13050
1.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
13070A
2.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
13050
3.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY
Fix the camshaft in place.
Be careful not to damage the camshaft.
Put the camshaft timing gear assembly and camshaft together by aligning the pin hole and straight pin.
| *1 | Pin Hole |
| *2 | Straight Pin |
Lightly press and turn the camshaft timing gear assembly against the camshaft, and press harder after the pin enters the hole.
Be sure not to turn the camshaft timing gear assembly in the retard direction.
Check that there is no clearance between the camshaft timing gear assembly flange and camshaft.
Install the flange bolt while holding the camshaft.
Check the lock of the camshaft timing gear assembly.
Fix the camshaft in place and confirm that the camshaft timing gear assembly is locked.
Be careful not to damage the camshaft.
13070A
4.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
Fix the camshaft in place.
Be careful not to damage the camshaft.
Put the camshaft timing exhaust gear assembly and camshaft together by aligning the pin hole and straight pin.
| *1 | Pin Hole |
| *2 | Straight Pin |
Lightly press and turn the camshaft timing gear assembly against the camshaft, and press harder after the pin enters the hole.
Be sure not to turn the camshaft timing exhaust gear assembly in the advanced direction.
Check that there is no clearance between the gear flange and camshaft.
Install the flange bolt while holding the camshaft.
Check the lock of the camshaft timing exhaust gear assembly.
Make sure that the camshaft timing exhaust gear assembly locks.
13053
5.INSTALL NO. 3 CAMSHAFT
Check that the notch is aligned with the "0" timing mark of the timing chain cover sub-assembly.
Align the mark plate (yellow) with the timing mark of the camshaft timing gear assembly as shown in the illustration and install the No. 2 chain sub-assembly to the camshaft timing gear assembly.
| *1 | Timing Mark |
| *2 | Mark Plate (yellow) |
| *a | Align |
Clean the camshaft housing LH and camshaft journals and apply engine oil to them.
Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.
| *1 | No. 1 Valve Rocker Arm Sub-assembly |
| *2 | Valve Lash Adjuster Assembly |
| *3 | Valve Stem |
| *4 | Valve Stem Cap |
Install the chain sub-assembly to the No. 3 camshaft, and then install the No. 3 camshaft to the camshaft housing LH.
| *a | Place on camshaft timing gear |
Place the chain sub-assembly on the camshaft timing gear assembly but do not engage the teeth of the sprocket and the chain sub-assembly.
Install the No. 3 camshaft so that the timing mark is facing upward.
13054
6.INSTALL NO. 4 CAMSHAFT
Clean the camshaft housing LH and camshaft journals and apply engine oil to them.
Pass the No. 4 camshaft through the No. 2 chain sub-assembly from the front of the vehicle, align the mark plate (yellow) with the timing mark and install the No. 2 chain sub-assembly to the camshaft timing exhaust gear assembly.
| *1 | Mark Plate (yellow) |
| *2 | Timing Mark |
While lifting up the No. 4 camshaft, pass the No. 3 chain tensioner assembly through the No. 2 chain and set it in place.
Install the No. 4 camshaft to the camshaft housing LH, and then install the No. 3 chain tensioner assembly with the bolt.
7.INSTALL CAMSHAFT BEARING CAP (for Bank 2)
Clean the camshaft bearing caps and apply engine oil to them.
Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.
| *1 | No. 1 Valve Rocker Arm Sub-assembly |
| *2 | Valve Lash Adjuster Assembly |
| *3 | Valve Stem |
| *4 | Valve Stem Cap |
Check the marks and numbers on the camshaft bearing caps, and then remove the replacement bolts and washers in the order shown in the illustration. Immediately after removing the bolts and washers for temporary installation of the camshaft housing in the location for a bearing cap, install the bearing cap with the bolts in the order shown in the illustration.
| *1 | Bolt |
| *2 | Washer |
| *a | Installation of Bolts and Washers for Temporary Installation of camshaft housing |
| *b | Part Installation |
|
Bolt A |
|
Bolt B |
Be sure to follow the numerical order when performing this procedure.
Do not drop bolts and washers for temporary installation of the camshaft housing into the cylinder head.
Check the torque of each bolt again.
13506
8.CONNECT CHAIN SUB-ASSEMBLY (for Bank 2)
Align the paint marks on the camshaft timing gear assembly and No. 1 chain sub-assembly and install the No. 1 chain sub-assembly to the camshaft timing gear assembly.
| *1 | Paint Mark |
If the paint marks are not aligned, align them by turning the camshaft slightly.
13511
9.INSTALL CAMSHAFT
Turn the crankshaft clockwise until it is in the position shown in the illustration so that the chain sub-assembly can be installed easily.
When turning the crankshaft, engine oil may spray out of the oil holes.
Align the mark plate (yellow) with the timing mark of the camshaft timing gear assembly as shown in the illustration and install the No. 2 chain sub-assembly to the camshaft timing gear assembly.
| *1 | Timing Mark |
| *2 | Mark Plate (yellow) |
| *a | Align |
Clean the camshaft housing RH and camshaft journals and apply engine oil to them.
Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.
| *1 | No. 1 Valve Rocker Arm Sub-assembly |
| *2 | Valve Lash Adjuster Assembly |
| *3 | Valve Stem |
| *4 | Valve Stem Cap |
Install the chain sub-assembly to the camshaft, and then install the camshaft to the camshaft housing RH.
| *a | Place on camshaft timing gear assembly |
Place the chain sub-assembly on the camshaft timing gear assembly but do not engage the teeth of the sprocket and the chain sub-assembly.
Install the camshaft so that the timing mark is facing upward.
13512
10.INSTALL NO. 2 CAMSHAFT
Clean the camshaft housing RH and camshaft journals and apply engine oil to them.
Pass the No. 2 camshaft through the No. 2 chain sub-assembly from the front of the vehicle, align the mark plate (yellow) with the timing mark and install the No. 2 chain sub-assembly to the camshaft timing exhaust gear assembly.
| *1 | Mark Plate (yellow) |
| *2 | Timing Mark |
While lifting up the No. 2 camshaft, pass the No. 2 chain tensioner assembly through the No. 2 chain sub-assembly and set it in place.
Install the No. 2 camshaft to the camshaft housing RH, and then install the No. 2 chain tensioner assembly with the bolt.
11.INSTALL CAMSHAFT BEARING CAP (for Bank 1)
Clean the camshaft bearing caps and apply engine oil to them.
Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.
| *1 | Valve Rocker Arm |
| *2 | Lash Adjuster |
| *3 | Valve Stem |
| *4 | Valve Stem Cap |
Check the marks and numbers on the camshaft bearing caps, and then remove the replacement bolts and washers in the order shown in the illustration. Immediately after removing the bolts and washers for temporary installation of the camshaft housing in the location for a bearing cap, install the bearing cap with the bolts in the order shown in the illustration.
| *1 | Bolt |
| *2 | Washer |
| *a | Installation of Bolts and Washers for Temporary Installation of camshaft housing |
| *b | Part Installation |
|
Bolt A |
|
Bolt B |
Be sure to follow the numerical order when performing this procedure.
Do not drop bolts and washers for temporary installation of the camshaft housing into the cylinder head.
Check the torque of each bolt again.
13506
12.CONNECT CHAIN SUB-ASSEMBLY (for Bank 1)
Align the paint marks on the camshaft timing gear assembly and chain sub-assembly and install the chain sub-assembly to the camshaft timing gear.
| *1 | Paint Mark |
If the paint marks are not aligned, align them by turning the camshaft slightly.
13540
13.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
Turn the crankshaft counterclockwise 30° past the "0" timing mark, and then turn it clockwise to align the notch with the "0" timing mark.
Turn the crankshaft slightly to eliminate the slack in the chain sub-assembly.
Make sure there is some slack in the chain sub-assembly around the area where the No. 1 chain tensioner assembly is installed.
While turning the stopper plate of the No. 1 chain tensioner assembly clockwise, push in the plunger of the No. 1 chain tensioner assembly as shown in the illustration.
| *1 | Stopper Plate |
| *a | Push |
While turning the stopper plate of the No. 1 chain tensioner assembly counterclockwise, insert a pin of φ1.27 mm (0.0500 in.) into the holes in the stopper plate and No. 1 chain tensioner assembly to fix the stopper plate in place.
Install the No. 1 chain tensioner assembly with the 2 bolts.
Remove the pin from the No. 1 chain tensioner assembly.
14.INSPECT VALVE TIMING
Check the camshaft timing marks.
Check each timing mark from a viewpoint directly in line with the center of the camshaft and the timing mark on each camshaft timing gear assembly.
If the timing marks are checked from any other viewpoint, the valve timing may appear misaligned.
Check that each camshaft timing mark is positioned as shown in the illustration.
| *1 | Timing Mark | - | - |
| *a | Viewpoint | - | - |
for Intake Camshaft:
Be sure to check mark A at the point when marks B, C and D are positioned in line. If the marks are checked from any other viewpoint, they cannot be checked correctly.
If the valve timing is misaligned, reinstall the chain sub-assembly.
Turn the crankshaft 2 revolutions, set the No. 1 cylinder to TDC/compression and check the timing marks again.
11324
15.INSTALL TIMING CHAIN COVER PLATE
Install a new gasket and the timing chain cover plate with the 4 bolts.
16.POUR ENGINE OIL
11201
17.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
11202
18.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
19.CONNECT FUEL PIPE SUB-ASSEMBLY
11181A
20.INSTALL REAR CYLINDER HEAD COVER
15772
21.INSTALL NO. 2 OIL PIPE
15771
22.INSTALL NO. 1 OIL PIPE
16206
23.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY
11452
24.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
27020
25.INSTALL GENERATOR ASSEMBLY
17168
26.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
82715
27.INSTALL WIRING HARNESS CLAMP BRACKET
16604
28.INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY
44310
29.CONNECT VANE PUMP ASSEMBLY
19500
30.INSTALL IGNITION COIL ASSEMBLY
25702B
31.INSTALL NO. 2 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)
25701B
32.INSTALL NO. 1 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)
17362
33.INSTALL NO. 2 AIR TUBE (w/ Secondary Air Injection System)
17361
34.INSTALL AIR TUBE (w/ Secondary Air Injection System)
17129
35.INSTALL INTAKE AIR SURGE TANK
17360G
36.INSTALL AIR TUBE ASSEMBLY (w/ Secondary Air Injection System)
16711
37.INSTALL FAN SHROUD
32907C
38.CONNECT OIL COOLER TUBE
16470
39.INSTALL RADIATOR RESERVOIR TANK
16572
40.INSTALL NO. 2 RADIATOR HOSE
16571
41.INSTALL NO. 1 RADIATOR HOSE
42.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
43.INSTALL AIR CLEANER CAP AND HOSE
74431
44.INSTALL BATTERY TRAY
28800
45.INSTALL BATTERY
74481A
46.INSTALL BATTERY HOLD DOWN CLAMP
28800A
47.CONNECT CABLE TO POSITIVE BATTERY TERMINAL
48.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
49.ADD ENGINE COOLANT
50.ADD ENGINE OIL
51.INSPECT FOR COOLANT LEAK
52.INSPECT FOR ENGINE OIL LEAK
11259
53.INSTALL V-BANK COVER
53292A
54.INSTALL UPPER RADIATOR SUPPORT SEAL
51405A
55.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
52129B
56.INSTALL FRONT BUMPER LOWER COVER (w/o TOYOTA Parking Assist-sensor System)
52822
57.INSTALL AIR INTAKE DUCT LH (w/ TOYOTA Parking Assist-sensor System)
52821
58.INSTALL AIR INTAKE DUCT RH (w/ TOYOTA Parking Assist-sensor System)
52129B
59.INSTALL FRONT BUMPER LOWER COVER (w/ TOYOTA Parking Assist-sensor System)
53298
60.INSTALL COOL AIR INTAKE DUCT (for 4WD with TOYOTA Parking Assist-sensor System)
61.INSPECT IGNITION TIMING