Home › Engine / Hybrid System › FA20 (ENGINE MECHANICAL) › ENGINE › from 2019.03
RM2090E _51 Engine / Hybrid System _060666 FA20 ENGINE MECHANICAL _0297487 ENGINE G

FA20 ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 17801 4.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 16620 6.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY

a.

Remove the fan and generator V belt.

Click hereEngine / Hybrid System>FA20 (ENGINE MECHANICAL)>DRIVE BELT>REMOVAL


b.

Check that nothing gets caught in the tensioner by turning it clockwise and counterclockwise.

If a any malfunction exists, replace the tensioner.


c.

Install the fan and generator V belt.

Click hereEngine / Hybrid System>FA20 (ENGINE MECHANICAL)>DRIVE BELT>INSTALLATION


Hide 7.INSPECT IGNITION TIMING

a.

Warm up and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Start the engine and idle it.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.

Standard ignition timing:

-5 to 10° BTDC at idle


NOTICE:
·

Switch off all the accessories and the A/C before connecting the GTS.

·

When checking the idle speed, the transmission should be in neutral.



HINT:

Refer to the GTS operator's manual for further details.



v.

Check that the ignition timing advances immediately when the engine speed is increased.



c.

When not using the GTS:

i.
A281492

Connect the tester probe of a timing light to the wire of the ignition connector for the No. 1 cylinder.

HINT:

Use a timing light that detects the primary current.



ii.
A276027

Using the timing light, check the ignition timing.

Standard ignition timing:

-5 to 10° BTDC at idle


NOTICE:

When checking the ignition timing, the transmission should be in neutral.



iii.

Check that the ignition timing advances immediately when the engine speed is increased.


iv.

Disconnect the timing light from the engine.



Hide 8.INSPECT ENGINE IDLE SPEED

a.

Warm up and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.

NOTICE:

Switch off all the accessories and the A/C before connecting the GTS.



ii.

Race the engine at 2500 rpm for approximately 90 seconds.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Standard Idle Speed:
Transmission Idling Speed
for Automatic Transmission 600 to 800 rpm
for Manual Transmission 550 to 750 rpm

NOTICE:

When checking the idle speed, the transmission should be in neutral.


HINT:

Refer to the GTS operator's manual for further details.


If the idle speed is not as specified, check the air intake system.


v.

Disconnect the GTS from the DLC3.



Hide 9.INSPECT COMPRESSION


b.

Remove the relay block cover.


c.
A276923E01
0.131,0.11 0.312,0.276 0.181,0.166 10 *1 1.424,2.441 0.929,2.441 false 0.372,2.356 0.857,2.522 0.486,0.166 10 F/PMP

Remove the F/PMP fuse.

Text in Illustration
*1 Engine Room Relay Block


d.

Warm up and stop the engine.



f.
A276029

Insert a compression gauge into the spark plug hole.


g.

Install the injector driver.

Click hereEngine / Hybrid System>FA20 FUEL>INJECTOR DRIVER>INSTALLATION


h.

Inspect the cylinder compression pressure.

i.

While cranking the engine, measure the compression pressure.

HINT:

Always use a fully charged battery to obtain an engine speed of 250 rpm or more.


NOTICE:

The measurement must be performed as quickly as possible.


Standard compression pressure:

1750 kPa (17.8 kgf/cm2, 254 psi) or higher


Minimum pressure:

1150 kPa (11.7 kgf/cm2, 167 psi)


Difference between each cylinder:

200 kPa (2.0 kgf/cm2, 29 psi) or less


HINT:

If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect the compression again. Then perform the 2 steps above for the cylinders with low compression.


·

If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.

·

If the pressure stays low, a valve may be stuck or seated improperly, or there may be leakage from the gasket.




i.

Remove the injector driver.

Click hereEngine / Hybrid System>FA20 FUEL>INJECTOR DRIVER>REMOVAL



k.

Reinstall the F/PMP fuse.


l.

Install the relay block cover.



Hide 10.INSPECT CO/HC

HINT:

This check is for determining whether or not the idle CO/HC complies with regulations.


a.

Start the engine.


b.

Maintain the engine speed at 2500 rpm for approximately 180 seconds.


c.

Insert a CO/HC meter testing probe at least 40 cm (1.31 ft) into the tailpipe during idling.


d.

Immediately check the CO/HC concentration at idle and/or 2500 rpm.

HINT:
·

When performing the 2 mode (2500 rpm and idle) test, follow the measurement order prescribed by the applicable local regulations.

·

If the CO/HC concentration does not comply with regulations, troubleshoot in the order given below.




ii.

Refer to the table below for the possible cause, and then inspect and correct the applicable causes if necessary.

CO HC Symptom Causes
Normal High Rough idle
1.

Faulty ignition:

-

Incorrect timing

-

Plugs are contaminated or shorted, or plug gaps are incorrect


2.

Incorrect valve clearance

3.

Leaky intake and exhaust valves

4.

Leaky cylinders


Low High Rough idle
(Fluctuating HC reading)
1.

Vacuum leaks:

-

Ventilation hoses

-

Intake manifold

-

Throttle body


2.

Lean mixture causing misfire


High High Rough idle
(Black smoke from exhaust)
1.

Restricted air filter

2.

Plugged PCV valve

3.

Faulty EFI system:

-

Faulty pressure regulator

-

Defective engine coolant temperature sensor

-

Faulty mass air flow meter

-

Faulty ECM

-

Faulty injectors

-

Faulty throttle position sensor