Home › Engine / Hybrid System › A25A-FXS (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2017.12–2018.08
RM33C0E _51 Engine / Hybrid System _065420 A25A-FXS ENGINE MECHANICAL _0324467 ENGINE ASSEMBLY A

A25A-FXS ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:
·

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



PROCEDURE

Hide 12306 1.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly LH is necessary.


a.
A406679N02
2.604,1.219 2.76,1.417 0.156,0.198 10 true A 0.802,0.906 0.958,1.104 0.156,0.198 10 true B 1.677,0.073 1.833,0.271 0.156,0.198 10 true C

Install the engine mounting insulator sub-assembly LH with the 2 bolts and nut.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Temporarily tighten the bolt (A), and then fully tighten the 2 bolts and nut in the order of (B), (A) and (C).



Hide 12341 2.INSTALL ENGINE MOUNTING SPACER

HINT:

Perform this procedure only when replacement of the engine mounting spacer is necessary.


a.
A402194N01
1.438,1.865 1.594,2.063 0.156,0.198 10 true A 2.604,0.719 2.76,0.917 0.156,0.198 10 true B

Install the engine mounting spacer to the vehicle body with the 2 bolts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Temporarily tighten the bolt (A), and then fully tighten the 2 bolts in the order of (B) and (A).



Hide 12305 3.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A406677C01
0.75,1.438 0.906,1.635 0.156,0.198 10 true A 2.448,0.875 2.604,1.073 0.156,0.198 10 true B 1.792,0.031 1.969,0.198 0.177,0.167 10 true C

Install the engine mounting insulator sub-assembly RH with the 2 bolts and nut.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Temporarily tighten the bolt (A), and then fully tighten the 2 bolts and nut in the order of (B), (A) and (C).



b.

Connect the cooler bracket to the engine mounting insulator sub-assembly RH with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


c.

Engage the clamp.


d.

Install the radiator reserve tank assembly with the bolt and nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


e.

Engage the No. 6 water by-pass hose.


Hide 5.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND

a.

Remove the engine assembly from the engine stand.


Hide 19315 6.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 31270 8.INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY

Hide 30900 9.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY

Hide 11363A 10.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 821H2 12.INSTALL HV AIR CONDITIONING WIRE

a.

Engage the guide to install the HV air conditioning wire to the hybrid vehicle transaxle assembly.


b.

Install the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.
A407268C02
1.313,0.552 1.583,0.26 1.583,0.26 1.708,0.26 true 1.771,0.188 2.083,0.385 0.313,0.198 10 false *a
*a Green-colored Lock
V100137

Slide


Connect the connector and slide the green-colored lock as shown in the illustration to lock it securely.

CAUTION:

Make sure to wear insulated gloves.


NOTICE:

Make sure that the connector is connected securely.



d.

Engage the 2 clamps.


Hide 12371A 13.INSTALL REAR ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


a.
A408373C02
0.813,1.604 0.813,1.323 false 2.188,1.802 2.188,1.521 false 1.083,1.073 1.083,0.615 1.083,0.615 1.24,0.615 false 1.281,1.5 1.281,1.219 false 2.542,1.76 2.542,1.125 false 0.75,1.646 1.063,1.844 0.313,0.198 10 false *1 2.094,1.844 2.406,2.042 0.313,0.198 10 false *2 1.219,1.5 1.531,1.698 0.313,0.198 10 false *a 1.302,0.531 1.615,0.729 0.313,0.198 10 false *b 2.479,1.802 2.792,2 0.313,0.198 10 false *b
*1 Rear Engine Mounting Bracket
*2 Rear Engine Mounting Insulator
*a Protrusion
*b Hole


Align the hole of the rear engine mounting insulator with the protrusion of the rear engine mounting bracket, slide the rear engine mounting insulator onto the rear engine mounting bracket to align the holes and install the rear engine mounting insulator with the bolt.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 12361A 14.INSTALL FRONT ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.


Click hereDrivetrain>P710 (HYBRID TRANSMISSION / TRANSAXLE)>HYBRID VEHICLE TRANSAXLE>INSTALLATION

Hide 51100G 15.INSTALL FRONT FRAME ASSEMBLY

Hide 82121 16.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine assembly.


Hide 45319 17.INSTALL STEERING GEAR HEAT INSULATOR (for LHD)

Hide 11361J 18.INSTALL FLYWHEEL HOUSING UNDER COVER

a.

Install the flywheel housing under cover to the cylinder block sub-assembly.


Hide 19.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

HINT:

Perform inspection after repair after replacing the engine assembly.

w/ Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION

w/o Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION


a.

Set the engine assembly with transaxle on an engine lifter.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




b.

Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly and engine mounting bracket RH.


c.

Install the fuel delivery guard to the engine mounting bracket RH with the bolt.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


d.

Operate the engine lifter and install the engine assembly with transaxle to the vehicle.

CAUTION:

Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.




e.
A406667C04
1.333,2.094 1.49,2.292 0.156,0.198 10 true A 1.208,2.781 1.365,2.979 0.156,0.198 10 true C 2,2.094 2.156,2.292 0.156,0.198 10 true A 2.125,2.781 2.281,2.979 0.156,0.198 10 true C 0.833,0.396 0.99,0.594 0.156,0.198 10 true B 2.438,0.354 2.594,0.552 0.156,0.198 10 true B 0.719,3.896 0.875,4.094 0.156,0.198 10 true E 2.615,3.906 2.771,4.104 0.156,0.198 10 true E 2.563,4.438 2.719,4.635 0.156,0.198 10 true D 0.75,4.417 0.906,4.615 0.156,0.198 10 true D 1.323,2.448 1.479,2.646 0.156,0.198 10 true A 2.01,2.427 2.167,2.625 0.156,0.198 10 true A
V100135

Bolt
V100136

Nut


Install the front bumper extension sub-assembly RH and front bumper extension sub-assembly LH to the front frame assembly and vehicle body with the 8 bolts.

Torque:
Bolt (A) : 9.0 N*m (92 kgf*cm, 80 in.*lbf)
Bolt (B) : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
Bolt (C) : 135 N*m (1377 kgf*cm, 100 ft.*lbf)


f.

Install the front suspension member bracket sub-assembly RH and front suspension member bracket sub-assembly LH to the front frame assembly and vehicle body with the 4 bolts and 2 nuts.

Torque:
Bolt (D) : 17.5 N*m (178 kgf*cm, 13 ft.*lbf)
Bolt (E) : 135 N*m (1377 kgf*cm, 100 ft.*lbf)
Nut : 17.5 N*m (178 kgf*cm, 13 ft.*lbf)


g.
A406669N02
1.24,0.125 1.396,0.323 0.156,0.198 10 true A 0.885,0.677 1.042,0.875 0.156,0.198 10 true B 0.854,1.135 1.01,1.333 0.156,0.198 10 true C 1.01,1.698 1.167,1.896 0.156,0.198 10 true D

Install the engine mounting insulator sub-assembly LH to the hybrid vehicle transaxle assembly with the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:

Fully tighten the 4 bolts in the order of (A), (C), (B) and (D).



h.
A406668N03
1.125,0.094 1.281,0.292 0.156,0.198 10 true A 1.646,1.958 1.802,2.156 0.156,0.198 10 true B 2.531,0.51 2.688,0.708 0.156,0.198 10 true C

Install the engine mounting stay LH to the engine mounting insulator LH with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Temporarily tighten the bolt (A), and then fully tighten the 3 bolts in the order of (B), (C) and (A).



i.

Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 3 bolts and nut.

Torque:
Bolt : 72 N*m (734 kgf*cm, 53 ft.*lbf)
Nut : 42 N*m (428 kgf*cm, 31 ft.*lbf)


j.

Install the body mounting plate with the 6 bolts.

Torque:
17.5 N*m (178 kgf*cm, 13 ft.*lbf)


Hide 17410 21.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 45220 22.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 16281F 23.CONNECT NO. 5 WATER BY-PASS HOSE

a.

Connect the No. 5 water by-pass hose to the No. 3 water by-pass pipe and slide the clip to secure it.


Hide 24.CONNECT WIRE HARNESS

a.

Engage the earth wire to the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Engage the claw to connect the wire harness to the engine room relay block and junction block assembly.


c.

Connect the 5 connectors to the engine room relay block and junction block assembly.


d.

Install the nut to the engine room relay block and junction block assembly.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Install the No. 2 relay block cover to the engine room relay block and junction block assembly.


Hide G9229A 25.CONNECT NO. 5 INVERTER COOLING HOSE

a.

Connect the No. 5 inverter cooling hose to the motor cooling cooler and slide the clip to secure it.


Hide 88704 26.CONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 88711 27.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE SUB-ASSEMBLY

Hide 16572D 28.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the water inlet and slide the clip to secure it.


Hide 16571C 29.CONNECT NO. 1 RADIATOR HOSE (w/ Canister Pump Module)

a.

Connect the No. 1 radiator hose to the front engine mounting bracket with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


b.

Connect the No. 1 radiator hose to the water outlet and slide the clip to secure it.


Hide 16571C 30.CONNECT NO. 1 RADIATOR HOSE (w/o Canister Pump Module)

a.

Connect the No. 1 radiator hose to the water outlet and slide the clip to secure it.


Hide 89422 31.INSTALL NO. 2 ENGINE COOLANT TEMPERATURE SENSOR (w/ Canister Pump Module)

Hide 23901 32.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly.

i.

Connect the fuel tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION



b.

Install the No. 1 fuel pipe clamp to the fuel tube connector.


Hide 87245 33.CONNECT INLET HEATER HOSE

a.
A403462C02
1.01,0.979 1.438,0.979 false 1.875,0.969 2.302,0.969 false 1.021,1.354 1.448,1.354 false 1.844,1.365 2.281,1.917 2.281,1.917 2.594,1.917 false 0.813,0.885 1.125,1.042 0.313,0.156 10 false *a 0.833,1.271 1.146,1.427 0.313,0.156 10 false *b 2.365,0.896 2.677,1.052 0.313,0.156 10 false *a 2.635,1.844 2.948,2 0.313,0.156 10 false *b
*a Protrusion
*b Cutout


Align the protrusions of the inlet heater hose connector with the cutouts in the flow shutting valve (water by-pass hose assembly) and push them together until the inlet heater hose connector makes a "click" sound.


b.
A406310C03
1.573,1.156 1.844,0.594 1.844,0.594 2.052,0.594 false 2.094,0.531 2.375,0.729 0.281,0.198 10 true *a
*a Retainer
V100135

Push
V100136

Push in


Push in the retainer.


c.

Check that the flow shutting valve (water by-pass hose assembly) and inlet heater hose connector are securely connected by pulling on them.


Hide 87246 34.CONNECT OUTLET HEATER HOSE

a.
A403463C02
1.052,1.156 1.573,1.156 false 0.99,0.365 1.219,0.365 1.219,0.365 1.521,0.792 false 0.875,1.063 1.188,1.219 0.313,0.156 10 false *a 0.823,0.281 1.135,0.438 0.313,0.156 10 false *b
*a Protrusion
*b Cutout


Align the protrusion of the No. 2 water by-pass pipe sub-assembly with the cutout in the outlet heater hose connector and push them together until the outlet heater hose makes a "click" sound.


b.
A406311C03
1.302,1.552 1.521,1.552 1.521,1.552 1.813,1.271 false 1.125,1.479 1.375,1.688 0.25,0.208 10 true *a
*a Retainer
V100135

Push
V100136

Push in


Push in the retainer.


c.

Check that the No. 2 water by-pass pipe sub-assembly and outlet heater hose connector are securely connected by pulling on them.


Hide 23826 35.CONNECT NO. 1 FUEL VAPOR FEED HOSE

a.

Connect the No. 1 fuel vapor feed hose to the No. 1 vacuum switching valve assembly and slide the clip to secure it.


Hide G92A0A 36.INSTALL INVERTER RESERVE TANK ASSEMBLY

a.
A407618C03
0.51,3.021 0.677,3.021 0.677,3.021 0.948,2.948 true 1.469,3 1.792,2.885 1.792,2.885 1.979,2.885 true 1.104,0.563 1.417,0.563 false 1.219,0.854 1.531,0.854 false 0.25,2.938 0.49,3.135 0.24,0.198 10 true *1 2.021,2.802 2.26,3 0.24,0.198 10 true *2 1.5,0.49 1.74,0.688 0.24,0.198 10 true *a 1.594,0.792 1.833,0.99 0.24,0.198 10 true *b
*1 No. 5 Inverter Cooling Hose
*2 No. 2 Inverter Cooling Hose
*a Pin
*b Grommet


Connect the No. 2 inverter cooling hose to the inverter reserve tank assembly and slide the clip to secure it.


b.

Connect the No. 5 inverter cooling hose to the inverter reserve tank assembly and slide the clip to secure it.


c.

Fit the pin of the inverter reserve tank assembly into grommet as shown in the illustration.


d.

Install the inverter reserve tank assembly with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide G9200 37.INSTALL INVERTER WITH CONVERTER ASSEMBLY

Hide 52618 38.INSTALL FRONT LOWER BUMPER ABSORBER

a.

Engage the 2 claws to install the front lower bumper absorber.


b.

Install the 4 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 53737B 40.INSTALL FRONT FENDER APRON SEAL LH

a.

Install the front fender apron seal LH with the 2 screws and clip.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 53736 41.INSTALL FRONT FENDER APRON SEAL RH

a.

Install the front fender apron seal RH with the 2 screws and clip.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 42.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY (w/ Cover)

a.

Install the No. 2 engine under cover assembly with the 4 screws and 6 clips.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 51441 43.INSTALL NO. 1 ENGINE UNDER COVER

a.

Install the No. 1 engine under cover with the bolt, 6 screws and 2 clips.

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 53852K 44.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

a.

Install the front wheel opening extension pad LH with the 3 screws.


Hide 53851M 45.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH

a.

Install the front wheel opening extension pad RH with the 3 screws.


Hide 12601B 46.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

a.
A409241

Engage the 3 clips to install the No. 1 engine cover sub-assembly.

NOTICE:
·

Securely engage the clips.

·

If the clips are forcibly engaged or struck with an object, they may be damaged.




Hide 49.ADD ENGINE COOLANT (for Engine)

Hide 50.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 54.INSPECT FOR ENGINE OIL LEAK

Hide 55.INSPECT FOR COOLANT LEAK (for Engine)

Hide 61.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR

Hide 62.INSTALL FRONT WHEELS

Hide 63. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 64.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT