as possible, as dust and foreign matter could enter the CVT while the torque converter assembly is removed.

·

Do not use an air gun until the torque converter assembly has been installed, as it could cause dust and foreign matter to be stirred up.




a.
C431063C04
2.417,2.167 2,1.917 true 1.333,2.667 2.167,2.667 2.167,2.667 2.167,2.583 false 1.75,2.667 1.75,2.583 false 5.438,2.208 5.438,1.875 false 5,0.833 4.573,1.26 false 2.604,1.792 2.323,1.708 false 5.323,2.271 5.781,2.469 0.458,0.198 10 false SST 1.167,2.594 1.479,2.75 0.313,0.156 10 false *a 2.438,2.167 2.75,2.323 0.313,0.156 10 false *b 0.708,0.104 1.021,0.438 0.313,0.333 18 false i 3.521,0.083 3.833,0.417 0.313,0.333 18 false ii 5.063,0.76 5.375,0.917 0.313,0.156 10 false *1 2.656,1.719 3.115,1.917 0.458,0.198 10 false SST
*1 CVT Type T Oil Seal - -
*a Clean *b Center Bolt


i.

Clean the tips of both the claws of SST and the center bolt.

SST
09308-10010  


ii.

Using SST, remove the CVT type T oil seal.

NOTICE:

Pay attention to the angle of the claws when opening them, and ensure that they do not come into contact with the oil pump housing, as there is the possibility that metal particles could be produced if they do.




Hide 47.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C431064


Hide 35150B 48.REMOVE TRANSMISSION CASE PLUG ASSEMBLY

a.

for Type A:

C446843


b.

for Type B:

C446844


Hide 32000A 49.INSPECT TORQUE CONVERTER ASSEMBLY

Hide 32101B 50.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY