Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER(When Using the Engine Support Bridge for LHD)
RM2030EQ _53 Suspension _014647 FRONT SUSPENSION _0281053 FRONT SUSPENSION MEMBER(When Using the Engine Support Bridge for LHD) A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER(When Using the Engine Support Bridge for LHD)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL HOLE PLUG

a.

Install 5 hole plugs to the front frame assembly.


Hide 52217E 2.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH

a.
C239310C01
0.147,0.134 0.325,0.287 0.178,0.152 10 *a 0.42,0.526 0.598,0.678 0.178,0.152 10 *A 0.402,2.588 0.581,2.741 0.178,0.152 10 *B 0.317,0.447 2.927,2.411 2.61,1.964 0.317,2.509 2.927,4.474 2.61,1.964
*A Type A
*B Type B
*a View from Underneath
V100135

Front of the Vehicle


Temporarily install a new front suspension member body mounting rear cushion LH while confirming the installation direction.

NOTICE:

Position the front suspension member body mounting rear cushion LH in the correct direction.



b.
C169232C03
1.188,1.5 1.406,1.5 1.406,1.5 1.521,2.125 false 2.479,0.854 2.01,0.854 false 2.198,2.698 2.5,2.698 false 1.01,1.427 1.188,1.625 0.177,0.198 10 false *1 2.521,0.781 2.854,0.979 0.333,0.198 10 false SST 2.531,2.625 2.906,2.875 0.375,0.25 10 false SST
*1 Front Suspension Member Body Mounting Rear Cushion LH


Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)


c.
C167152C01
1.635,1.5 2.052,1.5 false 0.531,2.24 0.979,2.323 false 2.396,0.875 2.281,0.875 2.281,0.875 2.219,0.792 false 0.969,3.167 0.833,3.167 0.833,3.167 0.75,3.073 false 2.427,0.813 2.719,1.115 0.292,0.302 10 false *a 2.104,1.406 2.542,1.688 0.438,0.281 10 false SST 1,3.083 1.354,3.344 0.354,0.26 10 false *b 0.25,2.146 0.708,2.469 0.458,0.323 10 false SST
*a Hold
*b Turn


Using SST, install the front suspension member body mounting rear cushion LH as shown in the illustration.

NOTICE:

Check that there is no clearance between the front frame assembly and the front suspension member body mounting rear cushion LH.



Hide 52215 3.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION RH

a.
C239311C01
0.145,0.135 0.31,0.292 0.165,0.157 10 *a 0.346,0.563 0.533,0.725 0.188,0.162 10 *A 0.358,2.619 0.546,2.782 0.188,0.162 10 *B 0.275,0.49 2.9,2.473 2.625,1.983 0.275,2.536 2.9,4.518 2.625,1.983
*A Type A
*B Type B
*a View from Underneath
V100135

Front of the Vehicle


Temporarily install a new front suspension member body mounting rear cushion RH while confirming the installation direction.

NOTICE:

Position the front suspension member body mounting rear cushion RH in the correct direction.



b.

Install SST using the same procedure as the front suspension member body mounting rear cushion LH.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)


c.

Using SST, install the front suspension member body mounting rear cushion RH.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

HINT:

Perform the same procedure as the LH side.



Hide 52211J 4.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION

a.
C238988C04
0.157,0.121 0.31,0.274 0.152,0.152 10 *a
*a View from Underneath
V100135

Front of the Vehicle


Temporarily install a new front suspension member body mounting front cushion while confirming the installation direction.

NOTICE:

Position the front suspension member body mounting front cushion in the correct direction.



b.

Install SST using the same procedure as the front suspension member body mounting rear cushion LH.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)


c.
C167148C02
2.271,0.74 2.479,0.74 false 1.646,1.354 2.125,1.198 false 0.771,2.292 0.969,2.406 false 1.042,3.021 1.25,3.073 false 2.5,0.646 2.688,0.802 0.188,0.156 10 *a 1.26,3 1.604,3.177 0.344,0.177 10 *b 0.49,2.208 0.802,2.375 0.313,0.167 10 SST 2.167,1.104 2.479,1.271 0.313,0.167 10 SST
*a Hold
*b Turn


Using SST, install the front suspension member body mounting front cushion as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

Check that there is no clearance between the front frame assembly and the front suspension member body mounting front cushion.



Hide 52216B 5.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER

a.

Install the 2 front suspension member body mounting rear stoppers to the front frame assembly.


Hide 52213A 6.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER

a.

Install the 2 front suspension member body mounting front stoppers to the front frame assembly.


Hide 51227B 7.INSTALL FRONT SUSPENSION MEMBER DYNAMIC DAMPER

a.

Install the front suspension member dynamic damper to the front frame assembly with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 48069 8.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 9.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.


Hide 10.INSTALL STEERING LINK ASSEMBLY

Hide 11.INSTALL FRONT STABILIZER BAR WITH FRONT STABILIZER LINK ASSEMBLY

a.

Install the front stabilizer bar with 2 front stabilizer link assemblies to the front frame assembly.


Hide 48829A 12.INSTALL FRONT NO. 1 STABILIZER BRACKET LH

Hide 48824A 13.INSTALL FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Perform the same procedure as the LH side.


Hide 51100G 14.INSTALL FRONT FRAME ASSEMBLY

a.

Slowly jack up the front frame assembly with an engine lifter using 4 attachments or equivalent tools.

CAUTION:
·

The front frame assembly is a heavy component. Make sure that it is supported securely.

·

Make sure to secure the front frame assembly to prevent it from dropping.



NOTICE:

Use the attachments to keep the front frame assembly level.



b.
A255441E02
0.198,1.24 0.313,1.385 0.115,0.146 10 false A 3.083,1.26 3.198,1.406 0.115,0.146 10 false A 1.094,0.219 1.208,0.365 0.115,0.146 10 true B 0.115,0.052 0.229,0.198 0.115,0.146 10 false B 2.292,0.25 2.406,0.396 0.115,0.146 10 true B 3.24,0.042 3.354,0.188 0.115,0.146 10 false B 1.208,2.698 1.333,2.844 0.125,0.146 10 true C 2.146,2.688 2.271,2.833 0.125,0.146 10 true C 0.271,2.354 0.396,2.5 0.125,0.146 10 true D 0.979,3.073 1.104,3.219 0.125,0.146 10 true D 2.354,3.021 2.479,3.167 0.125,0.146 10 true D 3.021,2.323 3.146,2.469 0.125,0.146 10 true D

Install the frame side rail plates RH and LH with the 4 bolts and 2 nuts.

Torque:
A : 85 N*m (867 kgf*cm, 63 ft.*lbf)
B : 32 N*m (326 kgf*cm, 24 ft.*lbf)


c.

Install the front suspension member rear braces RH and LH with the 4 bolts and 2 nuts.

Torque:
C : 85 N*m (867 kgf*cm, 63 ft.*lbf)
D : 32 N*m (326 kgf*cm, 24 ft.*lbf)


d.

Connect the 2 clamps.


Hide 15.REMOVE BELT

a.

Remove SST from the vehicle body.

C313710N01
3.885,1.833 5.969,1.833 true 3.042,1.854 0.958,1.854 true 6.021,1.75 6.688,2.094 0.667,0.344 10 false SST 0.635,1.781 1.302,2.125 0.667,0.344 10 false SST


b.

Connect the windshield washer jar assembly to the vehicle body and tighten the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Install the bolt and nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 16.REMOVE ENGINE SUPPORT BRIDGE

a.

Remove SST from the vehicle body.

NOTICE:

Prevent SST from contacting the vehicle body or windshield.



b.

Install the 2 hood support assemblies.

Click hereVehicle Exterior>DOOR / HATCH>HOOD SUPPORT>INSTALLATION


c.

Connect the pressure sensor assembly connector.


Hide 17.REMOVE ENGINE HANGERS

a.

Remove the 4 bolts and No. 1 and No. 2 engine hangers from the engine assembly.


Hide 88710E 18.CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

Hide 88704 19.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.

Engage the clamp and connect the suction hose sub-assembly to the vehicle body.


b.

Remove the vinyl tape from the suction hose sub-assembly.


c.

Sufficiently apply compressor oil to a new O-ring and fitting surface of the suction hose sub-assembly.

Compressor Oil:

ND-OIL 8 or equivalent



d.

Install the O-ring to the suction hose sub-assembly.


e.

Connect the suction hose sub-assembly.


f.
E255283

Rotate the hook connector as shown in the illustration.


g.

Insert the pipe joint to the fitting hole securely and tighten the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 16571C 20.CONNECT NO. 1 RADIATOR HOSE

Hide 12360 21.INSTALL FRONT ENGINE MOUNTING INSULATOR ASSEMBLY

a.

Install the front engine mounting insulator assembly to the front frame assembly with the 3 nuts.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


Hide 12372A 22.INSTALL ENGINE MOUNTING INSULATOR LH

a.

Install the engine mounting insulator LH to the front frame assembly with the 3 nuts.

Torque:
87 N*m (887 kgf*cm, 64 ft.*lbf)


b.

Install the 2 hole plugs.


Hide 12362 23.INSTALL ENGINE MOUNTING INSULATOR RH

a.

Install the engine mounting insulator RH to the front frame assembly with the 3 nuts.

Torque:
87 N*m (887 kgf*cm, 64 ft.*lbf)


b.

Install the 2 hole plugs.


Hide 45220 24.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 43420 25.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

Hide 43410 26.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48069 27.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 28.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45470 29.CONNECT TIE ROD ASSEMBLY LH

Hide 45460 30.CONNECT TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48810 31.INSTALL FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 32.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 43502H 33.INSTALL FRONT AXLE SHAFT NUT LH

Hide 43501H 34.INSTALL FRONT AXLE SHAFT NUT RH

HINT:

Perform the same procedure as for the LH side.


Hide 17410 35.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 17584B 36.INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Front Side)

Hide 17190 39.INSTALL INTAKE AIR SURGE TANK ASSEMBLY

Hide 17805F 40.INSTALL INTAKE AIR RESONATOR SUB-ASSEMBLY

Hide 17751 41.INSTALL INLET NO. 1 AIR CLEANER

Hide 17701 43.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17801 44.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17735 45.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 17752 46.INSTALL INLET NO. 2 AIR CLEANER

Hide 55702A 48.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 49.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 50.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

a.

Connect the negative (-) cable to the negative (-) battery terminal.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 52.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 55.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR

Hide 57.INSPECT FOR EXHAUST GAS LEAK

Hide 53295E 58.INSTALL COOL AIR INTAKE DUCT SEAL

Hide 53737B 59.INSTALL FRONT FENDER APRON SEAL LH

Hide 53736 60.INSTALL FRONT FENDER APRON SEAL RH

Hide 51442C 61.INSTALL ENGINE UNDER COVER LH

Hide 51441C 62.INSTALL ENGINE UNDER COVER RH

Hide 11209 63.INSTALL V-BANK COVER SUB-ASSEMBLY

Hide 64.INSTALL FRONT WHEELS

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)

Hide 65.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT