Home › Engine / Hybrid System › M20A-FXS (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2020.08
RM32K0E _51 Engine / Hybrid System _083976 M20A-FXS ENGINE MECHANICAL _0404777 ENGINE ASSEMBLY A

M20A-FXS ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 2.REMOVE ENGINE FROM ENGINE STAND

a.

Remove the engine assembly from the engine stand.


Hide 19315 3.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 31270 5.INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY

Hide 88370 6.INSTALL COMPRESSOR WITH MOTOR ASSEMBLY

Hide 82121 8.INSTALL ENGINE WIRE

a.

Connect all the connectors and clamps, and install the engine wire to the engine assembly with transaxle.


b.
A434066

Install the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.
A434065

Install the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.
A434064

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


e.
A426083

Install the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 23819 10.INSTALL NO. 2 FUEL VAPOR FEED PIPE

a.

Install the No. 2 fuel vapor feed pipe to the fuel hose brackets with the bolt and nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11363A 11.INSTALL FLYWHEEL HOUSING SIDE COVER

a.
A431858

Install the flywheel housing side cover to the cylinder block sub-assembly.


Hide 12305 13.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A434063C01
0.104,2.208 0.688,2.396 0.583,0.188 10 true 1 (*a), 3 2.646,1.677 2.813,1.865 0.167,0.188 10 true 2 1.646,0.531 1.813,0.719 0.167,0.188 10 true 4
*a Temporarily Tighten


Temporarily install the engine mounting insulator sub-assembly RH to the vehicle.


b.

Install the 2 bolts and nut in the order shown in the illustration.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


c.

Connect the air conditioner tube and accessory assembly with the bolt and nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


d.

Install the No. 2 earth wire to the engine mounting insulator sub-assembly RH and vehicle with the 2 bolts.

Torque:
10.5 N*m (107 kgf*cm, 8 ft.*lbf)


Hide 12372A 14.INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A434061C04
0.24,0.917 0.844,1.135 0.604,0.219 10 true 1 (*a), 7 3.042,1.896 3.24,2.083 0.198,0.188 10 true 3 0.531,1.906 0.708,2.083 0.177,0.177 10 true 4 2.208,0.073 2.458,0.271 0.25,0.198 10 true 5 2.688,0.979 3.292,1.198 0.604,0.219 10 true 2 (*a), 6
*a Temporarily Tighten


Temporarily install the engine mounting insulator LH to the vehicle.


b.

Install the 4 bolts and nut in the order shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 16.INSTALL EMISSION CONTROL VALVE BRACKET

a.

Install the emission control valve bracket to the cylinder head sub-assembly with the bolt.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 18.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

a.

Using height adjustment attachments and plate lift attachments to keep the engine assembly with transaxle and front suspension crossmember sub-assembly level, set an engine lifter underneath the engine assembly with transaxle and front suspension crossmember sub-assembly.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle horizontal.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.




b.

Operate the engine lifter and install the engine assembly with transaxle to the vehicle.

CAUTION:

Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.




c.

Connect the front suspension crossmember sub-assembly to the vehicle with the 6 bolts.

Torque:
141 N*m (1438 kgf*cm, 104 ft.*lbf)


d.
C406256

Fully tighten the front suspension crossmember sub-assembly to the No. 2 engine moving control rod with the bolt.

Torque:
170 N*m (1734 kgf*cm, 125 ft.*lbf)


e.
A397417C01
1.563,1.375 1.917,0.583 1.917,0.583 2.083,0.583 false 2.167,0.5 2.479,0.698 0.313,0.198 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads of bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



f.

Install the No. 2 engine mounting stay LH with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


g.

Install the engine mounting insulator LH to the hybrid vehicle transaxle assembly with the 3 bolts and nut.

Torque:
Bolt : 70 N*m (714 kgf*cm, 52 ft.*lbf)
Nut : 20 N*m (204 kgf*cm, 15 ft.*lbf)


h.

Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 2 bolts and nut.

Torque:
Bolt : 72 N*m (734 kgf*cm, 53 ft.*lbf)
Nut : 41 N*m (418 kgf*cm, 30 ft.*lbf)


Hide 51108A 19.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

Hide 51107A 20.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 17410 22.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 45025D 23.CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 45260 24.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 25.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 88704 26.INSTALL SUCTION HOSE SUB-ASSEMBLY

Hide 88703 27.INSTALL DISCHARGE HOSE SUB-ASSEMBLY

Hide 16267 28.CONNECT NO. 3 WATER BY-PASS HOSE

a.

Engage the clamp to install the No. 3 water by-pass hose.


Hide 16283B 29.CONNECT WATER BY-PASS HOSE

a.

Connect the water by-pass hose to the No. 3 water by-pass pipe and slide the hose clip to secure it.


Hide 23901 30.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly to the fuel pump assembly.

Click hereEngine / Hybrid System>M20A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


b.

Engage the clamp to connect the fuel tube sub-assembly.


Hide 87246 31.CONNECT OUTLET HEATER WATER HOSE

a.
A444908C01
1,1.219 1.448,1.219 false 2.052,1.073 2.5,1.073 false 1.063,1.5 1.51,1.5 false 2.104,1.344 2.552,1.344 false 0.802,1.115 1.115,1.313 0.313,0.198 10 false *a 2.542,0.958 2.854,1.156 0.313,0.198 10 false *a 2.604,1.26 2.917,1.458 0.313,0.198 10 false *b 0.875,1.406 1.188,1.604 0.313,0.198 10 false *b
*a Protrusion
*b Cutout


Align the protrusions of the outlet heater water hose connector with the cutouts in the water hose sub-assembly and push them together until the outlet heater water hose connector makes a "click" sound.


b.
A451414C01
1.906,0.313 1.625,0.625 true 1.896,0.229 2.104,0.427 0.208,0.198 10 true *a
*a Retainer
V100135

Push
V100136

Push in


Push in the retainer.


c.

