Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model) › 2020.09–2021.11
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424994 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  Engine does not Start  


DESCRIPTION

for Manual Transaxle

When the electrical key transmitter sub-assembly is in the cabin and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Additionally, when the clutch pedal is depressed, the engine can be started by pressing the engine switch.


for CVT

When the electrical key transmitter sub-assembly is in the cabin and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Additionally, when the shift lever is in P and the brake pedal is depressed, the engine can be started by pressing the engine switch.


Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Engine does not start
Power Source Control
·

Stop Light Switch*1

·

Shift P Signal*1

·

Neutral SW/ Clutch SW

·

Starter Relay Driving Request (Starting Control)

·

Starter Relay Driving Request (Starting Control)

·

Shift P/N (Starting Control)


Entry&Start
·

Immobiliser

·

Start Request

·

L Code Check

·

S Code Check*2



*1: for CVT

*2: w/o Wireless Door Lock Buzzer Answer-back Function


WIRING DIAGRAM

E446699E02
5.042,2.688 5.5,2.885 0.458,0.198 10 false STA 5.021,1.063 5.479,1.26 0.458,0.198 10 false STAR 5.031,1.74 5.49,1.938 0.458,0.198 10 false STP1 5.75,3.635 6.208,3.833 0.458,0.198 10 false P 6,3.438 6.458,3.635 0.458,0.198 10 false 14 4.74,1.635 5.198,1.833 0.458,0.198 10 false 21 4.729,0.948 5.188,1.146 0.458,0.198 10 false 10 4.76,2.615 5.219,2.813 0.458,0.198 10 false 3 5.656,1.063 6.115,1.26 0.458,0.198 10 false IC 5.667,1.958 6.125,2.156 0.458,0.198 10 false IC 5.656,2.906 6.115,3.104 0.458,0.198 10 false IC 5.083,0.74 5.542,0.938 0.458,0.198 10 false +B 0.531,2.802 0.99,3 0.458,0.198 10 false STA 0.479,1.146 0.938,1.344 0.458,0.198 10 false NSW 0.552,1.729 1.01,1.927 0.458,0.198 10 false STP 0.313,3.542 0.906,3.813 0.594,0.271 10 false ECM 6.594,3.646 7.052,3.844 0.458,0.198 10 false P2 4.573,5.24 5.031,5.438 0.458,0.198 10 false STP 5.656,6.635 6.115,6.833 0.458,0.198 10 false STP 2.604,3.354 3.063,3.552 0.458,0.198 10 false B 3.01,3.354 3.469,3.552 0.458,0.198 10 false L 2.198,3.635 2.656,3.833 0.458,0.198 10 false P 2.188,3.906 2.646,4.104 0.458,0.198 10 false N 1.781,4.271 3.573,4.615 1.792,0.344 10 false Park/Neutral Position Switch 1.448,6.5 2.615,6.823 1.167,0.323 10 false ST NO. 1 0.344,6.094 0.958,6.271 0.615,0.177 10 false ST NO. 1 1.146,7.917 2.635,8.156 1.49,0.24 10 false Starter Assembly 1.052,7.24 1.51,7.438 0.458,0.198 10 false B 2.219,7.417 2.677,7.615 0.458,0.198 10 false ST 6.031,5.188 7.156,5.615 1.125,0.427 10 false Shift Lock Control Unit Assembly 4.469,4.125 6.021,4.594 1.552,0.469 10 false Certification ECU (Smart Key ECU Assembly) 4.813,9.042 6.938,9.354 2.125,0.313 10 false Stop Light Switch Assembly 5.604,8.344 6.063,8.542 0.458,0.198 10 false IC 5.646,7.646 7.125,7.927 1.479,0.281 10 false from Auxiliary Battery 4.615,7.802 5.302,8.01 0.688,0.208 10 false STOP 5.198,8.167 5.656,8.365 0.458,0.198 10 false B 5.208,8.458 6.01,8.667 0.802,0.208 10 false L 6.115,8.667 6.573,8.865 0.458,0.198 10 false GND 4.688,1.156 5.146,1.354 0.458,0.198 10 false H45 5.969,3.635 6.438,3.833 0.469,0.198 10 false H46 0.948,1.031 1.469,1.354 0.521,0.323 10 false 23 0.938,2.677 1.979,2.958 1.042,0.281 10 false 30 0.948,1.719 1.604,1.917 0.656,0.198 10 false 21 0.281,2.01 0.74,2.208 0.458,0.198 10 false IC 2.729,3.115 3.188,3.313 0.458,0.198 10 false 4 1.792,4.125 2.25,4.323 0.458,0.198 10 false D45 4.823,8.875 5.281,9.073 0.458,0.198 10 false A63 1.354,6.115 1.813,6.313 0.458,0.198 10 false 1 2.031,6.104 2.49,6.302 0.458,0.198 10 false 2 2.021,5.844 2.479,6.042 0.458,0.198 10 false 3 1.354,5.854 1.896,6.073 0.542,0.219 10 false 5 0.76,7.042 1.219,7.24 0.458,0.198 10 false 1 0.677,7.25 1.135,7.448 0.458,0.198 10 false D80 2.51,7.448 2.969,7.646 0.458,0.198 10 false D54 4.99,8.458 5.448,8.656 0.458,0.198 10 false 3 4.99,8.083 5.448,8.281 0.458,0.198 10 false 7 6.552,8.573 7.01,8.771 0.458,0.198 10 false 2 2.615,7.229 3.073,7.427 0.458,0.198 10 false 1 6.406,3.531 6.865,3.729 0.458,0.198 10 false 3 6.021,5.031 6.479,5.229 0.458,0.198 10 false H20 4.281,5.177 4.74,5.375 0.458,0.198 10 false 2*3 4.26,5.958 7.063,6.229 2.802,0.271 10 false Skid Control ECU (Brake Actuator Assembly) 4.271,5.802 5.198,6.01 0.927,0.208 10 false A36*2, A37*3 5.156,7.042 5.656,7.333 0.5,0.292 10 false D71 5.167,7.219 6.906,7.458 1.74,0.24 10 false Transmission Control ECU 5.375,6.521 5.74,6.74 0.365,0.219 10 false 43 3.313,3.802 3.771,4 0.458,0.198 10 false 5 4.688,1.844 5.146,2.042 0.458,0.198 10 false H45 4.688,2.792 5.146,2.99 0.458,0.198 10 false H45 0.333,3.375 1.573,3.594 1.24,0.219 10 false A54 0.667,5.438 2.146,5.719 1.479,0.281 10 false from Auxiliary Battery 0.104,0.052 2.208,0.323 2.104,0.271 12 false for CVT: 0.083,4.875 1.323,5.094 1.24,0.219 10 false A67*1 0.073,5.031 1.844,5.229 1.771,0.198 10 false Engine Stop and Start ECU 0.531,4.51 0.99,4.708 0.458,0.198 10 false STA 0.542,4.125 1,4.323 0.458,0.198 10 false CLL 0.906,4.021 1.948,4.302 1.042,0.281 10 false 17 0.917,4.438 1.958,4.719 1.042,0.281 10 false 21 6.583,4.698 7.042,4.896 0.458,0.198 10 false STP 6.406,4.552 6.865,4.75 0.458,0.198 10 false 4 0.365,8.417 2.406,8.615 2.042,0.198 10 false *1: w/ Stop and Start System 1.479,3.531 2.521,3.813 1.042,0.281 10 false *1 2.333,4.646 3.375,4.927 1.042,0.281 10 false *1 4.24,5.021 4.698,5.219 0.458,0.198 10 false 35*2 0.365,8.771 2.406,8.969 2.042,0.198 10 false *2: for TMC Made 0.365,9.125 2.406,9.323 2.042,0.198 10 false *3: for TMMF Made

E452944E01
0.594,1.375 1.052,1.573 0.458,0.198 10 false NSW 0.625,2.188 1.083,2.385 0.458,0.198 10 false STA 0.438,2.76 0.896,2.958 0.458,0.198 10 false ECM 1.063,1.167 1.521,1.365 0.458,0.198 10 false 111 1.094,1.99 1.552,2.188 0.458,0.198 10 false 46 5.865,1.167 6.323,1.365 0.458,0.198 10 false 10 5.823,1.365 6.281,1.563 0.458,0.198 10 false H45 5.823,2.188 6.281,2.385 0.458,0.198 10 false H45 5.896,1.979 6.354,2.177 0.458,0.198 10 false 3 6.177,2.083 6.635,2.281 0.458,0.198 10 false STA 6.156,1.271 6.615,1.469 0.458,0.198 10 false STAR 6.219,0.948 6.677,1.146 0.458,0.198 10 false +B 6.792,1.25 7,1.49 0.208,0.24 10 false IC 6.792,2.313 7,2.552 0.208,0.24 10 false IC 2.5,3.229 2.958,3.427 0.458,0.198 10 false A64 2.49,3.396 4.552,3.677 2.063,0.281 10 false Clutch Start Switch Assembly 2.781,2.927 3.24,3.125 0.458,0.198 10 false 2 3.833,2.927 4.292,3.125 0.458,0.198 10 false 1 3.625,2.948 4.083,3.146 0.458,0.198 10 false L 3,2.958 3.458,3.156 0.458,0.198 10 false B 5.625,3.531 7.146,4 1.521,0.469 10 false Certification ECU (Smart Key ECU Assembly) 1.521,5.948 2.365,6.302 0.844,0.354 10 false ST NO. 1 2.073,5.563 2.333,5.74 0.26,0.177 10 false 2 2.073,5.313 2.333,5.49 0.26,0.177 10 false 3 1.438,5.563 1.698,5.74 0.26,0.177 10 false 1 1.438,5.292 1.698,5.469 0.26,0.177 10 false 5 0.375,5.542 1.094,5.781 0.719,0.24 10 false ST NO. 1 0.74,6.719 1.094,6.917 0.354,0.198 10 false D80 2.573,6.896 2.927,7.094 0.354,0.198 10 false D54 2.281,6.896 2.635,7.094 0.354,0.198 10 false ST 1.104,6.719 1.458,6.917 0.354,0.198 10 false B 0.813,6.51 1.167,6.708 0.354,0.198 10 false 1 2.646,6.698 3,6.896 0.354,0.198 10 false 1 1.229,7.344 2.563,7.615 1.333,0.271 10 false Starter Assembly 0.719,4.906 2.229,5.146 1.51,0.24 10 false from Auxiliary Battery 0.115,0.083 3.219,0.313 3.104,0.229 12 false for Manual Transaxle with 1KR-FE: 0.229,4.313 0.688,4.51 0.458,0.198 10 false A67*1 0.219,4.469 1.99,4.698 1.771,0.229 10 false Engine Stop and Start ECU 0.698,4 1.156,4.198 0.458,0.198 10 false STA 0.698,3.604 1.156,3.802 0.458,0.198 10 false CLL 1.052,3.479 1.51,3.677 0.458,0.198 10 false 17 1.052,3.885 1.51,4.083 0.458,0.198 10 false 21 1.729,3.479 2.188,3.677 0.458,0.198 10 false *1 1.729,3.885 2.188,4.083 0.458,0.198 10 false *1 4.396,6.542 6.448,6.75 2.052,0.208 10 false *1: w/ Stop and Start System 1.052,1.375 1.51,1.573 0.458,0.198 10 false D50 1.052,2.188 1.51,2.385 0.458,0.198 10 false A55

E452945E01
0.583,1.375 1.042,1.573 0.458,0.198 10 false NSW 0.635,2.188 1.094,2.385 0.458,0.198 10 false STA 0.375,2.75 1.49,2.99 1.115,0.24 10 false A54*2, A106*3 0.375,2.917 0.833,3.115 0.458,0.198 10 false ECM 1.042,1.271 1.5,1.469 0.458,0.198 10 false 23 1.021,2.083 1.479,2.281 0.458,0.198 10 false 30 5.865,1.167 6.323,1.365 0.458,0.198 10 false 10 5.823,1.365 6.281,1.563 0.458,0.198 10 false H45 5.833,2.177 6.292,2.375 0.458,0.198 10 false H45 5.896,1.969 6.354,2.167 0.458,0.198 10 false 3 6.177,2.083 6.635,2.281 0.458,0.198 10 false STA 6.156,1.271 6.615,1.469 0.458,0.198 10 false STAR 6.219,0.948 6.677,1.146 0.458,0.198 10 false +B 6.792,1.25 7,1.49 0.208,0.24 10 false IC 6.792,2.313 7,2.552 0.208,0.24 10 false IC 2.375,3.281 2.833,3.479 0.458,0.198 10 false A64 2.365,3.438 4.427,3.719 2.063,0.281 10 false Clutch Start Switch Assembly 2.656,2.938 3.115,3.135 0.458,0.198 10 false 2 3.667,2.938 4.125,3.135 0.458,0.198 10 false 1 3.458,2.958 3.917,3.156 0.458,0.198 10 false L 2.865,2.958 3.323,3.156 0.458,0.198 10 false B 5.604,3.521 7.146,4.031 1.542,0.51 10 false Certification ECU (Smart Key ECU Assembly) 1.51,5.938 2.354,6.292 0.844,0.354 10 false ST NO. 1 2.073,5.563 2.333,5.74 0.26,0.177 10 false 2 2.073,5.313 2.333,5.49 0.26,0.177 10 false 3 1.438,5.563 1.698,5.74 0.26,0.177 10 false 1 1.438,5.292 1.698,5.469 0.26,0.177 10 false 5 0.375,5.542 1.094,5.781 0.719,0.24 10 false ST NO. 1 1.094,6.708 1.448,6.906 0.354,0.198 10 false D80 2.99,6.906 3.344,7.104 0.354,0.198 10 false D54 2.677,6.906 3.031,7.104 0.354,0.198 10 false ST 1.5,6.719 1.854,6.917 0.354,0.198 10 false B 1.156,6.51 1.51,6.708 0.354,0.198 10 false 1 3.052,6.677 3.406,6.875 0.354,0.198 10 false 1 1.667,7.375 3,7.646 1.333,0.271 10 false Starter Assembly 0.719,4.906 2.229,5.146 1.51,0.24 10 false from Auxiliary Battery 0.115,0.083 3.156,0.438 3.042,0.354 12 false for Manual Transaxle without 1KR-FE: 0.229,4.313 0.688,4.51 0.458,0.198 10 false A67*1 0.219,4.469 1.99,4.698 1.771,0.229 10 false Engine Stop and Start ECU 0.698,4 1.156,4.198 0.458,0.198 10 false STA 0.698,3.604 1.156,3.802 0.458,0.198 10 false CLL 1.052,3.479 1.51,3.677 0.458,0.198 10 false 17 1.052,3.885 1.51,4.083 0.458,0.198 10 false 21 1.729,3.479 2.188,3.677 0.458,0.198 10 false *1 1.729,3.885 2.188,4.083 0.458,0.198 10 false *1 4.396,6.542 6.448,6.75 2.052,0.208 10 false *1: w/ Stop and Start System 4.396,6.833 6.448,7.042 2.052,0.208 10 false *2: for M15A-FKS 4.396,7.125 6.448,7.333 2.052,0.208 10 false *3: for G16E-GTS 0.594,6.708 0.948,6.906 0.354,0.198 10 false D108 0.677,6.5 1.031,6.698 0.354,0.198 10 false 1 1.125,6.917 1.479,7.115 0.354,0.198 10 false *2 0.635,6.917 0.99,7.115 0.354,0.198 10 false *3

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

If the entry and start system (for Start Function) has been disabled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>CUSTOMIZE PARAMETERS

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to Service Bulletin.

·

After completing repairs, confirm that the problem does not recur.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for CVT A
for Manual Transaxle B



A

2.CHECK ENGINE SWITCH CONDITION

B

28.CHECK ENGINE SWITCH CONDITION
2.CHECK ENGINE SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

With the brake pedal released, check that pressing the engine switch causes the power source mode to change.


Result:
Result Proceed to
Power source mode changes : Off → ACC → ON → off A
Power source mode does not change to ACC or ON B
Power source mode changes to ON but not to ACC C
Power source mode changes to ACC but not to ON D



A

3.READ VALUE USING GTS (STOP LIGHT SWITCH)

B

C

D

3.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch State of brake pedal OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine if the stop light switch assembly is malfunctioning.

·

The engine cannot be started when this item is OFF.

·

If the stop light switch assembly is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch
50003 454 206
OK:

The GTS display changes correctly in response to the brake pedal operation.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (SHIFT P SIGNAL)

NG

25.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - AUXILIARY BATTERY AND GROUND)
4.READ VALUE USING GTS (SHIFT P SIGNAL)
a.

Move the shift lever to P.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P Signal Shift position P OFF or ON OFF: Shift lever not in P
ON: Shift lever in P
·

Use this item to determine if the shift position switch is malfunctioning.

·

The engine cannot be started when this item is OFF.


Body Electrical > Power Source Control > Data List
Tester Display
Shift P Signal
50003 454 205
OK:

ON is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT P/N (STARTING CONTROL))

NG

22.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY
5.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT P/N (STARTING CONTROL))
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Switch / Clutch Switch Shift position (P and N) OFF or ON OFF: Shift lever in any position other than P or N
ON: Shift lever in P or N
·

Use this item to determine if the park/neutral position switch assembly is malfunctioning.

·

When the engine cannot be started due to a park/neutral position switch assembly malfunction, OFF is displayed.


Body Electrical > Power Source Control > Data List
Tester Display
Neutral Switch / Clutch Switch
50003 454 207
Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P/N (Starting Control) Park/Neutral position switch status OFF or ON OFF: Shift lever not in P or N
ON: Shift lever in P or N
When OFF is displayed, the engine will not crank.
Body Electrical > Power Source Control > Data List
Tester Display
Shift P/N (Starting Control)
50003 454 703
OK:

The GTS display changes correctly in response to the shift lever operation.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (POWER SUPPLY CONDITION)

NG

15.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW)
6.READ VALUE USING GTS (POWER SUPPLY CONDITION)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state OFF, ACC ON, IGR ON, IGP ON or Starter ON OFF: Ignition switch off
ACC ON: Ignition switch ACC
IGR ON: Ignition switch ON
IGP ON: Ignition switch ON
Starter ON: Sending engine start request signal
-
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 454 405
NOTICE:

Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the engine switch.


OK:

The GTS display changes correctly in response to the engine switch operation.



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)

NG

13.CHECK STEERING LOCK FUNCTION
7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)
a.
C378519C11
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 No. 1 Engine Room Relay Block Assembly
(ST NO. 1 Relay Holder)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 1 engine room relay block assembly ST NO. 1 relay terminal 2 - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the auxiliary battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - AUXILIARY BATTERY AND GROUND)

NG

12.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST NO. 1 RELAY)
8.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - AUXILIARY BATTERY AND GROUND)
a.
C378519C11
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 No. 1 Engine Room Relay Block Assembly
(ST NO. 1 Relay Holder)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 1 engine room relay block assembly ST NO. 1 relay terminal 1 - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 1 engine room relay block assembly ST NO. 1 relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.INSPECT ST NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT ST NO. 1 RELAY

OK

10.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST NO. 1 RELAY)

NG

REPLACE ST NO. 1 RELAY

10.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST NO. 1 RELAY)
a.

Disconnect the D54 starter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 1 engine room relay block assembly ST NO. 1 relay terminal 3 - D54-1 Always Below 1 Ω
No. 1 engine room relay block assembly ST NO. 1 relay terminal 3 or D54-1 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - AUXILIARY BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - AUXILIARY BATTERY)
a.

Disconnect the D80 starter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D80-1 (B) - Body ground Always 11 to 14 V



Result:
Result Proceed to
OK (w/ Stop And Start System) A
OK (w/o Stop And Start System) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST NO. 1 RELAY)
a.

Disconnect the D45 park/neutral position switch assembly connector.


b.

Disconnect the A67 engine stop and start ECU connector.*1

*1: w/ Stop and Start System



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D45-5 (L) - No. 1 engine room relay block assembly ST NO. 1 relay terminal 2 Always Below 1 Ω
D45-5 (L) or No. 1 engine room relay block assembly ST NO. 1 relay terminal 2 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK STEERING LOCK FUNCTION
a.

Check that the steering unlocks when the ignition switch is turned to ACC.

OK:

The steering unlocks.



Result:
Proceed to
OK
NG



OK

14.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER FUNCTION UNSET)

NG

14.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER FUNCTION UNSET)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

Press the engine switch with the brake pedal released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.

OK:

The security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.


HINT:

The immobiliser function can be determined to be operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

15.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW)
a.

Disconnect the A54 ECM connector.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Switch / Clutch Switch Shift position (P and N) OFF or ON OFF: Shift lever in any position other than P or N
ON: Shift lever in P or N
·

Use this item to determine if the park/neutral position switch assembly is malfunctioning.

·

When the engine cannot be started due to a park/neutral position switch assembly malfunction, OFF is displayed.


Body Electrical > Power Source Control > Data List
Tester Display
Neutral Switch / Clutch Switch
50003 454 207
OK:

The GTS display changes correctly in response to the shift lever operation.



Result:
Proceed to
OK
NG



OK

NG

16.CONFIRM MODEL
16.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Stop And Start System A
w/o Stop And Start System B



A

17.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW)

B

18.INSPECT PARK/NEUTRAL POSITION SWITCH
17.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW)
a.

Disconnect the A67 engine stop and start ECU connector.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Switch / Clutch Switch Shift position (P and N) OFF or ON OFF: Shift lever in any position other than P or N
ON: Shift lever in P or N
·

Use this item to determine if the park/neutral position switch assembly is malfunctioning.

·

When the engine cannot be started due to a park/neutral position switch assembly malfunction, OFF is displayed.


Body Electrical > Power Source Control > Data List
Tester Display
Neutral Switch / Clutch Switch
50003 454 207
OK:

The GTS display changes correctly in response to the shift lever operation.



Result:
Proceed to
OK
NG



OK

NG

18.INSPECT PARK/NEUTRAL POSITION SWITCH
18.INSPECT PARK/NEUTRAL POSITION SWITCH

OK

19.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

19.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)
a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the D45 park/neutral position switch connector.


c.

Remove the ST NO. 1 relay.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-3 (STA) - D45-5 (L) Always Below 1 Ω
H45-3 (STA) - A67-21 (STA)*1 Always Below 1 Ω
H45-10 (STAR) - A54-23 (NSW) Always Below 1 Ω
H45-10 (STAR) - D45-4 (B) Always Below 1 Ω
H45-10 (STAR) - A67-17 (CLL)*1 Always Below 1 Ω
H45-3 (STA) or D45-5 (L) - Other terminals and body ground Always 10 kΩ or higher
H45-10 (STAR) or A54-23 (NSW) - Other terminals and body ground Always 10 kΩ or higher
H45-10 (STAR) or D45-4 (B) - Other terminals and body ground Always 10 kΩ or higher


*1: w/ Stop And Start System



Result:
Proceed to
OK
NG



OK

20.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the H45 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H45-10 (STAR) - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the auxiliary battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

21.INSPECT ST NO. 1 RELAY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

21.INSPECT ST NO. 1 RELAY

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE ST NO. 1 RELAY

22.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H46-14 (P) - Body ground Shift position P → Shift position not P 9V or higher → 2.76 V or less



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

23.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SHIFT LOCK CONTROL UNIT ASSEMBLY)
23.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the H20 shift lock control unit assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-14 (P) - H20-3 (P2) Always Below 1 Ω
H46-14 (P) or H20-3 (P2) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

24.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY
a.

Reconnect the H46 certification ECU (smart key ECU assembly) connector.

Standard Voltage:
Tester Connection Condition Specified Condition
H46-14 (P) - Body ground Shift position P 9 V or higher



Result:
Result Proceed to
OK (for TMC Made) A
OK (for TMMF Made) B
NG C



A

REPLACE SHIFT CONTROL UNIT ASSEMBLY

B

REPLACE SHIFT CONTROL UNIT ASSEMBLY

C

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

25.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - AUXILIARY BATTERY AND GROUND)
a.

Disconnect the A63 stop light switch assembly connector.


b.
E409581C46
1.458,0.094 1.958,0.344 0.5,0.25 2.625,1.917 2.458,1.917 2.458,1.917 2.313,1.344 true 0.979,1.896 1.146,1.896 1.146,1.896 1.313,1.365 true 0.115,0.125 0.427,0.281 0.313,0.156 10 false *a 1.594,0.146 1.906,0.302 0.313,0.156 10 false A63 2.698,1.833 3.01,1.99 0.313,0.156 10 false B 0.698,1.823 1.01,1.979 0.313,0.156 10 false GND
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A63-7 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A63-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

26.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.INSPECT STOP LIGHT SWITCH ASSEMBLY

OK

27.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

27.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Disconnect the A54 ECM connector.


d.

Disconnect the A36*1 or A37*2 skid control ECU (brake actuator assembly) connector.


e.

Disconnect the D71 transmission control ECU connector.


f.

Disconnect the H20 shift lock control unit assembly connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-21 (STP1) - A63-3 (L) Always Below 1 Ω
H45-21 (STP1) or A63-3 (L) - Other terminals and body ground Always 10 kΩ or higher


*1: for TMC Made

*2: for TMMF Made



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

28.CHECK ENGINE SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

With the clutch pedal released, check that pressing the engine switch causes the power source mode to change.


Result:
Result Proceed to
Power source mode changes : Off → ACC → ON → off A
Power source mode does not change to ACC or ON B
Power source mode changes to ON but not to ACC C
Power source mode changes to ACC but not to ON D



A

29.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW)

B

C

D

29.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Switch / Clutch Switch State of clutch pedal OFF or ON OFF: Clutch pedal released
ON: Clutch pedal depressed
·

Use this item to help determine if the clutch position switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".


Body Electrical > Power Source Control > Data List
Tester Display
Neutral Switch / Clutch Switch
50003 454 207
OK:

The GTS display changes correctly in response to the clutch pedal operation.



Result:
Proceed to
OK
NG



OK

30.READ VALUE USING GTS (POWER SUPPLY CONDITION)

NG

39.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW)
30.READ VALUE USING GTS (POWER SUPPLY CONDITION)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state OFF, ACC ON, IGR ON, IGP ON or Starter ON OFF: Ignition switch off
ACC ON: Ignition switch ACC
IGR ON: Ignition switch ON
IGP ON: Ignition switch ON
Starter ON: Sending engine start request signal
-
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 454 405
NOTICE:

Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the engine switch.


OK:

The GTS display changes correctly in response to the engine switch operation.



Result:
Proceed to
OK
NG



OK

31.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)

NG

37.CHECK STEERING LOCK FUNCTION
31.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)
a.
C378519C11
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 No. 1 Engine Room Relay Block Assembly
(ST NO. 1 Relay Holder)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 1 engine room relay block assembly ST NO. 1 relay terminal 2 - Body ground Engine switch pressed and held with clutch pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the auxiliary battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

32.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - AUXILIARY BATTERY AND GROUND)

NG

36.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ST NO. 1 RELAY)
32.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - AUXILIARY BATTERY AND GROUND)
a.
C378519C11
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 No. 1 Engine Room Relay Block Assembly
(ST NO. 1 Relay Holder)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 1 engine room relay block assembly ST NO. 1 relay terminal 1 - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 1 engine room relay block assembly ST NO. 1 relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

33.INSPECT ST NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

33.INSPECT ST NO. 1 RELAY

OK

34.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST NO. 1 RELAY)

NG

REPLACE ST NO. 1 RELAY

34.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST NO. 1 RELAY)
a.

Disconnect the D54 starter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 1 engine room relay block assembly ST NO. 1 relay terminal 3 - D54-1 Always Below 1 Ω
No. 1 engine room relay block assembly ST NO. 1 relay terminal 3 or D54-1 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

35.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - AUXILIARY BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

35.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - AUXILIARY BATTERY)
a.

Disconnect the D80*1 or D108*2 starter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D80-1 (B) - Body ground*1 Always 11 to 14 V
D108-1 (B) - Body ground*2 Always 11 to 14 V



*1: except G16E-GTS

*2: for G16E-GTS


Result:
Result Proceed to
OK (for M15A-FKS with Stop And Start System) A
OK (for M15A-FKS without Stop And Start System) B
OK (for 1KR-FE with Stop And Start System) C
OK (for 1KR-FE without Stop And Start System) D
OK (for G16E-GTS) E
NG F



A

B

C

D

E

F

REPAIR OR REPLACE HARNESS OR CONNECTOR

36.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ST NO. 1 RELAY)
a.

Disconnect the A64 clutch start switch assembly connector.


b.

Disconnect the A67 engine stop and start ECU connector.*1

*1: w/ Stop and Start System



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-1 (L) - 2 (ST NO. 1 relay) Always Below 1 Ω
A64-1 (L) or 2 (ST NO. 1 relay) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

37.CHECK STEERING LOCK FUNCTION
a.

Check that the steering unlocks when the ignition switch is turned to ACC.

OK:

The steering unlocks.



Result:
Proceed to
OK
NG



OK

38.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER FUNCTION UNSET)

NG

38.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER FUNCTION UNSET)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Press the engine switch with the clutch pedal released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.

OK:

The security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.


HINT:

The immobiliser function can be determined to be operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

39.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW)
a.

Disconnect the A55 and D50 ECM connector.*1


b.

Disconnect the A54 ECM connector.*2


c.

Disconnect the A106 ECM connector.*3


*1: for 1KR-FE

*2: for M15A-FKS

*3: for G16E-GTS


d.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Switch / Clutch Switch State of clutch pedal OFF or ON OFF: Clutch pedal released
ON: Clutch pedal depressed
·

Use this item to help determine if the clutch position switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".


Body Electrical > Power Source Control > Data List
Tester Display
Neutral Switch / Clutch Switch
50003 454 207
OK:

The GTS display changes correctly in response to the clutch pedal operation.



Result:
Result Proceed to
OK (for M15A-FKS) A
OK (for G16E-GTS) B
OK (for 1KR-FE) C
NG D



A

B

C

D

40.CONFIRM MODEL
40.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Stop And Start System A
w/o Stop And Start System B



A

41.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW)

B

42.INSPECT CLUTCH START SWITCH ASSEMBLY
41.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW)
a.

Disconnect the A67 engine stop and start ECU connector.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Switch / Clutch Switch State of clutch pedal OFF or ON OFF: Clutch pedal released
ON: Clutch pedal depressed
·

Use this item to help determine if the clutch position switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".


Body Electrical > Power Source Control > Data List
Tester Display
Neutral Switch / Clutch Switch
50003 454 207
OK:

The GTS display changes correctly in response to the clutch pedal operation.



Result:
Proceed to
OK
NG



OK

NG

42.INSPECT CLUTCH START SWITCH ASSEMBLY
42.INSPECT CLUTCH START SWITCH ASSEMBLY

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION

Result:
Proceed to
OK
NG



OK

43.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)

NG

REPLACE CLUTCH START SWITCH ASSEMBLY)

43.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A64 clutch start switch assembly connector.


c.

Remove the ST NO. 1 relay.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-3 (STA) - A64-1 (L) Always Below 1 Ω
H45-3 (STA) - A67-21 (STA)*4 Always Below 1 Ω
H45-10 (STAR) - D50-111 (NSW)*1 Always Below 1 Ω
H45-10 (STAR) - A54-23 (NSW)*2 Always Below 1 Ω
H45-10 (STAR) - A106-23 (NSW)*3 Always Below 1 Ω
H45-10 (STAR) - A64-2 (B) Always Below 1 Ω
H45-10 (STAR) - A67-17 (CLL)*4 Always Below 1 Ω
H45-3 (STA) or A64-1 (L) - Other terminals and body ground Always 10 kΩ or higher
H45-10 (STAR) or D50-111 (NSW) - Other terminals and body ground*1 Always 10 kΩ or higher
H45-10 (STAR) or A54-23 (NSW) - Other terminals and body ground*2 Always 10 kΩ or higher
H45-10 (STAR) or A106-23 (NSW) - Other terminals and body ground*3 Always 10 kΩ or higher
H45-10 (STAR) or A64-2 (B) - Other terminals and body ground Always 10 kΩ or higher


*1: for 1KR-FE

*2: for M15A-FKS

*3: for G16E-GTS

*4: w/ Stop And Start System



Result:
Proceed to
OK
NG



OK

44.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

44.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the H45 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H45-10 (STAR) - Body ground Engine switch pressed and held with clutch pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the auxiliary battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

45.INSPECT ST NO. 1 RELAY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

45.INSPECT ST NO. 1 RELAY

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE ST NO. 1 RELAY