Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM › 2011.10–2013.07
RM19V0EQ _51 Engine / Hybrid System _014573 2AR-FE ENGINE CONTROL _0075838 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P1603  Engine Stall History  P1605  Rough Idling  


DESCRIPTION

P1603 (for Automatic Transaxle models)

After starting the engine, this DTC is stored when the engine stops without the ignition switch being operated.

Using the intelligent tester, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

It is necessary to check if the vehicle has run out of fuel in the past before performing troubleshooting, as this DTC is also stored when the engine stalls due to running out of fuel.


P1605

This DTC is stored if the engine speed drops below the set speed.

Using the intelligent tester, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

It is necessary to check if the vehicle has run out of fuel in the past before performing troubleshooting, as this DTC is also stored when idling is unstable due to running out of fuel.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1603 Engine Stall History After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the engine, with the engine running, the engine stops (the engine speed drops to 200 rpm or less) without the ignition switch being operated for 0.5 seconds or more (1 trip detection logic).
·

Air leak in intake system

·

Purge VSV

·

Brake booster hose not connected properly

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Wire harness or connector

·

Air fuel ratio sensor (sensor 1)

·

Power supply circuit (purge VSV, fuel injector assembly, ignition coil assembly)

·

Fuel pump

·

Fuel pump control system

·

Fuel line (fuel filter, pipes and hoses)

·

Throttle with motor body assembly

·

Camshaft timing oil control valve assembly

·

Air conditioning system

·

Power steering system

·

Electrical load signal system

·

A/T system

·

Park/Neutral position switch assembly

·

Thermostat

·

ECM


Does not come on (A/T models only) DTC stored (A/T models only)
P1605 Rough Idling After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to 400 rpm or less (1 trip detection logic).
·

Air leak in intake system

·

Purge VSV

·

Brake booster hose not connected properly

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Wire harness or connector

·

Air fuel ratio sensor (sensor 1)

·

Power supply circuit (purge VSV, fuel injector assembly, ignition coil assembly)

·

Fuel pump

·

Fuel pump control system

·

Fuel line (fuel filter, pipes and hoses)

·

Throttle with motor body assembly

·

Camshaft timing oil control valve assembly

·

Knock control sensor

·

Ignition coil assembly (No. 1 to No. 4 cylinder)

·

Fuel injector assembly

·

Spark plug(s)

·

Air conditioning system

·

Power steering system

·

Electrical load signal system

·

A/T system*1

·

Park/Neutral position switch assembly*1

·

ECM


Does not come on DTC stored

*1: for Automatic Transaxle models.

Reference waveforms showing a normal cold engine start


A255812


Reference waveforms showing a normal warm engine start


A255813


Reference values when there is an air leak in the intake system during rough idling


Freeze Frame Data P1605 Rough Idling
Parameter -3 -2 -1 0 1 Unit
Engine Speed 533 516 612 420 416 rpm
Calculate Load 39.2 40.0 40.0 41.1 42.3 %
Vehicle Load 24.7 27.0 16.8 40.7 35.2 %
MAF 3.56 3.75 2.81 4.59 3.93 gm/sec
Atmosphere Pressure 14.5 14.5 14.5 14.5 14.5 psi (gauge)
Coolant Temp 189 189 189 189 189 F
Intake Air 109 109 109 109 109 F
Battery Voltage 13.105 13.144 13.359 12.949 12.910 V
Throttle Sensor Volt % 17.2 15.6 15.2 16.8 16.4 %
Throttle Sensor #2 Volt % 49.4 47.4 47.0 49.0 48.6 %
Throttle Sensor Position 0.0 0.0 0.0 0.0 0.0 %
Throttle Motor DUTY 17.6 15.2 15.2 15.2 16.8 %
Injector (Port) 4160 4194 4056 4979 5042 μs
Injection Volume (Cylinder 1) 0.175 0.175 0.228 0.228 0.228 ml
Fuel Pump/Speed Status ON ON ON ON ON
EVAP (Purge) VSV 0.0 0.0 0.0 0.0 0.0 %
Evap Purge Flow 0.0 0.0 0.0 0.0 0.0 %
Purge Density Learn Value 0.000 0.000 0.000 0.000 0.000
EVAP purge VSV OFF OFF OFF OFF OFF
Target Air-Fuel Ratio 0.999 0.999 0.999 0.999 0.999
AF Lambda B1S1 1.232 1.232 1.232 1.232 1.232
AFS Voltage B1S1 4.996 4.996 4.996 4.996 4.996 V
O2S B1S2 0.000 0.000 0.000 0.000 0.000 V
Short FT #1 18.750 18.750 18.750 18.750 18.750 %
Long FT #1 3.906 3.906 3.906 3.906 3.906 %
Total FT #1 0.000 0.000 0.000 0.000 0.000
Fuel System Status #1 CL CL CL CL CL
IGN Advance 15.0 14.0 14.5 15.0 0.5 deg
Knock Feedback Value -3.0 -3.0 -3.0 -3.0 -3.0 °CA
Knock Correct Learn Value 19.0 19.0 19.0 19.0 19.0 °CA
VVT Control Status #1 OFF OFF OFF OFF OFF
Starter Signal Close Close Close Close Close


WIRING DIAGRAM

Refer to DTC P0031 for the air fuel ratio sensor circuit.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0031

Refer to DTC P0351 for the ignition coil assembly circuit.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0351

Refer to DTC P0443 for the purge VSV circuit.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0443

Refer to Fuel Pump Control Circuit.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>Fuel Pump Control Circuit

Refer to Fuel Injector Circuit.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>Fuel Injector Circuit

CAUTION / NOTICE / HINT

HINT:
·

In contrast to normal malfunction diagnosis for components, circuits and systems, DTCs P1603 and P1605 are used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine stall.

As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.

·

If any other DTCs are output, perform troubleshooting for those DTCs first.

·

Use any information from the customer problem analysis about the condition of the vehicle at the time when the problem occurred (how the engine stopped, conditions when the engine was restarted, etc.) as a reference.

Symptom Suspected Area
Engine vibration occurs and engine stops Air fuel ratio abnormal
Engine stops with no engine vibration Ignition system, injection stoppage, high load from external parts
Engine can be started with accelerator pedal depressed Insufficient air volume
Rough idling after engine started Air fuel ratio abnormal, abnormal combustion

·

Read freeze frame data using the intelligent tester. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

·

When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA

·

When DTC P1603 (Engine Stall History) is stored, DTC P1605 (Rough Idling) is also stored. When confirming freeze frame data, check DTC P1605. (The ECM stores DTC P1605 first. Therefore, the 5 sets of freeze frame data can be confirmed through DTC P1605, enabling the technician to obtain more information.)

·

When confirming freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.

·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.

·

Inspections take into account the fact that the malfunction may not have reoccurred and place emphasis on checking the vehicle conditions present at the time when the malfunction occurred.

·

When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.



Inspection flow:

Using freeze frame data, narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred.


P1603:

A224366E02
0.219,0.775 1.114,1.107 0.895,0.332 10 While idling or while driving? 1.824,0.778 3.156,1.479 1.332,0.7 10 Did the engine speed decrease slowly or rapidly when engine stall occurred? 0.189,0.599 0.373,0.783 0.184,0.184 10 1: 1.824,0.599 2.008,0.783 0.184,0.184 10 2: 3.925,0.778 4.961,1.296 1.036,0.517 10 Was the air fuel ratio abnormal or normal? 3.925,0.599 4.109,0.783 0.184,0.184 10 3: 5.961,0.75 6.905,0.916 0.943,0.166 10 Intake air leak 5.781,1.758 7.032,1.923 1.25,0.166 10 Sensor malfunction 1.242,5.833 2.492,5.998 1.25,0.166 10 Sensor malfunction 5.748,2.763 7.061,2.928 1.314,0.166 10 Fuel supply problem 1.214,7.822 2.528,7.988 1.314,0.166 10 Fuel supply problem 6.036,3.459 6.746,3.81 0.71,0.351 10 Air volume insufficient 5.953,4.47 6.878,4.803 0.925,0.332 10 Ignition timing incorrect 3.41,4.481 4.492,4.822 1.082,0.341 10 Injection and ignition stoppage 1.337,6.554 2.419,6.896 1.082,0.341 10 Injection and ignition stoppage 3.497,5.48 4.394,5.822 0.897,0.341 10 Load from external parts 1.31,0.134 1.698,0.299 0.388,0.166 10 Idling 0.096,2.544 0.557,2.709 0.462,0.166 10 Driving 2.972,0.134 4.157,0.299 1.184,0.166 10 Decreased Slowly 1.16,2.544 2.4,2.746 1.24,0.203 10 Decreased Rapidly 5.027,0.134 5.693,0.318 0.666,0.184 10 Abnormal 3.832,2.544 4.331,2.709 0.499,0.166 10 Normal

1:
·

If the engine stalled when the intake air volume was low (during idling or deceleration), there may be a decrease in torque due to an incorrect air fuel ratio, etc.

·

If the engine stalled when the intake air volume was high (during driving or acceleration), there may be a major malfunction such as continuous misfire due to ignition stoppage, fuel injection stoppage, etc. and the torque drops to zero.


2:
·

If the engine speed decreased slowly, there may have been a decrease in torque due to an air fuel ratio that was incorrect (by approximately 20 to 30%), etc.

·

If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.


3:
·

If the air fuel ratio was abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.

·

If the air fuel ratio was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.


P1603 inspection flow: Narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred (freeze frame data).

Vehicle State Engine Speed Suspected Area Primary Parts to Inspect Procedure
Idling or decelerating Slowly decreases and engine stalls Air fuel ratio abnormal Air suction
·

Intake system connections

·

Purge VSV system

·

Brake booster


3 to 6
Sensor malfunction (value from sensor too lean)
·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Air fuel ratio sensor system


7 to 16
Sensor malfunction (value from sensor too rich) 22 to 26, 29 to 31, 33, 34
Fuel supply problem
·

Fuel pump control system

·

Purge VSV system

·

Fuel line

·

ECM


17 to 21, 27, 28, 32
Intake air volume insufficient ISC flow rate
·

Throttle with motor body assembly (ISC valve)


35 to 37
Excessive valve overlap
·

Camshaft timing oil control valve assembly


38, 39
Ignition timing incorrect Does not operate as expected
·

Engine coolant temperature sensor

·

Knock control sensor

·

Mass air flow meter sub-assembly


40 to 42
Rapidly decreases and engine stalls Ignition and injection stops (electrical system malfunction) Power temporarily cut
·

Power supply circuit (fuel injector assembly, ignition coil assembly)


43, 44
External part malfunctioning Increase in load
·

Air conditioning system

·

Electrical load signal system

·

Power steering system

·

A/T system

·

Park/Neutral position switch assembly


47 to 51
Accelerating - Crankshaft position sensor, camshaft position sensor malfunction Power temporarily cut
·

Check DTCs


1
Mass air flow meter sub-assembly Foreign matter adhesion
·

Mass air flow meter sub-assembly


53
Fuel supply problem Fuel leak, clog
·

Fuel pump control system

·

Fuel line


56 to 58
Ignition and injection stops (electrical system malfunction) Power temporarily cut
·

Power supply circuit (fuel injector assembly, ignition coil assembly)


54, 55

P1605:

A224367E02
0.498,0.514 0.668,0.689 0.17,0.175 10 1: 0.498,0.71 1.64,1.214 1.142,0.503 10 Did the engine speed decrease slowly or rapidly? 2.819,0.514 2.989,0.689 0.17,0.175 10 2: 2.819,0.71 3.962,1.214 1.142,0.503 10 Was the air fuel ratio abnormal or normal? 5.69,0.715 6.634,0.881 0.943,0.166 10 Intake air leak 5.549,1.727 6.789,1.892 1.24,0.166 10 Sensor malfunction 5.522,2.722 6.799,2.925 1.277,0.203 10 Fuel supply problem 4.034,2.065 4.743,2.385 0.709,0.32 10 Air volume insufficient 3.925,3.05 4.85,3.383 0.925,0.332 10 Ignition timing incorrect 1.582,2.706 2.673,3.057 1.091,0.351 10 Injection and ignition stoppage 1.662,3.707 2.587,4.058 0.925,0.351 10 Load from external parts 1.908,0.876 2.629,1.226 0.721,0.351 10 Decreased Slowly 0.264,1.847 0.985,2.198 0.721,0.351 10 Decreased Rapidly 4.299,0.894 4.946,1.06 0.647,0.166 10 Abnormal 2.776,1.847 3.294,2.012 0.517,0.166 10 Normal

1:
·

If the engine speed decreased slowly, there may have been a decrease in torque due to an air fuel ratio that was incorrect (by approximately 20 to 30%), etc.

·

If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.


2:
·

If the air fuel ratio was abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.

·

If the air fuel ratio was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.


P1605 inspection flow: Narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred (freeze frame data).

Engine Speed Suspected Area Primary Parts to Inspect Procedure
Slowly decreases Air fuel ratio abnormal Air suction
·

Intake system connections

·

Purge VSV system

·

Brake booster assembly


3 to 6
Sensor malfunction (value from sensor too lean)
·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Air fuel ratio sensor system


7 to 16
Sensor malfunction (value from sensor too rich) 17 to 21, 27, 28, 32
Fuel supply problem
·

Fuel pump control system

·

Purge VSV system

·

Fuel line

·

ECM


19 to 23, 27, 28, 32
Intake air volume insufficient ISC flow rate
·

Throttle with motor body assembly (ISC valve)


35 to 37
Ignition timing incorrect Does not operate as expected
·

Knock control sensor

·

Engine coolant temperature sensor

·

Mass air flow meter sub-assembly


40 to 42
Rapidly decreases Ignition and injection stops (electrical system malfunction) Power temporarily cut
·

Power supply circuit (fuel injector assembly, ignition coil assembly)


43, 44
External part malfunctioning Increase in load
·

Air conditioning system

·

Power steering system

·

A/T system*1

·

Park/Neutral position switch assembly*1


47 to 51

*1: for Automatic Transaxle models.

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1603 AND/OR P1605)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P1603 and/or P1605 is output A
DTC P1603 or P1605 and other DTCs are output B



A

2.READ FREEZE FRAME DATA

B

2.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA


Result:
Problem Symptom Freeze Frame Data Item Suspected Area Proceed to
Closed Throttle Position SW Engine Speed Total of Short FT #1 and Long FT #1
When idling or decelerating, engine speed slowly decreases (and engine stalls) All 5 sets of freeze frame data are ON Decreases slowly*1 All 5 sets of freeze frame data are 15% or higher*2
·

Air suction

·

Sensor malfunction (value from sensor too lean)

·

Fuel supply problem


A
At least 1 of the 5 sets of freeze frame data is -15% or less*3 Sensor malfunction (value from sensor too rich) B
All 5 sets of freeze frame data are between -15% and 15%
·

Intake air volume insufficient

·

Ignition timing incorrect


C
When idling or decelerating, engine speed rapidly decreases (and engine stalls) Decreases rapidly*1 -
·

Injection stoppage, ignition stoppage

·

Load from external parts


D
When accelerating or driving at constant speed, engine stalls*4 At least one is OFF - -
·

Sensor malfunction

·

Injection stoppage, ignition stoppage

·

Fuel supply problem


E


A215381E12
0.072,0.032 2.178,0.197 2.105,0.166 10 Rapid Decrease in Engine Speed 2.333,0.377 2.702,0.561 0.369,0.184 10 (rpm) 2.389,0.723 2.665,0.87 0.277,0.147 10 800 2.389,0.928 2.665,1.075 0.277,0.147 10 600 2.389,1.126 2.665,1.273 0.277,0.147 10 400 2.389,1.331 2.665,1.478 0.277,0.147 10 200 2.548,1.529 2.689,1.676 0.142,0.147 10 0 3.038,1.642 3.236,1.798 0.198,0.156 10 #1 3.472,1.642 3.67,1.798 0.198,0.156 10 #2 3.935,1.642 4.132,1.798 0.198,0.156 10 #3 4.153,1.642 4.351,1.798 0.198,0.156 10 #4 4.377,1.642 4.575,1.798 0.198,0.156 10 #5 4.985,1.105 6.058,1.261 1.073,0.156 10 400 rpm or more 1.216,1.019 2.123,1.203 0.906,0.184 10 Engine Speed 2.702,1.944 4.816,2.128 2.115,0.184 10 Freeze Frame Data Storage Point

HINT:
·

*1: A rapid decrease in engine speed may be caused by an electrical fault in the shared wiring of all or a number of cylinders, an increase in load from external parts, etc. The engine speed is considered to have decreased rapidly if either of the following conditions applies.

Otherwise, the engine speed is considered to have decreased slowly.


1.

In the freeze frame data, the decrease in engine speed from #3 to #5 is 400 rpm or higher.

2.

In the freeze frame data, the engine speed at #5 is 120 rpm or less.


·

If the vehicle speed is 15 km/h (9 mph) or less and the difference between Engine Speed and SPD (NT) is 100 rpm or less, inspect the automatic transaxle. (Depending on the rate of vehicle deceleration, the engine speed may have decreased due to the A/T lock-up release being late.) (for Automatic Transaxle models)

·

*2: When a DTC is stored, feedback compensation increases because the air fuel ratio is determined to be lean.

·

*3: When a DTC is stored, feedback compensation decreases because the air fuel ratio is determined to be rich.

·

*4: This item should be checked when DTC P1603 is output and is not necessary to check when only P1605 is output.




A

3.CHECK INTAKE SYSTEM

B

22.READ FREEZE FRAME DATA

C

35.READ FREEZE FRAME DATA

D

43.CHECK TERMINAL VOLTAGE (#10, #20, #30 AND/OR #40)

E

52.READ FREEZE FRAME DATA
3.CHECK INTAKE SYSTEM
a.

Check for air leaks in the intake system (vacuum hose disconnection, cracks, damaged gaskets, etc.).

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.

·

If Short FT #1 and Long FT #1 are largely different from the normal values when idling (the intake air volume is small) and almost the same as the normal values when racing the engine (the intake air volume is high), air leaks may be present.



OK:

There is no air leaks.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

4.CHECK PURGE VSV

NG

REPAIR OR REPLACE INTAKE SYSTEM

4.CHECK PURGE VSV
a.
A255086C02
1.708,1.333 1.938,0.229 1.938,0.229 2.156,0.229 false 0.771,2.177 0.771,3.177 0.771,3.177 0.958,3.177 false 1.01,1.49 1.125,0.229 1.125,0.229 1.323,0.229 false 1.344,0.135 1.615,0.333 0.271,0.198 10 *2 2.177,0.135 2.417,0.323 0.24,0.188 10 *3 1,3.083 1.177,3.281 0.177,0.198 10 *1
*1 Fuel Vapor Feed Hose (to Canister)
*2 Connector
*3 Purge VSV


Disconnect the fuel vapor feed hose (on the canister side) of the purge VSV.


b.

Start the engine.


c.

Idle the engine.


d.

Disconnect the connector of the purge VSV.


e.

Check if air flows through the purge VSV.

OK:

Air does not flow.


HINT:

When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR



Result:
Proceed to
OK
NG



OK

5.READ FREEZE FRAME DATA

NG

5.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Stop Light Switch At least 1 of the 5 sets of freeze frame data is ON Air suction from brake booster assembly A
All 5 sets of freeze frame data are OFF - B



A

6.READ VALUE USING INTELLIGENT TESTER (SHORT FT #1)

B

7.READ FREEZE FRAME DATA
6.READ VALUE USING INTELLIGENT TESTER (SHORT FT #1)
a.
A217928E01
0.214,0.569 0.925,0.739 0.711,0.170 10 Depressed 0.093,0.053 0.902,0.209 0.809,0.156 10 Brake Pedal 0.308,1.092 0.936,1.248 0.628,0.156 10 Released 0.114,1.834 0.881,1.989 0.767,0.156 10 Short FT #1 2.508,2.227 3.261,2.564 0.753,0.336 10 Change is 10% or less

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



d.

Idle the engine.


e.

Using the tester, read [Short FT #1] of the Data List while depressing the brake pedal.

Standard:

Short FT #1 changes by 10% or less.


HINT:
·

Even if the results are normal, the brake booster assembly may have been malfunctioning. Continue this inspection procedure until step 32, and if there are no problems with other parts, replace the brake booster assembly (refer to step 59).

·

When air leaks from the brake booster assembly is present, the feedback compensation increases because the air fuel ratio becomes lean.

·

It is also possible to perform the airtightness inspection to check the brake booster assembly.




Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

7.READ FREEZE FRAME DATA

B

REPLACE BRAKE BOOSTER ASSEMBLY

C

REPLACE BRAKE BOOSTER ASSEMBLY

7.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Calculate Load Below 90% of the current value of the vehicle*1 Mass air flow meter sub-assembly A
AFS Voltage B1S1 3.3 V or higher*2
·

Air fuel ratio sensor

·

Wire harness or connector

·

Actual air fuel ratio abnormal


B
Both freeze frame data items listed above Values are other than above - C


HINT:
·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N (neutral)) and compare these data with the freeze frame data.

·

*1: If the mass air flow meter sub-assembly is malfunctioning, the freeze frame data will show a low engine load value.

·

*2: If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air fuel ratio is lean, the actual air fuel ratio will become rich and the engine may stall.




A

8.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY

B

9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

C

12.READ FREEZE FRAME DATA
8.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
a.

Remove the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL


b.

Check for foreign matter in the air flow passage of the mass air flow meter sub-assembly.


Result:
Result Proceed to
Visible foreign matter is present A
Visible foreign matter is not present B


HINT:
·

Even if the results are normal, the mass air flow meter sub-assembly may have been malfunctioning. Continue this inspection procedure until step 32, and if there are no problems with other parts, replace the mass air flow meter sub-assembly (refer to step 59).

·

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




A

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

B

12.READ FREEZE FRAME DATA
9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.
A280723E12
1.208,0.604 1.75,0.833 0.542,0.229 10 12.5% 1.167,0.938 1.667,1.156 0.5,0.219 10 -12.5% 0.615,2.208 1.75,2.417 1.135,0.208 10 Higher than 3.4 V 0.531,3.781 1.74,3.99 1.208,0.208 10 Higher than 0.55 V 0.938,2.583 1.719,2.792 0.781,0.208 10 Below 3.1 V 0.938,4.146 1.75,4.365 0.813,0.219 10 Below 0.4 V 1.031,0.25 2.115,0.458 1.083,0.208 10 Injection Volume 0.635,1.771 3.031,1.99 2.396,0.219 10 Air Fuel Ratio Sensor Output Voltage 0.698,3.313 3.115,3.531 2.417,0.219 10 Heated Oxygen Sensor Output Voltage

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
AFS Voltage B1S1
O2S B1S2
50004 234 2 35,44

f.

Change the fuel injection volume using the tester, and monitor the voltage output of the air fuel ratio and heated oxygen sensors displayed on the tester.

Standard:
Tester Display Specified Condition
Control the Injection Volume for A/F Sensor (12.5%) Air fuel ratio sensor output voltage is below 3.1 V
Control the Injection Volume for A/F Sensor (-12.5%) Air fuel ratio sensor output voltage is higher than 3.4 V



Result:
Result Proceed to
Abnormal A
Normal B


HINT:
·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

Even if the results are normal, the air fuel ratio sensor may have been malfunctioning. Continue this inspection procedure until step 32, and if there are no problems with other parts, replace the air fuel ratio sensor (refer to step 59).




A

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)

B

12.READ FREEZE FRAME DATA
10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)
a.

Check the harnesses and connectors, referring to DTC P0031 inspection procedure.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0031

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

REPAIR POWER SOURCE CIRCUIT (AIR FUEL RATIO SENSOR POWER SOURCE)

11.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Check the harnesses and connectors, referring to DTC P2237 inspection procedure.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P2237

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Proceed to
Initial Engine Coolant Temp, Initial Intake Air Temp Difference in temperature between each item is below 10°C (18°F)*1 A
Difference in temperature between each item is 10°C (18°F) or higher*2 B


HINT:
·

*1: A long time had elapsed after stopping the engine.

·

*2: A long time had not elapsed after stopping the engine.




A

13.READ FREEZE FRAME DATA

B

15.READ FREEZE FRAME DATA
13.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA

A217929E28
0.229,0.854 3.083,1.521 2.854,0.667 10 Engine Coolant Temperature Increase after Engine Start (Engine Coolant Temperature - Engine Coolant Temperature at Engine Start) 3.427,0.042 3.719,0.24 0.292,0.198 10 (°C) 5.604,2.115 6.219,2.281 0.615,0.167 10 (Minutes) 5.146,1.771 5.302,1.927 0.156,0.156 10 A 4.938,0.844 5.229,1.104 0.292,0.26 10 C 3.875,0.552 4.031,0.708 0.156,0.156 10 B 3.563,2.385 5.573,2.542 2.01,0.156 10 Time Elapsed after Engine Start


Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Initial Engine Coolant Temp, Coolant Temp, Engine Run Time Range A
·

Engine coolant temperature sensor

·

Thermostat


A
Range B Engine coolant temperature sensor B
Range C - C


HINT:

This step is not directly related to engine stall.



A

14.INSPECT THERMOSTAT

B

16.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

C

17.READ FREEZE FRAME DATA
14.INSPECT THERMOSTAT

Result:
Result Proceed to
Abnormal A
Normal B


HINT:

This step is not directly related to engine stall.



A

B

16.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
15.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Coolant Temp 120°C (248°F) or higher Engine coolant temperature sensor A
Engine coolant temperature is lower than outside temperature* by 15°C (27°F) or higher Engine coolant temperature sensor
Both freeze frame data items listed above Values are other than above - B


HINT:

*: Use an actual outside temperature estimated from the Initial Intake Air, Ambient Temp for A/C, and (if possible) the weather when the DTC was detected.



A

16.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

17.READ FREEZE FRAME DATA
16.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Result Proceed to
Abnormal A
Normal B


HINT:
·

Even if the results are normal, the engine coolant temperature sensor may have been malfunctioning. Continue this inspection procedure until step 32, and if there are no problems with other parts, replace the engine coolant temperature sensor (refer to step 59).

·

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




A

B

17.READ FREEZE FRAME DATA
17.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Suspected Area Proceed to
EVAP (Purge) VSV At least 1 of the 5 sets of freeze frame data is not 0% Purge VSV A
All 5 sets of freeze frame data are 0% - B


HINT:

If the purge VSV is stuck closed, air fuel ratio compensation by the purge VSV is incorrectly adjusted, and then the air fuel ratio becomes lean and the engine may stall.



A

18.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL)

B

27.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
18.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A255085C02
1.705,1.288 1.984,0.172 1.984,0.172 2.285,0.172 false 0.825,2.056 0.935,3.034 0.935,3.034 1.124,3.034 false 2.336,0.112 2.689,0.324 0.352,0.212 10 *1 1.163,2.952 1.368,3.171 0.205,0.219 10 *2
*1 Purge VSV
*2 Fuel Vapor Feed Hose (to Canister)


Disconnect the fuel vapor feed hose (on the canister side) of the purge VSV.


b.

Connect the intelligent tester to the DLC3.


c.

Start the engine.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

Powertrain > Engine and ECT > Active Test
Tester Display
Activate the VSV for Evap Control
50004 234 6

f.

Operate the purge VSV and check the air flow.

OK:
Activate the VSV for Evap Control Specified Condition
ON Air flows
OFF Air does not flow



Result:
Result Proceed to
Abnormal A
Normal B


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Even if the results are normal, the purge VSV may have been malfunctioning. Continue this inspection procedure until step 32, and if there are no problems with other parts, replace the purge VSV (refer to step 59).




A

19.INSPECT PURGE VSV

B

27.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
19.INSPECT PURGE VSV

Result:
Proceed to
OK
NG



OK

20.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)

NG

20.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)
a.

Check the harnesses and connectors, referring to DTC P0443 inspection procedure.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0443


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.



Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

REPAIR POWER SOURCE CIRCUIT (PURGE VSV POWER SOURCE)

21.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Check the harnesses and connectors, referring to DTC P0443 inspection procedure.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0443


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Calculate Load 110% or higher of the current value of the vehicle*1 Mass air flow meter sub-assembly A
AFS Voltage B1S1 Below 3.3 V*2
·

Air fuel ratio sensor

·

Harness and connector

·

Actual air fuel ratio abnormal


B
Both freeze frame data items listed above Values are other than above - C


HINT:
·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N (neutral)) and compare these data with the freeze frame data.

·

*1: If the mass air flow meter sub-assembly is malfunctioning and incorrectly measures the intake air volume to be higher than the actual volume of air flowing through the intake manifold, the freeze frame data will show a high engine load value.

·

*2: As the air fuel ratio sensor output is low before the sensor warms up, the value at that time cannot be used for diagnosis. If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air fuel ratio is rich, the actual air fuel ratio will become lean and the engine may stall.




A

23.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY

B

24.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

C

29.READ FREEZE FRAME DATA
23.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
a.

Remove the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL


b.

Check for foreign matter in the air flow passage of the mass air flow meter sub-assembly.


Result:
Result Proceed to
Visible foreign matter is present A
Visible foreign matter is not present B


HINT:
·

Even if the results are normal, the mass air flow meter sub-assembly may have been malfunctioning. Continue this inspection procedure until step 34, and if there are no problems with other parts, replace the mass air flow meter sub-assembly (refer to step 59).

·

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




A

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

B

29.READ FREEZE FRAME DATA
24.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.
A280723E13
1.302,0.615 1.844,0.844 0.542,0.229 10 12.5% 1.25,0.938 1.75,1.156 0.5,0.219 10 -12.5% 0.615,2.208 1.75,2.417 1.135,0.208 10 Higher than 3.4 V 0.531,3.781 1.74,3.99 1.208,0.208 10 Higher than 0.55 V 0.938,2.583 1.719,2.792 0.781,0.208 10 Below 3.1 V 0.938,4.146 1.75,4.365 0.813,0.219 10 Below 0.4 V 1.031,0.25 2.115,0.458 1.083,0.208 10 Injection Volume 0.635,1.771 3.031,1.99 2.396,0.219 10 Air Fuel Ratio Sensor Output Voltage 0.698,3.313 3.115,3.531 2.417,0.219 10 Heated Oxygen Sensor Output Voltage

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
AFS Voltage B1S1
O2S B1S2
50004 234 2 35,44

f.

Change the fuel injection volume using the tester, and monitor the voltage output of the air fuel ratio and heated oxygen sensors displayed on the tester.

Standard:
Tester Display Specified Condition
Control the Injection Volume for A/F Sensor (12.5%) Air fuel ratio sensor output voltage is below 3.1 V
Control the Injection Volume for A/F Sensor (-12.5%) Air fuel ratio sensor output voltage is higher than 3.4 V


Result:
Result Proceed to
Abnormal A
Normal B


HINT:
·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

Even if the results are normal, the air fuel ratio sensor may have been malfunctioning. Continue this inspection procedure until step 34, and if there are no problems with other parts, replace the air fuel ratio sensor (refer to step 59).