Check that the water hose sub-assembly and outlet heater water hose connector are securely connected by pulling on them.


Hide 87245 32.CONNECT INLET HEATER WATER HOSE

a.
A403463C02
1.052,1.156 1.573,1.156 false 0.99,0.365 1.219,0.365 1.219,0.365 1.521,0.792 false 0.875,1.063 1.188,1.219 0.313,0.156 10 false *a 0.823,0.281 1.135,0.438 0.313,0.156 10 false *b
*a Protrusion
*b Cutout


Align the protrusion of the water hose sub-assembly with the cutout in the inlet heater water hose connector and push them together until the inlet heater water hose makes a "click" sound.


b.
A451415C01
2.583,0.677 2.219,0.875 true 2.594,0.563 2.802,0.76 0.208,0.198 10 true *a
*a Retainer
V100135

Push
V100136

Push in


Push in the retainer.


c.

Check that the water hose sub-assembly and inlet heater water hose connector are securely connected by pulling on them.


Hide 23825 33.INSTALL FUEL DELIVERY GUARD

a.

Install the fuel delivery guard to the engine mounting bracket RH with the bolt.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 23818 34.INSTALL FUEL VAPOR FEED PIPE

a.

Install the fuel vapor feed pipe to the fuel delivery guard with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Engage the clamp to connect the No. 1 fuel vapor feed hose.


c.

Engage the clamp to install the engine wire with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 25860 35.INSTALL PURGE VALVE (PURGE VSV)

Hide 23829A 36.INSTALL NO. 1 FUEL VAPOR FEED HOSE

a.

Align the No. 1 fuel vapor feed hose connector with the No. 2 fuel vapor feed pipe, and push them together until the No. 1 fuel vapor feed hose connector makes a "click" sound.

NOTICE:
·

Check that there is no foreign matter on the connecting parts.

·

After connecting the No. 1 fuel vapor feed hose connector, check that the No. 2 fuel vapor feed pipe and No. 1 fuel vapor feed hose connector are securely connected by pulling on them.




Hide G922F 37.CONNECT OUTLET NO. 1 HYBRID WATER PUMP HOSE

a.

Connect the outlet No. 1 hybrid water pump hose to the motor cooling cooler and slide the clip to secure it.


Hide G922H 38.CONNECT INLET HYBRID RADIATOR HOSE

a.

Connect the inlet hybrid radiator hose to the motor cooling cooler and slide the clip to secure it.


Hide 16572D 39.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the water inlet sub-assembly and slide the clip to secure it.


b.

Engage the 3 clamps to connect the No. 1 inverter cooling hose assembly and inlet hybrid water pump hose to the fan shroud assembly.


Hide 16571C 40.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the No. 1 radiator hose to the water outlet and slide the clip to secure it.


b.

Engage the clamp to connect the No. 1 radiator hose.


Hide 33820B 41.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.


b.

Install the transmission control cable assembly to the control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide G92A0A 42.INSTALL INVERTER RESERVE TANK ASSEMBLY

a.

Connect the inlet hybrid water pump hose to the inverter reserve tank assembly and slide the clip to secure it.


b.

Connect the No. 1 inverter cooling hose assembly to the inverter reserve tank assembly and slide the clip to secure it.


c.

Install the inverter reserve tank assembly with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 44.CONNECT ENGINE WIRE

a.

Engage the 3 clamps to connect the engine wire to the vehicle.


b.

Connect the engine wire to the vehicle with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Engage the 2 claws to connect the engine wire to the engine room relay block.


d.

Install the nut.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


e.

Engage the 2 claws to connect the engine wire to the engine room relay block.


f.

Connect the 3 connectors to the engine room relay block.


Hide 82662A 45.INSTALL NO. 1 RELAY BLOCK COVER

a.

Engage the 2 guides and claw to install the No. 1 relay block cover to the engine room relay block.


Hide 17701 47.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.

Install the air cleaner case sub-assembly with the 3 bolts.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 17801 48.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 49.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17751 50.INSTALL NO. 1 AIR CLEANER INLET

a.

Install the No. 1 air cleaner inlet to the upper radiator support sub-assembly and air cleaner case sub-assembly with the 4 bolts.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 53.ADD ENGINE COOLANT (for Engine)

Hide 54.ADD HYBRID TRANSAXLE FLUID

Hide 55.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 60.INSPECT FOR ENGINE OIL LEAK

Hide 62.INSPECT FOR COOLANT LEAK (for Engine)

Hide 67.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR TANK

Hide 51444A 68.INSTALL REAR ENGINE UNDER COVER LH

a.

Install the rear engine under cover LH to the vehicle with the 6 clips.


Hide 51443C 69.INSTALL REAR ENGINE UNDER COVER RH

a.

Install the rear engine under cover RH to the vehicle with the 6 clips.


Hide 51410 70.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

a.
A431384C05
0.74,0.01 0.927,0.177 0.188,0.167 10 true *a 1.25,0.01 1.448,0.177 0.198,0.167 10 true *a 2.01,0 2.208,0.167 0.198,0.167 10 true *a 2.531,0 2.729,0.167 0.198,0.167 10 true *a
*a Bolt


Install the No. 1 engine under cover assembly to the vehicle with the 4 bolts, 4 screws and 4 clips.

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 71.INSTALL FRONT WHEELS

Hide 72. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 73.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT