Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2015.04–2016.05
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P1603  Engine Stall History  P1605  Rough Idling  


DESCRIPTION

P1603

After starting the engine, this DTC is stored when the engine stops without the engine switch being operated.

Using the GTS, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

It is necessary to check if the vehicle has run out of fuel in the past before performing troubleshooting, as this DTC is also stored when the engine stalls due to running out of fuel.

P1605

This DTC is stored if the engine speed drops below the set speed.

Using the GTS, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

It is necessary to check if the vehicle has run out of fuel in the past before performing troubleshooting, as this DTC is also stored when idling is unstable due to running out of fuel.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1603 Engine Stall History After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the engine, with the engine running, the engine stops (the engine speed drops to 200 rpm or less) without the engine switch being operated for 0.5 seconds or more (1 trip detection logic).
·

Air leak in intake system

·

Purge VSV

·

Brake booster hose not connected properly

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Wire harness or connector

·

Air fuel ratio sensor

·

Power supply circuit (purge VSV, fuel injector assembly, ignition coil assembly)

·

Fuel pump

·

Fuel pump control system

·

Fuel line (fuel filter, pipes and hoses)

·

Throttle with motor body assembly

·

Camshaft timing oil control valve assembly

·

Air conditioning system

·

Power steering system

·

Electrical load signal system

·

A/T system

·

Park/Neutral position switch assembly

·

Thermostat

·

ECM


Does not come on DTC stored
P1605 Rough Idling After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to 400 rpm or less (1 trip detection logic).
·

Air leak in intake system

·

Purge VSV

·

Brake booster hose not connected properly

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Wire harness or connector

·

Air fuel ratio sensor

·

Power supply circuit (purge VSV, fuel injector assembly, ignition coil assembly)

·

Fuel pump

·

Fuel pump control system

·

Fuel line (fuel filter, pipes and hoses)

·

Throttle with motor body assembly

·

Camshaft timing oil control valve assembly

·

Knock control sensor

·

Ignition coil assembly (No. 1 to No. 6 cylinder)

·

Fuel injector assembly

·

Spark plug(s)

·

Air conditioning system

·

Power steering system

·

Electrical load signal system

·

A/T system

·

Park/Neutral position switch assembly

·

ECM


Does not come on DTC stored

Reference waveforms showing a normal cold engine start


A258932


Reference waveforms showing a normal warm engine start


A258933


Reference values when there is an air leak in the intake system during rough idling


Freeze Frame Data P1605 Rough Idling
Parameter -3 -2 -1 0 1 Unit
Engine Speed 647 649 586 378 182 rpm
Calculate Load 26.2 26.2 29.1 42.6 58.6 %
Vehicle Load 11.7 11.7 12.1 48.7 61.2 %
MAF 2.87 2.87 2.87 6.23 3.04 gm/sec
Atmosphere Pressure 0 0 0 0 0 kPa
Coolant Temp 187 187 187 187 187 F
Intake Air 109 109 109 109 109 F
Battery Voltage 13.515 13.515 13.264 12.892 12.792 V
Throttle Sensor Volt % 14.5 14.5 14.5 16.8 17.2 %
Throttl Sensor #2 Volt % 46.2 46.2 46.2 48.4 49.2 %
Throttle Sensor Position 0.0 0.0 0.0 0.0 0.0 %
Throttle Motor DUTY 14.5 14.5 14.5 17.2 17.2 %
Injector (Port) 2159 2161 2148 2190 2190 μs
Injection Volum (Cylinder 1) 0.093 0.093 0.093 0.095 0.095 ml
Fuel Pump Duty 58.6 58.6 58.6 58.6 58.6 %
EVAP (Purge) VSV 13.3 13.3 13.3 13.3 13.3 %
Evap Purge Flow 2.9 2.9 2.9 3.2 3.2 %
Purge Density Learn Value 0.891 0.891 0.891 0.891 0.891
EVAP Purge VSV OFF OFF OFF OFF OFF
Purge Cut VSV Duty 8.5 8.5 8.5 8.5 8.5 %
Target Air-Fuel Ratio 0.998 0.998 0.998 0.998 0.998
AF Lambda B1S1 0.999 0.997 1.001 1.038 1.118
AF Lambda B2S1 0.997 0.994 0.999 1.036 1.112
AFS Voltage B1S1 3.258 3.242 3.284 3.521 3.715 V
AFS Voltage B2S1 3.251 3.306 3.324 3.497 3.689 V
O2S B1S2 0.740 0.740 0.740 0.740 0.740 V
O2S B2S2 0.760 0.760 0.760 0.760 0.760 V
Short FT #1 -1.563 -1.563 -1.563 -1.563 -1.563 %
Long FT #1 6.250 6.250 6.250 6.250 6.250 %
Total FT #1 0.054 0.054 0.054 0.054 0.054
Sort FT #2 -0.782 -0.782 -0.782 -0.782 -0.782 %
Long FT #2 7.031 7.031 7.031 7.031 7.031 %
Total FT #2 0.062 0.062 0.062 0.062 0.062
Fuel System Status #1 CL CL CL CL CL
Fuel System Status #2 CL CL CL CL CL
IGN Advance 22.0 22.0 22.5 23.5 23.5 deg
Knock Feedback Value -1.5 -1.5 -1.5 -1.5 -1.5 deg(CA)
Knock Correct Learn Value 17.0 17.0 17.0 17.0 17.0 deg(CA)
Starter Signal OFF OFF OFF OFF OFF


WIRING DIAGRAM

Refer to DTC P0351 for the ignition coil circuit (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0351).

Refer to DTC P0443 for the purge VSV circuit (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0443).

Refer to DTC P2195 for the air fuel ratio sensor circuit (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P2195).

Refer to Fuel Pump Control Circuit (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>Fuel Pump Control Circuit).

Refer to Fuel Injector Circuit (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>Fuel Injector Circuit).

CAUTION / NOTICE / HINT

HINT:
·

In contrast to normal malfunction diagnosis for components, circuits and systems, DTCs P1603 and P1605 are used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine stall.

As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.

·

If any other DTCs are output, perform troubleshooting for those DTCs first.

·

Use any information from the customer problem analysis about the condition of the vehicle at the time when the problem occurred (how the engine stopped, conditions when the engine was restarted, etc.) as a reference.

Symptom Suspected Area
Engine vibration occurs and engine stops Air fuel ratio abnormal
Engine stops with no engine vibration Ignition system, injection stoppage, high load from external parts
Engine can be started with accelerator pedal depressed Insufficient air volume
Rough idling after engine started Air fuel ratio abnormal, abnormal combustion

·

Read freeze frame data using the GTS. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

·

When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

·

When DTC P1603 (Engine Stall History) is stored, DTC P1605 (Rough Idling) is also stored. When confirming freeze frame data, check DTC P1605. (The ECM stores DTC P1605 first. Therefore, the 5 sets of freeze frame data can be confirmed through DTC P1605, enabling the technician to obtain more information.)

·

When confirming freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.

·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.

·

Inspections take into account the fact that the malfunction may not have reoccurred and place emphasis on checking the vehicle conditions present at the time when the malfunction occurred.

·

When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.



Inspection flow:

Using freeze frame data, narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred.


P1603:

A224366E14
0.219,0.771 1.146,1.24 0.927,0.469 10 false While idling or while driving? 1.823,0.781 3.156,1.479 1.333,0.698 10 false Did the engine speed decrease slowly or rapidly when engine stall occurred? 0.188,0.604 0.375,0.792 0.188,0.188 10 false 1: 1.823,0.604 2.01,0.792 0.188,0.188 10 false 2: 3.927,0.781 4.958,1.302 1.031,0.521 10 false Was the air fuel ratio abnormal or normal? 3.927,0.604 4.115,0.792 0.188,0.188 10 false 3: 5.958,0.75 6.906,0.917 0.948,0.167 10 false Intake air leak 5.781,1.76 7.031,1.927 1.25,0.167 10 false Sensor malfunction 1.24,5.833 2.49,6 1.25,0.167 10 false Sensor malfunction 5.75,2.76 7.063,2.927 1.313,0.167 10 false Fuel supply problem 1.219,7.823 2.531,7.99 1.313,0.167 10 false Fuel supply problem 6.031,3.458 6.74,3.813 0.708,0.354 10 false Air volume insufficient 5.948,4.469 6.875,4.948 0.927,0.479 10 false Ignition timing incorrect 3.406,4.479 4.49,4.823 1.083,0.344 10 false Injection and ignition stoppage 1.333,6.552 2.417,6.896 1.083,0.344 10 false Injection and ignition stoppage 3.5,5.479 4.396,5.823 0.896,0.344 10 false Load from external parts 1.313,0.135 1.792,0.417 0.479,0.281 10 false Idling 0.094,2.542 0.552,2.708 0.458,0.167 10 false Driving 2.969,0.135 4.156,0.302 1.188,0.167 10 false Decreased Slowly 1.156,2.542 2.396,2.74 1.24,0.198 10 false Decreased Rapidly 5.031,0.135 5.698,0.323 0.667,0.188 10 false Abnormal 3.833,2.542 4.333,2.708 0.5,0.167 10 false Normal

1:
·

If the engine stalled when the intake air volume was low (during idling or deceleration), there may be a decrease in torque due to an incorrect air fuel ratio, etc.

·

If the engine stalled when the intake air volume was high (during driving or acceleration), there may be a major malfunction such as continuous misfire due to ignition stoppage, fuel injection stoppage, etc. and the torque drops to zero.


2:
·

If the engine speed decreased slowly, there may have been a decrease in torque due to an air fuel ratio that was incorrect (by approximately 20 to 30%), etc.

·

If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.


3:
·

If the air fuel ratio was abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.

·

If the air fuel ratio was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.


P1603 inspection flow: Narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred (freeze frame data).

Vehicle State Engine Speed Suspected Area Primary Parts to Inspect Procedure
Idling or decelerating Slowly decreases and engine stalls Air fuel ratio abnormal Air suction
·

Intake system connections

·

Purge VSV system

·

Brake booster assembly


3 to 6
Sensor malfunction (value from sensor too lean)
·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Air fuel ratio sensor system


7 to 16
Sensor malfunction (value from sensor too rich) 22 to 26,
30 to 34
Fuel supply problem
·

Fuel pump control system

·

Purge VSV system

·

Fuel line

·

ECM


17 to 21,
27 to 29
Intake air volume insufficient ISC flow rate
·

Throttle with motor body assembly (ISC valve)


35 to 37
Excessive valve overlap
·

Camshaft timing oil control valve assembly


38, 39
Ignition timing incorrect Does not operate as expected
·

Engine coolant temperature sensor

·

Knock control sensor

·

Mass air flow meter sub-assembly


40 to 42
Rapidly decreases and engine stalls Ignition and injection stops (electrical system malfunction) Power temporarily cut
·

Power supply circuit (fuel injector assembly, ignition coil assembly)


43, 44
External part malfunctioning Increase in load
·

Air conditioning system

·

Electrical load signal system

·

Power steering system

·

A/T system

·

Park/Neutral position switch assembly


47 to 49
Accelerating - Crankshaft position sensor, VVT sensor malfunction Power temporarily cut
·

Check DTCs


1
Mass air flow meter sub-assembly Foreign matter adhesion
·

Mass air flow meter sub-assembly


51
Fuel supply problem Fuel leak, clog
·

Fuel pump control system

·

Fuel line


54 to 56
Ignition and injection stops (electrical system malfunction) Power temporarily cut
·

Power supply circuit (fuel injector assembly, ignition coil assembly)


52, 53

P1605:

A224367E03
0.498,0.514 0.668,0.688 0.170,0.174 10 1: 0.498,0.71 1.640,1.213 1.142,0.503 10 Did the engine speed decrease slowly or rapidly? 2.819,0.514 2.989,0.688 0.170,0.174 10 2: 2.819,0.71 3.961,1.213 1.142,0.503 10 Was the air fuel ratio abnormal or normal? 5.69,0.715 6.633,0.881 0.943,0.165 10 Intake air leak 5.549,1.727 6.788,1.892 1.239,0.165 10 Sensor malfunction 5.522,2.722 6.799,2.924 1.276,0.202 10 Fuel supply problem 4.034,2.065 4.742,2.384 0.708,0.319 10 Air volume insufficient 3.925,3.05 4.850,3.382 0.924,0.332 10 Ignition timing incorrect 1.582,2.706 2.673,3.057 1.091,0.350 10 Injection and ignition stoppage 1.662,3.707 2.586,4.057 0.924,0.350 10 Load from external parts 1.908,0.876 2.628,1.226 0.721,0.350 10 Decreased Slowly 0.264,1.847 0.984,2.197 0.721,0.350 10 Decreased Rapidly 4.299,0.894 4.945,1.059 0.647,0.165 10 Abnormal 2.776,1.847 3.293,2.012 0.517,0.165 10 Normal

1:
·

If the engine speed decreased slowly, there may have been a decrease in torque due to an air fuel ratio that was incorrect (by approximately 20 to 30%), etc.

·

If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.


2:
·

If the air fuel ratio was abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.

·

If the air fuel ratio was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.


P1605 inspection flow: Narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred (freeze frame data).

Engine Speed Suspected Area Primary Parts to Inspect Procedure
Slowly decreases Air fuel ratio abnormal Air suction
·

Intake system connections

·

Purge VSV system

·

Brake booster assembly


3 to 6
Sensor malfunction (value from sensor too lean)
·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Air fuel ratio sensor system


7 to 16
Sensor malfunction (value from sensor too rich) 22 to 26,
30 to 34
Fuel supply problem
·

Fuel pump control system

·

Purge VSV system

·

Fuel line

·

ECM


17 to 21,
27 to 29
Intake air volume insufficient ISC flow rate
·

Throttle with motor body assembly (ISC valve)


35 to 37
Ignition timing incorrect Does not operate as expected
·

Knock control sensor

·

Engine coolant temperature sensor

·

Mass air flow meter sub-assembly


40 to 42
Rapidly decreases Ignition and injection stops (electrical system malfunction) Power temporarily cut
·

Power supply circuit (fuel injector assembly, ignition coil assembly)


43, 44
External part malfunctioning Increase in load
·

Air conditioning system

·

Power steering system

·

A/T system

·

Park/Neutral position switch assembly


47 to 49

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1603 AND/OR P1605)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P1603 and/or P1605 is output A
DTC P1603 or P1605 and other DTCs are output B



A

2.READ FREEZE FRAME DATA

B

2.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA

Result:
Problem Symptom Freeze Frame Data Item Suspected Area Proceed to
Closed Throttle Position SW Engine Speed Total of Short FT and Long FT
When idling or decelerating, engine speed slowly decreases (and engine stalls) All 5 sets of freeze frame data are ON Decreases slowly*1 All 5 sets of freeze frame data are 15% or higher*2
·

Air suction

·

Sensor malfunction (value from sensor too lean)

·

Fuel supply problem


A
At least 1 of the 5 sets of freeze frame data is -15% or less*3 Sensor malfunction (value from sensor too rich) B
All 5 sets of freeze frame data are between -15% and 15%
·

Intake air volume insufficient

·

Ignition timing incorrect


C
When idling or decelerating, engine speed rapidly decreases (and engine stalls) Decreases rapidly*1 -
·

Injection stoppage, ignition stoppage

·

Load from external parts


D
When accelerating or driving at constant speed, engine stalls*4 At least one is OFF - -
·

Sensor malfunction

·

Injection stoppage, ignition stoppage

·

Fuel supply problem


E


A215381E06
0.072,0.032 2.178,0.197 2.105,0.166 10 Rapid Decrease in Engine Speed 2.333,0.377 2.702,0.561 0.369,0.184 10 (rpm) 2.389,0.723 2.665,0.87 0.277,0.147 10 800 2.389,0.928 2.665,1.075 0.277,0.147 10 600 2.389,1.126 2.665,1.273 0.277,0.147 10 400 2.389,1.331 2.665,1.478 0.277,0.147 10 200 2.548,1.529 2.689,1.676 0.142,0.147 10 0 3.038,1.642 3.236,1.798 0.198,0.156 10 #1 3.472,1.642 3.67,1.798 0.198,0.156 10 #2 3.935,1.642 4.132,1.798 0.198,0.156 10 #3 4.153,1.642 4.351,1.798 0.198,0.156 10 #4 4.377,1.642 4.575,1.798 0.198,0.156 10 #5 4.985,1.105 6.169,1.261 1.184,0.156 10 400 rpm or higher 1.217,1.019 2.123,1.203 0.906,0.184 10 Engine Speed 2.702,1.944 4.816,2.128 2.115,0.184 10 Freeze Frame Data Storage Point

HINT:
·

*1: A rapid decrease in engine speed may be caused by an electrical fault in the shared wiring of all or a number of cylinders, an increase in load from external parts, etc. The engine speed is considered to have decreased rapidly if either of the following conditions applies.

Otherwise, the engine speed is considered to have decreased slowly.

1.

In the freeze frame data, the decrease in engine speed from #3 to #5 is 400 rpm or higher.

2.

In the freeze frame data, the engine speed at #5 is 120 rpm or less.


·

If the vehicle speed is 20 km/h (12 mph) or less and the difference between Engine Speed and SPD (NT) is 100 rpm or less, inspect the automatic transaxle. (Depending on the rate of vehicle deceleration, the engine speed may have decreased due to the A/T lock-up release being late.)

·

*2: When a DTC is stored, feedback compensation increases because the air fuel ratio is determined to be lean.

·

*3: When a DTC is stored, feedback compensation decreases because the air fuel ratio is determined to be rich.

·

*4: This item should be checked when DTC P1603 is output and is not necessary to check when only P1605 is output.





A

3.CHECK INTAKE SYSTEM

B

22.READ FREEZE FRAME DATA

C

35.READ FREEZE FRAME DATA

D

43.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)

E

50.READ FREEZE FRAME DATA
3.CHECK INTAKE SYSTEM
a.

Check for air leaks in the intake system (vacuum hose disconnection, cracks, damaged gaskets, etc.).

Click hereEngine / Hybrid System>2GR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.

·

If Short FT and Long FT are largely different from the normal values when idling (the intake air volume is small) and almost the same as the normal values when racing the engine (the intake air volume is high), air leaks may be present.



OK:

There is no air leaks.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

4.CHECK PURGE VSV

NG

REPAIR OR REPLACE INTAKE SYSTEM

4.CHECK PURGE VSV
a.
A255867C04
1.802,1.969 2.01,3.25 2.01,3.25 2.188,3.25 false 0.802,1.99 0.979,3.25 0.979,3.25 1.125,3.25 false 1.844,0.667 2.042,0.125 2.042,0.125 2.281,0.125 false 2.229,3.135 2.396,3.302 0.167,0.167 10 false *3 1.167,3.177 1.333,3.344 0.167,0.167 10 false *2 2.323,0.021 2.49,0.188 0.167,0.167 10 false *1
*1 Fuel Vapor Feed Hose Assembly (to Canister)
*2 Purge VSV Connector
*3 Purge VSV


Disconnect the fuel vapor feed hose assembly (on the canister side) of the purge VSV.


b.

Start the engine.


c.

Idle the engine.


d.

Disconnect the connector of the purge VSV.


e.

Check if air flows through the purge VSV.

OK:

Air does not flow.


HINT:

When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR



Result:
Proceed to
OK
NG



OK

5.READ FREEZE FRAME DATA

NG

5.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Stop Light Switch At least 1 of the 5 sets of freeze frame data is ON Air suction from brake booster assembly A
All 5 sets of freeze frame data are OFF - B



A

6.READ VALUE USING GTS (SHORT FT #1 AND SHORT FT #2)

B

7.READ FREEZE FRAME DATA
6.READ VALUE USING GTS (SHORT FT #1 AND SHORT FT #2)
A217928E06
0.214,0.569 0.925,0.739 0.711,0.170 10 Depressed 0.093,0.053 0.902,0.209 0.809,0.156 10 Brake Pedal 0.308,1.092 0.936,1.248 0.628,0.156 10 Released 0.114,1.696 2.263,1.852 2.149,0.156 10 Short FT #1 or Short FT #2 2.508,2.227 3.261,2.564 0.753,0.336 10 Change is 10% or less

a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



d.

Idle the engine.


e.

Using the GTS, read [Short FT #1 and Short FT #2] of the Data List while depressing the brake pedal.

Powertrain > Engine > Data List
Tester Display
Short FT #1
Short FT #2
50003 234 25,27
Standard:

Short FT #1 or Short FT #2 changes by 10% or less.


Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C


HINT:
·

Even if the results are normal, the brake booster assembly may have been malfunctioning. Continue this inspection procedure until step 29, and if there are no problems with other parts, replace the brake booster assembly (refer to step 57).

·

When air leaks from the brake booster assembly is present, the feedback compensation increases because the air fuel ratio becomes lean.

·

It is also possible to perform the airtightness inspection to check the brake booster assembly.





A

7.READ FREEZE FRAME DATA

B

REPLACE BRAKE BOOSTER ASSEMBLY

C

REPLACE BRAKE BOOSTER ASSEMBLY

7.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA

Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Calculate Load Less than 90% of the current value of the vehicle*1 Mass air flow meter sub-assembly A
AFS Voltage B1S1 or AFS Voltage B2S1 3.3 V or higher*2
·

Air fuel ratio sensor

·

Wire harness or connector

·

Actual air fuel ratio abnormal


B
Both freeze frame data items listed above Values are other than above - C


HINT:
·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.

·

*1: If the mass air flow meter sub-assembly is malfunctioning, the freeze frame data will show a low engine load value.

·

*2: If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air fuel ratio is lean, the actual air fuel ratio will become rich and the engine may stall.





A

8.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY

B

9.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

C

12.READ FREEZE FRAME DATA
8.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
a.

Remove the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL


b.

Check for foreign matter in the air flow passage of the mass air flow meter sub-assembly.

Result:
Result Proceed to
Visible foreign matter is present A
Visible foreign matter is not present B


HINT:
·

Even if the results are normal, the mass air flow meter sub-assembly may have been malfunctioning. Continue this inspection procedure until step 29, and if there are no problems with other parts, replace the mass air flow meter sub-assembly (refer to step 57).

·

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION





A

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

B

12.READ FREEZE FRAME DATA
9.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
A280723E18
1.313,0.604 1.74,0.833 0.427,0.229 10 false 12.5% 1.271,0.938 1.823,1.188 0.552,0.25 10 false -12.5% 0.615,2.208 1.75,2.417 1.135,0.208 10 false Higher than 3.4 V 0.531,3.781 1.74,3.99 1.208,0.208 10 false Higher than 0.55 V 0.938,2.583 1.719,2.792 0.781,0.208 10 false Below 3.1 V 0.938,4.146 1.75,4.365 0.813,0.219 10 false Below 0.4 V 1.031,0.25 2.115,0.458 1.083,0.208 10 false Injection Volume 0.635,1.771 3.031,1.99 2.396,0.219 10 false Air Fuel Ratio Sensor Output Voltage 0.698,3.313 3.115,3.531 2.417,0.219 10 false Heated Oxygen Sensor Output Voltage

a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / All Data / AFS Voltage B1S1 and AFS Voltage B2S1.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
AFS Voltage B1S1
AFS Voltage B2S1
50004 234 2 35,37

f.

Change the fuel injection volume using the GTS, and monitor the voltage output of the air fuel ratio sensors displayed on the GTS.

Standard:
GTS Display Specified Condition
Control the Injection Volume for A/F Sensor (12.5%) Air fuel ratio sensors output voltage is below 3.1 V
Control the Injection Volume for A/F Sensor (-12.5%) Air fuel ratio sensors output voltage is higher than 3.4 V


Result:
Result Proceed to
Abnormal A
Normal B


HINT:
·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

Even if the results are normal, the air fuel ratio sensor may have been malfunctioning. Continue this inspection procedure until step 29, and if there are no problems with other parts, replace the air fuel ratio sensor (refer to step 57).





A

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)

B

12.READ FREEZE FRAME DATA
10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)
a.

Check the harnesses and connectors, referring to DTC P0031 inspection procedure.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0031

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

REPAIR POWER SOURCE CIRCUIT (AIR FUEL RATIO SENSOR POWER SOURCE)

11.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Check the harnesses and connectors, referring to DTC P2237 inspection procedure.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P2237

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA

Result:
Freeze Frame Data Item Result Proceed to
Initial Engine Coolant Temp, Initial Intake Air Temp Difference in temperature between each item is below 10°C (18°F)*1 A
Difference in temperature between each item is 10°C (18°F) or higher*2 B


HINT:
·

*1: A long time had elapsed after stopping the engine.

·

*2: A long time had not elapsed after stopping the engine.





A

13.READ FREEZE FRAME DATA

B

15.READ FREEZE FRAME DATA
13.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA

A217929E21
0.229,0.856 3.082,1.519 2.853,0.663 10 Engine Coolant Temperature Increase after Engine Start (Engine Coolant Temperature - Engine Coolant Temperature at Engine Start) 3.423,0.037 3.718,0.235 0.295,0.198 10 (°C) 5.609,2.116 6.223,2.286 0.615,0.17 10 (Minutes) 5.16,1.69 5.317,1.846 0.156,0.156 10 A 4.964,0.779 5.121,0.935 0.156,0.156 10 C 3.891,0.493 4.047,0.649 0.156,0.156 10 B 3.563,2.39 5.574,2.547 2.01,0.156 10 Time Elapsed after Engine Start

Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Initial Engine Coolant Temp, Coolant Temp, Engine Run Time Range A
·

Engine coolant temperature sensor

·

Thermostat


A
Range B Engine coolant temperature sensor B
Range C - C


HINT:

This step is not directly related to engine stall.




A

14.INSPECT THERMOSTAT

B

16.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

C

17.READ FREEZE FRAME DATA
14.INSPECT THERMOSTAT
a.

Inspect the thermostat.

Click hereEngine / Hybrid System>2GR-FE COOLING>THERMOSTAT>INSPECTION

Result:
Result Proceed to
Abnormal A
Normal B


HINT:

This step is not directly related to engine stall.




A

B

16.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
15.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA

Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Coolant Temp 120°C (248°F) or higher Engine coolant temperature sensor A
Engine coolant temperature is lower than outside temperature* by 15°C (27°F) or higher Engine coolant temperature sensor
Freeze frame data item listed above Values are other than above - B


HINT:

*: Use an actual outside temperature estimated from the Initial Intake Air, Ambient Temp for A/C, and (if possible) the weather when the DTC was detected.




A

16.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

17.READ FREEZE FRAME DATA
16.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION

HINT:
·

Even if the results are normal, the engine coolant temperature sensor may have been malfunctioning. Continue this inspection procedure until step 29, and if there are no problems with other parts, replace the engine coolant temperature sensor (refer to step 57).

·

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
OK
NG



OK

17.READ FREEZE FRAME DATA

NG

17.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA

Result:
Freeze Frame Data Item Result Suspected Area Proceed to
EVAP (Purge) VSV At least 1 of the 5 sets of freeze frame data is not 0% Purge VSV A
All 5 sets of freeze frame data are 0% - B


HINT:

If the purge VSV is stuck closed, air fuel ratio compensation by the purge VSV is incorrectly adjusted, and then the air fuel ratio becomes lean and the engine may stall.




A

18.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL)

B

27.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SEED)
18.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A255866C04
2.031,0.625 2.229,0.125 2.229,0.125 2.396,0.125 false 1.729,1.99 1.521,3.177 1.521,3.177 1.656,3.177 false 1.719,3.063 1.885,3.219 0.167,0.156 10 false *1 2.469,0.031 2.635,0.188 0.167,0.156 10 false *2
*1 Purge VSV
*2 Fuel Vapor Feed Hose Assembly
(to Canister)


Disconnect the fuel vapor feed hose assembly (on the canister side) of the purge VSV.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Evap Control.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Evap Control
50004 234 6

f.

When the purge VSV is operated using the GTS, check whether the port of the purge VSV applies suction to your finger.

OK:
GTS Operation Specified Condition
ON Purge VSV port applies suction to finger
OFF Purge VSV port applies no suction to finger


Result:
Result Proceed to
Abnormal A
Normal B


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Even if the results are normal, the purge VSV may have been malfunctioning. Continue this inspection procedure until step 29, and if there are no problems with other parts, replace the purge VSV (refer to step 57).





A

19.INSPECT PURGE VSV

B

27.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SEED)
19.INSPECT PURGE VSV

Result:
Proceed to
OK
NG



OK

20.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)

NG

20.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)
a.

Check the harnesses and connectors, referring to DTC P0443 inspection procedure.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0443


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.



Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

REPAIR POWER SOURCE CIRCUIT (PURGE VSV POWER SOURCE)

21.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Check the harnesses and connectors, referring to DTC P0443 inspection procedure.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0443

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA

Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Calculate Load 110% or higher of the current value of the vehicle*1 Mass air flow meter sub-assembly A
AFS Voltage B1S1 or AFS Voltage B2S1 Less than 3.3 V*2
·

Air fuel ratio sensor

·

Harness and connector

·

Actual air fuel ratio abnormal


B
Both freeze frame data items listed above Values are other than above - C


HINT:
·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.

·

*1: If the mass air flow meter sub-assembly is malfunctioning and incorrectly measures the intake air volume to be higher than the actual volume of air flowing through the intake air surge tank assembly, the freeze frame data will show a high engine load value.

·

*2: As the air fuel ratio sensor output is low before the sensor warms up, the value at that time cannot be used for diagnosis. If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air fuel ratio is rich, the actual air fuel ratio will become lean and the engine may stall.





A

23.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY

B

24.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

C

30.READ FREEZE FRAME DATA
23.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
a.

Remove the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL


b.

Check for foreign matter in the air flow passage of the mass air flow meter sub-assembly.

Result:
Result Proceed to
Visible foreign matter is present A
Visible foreign matter is not present B


HINT:
·

Even if the results are normal, the mass air flow meter sub-assembly may have been malfunctioning. Continue this inspection procedure until step 34, and if there are no problems with other parts, replace the mass air flow meter sub-assembly (refer to step 57).

·

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION





A

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

B

30.READ FREEZE FRAME DATA
24.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
A280723E18
1.313,0.604 1.74,0.833 0.427,0.229 10 false 12.5% 1.271,0.938 1.823,1.188 0.552,0.25 10 false -12.5% 0.615,2.208 1.75,2.417 1.135,0.208 10 false Higher than 3.4 V 0.531,3.781 1.74,3.99 1.208,0.208 10 false Higher than 0.55 V 0.938,2.583 1.719,2.792 0.781,0.208 10 false Below 3.1 V 0.938,4.146 1.75,4.365 0.813,0.219 10 false Below 0.4 V 1.031,0.25 2.115,0.458 1.083,0.208 10 false Injection Volume 0.635,1.771 3.031,1.99 2.396,0.219 10 false Air Fuel Ratio Sensor Output Voltage 0.698,3.313 3.115,3.531 2.417,0.219 10 false Heated Oxygen Sensor Output Voltage

a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / All Data / AFS Voltage B1S1 and AFS Voltage B2S1.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
AFS Voltage B1S1
AFS Voltage B2S1
50004 234 2 35,37

f.

Change the fuel injection volume using the GTS, and monitor the voltage output of the air fuel ratio sensors displayed on the GTS.

Standard:
GTS Display Specified Condition
Control the Injection Volume for A/F Sensor (12.5%) Air fuel ratio sensors output voltage is below 3.1 V
Control the Injection Volume for A/F Sensor (-12.5%) Air fuel ratio sensors output voltage is higher than 3.4 V


Result:
Result Proceed to
Abnormal A
Normal B


HINT:
·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

Even if the results are normal, the air fuel ratio sensor may have been malfunctioning. Continue this inspection procedure until step 34, and if there are no problems with other parts, replace the air fuel ratio sensor (refer to step 57).





A

25.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)

B

30.READ FREEZE FRAME DATA
25.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)
a.

Check the harnesses and connectors, referring to DTC P0031 inspection procedure.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0031

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

26.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

REPAIR POWER SOURCE CIRCUIT (AIR FUEL RATIO SENSOR POWER SOURCE)

26.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Check the harnesses and connectors, referring to DTC P2237 inspection procedure.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P2237

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine > Active Test
GTS Display
Control the Fuel Pump / Speed
50004 234 230

d.

When performing the Active Test, check for an operating sound from the fuel pump.

OK:
Control the Fuel Pump / Speed Specified Condition
ON Operating sound heard
OFF Operating sound not heard


Result:
Result Proceed to
Abnormal A
Normal B


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.

·

If the fuel pump operating noise is abnormal, proceed to step 28.





A

28.INSPECT FUEL PUMP (RESISTANCE)

B

29.CHECK FUEL SYSTEM
28.INSPECT FUEL PUMP (RESISTANCE)
a.

Inspect the fuel pump.

Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL PUMP>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

29.CHECK FUEL SYSTEM
a.

Check for foreign matter such as iron particles around the fuel pump, and for signs that the fuel pump was stuck.

Result:
Result Proceed to
There is foreign matter or signs that fuel pump was stuck A
There is no foreign matter and no signs that fuel pump was stuck B


HINT:

If there is foreign matter such as iron particles on the fuel pump, remove the foreign matter.




A

REPAIR OR REPLACE FUEL SYSTEM

B

57.REPLACE MALFUNCTIONING PARTS
30.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA

Result:
Freeze Frame Data Item Result Proceed to
Initial Engine Coolant Temp, Initial Intake Air Temp Difference in temperature between each item is below 10°C (18°F)*1 A
Difference in temperature between each item is 10°C (18°F) or higher*2 B


HINT:
·

*1: A long time had elapsed after stopping the engine.

·

*2: A long time had not elapsed after stopping the engine.





A

31.READ FREEZE FRAME DATA

B

33.READ FREEZE FRAME DATA
31.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions present when the DTC was stored which are recorded in the freeze frame data.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA

A217929E21
0.229,0.856 3.082,1.519 2.853,0.663 10 Engine Coolant Temperature Increase after Engine Start (Engine Coolant Temperature - Engine Coolant Temperature at Engine Start) 3.423,0.037 3.718,0.235 0.295,0.198 10 (°C) 5.609,2.116 6.223,2.286 0.615,0.17 10 (Minutes) 5.16,1.69 5.317,1.846 0.156,0.156 10 A 4.964,0.779 5.121,0.935 0.156,0.156 10 C 3.891,0.493 4.047,0.649 0.156,0.156 10 B 3.563,2.39 5.574,2.547 2.01,0.156 10 Time Elapsed after Engine Start

Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Initial Engine Coolant Temp, Coolant Temp, Engine Run Time Range A
·

Engine coolant temperature sensor

·

Thermostat


A
Range B Engine coolant temperature sensor B
Range C - C


HINT:

This step is not directly related to engine stall.




A

32.INSPECT THERMOSTAT

B

34.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

C

58.CLEAR DTC
32.INSPECT THERMOSTAT
a.

Inspect the thermostat.

Click hereEngine / Hybrid System>2GR-FE COOLING>THERMOSTAT>INSPECTION

Result:
Result Proceed to
Abnormal A
Normal B


HINT:

This step is not directly related to engine stall.




A

B

34.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
33.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA

Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Coolant Temp 120°C (248°F) or higher Engine coolant temperature sensor A
Engine coolant temperature is lower than outside temperature* by 15°C (27°F) or higher Engine coolant temperature sensor
Freeze frame data item listed above Values are other than above - B


HINT:

*: Use an actual outside temperature estimated from the Initial Intake Air, Ambient Temp for A/C, and (if possible) the weather when the DTC was detected.




A

34.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

58.CLEAR DTC
34.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Result Proceed to
Abnormal A
Normal B


HINT:
·

Even if the results are normal, the engine coolant temperature sensor may have been malfunctioning. If there are no problems with other parts, replace the engine coolant temperature sensor (refer to step 57).

·

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




A

B

57.REPLACE MALFUNCTIONING PARTS
35.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA

Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Total of ISC Learning Value and ISC Feedback Value Less than 80% of the current value of the vehicle*1 Throttle with motor body assembly A
120% or higher of the current value of the vehicle*2 B
From 80 to 120% of the current value of the vehicle - C


HINT:
·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.

·

*1: If the throttle with motor body assembly has a temporary problem in which it cannot fully close, the intake air volume and engine speed increase. As a result, the ISC learning amount becomes less than the standard. At this time, if the throttle with motor body assembly returns to normal and fully closes, the intake air volume will be insufficient and the engine may stall.

·

*2: If carbon accumulates on the throttle with motor body assembly and the intake air volume decreases, the ISC learning amount is increased to maintain the idle speed. If this situation continues, the ISC learning amount reaches the upper limit, the idle speed cannot be maintained causing idling to become unstable, and the engine may stall.





A

36.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY

B

37.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY

C

38.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR)
36.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY
a.

Check for foreign matter and signs that the throttle with motor body assembly was stuck, and also check that the valve and shaft move smoothly during operation.

Result:
Result Proceed to
Abnormal A
Normal B


HINT:
·

Even if the results are normal, the throttle with motor body assembly may have been malfunctioning. Continue this inspection procedure until step 42, and if there are no problems with other parts, replace the throttle with motor body assembly (refer to step 57).

·

Perform "Inspection After Repair" after replacing the throttle with motor body assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION





A

REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

B

38.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR)
37.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY
a.

Check if carbon is in the air flow passage of the throttle with motor body assembly.

Result:
Result Proceed to
Carbon in passage A
No carbon in passage B


HINT:
·

Even if the results are normal, the throttle with motor body assembly may have been malfunctioning. Continue this inspection procedure until step 42, and if there are no problems with other parts, replace the throttle with motor body assembly (refer to step 57).

·

Perform "Inspection After Repair" after replacing the throttle with motor body assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION





A

REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

B

38.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR)
38.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR)
a.

Perform the Active Test, referring to DTC P0011 inspection procedure.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0011

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.

·

If the camshaft timing oil control valve assembly (for intake camshaft) is stuck at the advanced side, the valve overlap increases and combustion worsens due to the internal EGR which may cause rough idle or cause the engine to stall.




Result:
Proceed to
OK
NG



OK

39.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT EXHAUST LINEAR)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

39.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT EXHAUST LINEAR)
a.

Perform the Active Test, referring to DTC P0014 inspection procedure.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0014

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.

·

If the camshaft timing oil control valve assembly (for exhaust camshaft) is stuck at the retard side, the valve overlap increases and combustion worsens due to the internal EGR which may cause rough idle or cause the engine to stall.




Result:
Proceed to
OK
NG



OK

40.READ FREEZE FRAME DATA

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)

40.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA

Result:
Freeze Frame Data Item Suspected Area Proceed to
IGN Advance Knock Correct Learn Value
Differs from the current value of the vehicle by 10 deg or more Below 3 deg(CA)
·

Engine coolant temperature sensor

·

Mass air flow meter sub-assembly

·

Knock control sensor


A
3 deg(CA) or more - B
Differs from the current value of the vehicle by less than 10 deg -


HINT:
·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.

·

Even if the results are normal, the knock control sensors may have been malfunctioning. If there are no problems with other parts, replace the knock control sensors (refer to step 57).





A

41.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

57.REPLACE MALFUNCTIONING PARTS
41.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

42.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (INTAKE AIR TEMPERATURE SENSOR)

NG

42.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (INTAKE AIR TEMPERATURE SENSOR)
a.

Inspect the mass air flow meter sub-assembly (intake air temperature sensor).

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>MASS AIR FLOW METER>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly or knock control sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

43.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
a.

Check the harnesses and connectors, referring to DTC P0300 inspection procedure.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0300

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)




Result:
Proceed to
OK
NG



OK

44.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)

NG

44.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
a.

Check the harnesses and connectors, referring to DTC P0351 inspection procedure.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0351

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)




Result:
Proceed to
OK
NG



OK

45.READ FREEZE FRAME DATA

NG

REPAIR POWER SOURCE CIRCUIT (IGNITION COIL ASSEMBLY POWER SOURCE)

45.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Idle Spark Advn Ctrl (#1 to #6) At least one cylinder shows a value of 4 deg(CA) or higher
·

Fuel injector system

·

Ignition coil system


A
All cylinders show a value of less than 4 deg(CA) - B



A

46.READ VALUE USING GTS (IDLE SPARK ADVN CTRL #)

B

47.READ FREEZE FRAME DATA
46.READ VALUE USING GTS (IDLE SPARK ADVN CTRL #)
a.

Change the location of the ignition coil assembly for the cylinder whose Idle Spark Advn Ctrl (#1 to #6) was 4 deg(CA) or more in step 45.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Using the GTS, select [Idle Spark Advn Ctrl (#1 to #6)] of the Data List.

Powertrain > Engine > Data List
Tester Display
Idle Spark Advn Ctrl #1
Idle Spark Advn Ctrl #2
Idle Spark Advn Ctrl #3
Idle Spark Advn Ctrl #4
Idle Spark Advn Ctrl #5
Idle Spark Advn Ctrl #6
50003 234 506,507,508,509,510,511
Result:
Result Proceed to
Same as result in step 45 A
Different from result in step 45 B


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Perform "Inspection After Repair" after replacing the ignition coil assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION





A

47.READ FREEZE FRAME DATA

B

47.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA

Result:
Freeze Frame Data Item Suspected Area Proceed to
A/C Signal Air Conditioner FB Val Power Steering Signal
A/C Signal display changes from OFF to ON Value displayed for Air Conditioner FB Val increases Does not change from OFF A/C system B
Changes from OFF to ON Power steering system A
A/C Signal display does not change from OFF Value displayed for Air Conditioner FB Val does not increase Changes from OFF to ON
Does not change from OFF -


HINT:
·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.

·

The normal value for the ISC learning amount is engine displacement (liters) x 0.9.

·

Even if the results are normal, the power steering system or the air conditioning system may have been malfunctioning. Continue this inspection procedure until step 49, and if there are no problems with other parts, inspect the power steering system and the air conditioning system (refer to step 57).





A

48.READ FREEZE FRAME DATA

B

48.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA

Result:
Freeze Frame Data Item Suspected Area Proceed to
Electrical Load Signal 1 Electric Load Feedback Val Difference between Engine Speed and SPD (NT) Vehicle Speed
Electrical Load Signal 1 display changes from OFF to ON*1, or value displayed for Electric Load Feedback Val increases*1 Value displayed for Electric Load Feedback Val changes - - Electrical load signal circuit A
Value displayed for Electric Load Feedback Val does not change At least 1 of the 5 sets of freeze frame data is less than 100 rpm Less than 20 km/h (12 mph) A/T system B
Electrical Load Signal 1 display does not change from OFF, or value displayed for Electric Load Feedback Val does not increase - At least 1 of the 5 sets of freeze frame data is less than 100 rpm Less than 20 km/h (12 mph)
At least 1 of the 5 sets of freeze frame data is less than 100 rpm 20 km/h (12 mph) or higher - C
All 5 sets of freeze frame data are 100 rpm or higher -
Electrical Load Signal 1 display changes from OFF to ON*1, or value displayed for Electric Load Feedback Val increases*1 Value displayed for Electric Load Feedback Val does not change At least 1 of the 5 sets of freeze frame data is less than 100 rpm 20 km/h (12 mph) or higher
All 5 sets of freeze frame data are 100 rpm or higher -


HINT:
·

*1: If the Electrical Load Signal 1 display changes from OFF to ON or the Electric Load Feedback Val increases, it probably is a malfunction due to a change in electrical load. Check the generator and the continuity and connections between the generator and ECM.

·

If the vehicle speed is 20 km/h (12 mph) or less and the difference between Engine Speed and SPD (NT) is 100 rpm or less, inspect the automatic transaxle. (Depending on the rate of vehicle deceleration, the engine speed may have decreased due to the A/T lock-up release being late.)

·

The normal value for the ISC learning amount is engine displacement (liters) x 0.9.

·

Even if the results are normal, the electrical load signal system and/or the A/T system may have been malfunctioning. Continue this inspection procedure until step 49, and if there are no problems with other parts, inspect the electrical load system and/or the A/T system (refer to step 57).





A

B

C

49.READ FREEZE FRAME DATA
49.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA

Result:
Freeze Frame Data Item Suspected Area Proceed to
Shift SW Status (P or N Range) Neutral Position SW Signal
P and N position are both OFF in at least one data set ON when Shift SW Status D or R Park/Neutral position switch assembly A
OFF when Shift SW Status D or R A/T system B
All 5 sets of freeze frame data are ON - - C


HINT:

Even if the results are normal, the park/neutral position switch assembly and/or A/T system may have been malfunctioning. If there are no problems with other parts, inspect the park/neutral position switch assembly and/or A/T system (refer to step 57).




A

B

C

57.REPLACE MALFUNCTIONING PARTS
50.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Throttle Sensor Position, Calculate Load Calculate Load decreases while Throttle Sensor Position increases Mass air flow meter sub-assembly A
Calculate Load does not decrease while Throttle Sensor Position increases - B



A

51.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY

B

52.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
51.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
a.

Remove the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL


b.

Check for foreign matter in the air flow passage of the mass air flow meter sub-assembly.

Result:
Result Proceed to
Visible foreign matter is present A
Visible foreign matter is not present B


HINT:
·

Even if the results are normal, the mass air flow meter sub-assembly may have been malfunctioning. Continue this inspection procedure until step 56, and if there are no problems with other parts, replace the mass air flow meter sub-assembly (refer to step 57).

·

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION





A

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

B

52.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
52.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
a.

Check the harnesses and connectors, referring to DTC P0300 inspection procedure.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0300

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)




Result:
Proceed to
OK
NG



OK

53.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)

NG

53.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
a.

Check the harnesses and connectors, referring to DTC P0351 inspection procedure.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0351

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)




Result:
Proceed to
OK
NG



OK

54.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)

NG

REPAIR POWER SOURCE CIRCUIT (IGNITION COIL ASSEMBLY POWER SOURCE)

54.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 230

d.

When performing the Active Test, check for an operating sound from the fuel pump.

OK:
Control the Fuel Pump / Speed Specified Condition
ON Operating sound heard
OFF Operating sound not heard


Result:
Result Proceed to
Abnormal A
Normal B


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.

·

If the fuel pump operating noise is abnormal, proceed to step 56





A

55.INSPECT FUEL PUMP

B

56.CHECK FUEL SYSTEM
55.INSPECT FUEL PUMP
a.

Inspect the fuel pump.

Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL PUMP>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

56.CHECK FUEL SYSTEM
a.

Check for foreign matter such as iron particles around the fuel pump, and for signs that the fuel pump was stuck.

Result:
Result Proceed to
There is foreign matter or signs that fuel pump was stuck A
There is no foreign matter and no signs that fuel pump was stuck B


HINT:

If there is foreign matter such as iron particles on the fuel pump, remove the foreign matter.




A

REPAIR OR REPLACE FUEL SYSTEM

B

57.REPLACE MALFUNCTIONING PARTS
57.REPLACE MALFUNCTIONING PARTS
a.

If the malfunction could not be identified in steps 3 to 29, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.

Performed Step Inspection or Part to Replace
Step 6 Brake booster assembly replacement
Step 8 Mass air flow meter sub-assembly replacement
Step 9 Air fuel ratio sensor replacement
Step 16 Engine coolant temperature sensor replacement
Step 18 Purge VSV replacement
Step 29 Fuel pump replacement


b.

If the malfunction could not be identified in steps 22 to 26, 30 to 34 replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.

Performed Step Inspection or Part to Replace
Step 23 Mass air flow meter sub-assembly replacement
Step 24 Air fuel ratio sensor replacement
Step 34 Engine coolant temperature sensor replacement


c.

If the malfunction could not be identified in steps 35 to 42, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.

Performed Step Inspection or Part to Replace
Step 36, 37 Throttle with motor body assembly replacement
Step 40 Knock control sensor replacement


d.

If the malfunction could not be identified in steps 43 to 49, inspect and repair the part which is suspected to be malfunctioning according to the step where an inspection was performed.

Performed Step Inspection or Part to Replace
Step 47 A/C system inspection and repair
Power steering system inspection and repair
Step 48 Electrical load system inspection and repair
A/T system inspection and repair
Step 49 Park/Neutral position switch assembly inspection and repair
A/T system inspection and repair


e.

If the malfunction could not be identified in steps 50 to 56, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.

Performed Step Inspection or Part to Replace
Step 51 Mass air flow meter sub-assembly replacement

HINT:
·

Referring to the chart, inspect and repair or replace the part from the step where an inspection was performed.

·

Perform "Inspection After Repair" after replacing or servicing parts related to engine operation. Refer to detailed information in Initialization.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

58.CLEAR DTC
58.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Clear the DTCs.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

59.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
59.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check if engine stall symptoms are present.

HINT:

If any engine stall symptoms are present, recheck for DTCs and freeze frame data and perform an inspection.



Result:
Proceed to
OK
NG



OK

END

NG

REPAIR MALFUNCTIONING PARTS