A

25.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)

B

29.READ FREEZE FRAME DATA
25.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)
a.

Check the harnesses and connectors, referring to DTC P0031 inspection procedure.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0031

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

26.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

REPAIR POWER SOURCE CIRCUIT (AIR FUEL RATIO SENSOR POWER SOURCE)

26.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Check the harnesses and connectors, referring to DTC P2237 inspection procedure.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P2237

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

d.

When performing the Active Test, check for an operating sound from the fuel pump.

OK:
Control the Fuel Pump / Speed Specified Condition
ON Operating sound heard
OFF Operating sound not heard



Result:
Result Proceed to
Abnormal A
Normal B


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.

·

If the fuel pump operating noise is abnormal, proceed to step 28.




A

28.INSPECT FUEL PUMP (RESISTANCE)

B

32.CHECK FUEL SYSTEM
28.INSPECT FUEL PUMP (RESISTANCE)
a.

Inspect the fuel pump.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL PUMP>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

29.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions present when the DTC was stored which are recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Proceed to
Initial Engine Coolant Temp, Initial Intake Air Temp Difference in temperature between each item is below 10°C (18°F)*1 A
Difference in temperature between each item is 10°C (18°F) or higher*2 B


HINT:
·

*1: A long time had elapsed after stopping the engine.

·

*2: A long time had not elapsed after stopping the engine.




A

30.READ FREEZE FRAME DATA

B

33.READ FREEZE FRAME DATA
30.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions present when the DTC was stored which are recorded in the freeze frame data.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA

A217929E30
0.229,0.854 3.083,1.521 2.854,0.667 10 Engine Coolant Temperature Increase after Engine Start (Engine Coolant Temperature - Engine Coolant Temperature at Engine Start) 3.427,0.042 3.719,0.24 0.292,0.198 10 (°C) 5.604,2.115 6.219,2.281 0.615,0.167 10 (Minutes) 5.125,1.75 5.313,1.958 0.188,0.208 10 A 4.958,0.833 5.24,1.083 0.281,0.25 10 C 3.885,0.542 4.125,0.75 0.24,0.208 10 B 3.563,2.385 5.573,2.542 2.01,0.156 10 Time Elapsed after Engine Start


Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Initial Engine Coolant Temp, Coolant Temp, Engine Run Time Range A
·

Engine coolant temperature sensor

·

Thermostat


A
Range B Engine coolant temperature sensor B
Range C - C


HINT:

This step is not directly related to engine stall.



A

31.INSPECT THERMOSTAT

B

34.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

C

60.CLEAR DTC
31.INSPECT THERMOSTAT

Result:
Result Proceed to
Abnormal A
Normal B


HINT:

This step is not directly related to engine stall.



A

B

34.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
32.CHECK FUEL SYSTEM
a.

Check for foreign matter such as iron particles around the fuel pump, and for signs that the fuel pump was stuck.


Result:
Result Proceed to
There is foreign matter or signs that fuel pump was stuck A
There is no foreign matter and no signs that fuel pump was stuck B


HINT:

If there is foreign matter such as iron particles on the fuel pump, remove the foreign matter.



A

REPAIR OR REPLACE FUEL SYSTEM

B

59.REPLACE MALFUNCTIONING PARTS
33.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Coolant Temp 120°C (248°F) or higher Engine coolant temperature sensor A
Engine coolant temperature is lower than outside temperature* by 15°C (27°F) or higher Engine coolant temperature sensor
Both freeze frame data items listed above Values are other than above - B


HINT:

*: Use an actual outside temperature estimated from the Initial Intake Air, Ambient Temp for A/C, and (if possible) the weather when the DTC was detected.



A

34.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

60.CLEAR DTC
34.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Result Proceed to
Abnormal A
Normal B


HINT:
·

Even if the results are normal, the engine coolant temperature sensor may have been malfunctioning. If there are no problems with other parts, replace the engine coolant temperature sensor (refer to step 59).

·

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




A

B

59.REPLACE MALFUNCTIONING PARTS
35.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Total of ISC Learning Value and ISC Feedback Value Below 80% of the current value of the vehicle*1 Throttle with motor body assembly A
120% or higher of the current value of the vehicle*2 B
From 80 to 120% of the current value of the vehicle - C


HINT:
·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N (neutral)) and compare these data with the freeze frame data.

·

*1: If the throttle with motor body assembly has a temporary problem in which it cannot fully close, the intake air volume and engine speed increase. As a result, the ISC learning amount becomes less than the standard. At this time, if the throttle with motor body assembly returns to normal and fully closes, the intake air volume will be insufficient and the engine may stall.

·

*2: If carbon accumulates on the throttle with motor body assembly and the intake air volume decreases, the ISC learning amount is increased to maintain the idle speed. If this situation continues, the ISC learning amount reaches the upper limit, the idle speed cannot be maintained causing idling to become unstable, and the engine may stall.




A

36.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY

B

37.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY

C

38.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)
36.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY
a.

Check for foreign matter and signs that the throttle with motor body assembly was stuck, and also check that the valve and shaft move smoothly during operation.


Result:
Result Proceed to
Abnormal A
Normal B


HINT:
·

Even if the results are normal, the throttle with motor body assembly may have been malfunctioning. Continue this inspection procedure until step 42, and if there are no problems with other parts, replace the throttle with motor body assembly (refer to step 59).

·

Perform "Inspection After Repair" after replacing the throttle with motor body assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




A

REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

B

38.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)
37.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY
a.

Check if carbon is in the air flow passage of the throttle with motor body assembly.


Result:
Result Proceed to
Carbon in passage A
No carbon in passage B


HINT:
·

Even if the results are normal, the throttle with motor body assembly may have been malfunctioning. Continue this inspection procedure until step 42, and if there are no problems with other parts, replace the throttle with motor body assembly (refer to step 58).

·

Perform "Inspection After Repair" after replacing the throttle with motor body assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




A

REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

B

38.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)
38.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)
a.

Perform the Active Test, referring to DTC P0011 inspection procedure.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0011


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.

·

If the camshaft timing oil control valve assembly (for intake camshaft) is stuck at the advanced side, the valve overlap increases and combustion worsens due to the internal EGR which may cause rough idle or cause the engine to stall.



Result:
Proceed to
OK
NG



OK

39.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT EXHAUST LINEAR)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

39.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT EXHAUST LINEAR)
a.

Perform the Active Test, referring to DTC P0014 inspection procedure.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0014


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.

·

If the camshaft timing oil control valve assembly (for exhaust camshaft) is stuck at the retard side, the valve overlap increases and combustion worsens due to the internal EGR which may cause rough idle or cause the engine to stall.



Result:
Proceed to
OK
NG



OK

40.READ FREEZE FRAME DATA

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)

40.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Suspected Area Proceed to
IGN Advance Knock Correct Learn Value
Differs from the current value of the vehicle by 10 deg or higher Below 3°CA
·

Engine coolant temperature sensor

·

Mass air flow meter sub-assembly

·

Knock control sensor


A
3°CA or higher - B
Differs from the current value of the vehicle by less than 10 deg - -


HINT:
·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N (neutral)) and compare these data with the freeze frame data.

·

Even if the results are normal, the knock control sensors may have been malfunctioning. If there are no problems with other parts, replace the knock control sensors (refer to step 59).




A

41.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

59.REPLACE MALFUNCTIONING PARTS
41.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

42.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (INTAKE AIR TEMPERATURE SENSOR)

NG

42.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (INTAKE AIR TEMPERATURE SENSOR)
a.

Inspect the mass air flow meter sub-assembly (intake air temperature sensor).

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>MASS AIR FLOW METER>INSPECTION


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly or knock control sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

NG

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

43.CHECK TERMINAL VOLTAGE (#10, #20, #30 AND/OR #40)
a.

Check the harnesses and connectors, referring to DTC P0300 inspection procedure.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0300


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)



Result:
Proceed to
OK
NG



OK

44.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)

NG

44.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
a.

Check the harnesses and connectors, referring to DTC P0351 inspection procedure.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0351


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)



Result:
Proceed to
OK
NG



OK

45.READ FREEZE FRAME DATA

NG

REPAIR IGNITION COIL POWER SOURCE CIRCUIT

45.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Idle Spark Advn Ctrl (#1 to #4) At least one cylinder shows a value of 4°CA or higher
·

Fuel injector system

·

Ignition coil system


A
All cylinders show a value of less than 4°CA - B



A

46.READ VALUE USING INTELLIGENT TESTER (IDLE SPARK ADVN CTRL #)

B

47.READ FREEZE FRAME DATA
46.READ VALUE USING INTELLIGENT TESTER (IDLE SPARK ADVN CTRL #)
a.

Change the location of the ignition coil assembly for the cylinder whose Idle Spark Advn Ctrl (#1 to #4) was 4°CA or more in step 45.


b.

Connect the intelligent tester to the DLC3.


c.

Start the engine.


d.

Using the tester, select [Idle Spark Advn Ctrl (#1 to #4)] of the Data List.


Result:
Result Proceed to
Same as result in step 45 A
Different from result in step 45 B


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Perform "Inspection After Repair" after replacing the ignition coil assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




A

47.READ FREEZE FRAME DATA

B

47.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Suspected Area Proceed to
A/C Signal Air Conditioner FB Val Power Steering Signal
A/C Signal display changes from OFF to ON Value displayed for Air Conditioner FB Val increases Does not change from OFF A/C system B
*1
C
*2
Changes from OFF to ON Power steering system A
*3
D
*4
A/C Signal display does not change from OFF Value displayed for Air Conditioner FB Val does not increase Changes from OFF to ON
Does not change from OFF -


*1: for automatic air conditioning system.

*2: for manual air conditioning system.

*3: for Automatic Transaxle models.

*4: for Manual Transaxle models.


HINT:
·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N (neutral)) and compare these data with the freeze frame data.

·

The normal value for the ISC learning amount is engine displacement (liters) x 0.9.

·

Even if the results are normal, the power steering system or the air conditioning system may have been malfunctioning. Continue this inspection procedure until step 50, and if there are no problems with other parts, inspect the power steering system and the air conditioning system (refer to step 59).




A

48.CHECK AUTOMATIC TRANSAXLE ASSEMBLY

B

C

D

51.READ FREEZE FRAME DATA
48.CHECK AUTOMATIC TRANSAXLE ASSEMBLY
a.

Start the engine.


b.

Move the shift lever to R and confirm that the vehicle can move rearward.

OK:

The vehicle can move rearward.



Result:
Proceed to
OK
NG



OK

49.READ FREEZE FRAME DATA

NG

49.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Suspected Area Proceed to
Electrical Load Signal 1 (3) Electric Load Feedback Val Difference between Engine Speed and SPD (NT) Vehicle Speed
Electrical Load Signal 1 (3) display changes from OFF to ON*1, or value displayed for Electric Load Feedback Val increases*1 Value displayed for Electric Load Feedback Val changes - - Electrical load signal circuit A
Value displayed for Electric Load Feedback Val does not change At least 1 of the 5 sets of freeze frame data is below 100 rpm Below 15 km/h (9 mph) A/T system B
15 km/h (9 mph) or more - C
All 5 sets of freeze frame data are 100 rpm or higher - -
Electrical Load Signal 1 (3) display does not change from OFF, or value displayed for Electric Load Feedback Val does not increase - At least 1 of the 5 sets of freeze frame data is below 100 rpm Below 15 km/h (9 mph) A/T system B
15 km/h (9 mph) or more - C
All 5 sets of freeze frame data are 100 rpm or higher - -


HINT:
·

*1: If the Electrical Load Signal 1 (3) display changes from OFF to ON or the Electric Load Feedback Val increases, it probably is a malfunction due to a change in electrical load. Check the generator and the continuity and connections between the generator and ECM.

·

If the vehicle speed is 15 km/h (9 mph) or less and the difference between Engine Speed and SPD (NT) is 100 rpm or less, inspect the automatic transaxle. (Depending on the rate of vehicle deceleration, the engine speed may have decreased due to the A/T lock-up release being late.)

·

The normal value for the ISC learning amount is engine displacement (liters) x 0.9.

·

Even if the results are normal, the electrical load signal system and/or the A/T system may have been malfunctioning. Continue this inspection procedure until step 51, and if there are no problems with other parts, inspect the electrical load signal system and/or the A/T system (refer to step 59).




A

B

C

50.READ FREEZE FRAME DATA
50.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Suspected Area Proceed to
Shift SW Status (P or N Range) Neutral Position SW Signal
P and N position are both OFF in at least one data set ON when Shift SW Status D or R Park/Neutral position switch assembly A
OFF when Shift SW Status D or R A/T system B
All 5 sets of freeze frame data are ON - - C


HINT:

Even if the results are normal, the park/neutral position switch assembly and/or A/T system may have been malfunctioning. If there are no problems with other parts, inspect the park/neutral position switch assembly and/or A/T system (refer to step 59).



A

B

C

59.REPLACE MALFUNCTIONING PARTS
51.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Suspected Area Proceed to
Electrical Load Signal 1 (3) Electric Load Feedback Val
Electrical Load Signal 1 (3) display changes from OFF to ON*1, or value displayed for Electric Load Feedback Val increases*1 Value displayed for Electric Load Val changes Electrical load signal circuit A
Value displayed for Electric Load Val does not change - B
Electrical Load Signal 1 (3) display does not change from OFF, or value displayed for Electric Load Feedback Val does not increase - - B


HINT:
·

*1: If the Electrical Load Signal 1 (3) display changes from OFF to ON or the Electric Load Feedback Val increases, it probably is a malfunction due to a change in electrical load. Check the generator and the continuity and connections between the generator and ECM.

·

The normal value for the ISC learning amount is engine displacement (liters) x 0.9.

·

Even if the results are normal, the electrical load signal system may have been malfunctioning. If there are no problems with other parts, inspect the electrical load system (refer to step 59).




A

B

59.REPLACE MALFUNCTIONING PARTS
52.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Throttle Sensor Position, Calculate Load Calculate Load decreases while Throttle Sensor Position increases Mass air flow meter sub-assembly A
Calculate Load does not decrease while Throttle Sensor Position increases - B



A

53.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY

B

54.CHECK TERMINAL VOLTAGE (#10, #20, #30 AND/OR #40)
53.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
a.

Remove the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL


b.

Check for foreign matter in the air flow passage of the mass air flow meter sub-assembly.


Result:
Result Proceed to
Visible foreign matter is present A
Visible foreign matter is not present B


HINT:
·

Even if the results are normal, the mass air flow meter sub-assembly may have been malfunctioning. Continue this inspection procedure until step 58, and if there are no problems with other parts, replace the mass air flow meter sub-assembly (refer to step 59).

·

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




A

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

B

54.CHECK TERMINAL VOLTAGE (#10, #20, #30 AND/OR #40)
54.CHECK TERMINAL VOLTAGE (#10, #20, #30 AND/OR #40)
a.

Check the harnesses and connectors, referring to DTC P0300 inspection procedure.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0300


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)



Result:
Proceed to
OK
NG



OK

55.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)

NG

55.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
a.

Check the harnesses and connectors, referring to DTC P0351 inspection procedure.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0351


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)



Result:
Proceed to
OK
NG



OK

56.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)

NG

REPAIR IGNITION COIL POWER SOURCE CIRCUIT

56.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

d.

When performing the Active Test, check for an operating sound from the fuel pump.

OK:
Control the Fuel Pump / Speed Specified Condition
ON Operating sound heard
OFF Operating sound not heard



Result:
Result Proceed to
Abnormal A
Normal B


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.

·

If the fuel pump operating noise is abnormal, proceed to step 58.




A

57.INSPECT FUEL PUMP

B

58.CHECK FUEL SYSTEM
57.INSPECT FUEL PUMP
a.

Inspect the fuel pump.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL PUMP>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

58.CHECK FUEL SYSTEM
a.

Check for foreign matter such as iron particles around the fuel pump, and for signs that the fuel pump was stuck.


Result:
Result Proceed to
There is foreign matter or signs that fuel pump was stuck A
There is no foreign matter and no signs that fuel pump was stuck B


HINT:

If there is foreign matter such as iron particles on the fuel pump, remove the foreign matter.



A

REPAIR OR REPLACE FUEL SYSTEM

B

59.REPLACE MALFUNCTIONING PARTS
59.REPLACE MALFUNCTIONING PARTS
a.

If the malfunction could not be identified in steps 3 to 21, 27, 28, 32, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.

Performed Step Inspection or Part to Replace
Step 6 Brake booster assembly replacement
Step 8 Mass air flow meter sub-assembly replacement
Step 9 Air fuel ratio sensor replacement
Step 16 Engine coolant temperature sensor replacement
Step 18 Purge VSV replacement
Step 32 Fuel pump replacement


b.

If the malfunction could not be identified in steps 22 to 26, 29 to 31, 33, 34, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.

Performed Step Inspection or Part to Replace
Step 23 Mass air flow meter sub-assembly replacement
Step 24 Air fuel ratio sensor replacement
Step 34 Engine coolant temperature sensor replacement


c.

If the malfunction could not be identified in steps 35 to 42, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.

Performed Step Inspection or Part to Replace
Step 36 and 37 Throttle with motor body assembly replacement
Step 40 Knock control sensor replacement


d.

If the malfunction could not be identified in steps 43 to 51, inspect and repair the part which is suspected to be malfunctioning according to the step where an inspection was performed.

Performed Step Inspection or Part to Replace
Step 47 A/C system inspection and repair
Power steering system inspection and repair
Step 48 A/T system inspection and repair
Step 49 Electrical load signal system inspection and repair
A/T system inspection and repair
Step 50 Park/Neutral position switch inspection and repair
A/T system inspection and repair
Step 51 Electrical load signal system inspection and repair


e.

If the malfunction could not be identified in steps 52 to 58, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.

Performed Step Inspection or Part to Replace
Step 53 Mass air flow meter sub-assembly replacement

HINT:
·

Referring to the chart, inspect and repair or replace the part from the step where an inspection was performed.

·

Perform "Inspection After Repair" after replacing or servicing parts related to engine operation. Refer to detailed information in Initialization.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

60.CLEAR DTC
60.CLEAR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

61.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
61.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check if engine stall symptoms are present.

HINT:

If any engine stall symptoms are present, recheck for DTCs and freeze frame data and perform an inspection.



Result:
Proceed to
OK
NG



OK

END

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS