The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the continuously variable transaxle assembly removal/installation are shown below.
| *a | Heavy object exceeding the capacity of the transmission jack |
Because the continuously variable transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.
If work is not performed according to the procedures described in the repair manual, there is a danger that the transmission jack could drop and components could fall down.
When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.
Touching high-temperature areas such as the engine and exhaust pipe could result in burns.
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
3.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
4.REMOVE FRONT WHEELS
51451A
5.REMOVE CENTER ENGINE UNDER COVER
51442C
6.REMOVE ENGINE UNDER COVER LH
51441C
7.REMOVE ENGINE UNDER COVER RH
53876A
8.SEPARATE FRONT FENDER LINER LH
53875A
9.SEPARATE FRONT FENDER LINER RH
10.DRAIN ENGINE COOLANT
11.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID
12.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
55815E
13.REMOVE FRONT NO. 1 VENTILATOR SEAL (for LHD)
55815E
14.REMOVE FRONT NO. 1 VENTILATOR SEAL (for RHD)
55734A
15.REMOVE WATER GUARD PLATE RH (for LHD)
55735A
16.REMOVE WATER GUARD PLATE LH (for RHD)
55701J
17.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)
55701J
18.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
19.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE
17701
20.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
89661
21.REMOVE ECM
74404A
22.REMOVE BATTERY CLAMP SUB-ASSEMBLY
33820B
23.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
82121
24.DISCONNECT ENGINE WIRE
Disengage the claw, rotate the lever and disconnect the transmission wire connector.
| *1 | Transmission Wire Connector | *2 | Shift Stroke Sensor Connector |
| *3 | Park/Neutral Position Switch Connector | *4 | Transmission Revolution Sensor (NOUT) Connector |
| *5 | TCM Connector | *6 | Transmission Revolution Sensor (NSS) Connector |
| *7 | Oil Pressure Sensor Connector | *8 | Transmission Revolution Sensor (NT) Connector |
|
Remove in this Direction | - | - |
Disconnect the shift stroke sensor connector.
Disconnect the park/neutral position switch connector.
Disconnect the transmission revolution sensor (NOUT) connector.
Disengage the claw, rotate the lever and disconnect the TCM connector.
Disconnect the transmission revolution sensor (NSS) connector.
Disconnect the oil pressure sensor connector.
Disconnect the transmission revolution sensor (NT) connector.
Remove the bolt.
Disengage the 4 clamps.
w/ Stop and Start System:
Disengage the clamp and disconnect the oil pump assembly connector.
Disconnect the No. 3 water by-pass hose assembly.
Disengage the 3 clamps.
Remove the bolt to disconnect the engine wire from the continuously variable transaxle assembly.
Disengage the 3 clamps to disconnect the engine wire from the front suspension crossmember sub-assembly.
89535B
25.REMOVE TCM
To prevent coolant from entering the TCM through its connector portion, be sure to remove the TCM before disconnecting any of the coolant system hoses.
Remove the 2 bolts and TCM from the continuously variable transaxle assembly.
16281N
26.DISCONNECT NO. 4 WATER BY-PASS HOSE
16290F
27.DISCONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY
33823
28.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET
Remove the 2 bolts and No. 1 transmission control cable bracket from the continuously variable transaxle assembly.
28100
29.REMOVE STARTER ASSEMBLY (w/ Stop And Start System)
28100
30.REMOVE STARTER ASSEMBLY (w/o Stop And Start System)
31.SECURE STEERING WHEEL
45259A
32.REMOVE COLUMN HOLE COVER SILENCER SHEET (for LHD)
45259A
33.REMOVE COLUMN HOLE COVER SILENCER SHEET (for RHD)
45260
34.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
51447D
35.REMOVE CENTER NO. 4 ENGINE UNDER COVER (for TMMF Made)
51447D
36.REMOVE CENTER NO. 4 ENGINE UNDER COVER (for TMC Made)
57543C
37.REMOVE CENTER NO. 1 FLOOR BRACE (for TMMF Made)
17410
38.REMOVE FRONT EXHAUST PIPE ASSEMBLY
39.REMOVE FRONT DRIVE SHAFT ASSEMBLIES (for TMMF Made)
40.REMOVE FRONT DRIVE SHAFT ASSEMBLIES (for TMC Made)
41.INSTALL ENGINE HANGERS
42.INSTALL ENGINE SUPPORT BRIDGE
| *a | Existing Hole |
| *b | Protective Tape |
| *c | Bolt |
Cover the existing holes in the left and right suspension tower with protective tape, then use a thin-bladed screwdriver to make holes in the tape, and insert the 2 bolts for setting the sub-beam of the engine support bridge.
| Item | Part No. |
|---|---|
| Bolt | 9010-10226 |
Install SST to the vehicle body as shown in the illustration.
| *a | Support Shaft | *b | Front Side Member |
| *c | Front Suspension Nut | - | - |
| *a | Support Shaft |
| *b | Front Side Member |
Make sure that no oil or grease is on the front side member, and set the support shaft on the level surface of the front side member.
The engine support bridge may fall off if any oil or grease is still on or it is installed on the unlevel surface.
Prevent SST from contacting the vehicle body exterior and windshield glass.
To prevent damage to the engine hood, place pieces of cloth between the engine hood and SST.
Lightly shake SST by hand to make sure it is securely installed before performing work.
| *a | Support Shaft |
| *b | Sub Beam |
| *c | Front Side Member |
| *d | Threaded Portion |
Turn the threaded portion of each support shaft to adjust its height until the sub beams are parallel to the ground.
Install the chain block to the sling bracket.
| *a | Chain Block | *b | Sling Bracket |
| *c | Fuse Shackle | *d | Shackle (A) |
Install the division bar to the chain block with the shackles.
| *a | Fuse Shackle |
| *b | Shackle (A) |
Make sure the fuse shackle is on the chain block side and the shackle (A) is on the division bar side as shown in the illustration so that the fuse bolt is visible and can be checked for deformation easily.
If the fuse shackle is installed upside down, deformation of the fuse bolt will not be visible and cannot be used to tell if the load capacity of the engine support bridge has been exceeded. If the load capacity is exceeded, it may cause the engine support bridge to damage the vehicle and the engine assembly with continuously variable transaxle assembly may fall.
| *a | Fuse Shackle |
| *b | Fuse Bolt |
Make sure that the fuse bolt of the fuse shackle is free of damage, such as deformation or cracks. If damaged, replace the fuse shackle.
If a deformed fuse bolt is used, it cannot be used to tell if the load capacity of the engine support bridge has been exceeded. If the load capacity is exceeded, it may cause the engine support bridge to damage the vehicle and the engine assembly with transaxle assembly may fall.
Connect the division bar to the No. 1 engine hanger with the shackle (A) and chain.
| *1 | No. 1 Engine Hanger | *2 | No. 2 Engine Hanger |
| *a | Division Bar | *b | Shackle (A) |
| *c | Chain | - | - |
Connect the 1st link of the chain to the No. 1 engine hanger.
Connect the division bar to the No. 2 engine hanger with the shackle (A) and chain.
Connect the 2nd link of the chain to the No. 2 engine hanger.
| *a | 120 mm (4.72 in.) or more |
Make sure the distance between the chain block assembly and suspension ring is 120 mm (4.72 in.) or more.
If the suspension height is less than 120 mm, adjust the links of the chain which connect the division bar and engine hanger.
Adjust the positions of the chain block assembly, support brackets and main beam so that the chain of the chain block assembly is perpendicular to the main beam and the length of the main beam on the outer side of the support bracket LH and RH is the same as shown in the illustration.
| *a | Chain Block | *b | Main Beam |
| *c | Dimension (A) | *d | Dimension (B) |
| *e | Right to Left Adjustment | *f | Front to Rear Adjustment |
To prevent the engine with continuously variable transaxle assembly from falling, make sure that the length of dimension (A) and dimension (B) are equal.
| *a | Main Beam |
Do not perform any procedures if the length of dimension (A) and dimension (B) are not equal.
Performing any procedure when the length of dimension (A) and dimension (B) are not equal may cause the engine assembly with continuously variable transaxle assembly and engine support bridge to fall, possibly causing serious injury.
Do not perform any procedures if the chain of the chain block assembly is not straight.
When removing the engine mount, if the chain of the chain block assembly is not straight, the engine assembly or transaxle assembly may contact the vehicle body.
Confirm the appropriate installation state of the engine support bridge and tighten the 6 wing bolts and 2 bolts.
| *a | Wing Bolt | *b | Bolt |
Do not perform any procedures before tightening the bolts to the specified torque.
Performing procedures without tightening the bolts to the specified torque, may cause the engine support bridge to fall.
| *a | Turn |
Tighten the chain block assembly until it cannot be moved any further by hand.
| *a | 41 N*m (418 kgf*cm, 30 ft.*lbf) or more |
When suspending the engine with continuously variable transaxle assembly, do not tighten the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf).
Tightening the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf) will cause the load capacity (400 kg (881.8 lb)) to be exceeded and may cause damage to the engine support bridge and vehicle body.
51201
43.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
12364B
44.REMOVE NO. 2 ENGINE MOVING CONTROL ROD
Remove the 3 bolts and No. 2 engine moving control rod from the continuously variable transaxle assembly.
30400
45.SUPPORT CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
| *a | Lashing Belt |
Using a transmission jack, support the continuously variable transaxle assembly.
Adjust the attachment of the transmission jack to securely fix the continuously variable transaxle assembly to the transmission jack.
Using a lashing belt or a rope, fix the continuously variable transaxle assembly to the transmission jack.
17118
46.REMOVE MANIFOLD STAY
11361J
47.REMOVE FLYWHEEL HOUSING UNDER COVER
|
Remove in this Direction |
Remove the flywheel housing under cover from the cylinder block sub-assembly.
32101G
48.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.
There will be one black colored drive plate and torque converter assembly setting bolt.
12372A
49.REMOVE ENGINE MOUNTING INSULATOR LH
Disengage the clamp to disconnect the engine wire from the engine mounting insulator LH.
Remove the nut and 3 bolts from the continuously variable transaxle assembly.
Remove the 4 bolts, nut and engine mounting insulator LH from the vehicle body.
30400
50.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
Remove the 7 bolts and continuously variable transaxle assembly from the engine assembly.
To prevent damage to the 2 knock pins, do not pry between the continuously variable transaxle assembly and engine assembly.
Bolt (A), (B): Remove from continuously variable transaxle assembly side.
Bolt (C): Remove from engine assembly side.
32000A
51.REMOVE TORQUE CONVERTER ASSEMBLY
Remove the torque converter assembly from the continuously variable transaxle assembly.
Remove the torque converter assembly from the input shaft horizontally.
30400E
52.REMOVE CVT OIL PUMP TYPE T OIL SEAL
Do not remove the stator shaft assembly from the CVT main body, as there is a possibility of the entry of dust and foreign matter.
Clean the work area, the tools to be used, and other equipment, etc. thoroughly before the operation, as there is the possibility that a CVT malfunction, which could prevent the vehicle from being able to be driven, could occur if dust or fine foreign matter enters the CVT.
Do not use cotton work gloves, cloths, or paper towels, etc. that may produce lint, dust or foreign matter.
Perform the operation as quickly as possible, as dust and foreign matter could enter the CVT while the torque converter assembly is removed.
Do not use an air gun until the torque converter assembly has been installed, as it could cause dust and foreign matter to be stirred up.
Clean the tips of both the claws of SST and the center bolt.
Using SST, remove the CVT type T oil seal.
Pay attention to the angle of the claws when opening them, and ensure that they do not come into contact with the oil pump housing, as there is the possibility that metal particles could be produced if they do.
53.REMOVE WIRE HARNESS CLAMP BRACKET
Remove the 3 bolts and 3 wire harness clamp brackets from the continuously variable transaxle assembly.
35150B
54.REMOVE TRANSMISSION CASE PLUG ASSEMBLY
| *A | for Type A |
| *B | for Type B |
for Type A:
Remove the transmission case plug assembly from the continuously variable transaxle assembly.
Remove the O-ring from the transmission case plug assembly.
for Type B:
Remove the transmission case plug assembly from the continuously variable transaxle assembly.
32000A
55.INSPECT TORQUE CONVERTER ASSEMBLY
32101B
56.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY