Home › Drivetrain › K320 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (When Using the Engine Support Bridge) › from 2021.07
RM3700E _52 Drivetrain _092906 K320 MULTIDRIVE / CVT _0438045 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge) A

K320 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C462664N02
1.135,0.833 1.469,0.833 false 1.656,2.031 1.656,2.365 false 4.208,3.531 4.542,3.531 false 5.458,4.958 5.792,4.958 false 1.76,4.49 2.094,4.49 false 6.417,0.208 6.75,0.208 false 6.406,0.604 6.74,0.604 false 6.417,1 6.75,1 false 5.656,3.604 5.99,3.604 false 5.938,0.063 6.448,0.427 0.51,0.365 18 false 1, 2 1.594,1.156 1.906,1.354 0.313,0.198 10 false x2 5.156,3.448 5.469,3.646 0.313,0.198 10 false x2 3.167,5.438 3.479,5.635 0.313,0.198 10 false x4 3.417,5.313 3.729,5.51 0.313,0.198 10 false x4 3.854,5.25 4.167,5.448 0.313,0.198 10 false x9 6.219,0.458 6.5,0.813 0.281,0.354 18 false 3 5.281,4.823 5.563,5.177 0.281,0.354 18 false 4 1.583,4.333 1.865,4.688 0.281,0.354 18 false 5 4.031,3.385 4.313,3.74 0.281,0.354 18 false 6 1.604,2.375 1.885,2.729 0.281,0.354 18 false 7 6.042,3.469 6.323,3.823 0.281,0.354 18 false 8 1.531,0.698 1.813,1.052 0.281,0.354 18 false 9 5.688,0.854 6.51,1.219 0.823,0.365 18 false 10, 11

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 ALIGN FRONT WHEELS FACING STRAIGHT AHEAD - (Click here) - -
3 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
4 FRONT WHEELS - - - -
5 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -
6 ENGINE UNDER COVER LH 51442C - - -
7 ENGINE UNDER COVER RH 51441C - - -
8 FRONT FENDER LINER LH 53876A - - -
9 FRONT FENDER LINER RH 53875A - - -
10 DRAIN ENGINE COOLANT - - (Click here) -
11 DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID - - (Click here) -

C462666N03
0.083,0.083 7.083,2.917 7,2.833 0.083,2.917 7.083,5.75 7,2.833 3.479,0.479 3.813,0.479 false 4.333,0.802 4.667,0.802 false 6.146,1.885 6.479,1.885 false 5.906,4.667 6.24,4.667 false 4.844,4.125 5.177,4.125 false 3.375,3.292 3.708,3.292 false 4.49,2.469 4.823,2.469 false 4.479,5.354 4.813,5.354 false 0.167,0.177 0.542,0.417 0.375,0.24 12 false *A 0.167,3.01 0.542,3.25 0.375,0.24 12 false *B 2.292,3.552 2.75,3.75 0.458,0.198 10 false x12 2.292,0.698 2.75,0.896 0.458,0.198 10 false x11 4.885,2.333 5.438,2.688 0.552,0.354 18 false 16 5.229,4 5.781,4.354 0.552,0.354 18 false 15 3.854,0.354 4.406,0.708 0.552,0.354 18 false 13 6.281,4.542 6.833,4.896 0.552,0.354 18 false 14 3.76,3.167 4.313,3.521 0.552,0.354 18 false 12 4.875,5.219 5.427,5.573 0.552,0.354 18 false 16 4.719,0.667 5.271,1.021 0.552,0.354 18 false 15 6.521,1.76 7.073,2.115 0.552,0.354 18 false 12

Procedure Part Name Code
Z101186

Z101188

Z101187

12 WINDSHIELD WIPER MOTOR AND LINK - - - -
13 WATER GUARD PLATE RH 55734A - - -
14 WATER GUARD PLATE LH 55735A - - -
15 FRONT NO. 1 VENTILATOR SEAL 55815E - - -
16 OUTER COWL TOP PANEL SUB-ASSEMBLY 55701J - - -

*A for LHD *B for RHD

C462300N01
5.167,0.5 6.833,1.5 1.667,1 5.167,1.5 6.833,2.5 1.667,1 2.76,1.979 3.208,1.979 false 1.417,1.625 1.75,1.625 false 1.469,2.438 1.802,2.438 false 1.542,3.24 1.875,3.24 false 3.531,2.375 3.865,2.375 false 3.802,1.052 4.135,1.052 false 5.719,1.052 6.052,1.052 false 5.74,2.083 6.073,2.083 false 5.896,3.208 6.229,3.208 false 6.448,0.229 6.781,0.229 false 2.896,1.24 3.229,1.24 false 3.542,1.865 4.094,2.219 0.552,0.354 18 false 25 3.229,2.229 3.781,2.583 0.552,0.354 18 false 24 3.49,0.906 4.042,1.26 0.552,0.354 18 false 23 1.927,3.094 2.479,3.448 0.552,0.354 18 false 22 1.854,2.292 2.406,2.646 0.552,0.354 18 false 21 1.802,1.479 2.354,1.833 0.552,0.354 18 false 20 6.146,0.104 6.698,0.458 0.552,0.354 18 false 17 5.594,3.073 6.146,3.427 0.552,0.354 18 false 19 5.417,0.906 5.969,1.26 0.552,0.354 18 false 18 4.594,1.792 4.906,1.99 0.313,0.198 10 false x3 2.74,1.135 2.896,1.333 0.156,0.198 10 false ● 5.438,1.938 5.99,2.292 0.552,0.354 18 false 18 5.25,0.583 5.625,0.823 0.375,0.24 12 false *A 5.25,1.583 5.625,1.823 0.375,0.24 12 false *B

Procedure Part Name Code
Z101186

Z101188

Z101187

17 SECURE STEERING WHEEL - (Click here) - -
18 COLUMN HOLE COVER SILENCER SHEET 45259A - - -
19 NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY 45260 (Click here) - -
20 AIR CLEANER CAP WITH AIR CLEANER HOSE - - - -
21 AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY 17801 - - -
22 AIR CLEANER CASE SUB-ASSEMBLY 17701 - - -
23 ECM 89661 - - -
24 BATTERY CLAMP SUB-ASSEMBLY 74404A - - -
25 TRANSMISSION CONTROL CABLE ASSEMBLY 33820B (Click here) - -

*A for LHD *B for RHD
● Non-reusable part - -

C428846N08
2.667,1.083 3.083,1.083 false 4.708,1.833 5.042,1.833 false 5.948,4.583 6.365,4.583 false 1.563,5.24 1.896,5.24 false 0.865,4.75 1.198,4.75 false 1.26,3.906 1.594,3.906 false 4.656,1.208 4.969,1.406 0.313,0.198 10 false x2 6.365,4.833 6.635,5.052 0.271,0.219 10 false x2 3.448,0.958 4,1.313 0.552,0.354 18 false 26 5.094,1.688 5.646,2.042 0.552,0.354 18 false 30 6.729,4.438 7.042,4.781 0.313,0.344 18 false 27 1.25,5.094 1.594,5.427 0.344,0.333 18 false 28 0.542,4.635 0.885,4.979 0.344,0.344 18 false 31 0.948,3.76 1.26,4.104 0.313,0.344 18 false 29

Procedure Part Name Code
Z101186

Z101188

Z101187

26 ENGINE WIRE 82121 (Click here) - -
27 TCM 89535B (Click here) - -
28 NO. 4 WATER BY-PASS HOSE 16281N - - -
29 NO. 3 WATER BY-PASS HOSE ASSEMBLY 16290F - - -
30 NO. 1 TRANSMISSION CONTROL CABLE BRACKET 33823 - - -
31 STARTER ASSEMBLY 28100 - - -

C462302N02
3.417,3.583 6.5,5.583 3.083,2 0.333,3.583 3.417,5.583 3.083,2 1.021,2 1.354,2 false 3.99,2.385 3.99,2.719 false 5.26,4.146 5.594,4.146 false 1.354,4.198 1.521,4.198 1.521,4.198 1.771,4.448 false 5.688,0.646 6.021,0.646 false 5.208,5.021 5.042,5.021 5.042,5.021 4.792,4.771 false 4.01,2.792 4.563,3.146 0.552,0.354 18 false 34 5.625,3.979 6.177,4.333 0.552,0.354 18 false 33 5.271,4.875 5.823,5.229 0.552,0.354 18 false 32 1.573,2.865 1.885,3.063 0.313,0.198 10 false x2 1.406,1.906 1.563,2.104 0.156,0.198 10 false ● 5.521,0.552 5.677,0.75 0.156,0.198 10 false ● 1.969,3.26 2.281,3.458 0.313,0.198 10 false x2 5.781,2.042 6.094,2.24 0.313,0.198 10 false x2 5.99,1.479 6.302,1.677 0.313,0.198 10 false x2 1.042,4.052 1.594,4.406 0.552,0.354 18 false 32 1.958,5.25 2.271,5.448 0.313,0.198 10 false x2 2.792,4.813 3.104,5.01 0.313,0.198 10 false x2 4.271,5.25 4.583,5.448 0.313,0.198 10 false x4 5.281,4.396 5.594,4.594 0.313,0.198 10 false x2 0.417,3.667 0.792,3.906 0.375,0.24 12 false *A 3.5,3.667 3.875,3.906 0.375,0.24 12 false *B

Procedure Part Name Code
Z101186

Z101188

Z101187

32 CENTER NO. 4 ENGINE UNDER COVER 51447D - - -
33 CENTER NO. 1 FLOOR BRACE 57543C - - -
34 FRONT EXHAUST PIPE ASSEMBLY 17410 (Click here) - -

*A for TMC Made *B for TMMF Made
● Non-reusable part - -

C462295N01
5.771,1.552 6.521,1.719 0.75,0.167 0.448,2.5 1.198,2.667 0.75,0.167 2.885,4.635 3.219,4.635 false 0.833,2.167 0.833,2.5 false 4.552,1.635 4.552,1.885 false 5.438,1.635 5.771,1.635 false 5.76,4.458 6.177,4.458 false 4.844,2.865 4.844,3.198 false 1.521,1.781 1.188,1.781 false 1.063,0.823 1.063,1.156 false 6.75,0.24 6.417,0.24 false 3.5,5 3.813,5.198 0.313,0.198 10 false x3 4.24,5.146 4.552,5.344 0.313,0.198 10 false x2 5.344,5.24 5.656,5.438 0.313,0.198 10 false x2 5.802,5 6.115,5.198 0.313,0.198 10 false x2 5.479,1.646 5.792,1.844 0.313,0.198 10 false x2 0.906,2.177 1.219,2.375 0.313,0.198 10 false x2 0.521,2.51 1.844,2.906 1.323,0.396 8 false 43 (438, 32) 2.156,4.49 2.979,4.833 0.823,0.344 18 false 38, 40 6.469,4.333 6.792,4.667 0.323,0.333 18 false 39 0.833,1.656 1.156,1.99 0.323,0.333 18 false 36 4.573,1.875 4.896,2.208 0.323,0.333 18 false 36 5.698,0.104 6.635,0.427 0.938,0.323 18 false 37, 41 5.021,5.073 5.333,5.271 0.313,0.198 10 false x2 4.063,5.323 4.375,5.521 0.313,0.198 10 false x2 4.719,3.208 5.042,3.542 0.323,0.333 18 false 35 5.833,1.563 6.563,1.792 0.729,0.229 8 false 43 (438, 32) 0.938,1.177 1.26,1.51 0.323,0.333 18 false 35

Procedure Part Name Code
Z101186

Z101188

Z101187

35 FRONT DRIVE SHAFT ASSEMBLIES - - - -
36 ENGINE HANGERS - (Click here) - -
37 ENGINE SUPPORT BRIDGE - (Click here) - -
38 DISCONNECT NO. 2 ENGINE MOVING CONTROL ROD 12364B - - -
39 FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY 51201 (Click here) - -
40 REMOVE NO. 2 ENGINE MOVING CONTROL ROD 12364B - - -
41 SUPPORT CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY 30400 (Click here) - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

C446856N06
2.563,3.115 2.729,3.115 2.729,3.115 2.802,2.656 false 2.26,2.948 2.813,3.302 0.552,0.354 18 false 42

Procedure Part Name Code
Z101186

Z101188

Z101187

42 MANIFOLD STAY 17118 (Click here) - -

C462342N01
3.5,1.365 3.75,0.583 3.75,0.583 3.917,0.583 false 5.896,1.833 6.229,1.833 false 3.802,3.25 4.052,2.688 4.052,2.688 4.219,2.688 false 3.979,2.292 4.313,2.292 false 2.979,3.438 2.75,3.667 2.75,3.667 2.75,3.833 false 5.771,4.25 6.188,4.25 false 4.25,0.521 4.406,0.719 0.156,0.198 10 false ★ 4.438,0.448 4.99,0.802 0.552,0.354 18 false 44 6.271,1.688 6.823,2.042 0.552,0.354 18 false 45 4.385,2.135 4.938,2.49 0.552,0.354 18 false 43 4.75,2.583 5.302,2.938 0.552,0.354 18 false 48 4.594,2.646 4.802,2.823 0.208,0.177 10 false ● 2.823,3.885 3.375,4.24 0.552,0.354 18 false 47 6.531,4.115 7.01,4.469 0.479,0.354 18 false 46 1.104,3.542 1.417,3.74 0.313,0.198 10 false x5 3.615,1.323 3.927,1.521 0.313,0.198 10 false *a 5.073,1.073 5.385,1.271 0.313,0.198 10 false x3 5.844,0.958 6.156,1.156 0.313,0.198 10 false x4

Procedure Part Name Code
Z101186

Z101188

Z101187

43 FLYWHEEL HOUSING UNDER COVER 11361J - - -
44 DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT - (Click here) - -
45 ENGINE MOUNTING INSULATOR LH 12372A - - -
46 REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY 30400 (Click here) - -
47 REMOVE TORQUE CONVERTER ASSEMBLY 32000A (Click here) - -
48 CVT OIL PUMP TYPE T OIL SEAL 30400E (Click here) - -

*a Black Color: x1
Silver Color: x5
- -
● Non-reusable part ★ Precoated part

C463078N01
5.25,0.417 6.583,1.5 1.333,1.083 3.917,0.417 5.25,1.5 1.333,1.083 4.677,0.688 4.344,0.688 false 6.073,1.25 5.74,1.25 false 6.281,1.74 5.948,1.74 false 3.885,1.792 3.552,1.792 false 2.708,2.135 2.375,2.135 false 1.49,4.573 1.156,4.573 false 6.042,0.698 5.708,0.698 false 4.719,1.25 4.385,1.25 false 6.771,0.229 6.438,0.229 false 6.667,1.615 7.063,1.979 0.396,0.365 18 false 51 4.719,0.542 5.125,0.917 0.406,0.375 18 false 50 3.938,1.635 4.271,1.979 0.333,0.344 18 false 49 2.063,1.99 2.479,2.333 0.417,0.344 18 false 49 0.854,4.417 1.208,4.76 0.354,0.344 18 false 49 6.125,1.156 6.406,1.51 0.281,0.354 10 false ● 4,0.5 4.25,0.75 0.25,0.25 12 false *A 5.333,0.5 5.583,0.75 0.25,0.25 12 false *B 4.771,1.156 5.052,1.51 0.281,0.354 10 false ● 6.073,0.542 6.479,0.917 0.406,0.375 18 false 50 5.729,0.083 6.531,0.458 0.802,0.375 18 false 52, 53 6.552,1.656 6.833,2.01 0.281,0.354 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

49 WIRE HARNESS CLAMP BRACKET - - - -
50 TRANSMISSION CASE PLUG ASSEMBLY 35150B - - -
51 NO. 1 BREATHER PLUG 35141F (Click here) - -
52 INSPECT TORQUE CONVERTER ASSEMBLY 32000A (Click here) - -
53 INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY - (Click here) - -

*A for Type A *B for Type B
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the continuously variable transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
·

Air intake system parts

·

Exhaust system parts


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of continuously variable transaxle assembly
1.

Reset memory

2.

Transaxle compensation code (Input)

3.

CVT oil pressure calibration


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Front wheel alignment adjustment Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for TMC Made:
(Click here)
for TMMF Made:
(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (w/o Advanced Park) (Click here)

CAUTION:
·
C313282C01
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Heavy object exceeding the capacity of the transmission jack


Because the continuously variable transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the transmission jack could drop and components could fall down.


·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Z101186

Click here(Click here)

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 4.REMOVE FRONT WHEELS

Hide 51410 5.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51442C 6.REMOVE ENGINE UNDER COVER LH

Hide 51441C 7.REMOVE ENGINE UNDER COVER RH

a.

Perform the same procedure as for the LH side.


Hide 53876A 8.SEPARATE FRONT FENDER LINER LH

Hide 53875A 9.SEPARATE FRONT FENDER LINER RH

a.

Perform the same procedure as for the LH side.


Hide 10.DRAIN ENGINE COOLANT

Hide 11.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 12.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55734A 13.REMOVE WATER GUARD PLATE RH (for LHD)

Hide 55735A 14.REMOVE WATER GUARD PLATE LH (for RHD)

Hide 17.SECURE STEERING WHEEL

Z101186

Click here(Click here)

Hide 45259A 18.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 19.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Z101186

Click here(Click here)

Hide 20.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17801 21.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 22.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 24.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 33820B 25.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Z101186

Click here(Click here)

Hide 82121 26.DISCONNECT ENGINE WIRE

a.
C428822C10
0.49,0.135 1.021,0.698 0.531,0.563 18 false i, ii, iii, iv
V113147

Remove in this Direction - -


i.

Disengage the 2 claws, rotate the 2 lock levers and disconnect the 2 connectors.


ii.

Disconnect the 6 connectors.


iii.

Remove the bolt and separate the engine wire from the continuously variable transaxle assembly.


iv.

Disengage the 4 clamps to separate the engine wire.



b.
C462297N01
0.354,0.177 0.51,0.542 0.156,0.365 18 false i 3.417,0.188 3.938,0.49 0.521,0.302 18 false ii, iii 1.938,2.813 2.292,3.125 0.354,0.313 18 false iv

i.

Separate the No. 3 water by-pass hose assembly.


ii.

Remove the bolt and disconnect the engine wire from the continuously variable transaxle assembly.


iii.

Disengage the 3 clamps to separate the engine wire.


iv.

Disengage the 3 clamps to separate the engine wire.



Hide 89535B 27.REMOVE TCM

Z101186

NOTICE:

To prevent coolant from entering the TCM through its connector portion, be sure to remove the TCM before disconnecting any of the coolant system hoses.



a.
C431050


Hide 16281N 28.DISCONNECT NO. 4 WATER BY-PASS HOSE

Hide 16290F 29.DISCONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY

Hide 33823 30.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C431052


Hide 51447D 32.REMOVE CENTER NO. 4 ENGINE UNDER COVER

Hide 57543C 33.REMOVE CENTER NO. 1 FLOOR BRACE (for TMMF Made)

Hide 17410 34.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Z101186

Click here(Click here)

Hide 36.INSTALL ENGINE HANGERS

Z101186

Click here(Click here)

Hide 37.INSTALL ENGINE SUPPORT BRIDGE

a.
C462654C01
5.313,0.802 5.313,0.583 5.313,0.583 5.063,0.583 true 5.125,0.948 4.802,0.948 true 1.99,0.875 2.281,0.448 2.281,0.448 2.448,0.448 true 2.458,0.333 2.656,0.542 0.198,0.208 10 true *a 4.635,0.844 4.813,1.031 0.177,0.188 10 true *b 4.885,0.479 5.073,0.677 0.188,0.198 10 true *c 0.365,0 0.51,0.292 0.146,0.292 18 false i
*a Existing Hole *b Protective Tape
*c Bolt - -


i.

Cover the existing holes in the left and right suspension tower with protective tape, then use a thin-bladed screwdriver to make holes in the tape, and insert the 2 bolts for setting the sub-beam of the engine support bridge.

Item Part No.
Bolt 9010-10226



b.
C462655C01
2.406,1.313 2.219,1.313 2.219,1.313 2.094,1.052 true 4.76,1.406 4.948,1.406 4.948,1.406 5.115,1.115 true 1.781,5.208 2.115,5.208 true 2.115,5.938 2.115,6.198 true 5.094,4.906 5.542,4.906 true 4.667,5.635 4.99,5.635 true 2.125,5.094 2.323,5.292 0.198,0.198 10 true *a 2.031,6.188 2.24,6.375 0.208,0.188 10 true *b 2.417,1.198 2.615,1.396 0.198,0.198 10 true *c 4.552,1.292 4.75,1.49 0.198,0.198 10 true *c 4.896,4.792 5.094,4.99 0.198,0.198 10 true *a 4.458,5.531 4.667,5.719 0.208,0.188 10 true *b 0.375,0.01 0.552,0.26 0.177,0.25 18 true i
*a Support Shaft *b Front Side Member
*c Bolt - -


i.

Install SST to the vehicle body as shown in the illustration.

SST
09940-10010  

CAUTION:
·
C330755C01
0.448,1.167 0.781,1.167 false 2.438,1.167 2.771,1.167 false 1.052,1.781 1.052,1.448 1.052,1.448 1.219,1.448 false 2.604,1.781 2.604,1.448 2.604,1.448 2.438,1.448 false 0.292,1.094 0.604,1.25 0.313,0.156 10 false *a 2.271,1.094 2.583,1.25 0.313,0.156 10 false *a 1.281,1.385 1.594,1.542 0.313,0.156 10 false *b 2.271,1.385 2.583,1.542 0.313,0.156 10 false *b
*a Support Shaft
*b Front Side Member


Make sure that no oil or grease is on the front side member, and set the support shaft on the level surface of the front side member.

·

The engine support bridge may fall off if any oil or grease is still on or it is installed on the unlevel surface.



NOTICE:
·

Prevent SST from contacting the vehicle body exterior and windshield glass.

·

To prevent damage to the engine hood, place pieces of cloth between the engine hood and SST.

·

Lightly shake SST by hand to make sure it is securely installed before performing work.





c.
C462656C01
3.052,1.75 3.469,1.75 false 3.021,2 3.438,2 false 2.885,2.25 2.885,2.073 2.885,2.073 2.646,2.073 false 2.552,1.208 2.552,0.958 2.552,0.958 2.25,0.958 false 3.51,1.646 3.823,1.802 0.313,0.156 10 false *a 2.073,0.854 2.385,1.01 0.313,0.156 10 false *b 2.479,1.969 2.792,2.125 0.313,0.156 10 false *c 3.479,1.896 3.792,2.052 0.313,0.156 10 false *d 0.458,0.083 0.74,0.438 0.281,0.354 18 false i
*a Support Shaft *b Sub Beam
*c Front Side Member *d Threaded Portion


i.

Turn the threaded portion of each support shaft to adjust its height until the sub beams are parallel to the ground.



d.
C462657C01
0.365,0.688 1.375,0.688 false 1.083,1.865 1.375,1.865 true 1.688,1.094 2.01,1.094 false 1.479,2 1.906,2 true 2.063,0.99 2.375,1.146 0.313,0.156 10 false *a 0.198,0.604 0.51,0.76 0.313,0.156 10 false *b 0.885,1.75 1.052,1.938 0.167,0.188 10 true *c 1.927,1.875 2.104,2.073 0.177,0.198 10 true *d 0.344,0 0.969,0.313 0.625,0.313 18 false i, ii
*a Chain Block Assembly *b Sling Bracket
*c Fuse Shackle *d Shackle (A)


i.

Install the chain block assembly to the sling bracket.


ii.

Install the division bar to the chain block assembly with the shackles.

CAUTION:
·
C338949C01
0.458,2.313 0.583,2.313 0.583,2.313 0.875,2.635 false 0.354,2.677 0.479,2.677 0.479,2.677 0.865,2.865 false 2.177,2.271 2.302,2.271 2.302,2.271 2.604,2.594 false 2.073,2.656 2.198,2.656 2.198,2.656 2.583,2.844 false 0.281,2.208 0.604,2.469 0.323,0.26 10 false *a 0.167,2.573 0.51,2.844 0.344,0.271 10 false *b 1.99,2.156 2.313,2.417 0.323,0.26 10 false *a 1.885,2.542 2.229,2.813 0.344,0.271 10 false *b
*a Fuse Shackle
*b Shackle (A)


Make sure the fuse shackle is on the chain block assembly side and the shackle (A) is on the division bar side as shown in the illustration so that the fuse bolt is visible and can be checked for deformation easily.

·

If the fuse shackle is installed upside down, deformation of the fuse bolt will not be visible and cannot be used to tell if the load capacity of the engine support bridge has been exceeded. If the load capacity is exceeded, it may cause the engine support bridge to damage the vehicle and the engine assembly with continuously variable transaxle assembly may fall.

·
C330757C01
2.75,1 3.083,1 false 1.01,1 1.344,1 false 0.917,1.417 1.333,1.583 true 2.635,1.396 3.083,1.583 true 1.396,0.917 1.708,1.073 0.313,0.156 10 false *a 1.385,1.51 1.698,1.667 0.313,0.156 10 false *b 3.125,0.917 3.354,1.083 0.229,0.167 10 false *a 3.135,1.5 3.354,1.667 0.219,0.167 10 false *b
*a Fuse Shackle
*b Fuse Bolt


Make sure that the fuse bolt of the fuse shackle is free of damage, such as deformation or cracks. If damaged, replace the fuse shackle.

·

If a deformed fuse bolt is used, it cannot be used to tell if the load capacity of the engine support bridge has been exceeded. If the load capacity is exceeded, it may cause the engine support bridge to damage the vehicle and the engine assembly with transaxle assembly may fall.





e.
C462658C01
1.01,1.823 0.646,1.823 true 2.26,3.656 1.896,3.656 true 1.396,0.979 1.625,1.104 1.625,1.104 1.771,1.104 true 2.438,0.76 2.438,0.969 true 1.313,1.469 1.625,1.469 true 1.688,3.115 1.385,3.281 1.385,3.281 1.271,3.281 true 1.74,3.594 1.469,3.76 1.469,3.76 1.323,3.76 true 0.583,3.104 0.583,3.333 true 0.448,1.729 0.646,1.906 0.198,0.177 10 true *1 2.26,3.552 2.448,3.729 0.188,0.177 10 true *2 2.354,0.948 2.563,1.146 0.208,0.198 10 true *a 1.781,1 1.99,1.188 0.208,0.188 10 true *b 1.625,1.365 1.823,1.563 0.198,0.198 10 true *c 0.365,0 0.875,0.344 0.51,0.344 18 false i, ii 0.51,3.323 0.677,3.521 0.167,0.198 10 true *a 1.094,3.177 1.26,3.375 0.167,0.198 10 true *b 1.167,3.646 1.333,3.844 0.167,0.198 10 true *c
*1 No. 1 Engine Hanger *2 No. 2 Engine Hanger
*a Division Bar *b Shackle (A)
*c Chain - -


i.

Connect the division bar to the No. 1 engine hanger with the shackle (A) and chain.

NOTICE:

Connect the 1st link of the chain to the No. 1 engine hanger.



ii.

Connect the division bar to the No. 2 engine hanger with the shackle (A) and chain.

NOTICE:

Connect the 2nd link of the chain to the No. 2 engine hanger.




f.
C462659C01
3.146,0.615 3.458,0.771 0.313,0.156 10 false *a 0.375,0.01 0.656,0.365 0.281,0.354 18 false i
*a 120 mm (4.72 in.) or more - -


i.

Make sure the distance between the chain block assembly and suspension ring is 120 mm (4.72 in.) or more.

HINT:

If the suspension height is less than 120 mm, adjust the links of the chain which connect the division bar and engine hanger.




g.
C462660C01
4.021,0.927 4.24,0.51 4.24,0.51 4.438,0.51 false 3.313,1.458 3.719,1.458 true 3.74,1.375 3.938,1.583 0.198,0.208 10 true *a 4.49,0.406 4.802,0.563 0.313,0.156 10 false *b 5.844,0.385 6.156,0.542 0.313,0.156 10 false *c 1.083,0.375 1.396,0.531 0.313,0.156 10 false *d 1.073,2.313 1.24,2.5 0.167,0.188 10 true *f 3.031,0.302 3.344,0.469 0.313,0.167 10 false *e 0.365,0 0.646,0.354 0.281,0.354 18 false i 5.854,2.323 6.021,2.51 0.167,0.188 10 true *f
*a Chain Block Assembly *b Main Beam
*c Dimension (A) *d Dimension (B)
*e Right to Left Adjustment *f Front to Rear Adjustment


i.

Adjust the positions of the chain block assembly, support brackets and main beam so that the chain of the chain block assembly is perpendicular to the main beam and the length of the main beam on the outer side of the support bracket LH and RH is the same as shown in the illustration.

CAUTION:
·

To prevent the engine with continuously variable transaxle assembly from falling, make sure that the length of dimension (A) and dimension (B) are equal.

·
C330750C03
1.792,1.75 2.063,1.333 2.063,1.333 2.208,1.333 false 0.354,2.552 0.885,2.552 true 2.938,2.583 3.115,2.771 3.115,2.771 3.198,2.771 true 2.25,1.24 2.563,1.396 0.313,0.156 10 false *a 0.188,2.458 0.417,2.656 0.229,0.198 10 false *b 0.396,1.323 0.708,1.479 0.313,0.156 10 false *d 3.083,1.333 3.396,1.49 0.313,0.156 10 false *c 3.24,2.677 3.417,2.875 0.177,0.198 10 false *b
*a Main Beam
*b Sub Beam
*c Dimension (A)
*d Dimension (B)


Do not perform any procedures if the length of dimension (A) and dimension (B) are not equal.

·

Performing any procedure when the length of dimension (A) and dimension (B) are not equal may cause the engine assembly with continuously variable transaxle assembly and engine support bridge to fall, possibly causing serious injury.



NOTICE:
·
C330751

Do not perform any procedures if the chain of the chain block assembly is not straight.

·

When removing the engine mount, if the chain of the chain block assembly is not straight, the engine assembly or transaxle assembly may contact the vehicle body.





h.
C462661C01
1.229,1.708 1.417,1.896 0.188,0.188 10 true *b 5.833,1.656 6.021,1.844 0.188,0.188 10 true *b 2.271,0.073 2.469,0.271 0.198,0.198 10 false *a 4.375,1.167 4.573,1.354 0.198,0.188 10 true *a 5.125,1.344 5.313,1.542 0.188,0.198 10 true *a 2.615,1.188 2.813,1.365 0.198,0.177 10 true *a 1.875,1.344 2.073,1.542 0.198,0.198 10 true *a 0.354,0.01 0.635,0.365 0.281,0.354 18 false i 4.729,0.073 4.927,0.271 0.198,0.198 10 false *a
*a Wing Bolt *b Bolt


i.

Confirm the appropriate installation state of the engine support bridge and tighten the 6 wing bolts and 2 bolts.

Torque:
Bolt : 30 N*m (306 kgf*cm, 22 ft.*lbf)

CAUTION:
·
C330761

Do not perform any procedures before tightening the bolts to the specified torque.

·

Performing procedures without tightening the bolts to the specified torque, may cause the engine support bridge to fall.





i.
C462662C01
4.25,2.177 4.458,2.375 0.208,0.198 10 true *a 0.365,0 0.646,0.354 0.281,0.354 18 false i
*a Turn - -


i.

Tighten the chain block assembly until it cannot be moved any further by hand.

CAUTION:
C330770C01
2.99,2.292 3.302,2.448 0.313,0.156 10 false *a
*a 41 N*m (418 kgf*cm, 30 ft.*lbf) or more


·

When suspending the engine with continuously variable transaxle assembly, do not tighten the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf).

·

Tightening the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf) will cause the load capacity (400 kg (881.8 lb)) to be exceeded and may cause damage to the engine support bridge and vehicle body.





Hide 12364B 38.DISCONNECT NO. 2 ENGINE MOVING CONTROL ROD

a.
C446867


Hide 51201 39.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 12364B 40.REMOVE NO. 2 ENGINE MOVING CONTROL ROD

a.
C446025


Hide 30400 41.SUPPORT CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.
C431054N01
0.438,0.083 0.719,0.438 0.281,0.354 18 false i

i.

Using a transmission jack and lashing belt or rope, support the continuously variable transaxle assembly.

NOTICE:
·

Adjust the attachment of the transmission jack to securely support the continuously variable transaxle assembly.

·

Using a lashing belt or a rope, secure the continuously variable transaxle assembly to the transmission jack.





Hide 17118 42.REMOVE MANIFOLD STAY

Z101186

Click here(Click here)

Hide 11361J 43.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
C431058C01
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 44.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
C431059N01
0.5,0.083 0.667,0.333 0.167,0.25 18 false i

i.

Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

HINT:

There will be one black colored drive plate and torque converter assembly setting bolt.




Hide 12372A 45.REMOVE ENGINE MOUNTING INSULATOR LH

a.
C462340N01
3.75,0.115 3.938,0.417 0.188,0.302 18 false ii 0.333,0.115 0.521,0.417 0.188,0.302 18 false i 1.896,2.063 2.083,2.365 0.188,0.302 18 false iii

i.

Disengage the clamp to separate the engine wire from the engine mounting insulator LH.


ii.

Remove the 3 bolts and nut and separate the engine mounting insulator LH from the continuously variable transaxle assembly.


iii.

Remove the 4 bolts, nut and engine mounting insulator LH from the vehicle body.



Hide 30400 46.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

Z101186

NOTICE:

To prevent damage to the 2 knock pins, do not pry between the continuously variable transaxle assembly and engine assembly.



a.
C431061N01
3.917,0.042 4.073,0.24 0.156,0.198 10 false A 2.875,0.208 3.031,0.406 0.156,0.198 10 false C 2.646,0.708 2.802,0.906 0.156,0.198 10 true C 2.813,1.344 2.969,1.542 0.156,0.198 10 true C 3.083,1.583 3.26,1.75 0.177,0.167 10 false C 4.01,1.573 4.156,1.729 0.146,0.156 10 false B 4.24,1.333 4.396,1.531 0.156,0.198 10 false C 0.479,0.094 0.76,0.448 0.281,0.354 18 false i

i.

Remove the 7 bolts and continuously variable transaxle assembly from the engine assembly.

HINT:
·

Bolt (A), (B): Remove from the continuously variable transaxle assembly side.

·

Bolt (C): Remove from the engine assembly side.





Hide 32000A 47.REMOVE TORQUE CONVERTER ASSEMBLY

a.
C462336N01
0.385,0.052 0.667,0.406 0.281,0.354 18 false i

i.

Remove the torque converter assembly from the continuously variable transaxle assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.




Hide 30400E 48.REMOVE CVT OIL PUMP TYPE T OIL SEAL

Z101186

NOTICE:
·

Do not remove the stator shaft assembly from the CVT main body, as there is a possibility of the entry of dust and foreign matter.

·

Clean the work area, the tools to be used, and other equipment, etc. thoroughly before the operation, as there is the possibility that a CVT malfunction, which could prevent the vehicle from being able to be driven, could occur if dust or fine foreign matter enters the CVT.

·

Do not use cotton work gloves, cloths, or paper towels, etc. that may produce lint, dust or foreign matter.

·

Perform the operation as quickly as possible, as dust and foreign matter could enter the CVT while the torque converter assembly is removed.

·

Do not use an air gun until the torque converter assembly has been installed, as it could cause dust and foreign matter to be stirred up.




a.
C431063C01
2.417,2.167 2,1.917 true 1.333,2.667 2.167,2.667 2.167,2.667 2.167,2.583 false 1.75,2.667 1.75,2.583 false 5.438,2.208 5.438,1.875 false 5,0.833 4.573,1.26 false 2.604,1.792 2.323,1.708 false 5.323,2.271 5.781,2.469 0.458,0.198 10 false SST 1.167,2.594 1.479,2.75 0.313,0.156 10 false *a 2.438,2.167 2.75,2.323 0.313,0.156 10 false *b 0.708,0.104 1.021,0.438 0.313,0.333 18 false i 3.521,0.083 3.833,0.417 0.313,0.333 18 false ii 5.063,0.76 5.375,0.917 0.313,0.156 10 false *1 2.656,1.719 3.115,1.917 0.458,0.198 10 false SST
*1 CVT Oil Pump Type T Oil Seal - -
*a Clean *b Center Bolt


i.

Clean the tips of both the claws of SST and the center bolt.

SST
09308-10010  


ii.

Using SST, remove the CVT oil pump type T oil seal.

NOTICE:

Pay attention to the angle of the claws when opening them, and ensure that they do not come into contact with the oil pump housing, as there is the possibility that metal particles could be produced if they do.




Hide 49.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C431064


Hide 35150B 50.REMOVE TRANSMISSION CASE PLUG ASSEMBLY

a.
C462337C01
0.583,0.083 0.958,0.323 0.375,0.24 12 false *A 4.167,0.083 4.542,0.323 0.375,0.24 12 false *B
*A for Type A *B for Type B



Hide 35141F 51.REMOVE NO. 1 BREATHER PLUG

Z101186

HINT:

Perform this procedure only when replacement of the No. 1 breather plug.



a.
C462677


Hide 32000A 52.INSPECT TORQUE CONVERTER ASSEMBLY

Hide 53.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY