Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM(for Manual Transaxle) › 2016.04–2016.07
RM30M0E _51 Engine / Hybrid System _017072 2NZ-FE ENGINE CONTROL _0090868 SFI SYSTEM(for Manual Transaxle) C

2NZ-FE ENGINE CONTROL  SFI SYSTEM(for Manual Transaxle)  P1605  Rough Idling  


DESCRIPTION

This DTC is stored if the engine speed drops below the set speed without the ignition switch being operated.

Using the GTS, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

It is necessary to check if the vehicle ran out of fuel before performing troubleshooting, as this DTC is also stored when idling is unstable due to running out of fuel.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1605 Rough Idling After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to 400 rpm or less without the ignition switch being operated (1 trip detection logic).
·

Air leak in intake system

·

Purge VSV

·

Brake booster assembly

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Thermostat

·

Power supply circuit (purge VSV, heated oxygen sensor (sensor 1), fuel injector assembly, No. 1 ignition coil)

·

Fuel pump

·

Fuel pump control system

·

Fuel line

·

PCV valve and hose

·

Camshaft timing oil control valve assembly

·

Knock sensor

·

Ignition system

·

Air conditioning system (w/ Air Conditioning System)

·

Power steering system

·

Electrical load signal system

·

Charging system

·

ECM

·

Immobiliser system

·

Wire harness or connector


Does not come on DTC stored

WIRING DIAGRAM

Refer to DTC P0010 for the camshaft timing oil control valve circuit.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>P0010

Refer to DTC P0031 for the heated oxygen sensor (sensor 1) circuit.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>P0031

Refer to DTC P0100 for the mass air flow meter circuit.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>P0100

Refer to DTC P0115 for the engine coolant temperature sensor circuit.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>P0115

Refer to DTC P0351 for the ignition coil assembly circuit.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>P0351

Refer to DTC P0443 for the purge VSV circuit.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>P0443

Refer to Fuel Injector Circuit.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>Fuel Injector Circuit

CAUTION / NOTICE / HINT

HINT:
·

In contrast to normal malfunction diagnosis for components, circuits and systems, DTCs P1605 is used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine stall.

As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.

·

If any other DTCs are output, perform troubleshooting for those DTCs first.

·

Use any information from the customer problem analysis about the condition of the vehicle at the time when the problem occurred (conditions when the engine was restarted, etc.) as a reference.

Symptom Suspected Area
Engine can be started with accelerator pedal depressed Insufficient air volume
Rough idling after engine started Air fuel ratio abnormal, abnormal combustion

·

Read freeze frame data using the GTS. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

·

When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>FREEZE FRAME DATA

·

When confirming freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.

·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in neutral) and compare these data with the freeze frame data.

·

Inspections take into account the fact that the malfunction may not have reoccurred and place emphasis on checking the vehicle conditions present at the time when the malfunction occurred.

·

When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.



Inspection flow:

Using freeze frame data, narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred.


A224367E11
0.5,0.552 0.667,0.729 0.167,0.177 10 false 1: 0.5,0.729 1.583,1.323 1.083,0.594 10 false Did the engine speed decrease slowly or rapidly? 2.823,0.552 2.99,0.729 0.167,0.177 10 false 2: 2.823,0.729 3.875,1.281 1.052,0.552 10 false Was the air fuel ratio abnormal or normal? 5.688,0.719 6.583,1.042 0.896,0.323 10 false Intake air leak 5.552,1.729 6.729,2.01 1.177,0.281 10 false Sensor malfunction 5.521,2.719 6.771,2.979 1.25,0.26 10 false Fuel supply problem 4.031,2.063 4.708,2.49 0.677,0.427 10 false Air volume insufficient 3.927,3.052 4.802,3.521 0.875,0.469 10 false Ignition timing incorrect 1.583,2.708 2.635,3.25 1.052,0.542 10 false Injection and ignition stoppage 1.656,3.719 2.531,4.188 0.875,0.469 10 false Load from external parts 1.906,0.885 2.594,1.281 0.688,0.396 10 false Decreased Slowly 0.26,1.844 0.948,2.198 0.688,0.354 10 false Decreased Rapidly 4.302,0.896 4.927,1.156 0.625,0.26 10 false Abnormal 2.771,1.844 3.24,2.104 0.469,0.26 10 false Normal

1:
·

If the engine speed decreased slowly, there may have been a decrease in torque due to an air fuel ratio that was incorrect (by approximately 20 to 30%), etc.

·

If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.


2:
·

If the air fuel ratio is abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.

·

If the air fuel ratio was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.


P1605 inspection flow: Narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred (freeze frame data).

Engine Speed Suspected Area Primary Parts to Inspect Procedure
Slowly decreases Ignition system abnormal Igniter abnormal
·

Power supply circuit

·

No. 1 ignition coil

·

Spark plug


10, 38, 56
Air fuel ratio abnormal Air suction
·

Intake system connections

·

Purge VSV system

·

Brake booster assembly


5 to 9
Sensor malfunction (value from sensor too lean)
·

Mass air flow meter

·

Engine coolant temperature sensor

·

Heated oxygen sensor system

·

Thermostat


11 to 23
Sensor malfunction (value from sensor too rich) 39 to 48
52 to 54
Fuel supply problem
·

Fuel pump control system

·

Purge VSV system

·

Fuel line

·

ECM


24 to 37
Intake air volume abnormal Problem with air passage
·

Intake system connections

·

Mass air flow meter

·

Brake booster assembly

·

PCV valve and hose

·

Purge VSV system


57 to 59
Excessive valve overlap Camshaft timing oil control valve assembly 60, 61
Ignition timing incorrect Does not operate as expected
·

Knock sensor

·

Engine coolant temperature sensor

·

Mass air flow meter


62 to 66
Rapidly decreases Ignition and injection stops (electrical system malfunction) Power temporarily cut Power supply circuit (fuel injector assembly, No. 1 ignition coil) 67, 68
External part malfunctioning Increase in load
·

Air conditioning system (w/ air conditioning system)

·

Electrical load signal system

·

Power steering system


69, 70

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs.


Result:
Result Proceed to
Only DTC P1605 is output A
DTCs other than P1605 are output B


HINT:

If any DTCs other than P1605 are output, troubleshoot those DTCs first.



A

2.READ FREEZE FRAME DATA

B

2.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>FREEZE FRAME DATA

OK:

Immobiliser Fuel Cut is OFF.



Result:
Result Proceed to
Abnormal A
Normal B



A

3.CHECK IMMOBILISER SYSTEM

B

4.READ FREEZE FRAME DATA
3.CHECK IMMOBILISER SYSTEM
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Idle the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Immobiliser Communication and Immobiliser Fuel Cut.

Powertrain > Engine and ECT > Data List
Tester Display
Immobiliser Communication
Immobiliser Fuel Cut
50003 234 199,505

f.

Check the Data List indication.

OK:
Data List Item GTS Display
Immobiliser Communication ON
Immobiliser Fuel Cut OFF



Result:
Result Proceed to
OK A
NG (w/ smart entry and start system) B
NG (w/o smart entry and start system) C



A

4.READ FREEZE FRAME DATA

B

C

4.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>FREEZE FRAME DATA


Result:
Problem Symptom Freeze Frame Data Item Suspected Area Proceed to
Closed Throttle Position SW Engine Speed Total of Short FT #1 and Long FT #1
When idling or decelerating, engine speed slowly decreases (and engine stalls) All 5 sets of freeze frame data are ON Decreases slowly*1 All 5 sets of freeze frame data are 15% or more*2
·

Air suction

·

Sensor malfunction (value from sensor too lean)

·

Fuel supply problem


A
At least 1 of the 5 sets of freeze frame data is -15% or less*3 Sensor malfunction (value from sensor too rich) B
All 5 sets of freeze frame data are from -15% to 15%
·

Intake air volume abnormal

·

Ignition timing incorrect


C
When idling or decelerating, engine speed rapidly decreases (and engine stalls) Decreases rapidly*1 -
·

Injection stoppage, ignition stoppage

·

Load from external parts


D


A215381E11
0.094,0.094 2.177,0.344 2.083,0.25 10 Rapid Decrease in Engine Speed 2.365,0.417 2.781,0.667 0.417,0.25 10 (rpm) 2.396,0.75 2.729,1 0.333,0.25 10 800 2.396,0.958 2.729,1.208 0.333,0.25 10 600 2.396,1.156 2.729,1.323 0.333,0.167 10 400 2.396,1.365 2.729,1.531 0.333,0.167 10 200 2.542,1.563 2.854,1.729 0.313,0.167 10 0 3.031,1.656 3.281,1.906 0.25,0.25 10 #1 3.469,1.656 3.719,1.906 0.25,0.25 10 #2 3.917,1.656 4.156,1.906 0.24,0.25 10 #3 4.146,1.656 4.396,1.906 0.25,0.25 10 #4 4.385,1.656 4.719,1.99 0.333,0.333 10 #5 4.99,1.125 6.156,1.375 1.167,0.25 10 400 rpm or more 1.26,1.042 2.25,1.292 0.99,0.25 10 Engine Speed 2.667,1.958 5,2.292 2.333,0.333 10 Freeze Frame Data Storage Point

HINT:
·

*1: A rapid decrease in engine speed may have been caused by an electrical malfunction in the shared wiring of all or multiple cylinders, an increase in load from external parts, etc. The engine speed is considered to have decreased rapidly if either of the following conditions applies.

Otherwise, the engine speed is considered to have decreased slowly.

(a) In the freeze frame data, the decrease in engine speed from #3 to #5 is 400 rpm or higher.

(b) In the freeze frame data, the engine speed at #5 is 120 rpm or less.

·

*2: When a DTC is stored, feedback compensation increases because the air fuel ratio is determined to be lean.

·

*3: When a DTC is stored, feedback compensation decreases because the air fuel ratio is determined to be rich.




A

5.CHECK INTAKE SYSTEM

B

38.CHECK IGNITION SYSTEM

C

56.CHECK IGNITION SYSTEM

D

67.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
5.CHECK INTAKE SYSTEM
a.

Check for air leakage in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.].

Click hereEngine / Hybrid System>2NZ-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.

·

If Short FT #1 and Long FT #1 are largely different from the normal values when idling (the intake air volume is small) and almost the same as the normal values when racing the engine (the intake air volume is high), air leakage may be present.



OK:

There is no air suction.



Result:
Proceed to
OK
NG



OK

6.CHECK PURGE VSV

NG

REPAIR OR REPLACE INTAKE SYSTEM

6.CHECK PURGE VSV
a.
A299372C01
0.375,0.292 1.104,0.49 true 2.177,0.385 2.896,0.26 true 1.698,1.583 2.302,1.427 true 2.344,1.333 2.542,1.521 0.198,0.188 11 false *1 2.938,0.188 3.135,0.406 0.198,0.219 11 false *2 0.188,0.188 0.365,0.385 0.177,0.198 11 false *3
*1 Purge VSV
*2 Fuel Vapor Feed Hose (to Canister)
*3 Connector


Disconnect the fuel vapor feed hose (on the canister side) of the purge VSV.


b.

Start the engine.


c.

Idle the engine.


d.

Disconnect the B3 purge VSV connector.


e.

Check if air flows through the purge VSV.

OK:

Air does not flow.


HINT:

When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear the DTC.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>DTC CHECK / CLEAR



Result:
Proceed to
OK
NG



OK

7.READ FREEZE FRAME DATA

NG

7.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Stop Light Switch At least 1 of the 5 sets of freeze frame data is ON Air suction from brake booster assembly A
All 5 sets of freeze frame data are OFF - B



A

8.READ VALUE USING GTS (SHORT FT #1)

B

10.CHECK IGNITION SYSTEM
8.READ VALUE USING GTS (SHORT FT #1)
a.
A217928E14
0.333,0.583 1.083,0.833 0.75,0.25 10 Depressed 0.167,0.083 1,0.333 0.833,0.25 10 Brake Pedal 0.417,1.167 1.167,1.417 0.75,0.25 10 Released 0.167,1.917 1.083,2.167 0.917,0.25 10 Short FT #1 2.521,2.302 3.271,2.656 0.75,0.354 10 Change is 10% or less

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C (if equipped) and all accessory switches should be off.



e.

Idle the engine.


f.

Using the GTS, read the value of Short FT #1 in the Data List while depressing the brake pedal.

Powertrain > Engine and ECT > Data List
Tester Display
Short FT #1
50003 234 25
Standard:

Short FT #1 changes by 10% or less.


HINT:

When air leakage from the brake booster assembly is present, the feedback compensation increases because the air fuel ratio becomes lean.



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

9.PERFORM DRIVE TEST

B

C

9.PERFORM DRIVE TEST
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C (if equipped) and all accessory switches should be off.



c.

Idle the engine.


d.

Turn the GTS on.


e.

Using the GTS, read the value of Short FT #1 and Long FT #1 in the Data List.

Powertrain > Engine and ECT > Data List
Tester Display
Short FT #1
Long FT #1
50003 234 25,26
Standard:
Data List Condition Specified Condition
Short FT #1 + Long FT #1 The conditions of the vehicle are matched to those present when the problem occurs -15 to 15%



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

10.CHECK IGNITION SYSTEM

B

C

10.CHECK IGNITION SYSTEM
a.

Perform ignition system On-vehicle Inspection.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

11.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

11.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Calculate Load Below 90% of the current value of the vehicle*1 Mass air flow meter A
O2S B1S1 Below 0.45 V*2
·

Heated oxygen sensor (sensor 1)

·

Wire harness or connector


B


HINT:
·

*1: If the mass air flow meter is malfunctioning and incorrectly measures the intake air volume to be less than the actual volume, the freeze frame data will show a low engine load value.

·

*2: If the heated oxygen sensor (sensor 1) is malfunctioning and constantly outputs a value indicating the air fuel ratio is lean, the actual air fuel ratio will become rich and the engine may stall.




A

12.CHECK MASS AIR FLOW METER

B

15.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
12.CHECK MASS AIR FLOW METER

b.

Check for foreign matter in the air flow passage of the mass air flow meter.


Result:
Result Proceed to
Visible foreign matter is not present A
Visible foreign matter is present B



A

13.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

B

13.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Check the harnesses and connectors, referring to DTC P0100 inspection procedure.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>P0100

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

14.PERFORM DRIVE TEST

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.PERFORM DRIVE TEST
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C (if equipped) and all accessory switches should be off.



e.

Idle the engine.


f.

Using the GTS, read the value of Calculate Load in the Data List.

Powertrain > Engine and ECT > Data List
Tester Display
Calculate Load
50003 234 1
Standard:
Data List Specified Condition
Calculate Load 90 to 110% of the current value of the vehicle



Result:
Result Proceed to
Abnormal A
Normal B



A

B

18.READ FREEZE FRAME DATA
15.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.
A254132E08
0.552,0.375 1.635,0.542 1.083,0.167 10 false Injection Volume 1.104,0.823 1.646,0.99 0.542,0.167 10 false 12.5% 1.052,1.167 1.552,1.354 0.5,0.188 10 false -12.5% 0.219,1.854 2.667,2.042 2.448,0.188 10 false Heated Oxygen Sensor Output Voltage 0.396,2.365 1.604,2.51 1.208,0.146 10 false Higher than 0.5 V 0.698,2.771 1.479,2.917 0.781,0.146 10 false Below 0.4 V

Connect the GTS to the DLC3.


b.

Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.

HINT:

The A/C (if equipped) and all accessory switches should be off.



c.

Idle the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / O2S B1S1.

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
O2S B1S1
50004 234 2 42

f.

Read the output voltage from the heated oxygen sensor (sensor 1) when increasing and decreasing the fuel injection volume.

Standard:
GTS Display Specified Condition
Control the Injection Volume for A/F Sensor (12.5%) Heated oxygen sensor (sensor 1) output voltage is higher than 0.5 V
Control the Injection Volume for A/F Sensor (-12.5%) Heated oxygen sensor (sensor 1) output voltage is below 0.4 V



Result:
Result Proceed to
Abnormal A
Normal B


NOTICE:

The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.



A

16.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 1))

B

18.READ FREEZE FRAME DATA
16.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 1))
a.
A299376C01
0.813,1.021 1.167,1.26 0.354,0.24 1.854,0.969 2.188,0.667 true 0.229,0.177 0.5,0.417 0.271,0.24 10 false *a 0.875,1.063 1.177,1.271 0.302,0.208 10 false B24 2.24,0.563 2.531,0.771 0.292,0.208 10 false +B
*a Front view of wire harness connector
(to Heated Oxygen Sensor (Sensor 1))


Disconnect the heated oxygen sensor (sensor 1) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B24-2 (+B) - Body ground Ignition switch ON 11 to 14 V


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Result
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)

NG

REPAIR HEATED OXYGEN SENSOR POWER SOURCE CIRCUIT

17.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)
a.

Disconnect the B24 heated oxygen sensor (sensor 1) connector.


b.

Disconnect the B30 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B24-1 (HT1A) - B30-8 (HT1A) Always Below 1 Ω
B24-3 (OX1A) - B30-19 (OX1A) Always Below 1 Ω
B24-4 (E2) - B30-20 (EX1A) Always Below 1 Ω
B24-1 (HT1A) or B30-8 (HT1A) - Body ground Always 10 kΩ or higher
B24-3 (OX1A) or B30-19 (OX1A) - Body ground Always 10 kΩ or higher
B24-4 (E2) or B30-20 (EX1A) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

18.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Proceed to
Initial Engine Coolant Temp, Ambient Temp for A/C, Initial Intake Air Temp Difference in temperature between each item is less than 10°C (18°F)*1 A
Difference in temperature between each item is 10°C (18°F) or higher*2 B


HINT:
·

*1: A long time had elapsed after stopping the engine.

·

*2: A long time had not elapsed after stopping the engine.




A

19.READ FREEZE FRAME DATA

B

21.READ FREEZE FRAME DATA
19.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>FREEZE FRAME DATA

A217929E34
0.354,0.677 2.656,1.396 2.302,0.719 10 false Engine Coolant Temperature Increase after Engine Start (Engine Coolant Temperature - Engine Coolant Temperature at Engine Start) 3.292,0.063 3.583,0.26 0.292,0.198 10 false (°C) 5.604,2.115 6.219,2.281 0.615,0.167 10 false (Minutes) 5.156,1.688 5.313,1.844 0.156,0.156 10 false A 4.969,0.781 5.125,0.938 0.156,0.156 10 false C 3.896,0.49 4.052,0.646 0.156,0.156 10 false B 3.563,2.385 5.573,2.542 2.01,0.156 10 false Time Elapsed after Engine Start 2.979,0.385 3.24,0.583 0.26,0.198 10 false 284 2.969,0.615 3.229,0.813 0.26,0.198 10 false 248 2.969,0.844 3.229,1.042 0.26,0.198 10 false 212 2.958,1.083 3.219,1.281 0.26,0.198 10 false 176 2.958,1.313 3.26,1.51 0.302,0.198 10 false 140 2.948,1.542 3.229,1.74 0.281,0.198 10 false 104 3.031,2.01 3.24,2.219 0.208,0.208 10 false 32 3.021,1.781 3.208,1.969 0.188,0.188 10 false 68 2.979,0.063 3.271,0.26 0.292,0.198 10 false (°F)


Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Initial Engine Coolant Temp, Coolant Temp, Engine Run Time Range A
·

Engine coolant temperature sensor

·

Thermostat


A
Range B Engine coolant temperature sensor B
Range C - C


HINT:

This step is not directly related to engine stall.



A

20.INSPECT THERMOSTAT

B

22.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

C

24.READ FREEZE FRAME DATA
20.INSPECT THERMOSTAT

Result:
Result Proceed to
Abnormal A
Normal B



A

B

22.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
21.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Coolant Temp 120°C (248°F) or higher Engine coolant temperature sensor A
Coolant Temp, Ambient Temp for A/C Engine coolant temperature is lower than outside temperature by 15°C (27°F) or higher Engine coolant temperature sensor
Both freeze frame data items listed above Values are other than above - B



A

22.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

24.READ FREEZE FRAME DATA
22.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Proceed to
OK
NG



OK

23.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

NG

23.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the B18 engine coolant temperature sensor connector.


b.

Disconnect the B32 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B18-2 - B32-21 (THW) Always Below 1 Ω
B18-1 - B32-19 (E2) Always Below 1 Ω
B18-2 or B32-21 (THW) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

24.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Suspected Area Proceed to
EVAP (Purge) VSV At least 1 of the 5 sets of freeze frame data is not 0% Purge VSV A
All 5 sets of freeze frame data are 0% - B


HINT:

If the purge VSV is stuck closed, air fuel ratio compensation by the purge VSV is incorrectly adjusted, and then the air fuel ratio becomes lean and the engine may stall.



A

25.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL)

B

33.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
25.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A299373C03
2.073,0.5 2.823,0.375 true 2.281,1.438 1.677,1.604 true 2.313,1.344 2.51,1.542 0.198,0.198 10 false *1 2.865,0.292 3.177,0.49 0.313,0.198 10 false *2
*1 Purge VSV
*2 Fuel Vapor Feed Hose (to Canister)


Disconnect the fuel vapor feed hose (on the canister side) of the purge VSV.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

Powertrain > Engine and ECT > Active Test
Tester Display
Activate the VSV for Evap Control
50004 234 6

g.

When purge VSV is operated using the GTS, check whether the port of the purge VSV applies suction your finger.

OK:
GTS Operation Specified Condition
ON Purge VSV port applies suction to finger
OFF Purge VSV port applies no suction to finger



Result:
Result Proceed to
Abnormal A
Normal B


HINT:

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.



A

26.INSPECT PURGE VSV

B

33.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
26.INSPECT PURGE VSV

Result:
Proceed to
OK
NG



OK

27.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)

NG

27.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)
a.

Check the harness and connectors, referring to DTC P0443 inspection procedure.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>P0443

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

28.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

28.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Check the harness and connectors, referring to DTC P0443 inspection procedure.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>P0443

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

29.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

30.READ VALUE USING GTS (EVAP (PURGE) VSV)
30.READ VALUE USING GTS (EVAP (PURGE) VSV)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C (if equipped) and all accessory switches should be off.



c.

Idle the engine for 15 minutes or more.


d.

Turn the GTS on.


e.

Using the GTS, read the value of EVAP (Purge) VSV in the Data List.

Powertrain > Engine and ECT > Data List
Tester Display
EVAP (Purge) VSV
50003 234 31
Standard:
Data List Specified Condition
EVAP (Purge) VSV Value other than 0% is displayed



Result:
Result Proceed to
Abnormal A
Normal B



A

31.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL)

B

31.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A299373C03
2.073,0.5 2.823,0.375 true 2.281,1.438 1.677,1.604 true 2.313,1.344 2.51,1.542 0.198,0.198 10 false *1 2.865,0.292 3.177,0.49 0.313,0.198 10 false *2
*1 Purge VSV
*2 Fuel Vapor Feed Hose (to Canister)


Disconnect the fuel vapor feed hose (on the canister side) of the purge VSV.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

Powertrain > Engine and ECT > Active Test
Tester Display
Activate the VSV for Evap Control
50004 234 6

g.

When purge VSV is operated using the GTS, check whether the port of the purge VSV applies suction your finger.

OK:
GTS Operation Specified Condition
ON Purge VSV port applies suction to finger
OFF Purge VSV port applies no suction to finger



Result:
Result Proceed to
Abnormal A
Normal B


HINT:

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.



A

32.CHECK CONNECTOR CONNECTION CONDITION (ECM)

B

32.CHECK CONNECTOR CONNECTION CONDITION (ECM)
a.

Check the ECM connector connection condition.

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

NG

RECONNECT CONNECTOR CORRECTLY

33.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

e.

when performing the Active Test, check for an operating sound from the fuel pump.

OK:
GTS Operation Specified Condition
ON Operating sound heard
OFF Operating sound not heard



Result:
Result Proceed to
Abnormal A
Normal B


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.

·

If the fuel pump operating noise is abnormal, proceed to step 34.




A

34.INSPECT FUEL PUMP

B

35.CHECK FUEL SYSTEM
34.INSPECT FUEL PUMP
a.

Result:
Proceed to
OK
NG



OK

NG

35.CHECK FUEL SYSTEM
a.

Check the fuel system.

·

Check the fuel pump operation.

·

Check the fuel leaks.

·

Check the fuel pressure.

·

Perform the Active Test [Control the All Cylinders Fuel Cut].


HINT:

For the fuel system On-vehicle Inspection, refer to the following procedures.

Click hereEngine / Hybrid System>2NZ-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION



Result:
Result Proceed to
Abnormal A
Normal B



A

36.CHECK FUEL SYSTEM

B

36.CHECK FUEL SYSTEM
a.

Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.


Result:
Result Proceed to
There is foreign matter or signs that fuel pump was stuck A
There is no foreign matter and no signs that fuel pump was stuck B


HINT:

If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.



A

37.CHECK FUEL SYSTEM

B

REPAIR OR REPLACE FUEL SYSTEM

37.CHECK FUEL SYSTEM
a.

Check the fuel system.

·

Check the fuel pump operation.

·

Check the fuel leaks.

·

Check the fuel pressure.

·

Perform the Active Test [Control the All Cylinders Fuel Cut].


HINT:

For the fuel system On-vehicle Inspection, refer to the following procedures.

Click hereEngine / Hybrid System>2NZ-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION



Result:
Proceed to
OK
NG



OK

END

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

38.CHECK IGNITION SYSTEM
a.

Perform ignition system On-vehicle Inspection.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

39.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

39.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Calculate Load 110% or more of the current value of the vehicle*1 Mass air flow meter A
O2S B1S1 0.45 V or higher*2
·

Heated oxygen sensor (sensor 1)

·

Harness and connector


B
Both freeze frame data items listed above Values are other than above - C


HINT:
·

*1: If the mass air flow meter is malfunctioning and incorrectly measures the intake air volume to be higher than the actual volume of air flowing through the intake manifold, the freeze frame data will show a high engine load value.

·

*2: As the heated oxygen sensor (sensor 1) output is low before the sensor warms up, the value at that time cannot be used for diagnosis. If the heated oxygen sensor (sensor 1) is malfunctioning and constantly outputs a value indicating the air fuel ratio is rich, the actual air fuel ratio will become lean and the engine may stall.




A

40.INSPECT MASS AIR FLOW METER

B

43.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

C

46.READ FREEZE FRAME DATA
40.INSPECT MASS AIR FLOW METER

b.

Check for foreign matter in the air flow passage of the mass air flow meter.


Result:
Result Proceed to
Visible foreign matter is not present A
Visible foreign matter is present B



A

41.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

B

41.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Check the harnesses and connectors, referring to DTC P0100 inspection procedure.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>P0100

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

42.PERFORM DRIVE TEST

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

42.PERFORM DRIVE TEST
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C (if equipped) and all accessory switches should be off.



e.

Idle the engine.


f.

Using the GTS, read the value of Calculate Load in the Data List.

Powertrain > Engine and ECT > Data List
Tester Display
Calculate Load
50003 234 1
Standard:
Data List Specified Condition
Calculate Load 90 to 110% of the current value of the vehicle



Result:
Proceed to
OK
NG



OK

43.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

NG

43.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.
A254132E08
0.552,0.375 1.635,0.542 1.083,0.167 10 false Injection Volume 1.104,0.823 1.646,0.99 0.542,0.167 10 false 12.5% 1.052,1.167 1.552,1.354 0.5,0.188 10 false -12.5% 0.219,1.854 2.667,2.042 2.448,0.188 10 false Heated Oxygen Sensor Output Voltage 0.396,2.365 1.604,2.51 1.208,0.146 10 false Higher than 0.5 V 0.698,2.771 1.479,2.917 0.781,0.146 10 false Below 0.4 V

Connect the GTS to the DLC3.


b.

Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.

HINT:

The A/C (if equipped) and all accessory switches should be off.



c.

Idle the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / O2S B1S1.

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
O2S B1S1
50004 234 2 42

f.

Read the output voltage from the heated oxygen sensor (sensor 1) when increasing and decreasing the fuel injection volume.

Standard:
GTS Display Specified Condition
Control the Injection Volume for A/F Sensor (12.5%) Heated oxygen sensor (sensor 1) output voltage is higher than 0.5 V
Control the Injection Volume for A/F Sensor (-12.5%) Heated oxygen sensor (sensor 1) output voltage is below 0.4 V



Result:
Result Proceed to
Abnormal A
Normal B


NOTICE:

The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.



A

44.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 1))

B

46.READ FREEZE FRAME DATA
44.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 1))
a.
A299376C01
0.813,1.021 1.167,1.26 0.354,0.24 1.854,0.969 2.188,0.667 true 0.229,0.177 0.5,0.417 0.271,0.24 10 false *a 0.875,1.063 1.177,1.271 0.302,0.208 10 false B24 2.24,0.563 2.531,0.771 0.292,0.208 10 false +B
*a Front view of wire harness connector
(to Heated Oxygen Sensor (Sensor 1))


Disconnect the heated oxygen sensor (sensor 1) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B24-2 (+B) - Body ground Ignition switch ON 11 to 14 V


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Result
OK
NG



OK

45.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)

NG

REPAIR HEATED OXYGEN SENSOR POWER SOURCE CIRCUIT

45.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)
a.

Disconnect the B24 heated oxygen sensor (sensor 1) connector.


b.

Disconnect the B30 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B24-1 (HT1A) - B30-8 (HT1A) Always Below 1 Ω
B24-3 (OX1A) - B30-19 (OX1A) Always Below 1 Ω
B24-4 (E2) - B30-20 (EX1A) Always Below 1 Ω
B24-1 (HT1A) or B30-8 (HT1A) - Body ground Always 10 kΩ or higher
B24-3 (OX1A) or B30-19 (OX1A) - Body ground Always 10 kΩ or higher
B24-4 (E2) or B30-20 (EX1A) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

46.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

46.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Proceed to
Initial Engine Coolant Temp, Ambient Temp for A/C, Initial Intake Air Temp Difference in temperature between each item is less than 10°C (18°F)*1 A
Difference in temperature between each item is 10°C (18°F) or higher*2 B


HINT:
·

*1: A long time had elapsed after stopping the engine.

·

*2: A long time had not elapsed after stopping the engine.




A

47.READ FREEZE FRAME DATA

B

52.READ FREEZE FRAME DATA
47.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>FREEZE FRAME DATA

A217929E34
0.354,0.677 2.656,1.396 2.302,0.719 10 false Engine Coolant Temperature Increase after Engine Start (Engine Coolant Temperature - Engine Coolant Temperature at Engine Start) 3.292,0.063 3.583,0.26 0.292,0.198 10 false (°C) 5.604,2.115 6.219,2.281 0.615,0.167 10 false (Minutes) 5.156,1.688 5.313,1.844 0.156,0.156 10 false A 4.969,0.781 5.125,0.938 0.156,0.156 10 false C 3.896,0.49 4.052,0.646 0.156,0.156 10 false B 3.563,2.385 5.573,2.542 2.01,0.156 10 false Time Elapsed after Engine Start 2.979,0.385 3.24,0.583 0.26,0.198 10 false 284 2.969,0.615 3.229,0.813 0.26,0.198 10 false 248 2.969,0.844 3.229,1.042 0.26,0.198 10 false 212 2.958,1.083 3.219,1.281 0.26,0.198 10 false 176 2.958,1.313 3.26,1.51 0.302,0.198 10 false 140 2.948,1.542 3.229,1.74 0.281,0.198 10 false 104 3.031,2.01 3.24,2.219 0.208,0.208 10 false 32 3.021,1.781 3.208,1.969 0.188,0.188 10 false 68 2.979,0.063 3.271,0.26 0.292,0.198 10 false (°F)


Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Initial Engine Coolant Temp, Coolant Temp, Engine Run Time Range A
·

Engine coolant temperature sensor

·

Thermostat


A
Range B Engine coolant temperature B
Range C - C


HINT:

This step is not directly related to engine stall.



A

48.INSPECT THERMOSTAT

B

53.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

C

49.CHECK FUEL SYSTEM
48.INSPECT THERMOSTAT

Result:
Result Proceed to
Abnormal A
Normal B


HINT:

This step is not directly related to engine stall.



A

B

53.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
49.CHECK FUEL SYSTEM
a.

Check the fuel system.

·

Check the fuel pump operation.

·

Check the fuel leaks.

·

Check the fuel pressure.

·

Perform the Active Test [Control the All Cylinder Fuel Cut].


HINT:

For the fuel system On-vehicle Inspection, refer to the following procedures.

Click hereEngine / Hybrid System>2NZ-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION



Result:
Result Proceed to
Abnormal A
Normal B



A

50.CHECK FUEL SYSTEM

B

50.CHECK FUEL SYSTEM
a.

Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.


Result:
Result Proceed to
There is no foreign matter and no signs that fuel pump was stuck A
There is foreign matter or signs that fuel pump was stuck B


HINT:

If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.



A

51.CHECK FUEL SYSTEM

B

REPAIR OR REPLACE FUEL SYSTEM

51.CHECK FUEL SYSTEM
a.

Check the fuel system.

·

Check the fuel pump operation.

·

Check the fuel leaks.

·

Check the fuel pressure.

·

Perform the Active Test [Control the All Cylinder Fuel Cut].


HINT:

For the fuel system On-vehicle Inspection, refer to the following procedures.

Click hereEngine / Hybrid System>2NZ-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION



Result:
Proceed to
OK
NG



OK

END

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

52.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>FREEZE FRAME DATA


Result:
Freeze Frame Data Item for Result Suspected Area Proceed to
Coolant Temp 120°C (248°F) or higher Engine coolant temperature sensor A
Coolant Temp, Ambient Temp for A/C Engine coolant temperature is lower than outside temperature by 15°C (27°F) or higher Engine coolant temperature sensor
Both freeze frame data items listed above Values are other than above - B



A

53.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

55.CLEAR DTC
53.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Proceed to
OK
NG



OK

54.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

NG

54.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the B18 engine coolant temperature sensor connector.


b.

Disconnect the B32 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B18-2 - B32-21 (THW) Always Below 1 Ω
B18-1 - B32-19 (E2) Always Below 1 Ω
B18-2 or B32-21 (THW) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

55.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

END

56.CHECK IGNITION SYSTEM
a.

Perform ignition system On-vehicle Inspection.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

57.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

57.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Total of ISC Learning Value and ISC Feedback Value Below 80% of the current value of the vehicle Intake air volume insufficient A
80% or higher of the current value of the vehicle B



A

58.CHECK INTAKE SYSTEM

B

60.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR (BANK1))
58.CHECK INTAKE SYSTEM
a.

Check for air leakage in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.].

Click hereEngine / Hybrid System>2NZ-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.

·

If Short FT #1 and Long FT #1 are largely different from the normal values when idling (the intake air volume is small) and almost the same as the normal values when racing the engine (the intake air volume is high), air leakage may be present.



OK:

There is no air leakage.



Result:
Proceed to
OK
NG



OK

59.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE INTAKE SYSTEM

59.CHECK INTAKE SYSTEM
a.

Check the intake system.



Result:
Result Proceed to
Abnormal A
Normal B



A

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

B

62.READ FREEZE FRAME DATA
60.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR (BANK1))
a.

Perform the Active Test, referring to DTC P0011 inspection procedure.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>P0011

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.

·

If the camshaft timing oil control valve assembly is stuck at the advanced side, the valve overlap increases and combustion worsens due to the interval EGR which may cause rough idle or cause the engine to stall.




Result:
Proceed to
OK
NG



OK

61.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

61.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Check the harnesses and connectors, referring to DTC P0010 inspection procedure.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>P0010

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

62.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

62.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Suspected Area Proceed to
IGN Advance Knock Correct Learn Value
Differs from the current value of the vehicle by 10 deg or more Less than 3 deg(CA)
·

Engine coolant temperature sensor

·

Mass air flow meter

·

Knock sensor


A
3 deg(CA) or more -
Differs from the current value of the vehicle by less than 10 deg - - B



A

63.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

63.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Proceed to
OK
NG



OK

64.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

NG

64.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the B18 engine coolant temperature sensor connector.


b.

Disconnect the B32 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B18-2 - B32-21 (THW) Always Below 1 Ω
B18-1 - B32-19 (E2) Always Below 1 Ω
B18-2 or B32-21 (THW) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

65.INSPECT MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

65.INSPECT MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR)
a.

Inspect the mass air flow meter.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>MASS AIR FLOW METER>INSPECTION

HINT:

If the intake air temperature sent to the ECM is higher than the standard due to the mass air flow (intake air temperature sensor) malfunctioning, the ignition timing may become delayed.



Result:
Proceed to
OK
NG



OK

66.READ VALUE USING GTS (IGN ADVANCE AND KNOCK CORRECT LEARN VALUE)

NG

66.READ VALUE USING GTS (IGN ADVANCE AND KNOCK CORRECT LEARN VALUE)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C (if equipped) and all accessory switches should be off.



c.

Turn the GTS on.


d.

Idle the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance and Knock Correct Learn Value.

Powertrain > Engine and ECT > Data List
Tester Display
IGN Advance
Knock Correct Learn Value
50003 234 29,191

f.

Check the Data List indication.


Result:
Data List Proceed to
IGN Advance Knock Correct Learn Value
Differs from the current value of the vehicle by 10 deg or more Less than 3 deg(CA) A
3 deg(CA) or more
Differs from the current value of the vehicle by less than 10 deg - B


HINT:

If the results of the checks performed in steps 57 to 63 were all normal and the sum of ISC Feedback Value and ISC Learning Value in the Data List is 120% of the normal value or more, check for carbon deposits in the throttle body assembly. If there are carbon deposits, clean them off to finish the troubleshooting procedure.



A

B

END

67.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
a.

Check the harness and connectors, referring to Fuel Injector Circuit inspection procedure.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>Fuel Injector Circuit

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)




Result:
Proceed to
OK
NG



OK

68.CHECK IGNITION SYSTEM

NG

68.CHECK IGNITION SYSTEM
a.

Perform ignition system On-vehicle Inspection.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

69.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

69.READ FREEZE FRAME DATA
HINT:

If the vehicle is not equipped with an air conditioning system, proceed to next step (B).


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Suspected Area Proceed to
A/C Signal Air Conditioner FB Val Power Steering Signal
A/C Signal display changes from OFF to ON*1 Value displayed for Air Conditioner FB Val increases - A/C system A
Value displayed for Air Conditioner FB Val does not increase Does not change from OFF - B
Changes from OFF to ON Power steering system
A/C Signal display does not change from OFF - Changes from OFF to ON
Does not change from OFF -


HINT:
·

*1: Check not only the ON/OFF state of the air conditioner but also the change in air conditioner load.

·

Even if the results are normal, the power steering system or A/C system may have been malfunctioning. If there are no problems with other parts, inspect the power steering system or A/C system.




A

B

70.READ FREEZE FRAME DATA
70.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Proceed to
Electrical Load Signal 1 (2) or Electric Load Feedback Val Electric Load Feedback Val
Electrical Load Signal 1 (2) display changes from OFF to ON*1, or value displayed for Electric Load Feedback Val increases*1 Value displayed for Electric Load Feedback Val changes A
Value displayed for Electric Load Feedback Val does not change B
Electrical Load Signal 1 (2) display does not change from OFF, or value displayed for Electric Load Feedback Val does not increase -


HINT:
·

*1: If the Electrical Load Signal 1 (2) display changes from OFF to ON, or the "Electric Load Feedback Val" increases, it probably is a malfunction due to a change in electrical load. Check the generator and the continuity and connections between the generator and ECM.

·

Even if the results are normal, the electrical load signal system may have been malfunctioning. If there are no problems with other parts, inspect the electrical load system.




A

B