| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | CYLINDER HEAD GASKET | 11115 | ( )
|
- | - |
| 2 | CYLINDER HEAD SUB-ASSEMBLY | 11101 | ( )
|
- | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
| *T1 | 1st: 50 (510, 37)
2nd: Turn 90° 3rd: Turn 90° |
- | - |
| *A | Type A | *B | Type B |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | ★ | Precoated part |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | ★ | Precoated part |
| *a | x1 or x2 | *b | x4 or x3 |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| *A | w/ Differential Pressure Sensor | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
11115
1.INSTALL CYLINDER HEAD GASKET
| *a | Lot No. | - | - |
|
Front of Engine | - | - |
Place a new cylinder head gasket on the cylinder block sub-assembly with the Lot No. stamp facing upward.
Clean the cylinder block sub-assembly and cylinder head sub-assembly with solvent.
Make sure that the cylinder head gasket is installed in the correct orientation.
5.INSTALL CAMSHAFT BEARING CAP
13561
12.INSTALL NO. 1 CHAIN VIBRATION DAMPER
13559
13.INSTALL CHAIN TENSIONER SLIPPER
13521
15.INSTALL CRANKSHAFT TIMING GEAR OR SPROCKET
13506
16.INSTALL CHAIN SUB-ASSEMBLY
13519
19.INSTALL OIL PUMP DRIVE GEAR
16281
30.INSTALL NO. 4 WATER BY-PASS HOSE
36.INSTALL WATER BY-PASS HOSE ASSEMBLY
23470
37.INSTALL FUEL PUMP LIFTER ASSEMBLY
23802B
38.INSTALL NO. 2 FUEL PIPE SUB-ASSEMBLY
17177
41.INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET
25624
43.INSTALL EGR VALVE ADAPTER
25680
45.INSTALL EGR COOLER ASSEMBLY
12262
46.INSTALL NO. 2 VENTILATION HOSE
23820
47.INSTALL FUEL VAPOR FEED HOSE ASSEMBLY
25733A
52.INSTALL NO. 1 VACUUM PIPE (w/ Differential Pressure Sensor)
25760
53.INSTALL VACUUM TRANSMITTING HOSE ASSEMBLY (w/ Differential Pressure Sensor)
54.INSTALL ENGINE HANGERS