The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
12306
1.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY LH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly LH is necessary.
Install the engine mounting insulator sub-assembly LH with the 2 bolts and nut.
Temporarily tighten the bolt (A), and then fully tighten the 2 bolts and nut in the order of (B), (A) and (C).
12341
2.INSTALL ENGINE MOUNTING SPACER
Perform this procedure only when replacement of the engine mounting spacer is necessary.
Install the engine mounting spacer to the vehicle body with the 2 bolts.
Temporarily tighten the bolt (A), and then fully tighten the 2 bolts in the order of (B) and (A).
12305
3.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.
Install the engine mounting insulator sub-assembly RH with the 2 bolts and nut.
Temporarily tighten the bolt (A), and then fully tighten the 2 bolts and nut in the order of (B), (A) and (C).
Connect the cooler bracket to the engine mounting insulator sub-assembly RH with the bolt.
Engage the clamp.
Install the radiator reserve tank assembly with the bolt and nut in the order shown in the illustration.
Engage the No. 6 water by-pass hose.
4.INSTALL ENGINE HANGERS
5.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND
Remove the engine assembly from the engine stand.
19315
6.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE
13405
7.INSTALL FLYWHEEL SUB-ASSEMBLY
31270
8.INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY
30900
9.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY
11363A
10.INSTALL FLYWHEEL HOUSING SIDE COVER
28193
11.INSTALL STARTER HOLE INSULATOR
821H2
12.INSTALL HV AIR CONDITIONING WIRE
Engage the guide to install the HV air conditioning wire to the hybrid vehicle transaxle assembly.
Install the bolt.
| *a | Green-colored Lock |
|
Slide |
Connect the connector and slide the green-colored lock as shown in the illustration to lock it securely.
Make sure to wear insulated gloves.
Make sure that the connector is connected securely.
Engage the 2 clamps.
12371A
13.INSTALL REAR ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the rear engine mounting insulator is necessary.
| *1 | Rear Engine Mounting Bracket |
| *2 | Rear Engine Mounting Insulator |
| *a | Protrusion |
| *b | Hole |
Align the hole of the rear engine mounting insulator with the protrusion of the rear engine mounting bracket, slide the rear engine mounting insulator onto the rear engine mounting bracket to align the holes and install the rear engine mounting insulator with the bolt.
12361A
14.INSTALL FRONT ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the front engine mounting insulator is necessary.
Click hereDrivetrain>P710 (HYBRID TRANSMISSION / TRANSAXLE)>HYBRID VEHICLE TRANSAXLE>INSTALLATION
51100G
15.INSTALL FRONT FRAME ASSEMBLY
82121
16.INSTALL ENGINE WIRE
Install the engine wire to the engine assembly.
45319
17.INSTALL STEERING GEAR HEAT INSULATOR (for LHD)
11361J
18.INSTALL FLYWHEEL HOUSING UNDER COVER
Install the flywheel housing under cover to the cylinder block sub-assembly.
19.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
Perform inspection after repair after replacing the engine assembly.
w/ Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION
w/o Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION
Set the engine assembly with transaxle on an engine lifter.
Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly and engine mounting bracket RH.
Install the fuel delivery guard to the engine mounting bracket RH with the bolt.
Operate the engine lifter and install the engine assembly with transaxle to the vehicle.
Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.
Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.
|
Bolt |
|
Nut |
Install the front bumper extension sub-assembly RH and front bumper extension sub-assembly LH to the front frame assembly and vehicle body with the 8 bolts.
Install the front suspension member bracket sub-assembly RH and front suspension member bracket sub-assembly LH to the front frame assembly and vehicle body with the 4 bolts and 2 nuts.
Install the engine mounting insulator sub-assembly LH to the hybrid vehicle transaxle assembly with the 4 bolts.
Fully tighten the 4 bolts in the order of (A), (C), (B) and (D).
Install the engine mounting stay LH to the engine mounting insulator sub-assembly LH with the 3 bolts.
Temporarily tighten the bolt (A), and then fully tighten the 3 bolts in the order of (B), (C) and (A).
Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 3 bolts and nut.
Install the body mounting plate with the 6 bolts.
20.INSTALL FRONT DRIVE SHAFT ASSEMBLY
17410
21.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)
45220
22.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY
16281F
23.CONNECT NO. 5 WATER BY-PASS HOSE
Connect the No. 5 water by-pass hose to the No. 3 water by-pass pipe and slide the clip to secure it.
24.CONNECT WIRE HARNESS
Engage the earth wire to the 2 bolts.
Engage the claw to connect the wire harness to the engine room relay block and junction block assembly.
Connect the 5 connectors to the engine room relay block and junction block assembly.
Install the nut to the engine room relay block and junction block assembly.
Install the No. 2 relay block cover to the engine room relay block and junction block assembly.
G9229A
25.CONNECT NO. 5 INVERTER COOLING HOSE
Connect the No. 5 inverter cooling hose to the motor cooling cooler and slide the clip to secure it.
88704
26.CONNECT SUCTION HOSE SUB-ASSEMBLY
88711
27.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE SUB-ASSEMBLY
16572D
28.CONNECT NO. 2 RADIATOR HOSE
Connect the No. 2 radiator hose to the water inlet and slide the clip to secure it.
16571C
29.CONNECT NO. 1 RADIATOR HOSE (w/ Canister Pump Module)
Connect the No. 1 radiator hose to the front engine mounting bracket with the bolt.
Connect the No. 1 radiator hose to the water outlet and slide the clip to secure it.
16571C
30.CONNECT NO. 1 RADIATOR HOSE (w/o Canister Pump Module)
Connect the No. 1 radiator hose to the water outlet and slide the clip to secure it.
89422
31.INSTALL NO. 2 ENGINE COOLANT TEMPERATURE SENSOR (w/ Canister Pump Module)
23901
32.CONNECT FUEL TUBE SUB-ASSEMBLY
Connect the fuel tube sub-assembly.
Connect the fuel tube sub-assembly to the fuel pipe.
Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION
Install the No. 1 fuel pipe clamp to the fuel tube connector.
87245
33.CONNECT INLET HEATER HOSE
| *a | Protrusion |
| *b | Cutout |
Align the protrusions of the inlet heater hose connector with the cutouts in the flow shutting valve (water by-pass hose assembly) and push them together until the inlet heater hose connector makes a "click" sound.
| *a | Retainer |
|
Push |
|
Push in |
Push in the retainer.
Check that the flow shutting valve (water by-pass hose assembly) and inlet heater hose connector are securely connected by pulling on them.
87246
34.CONNECT OUTLET HEATER HOSE
| *a | Protrusion |
| *b | Cutout |
Align the protrusion of the No. 2 water by-pass pipe sub-assembly with the cutout in the outlet heater hose connector and push them together until the outlet heater hose makes a "click" sound.
| *a | Retainer |
|
Push |
|
Push in |
Push in the retainer.
Check that the No. 2 water by-pass pipe sub-assembly and outlet heater hose connector are securely connected by pulling on them.
23826
35.CONNECT NO. 1 FUEL VAPOR FEED HOSE
Connect the No. 1 fuel vapor feed hose to the No. 1 vacuum switching valve assembly and slide the clip to secure it.
G92A0A
36.INSTALL INVERTER RESERVE TANK ASSEMBLY
| *1 | No. 5 Inverter Cooling Hose |
| *2 | No. 2 Inverter Cooling Hose |
| *a | Pin |
| *b | Grommet |
Connect the No. 2 inverter cooling hose to the inverter reserve tank assembly and slide the clip to secure it.
Connect the No. 5 inverter cooling hose to the inverter reserve tank assembly and slide the clip to secure it.
Fit the pin of the inverter reserve tank assembly into grommet as shown in the illustration.
Install the inverter reserve tank assembly with the bolt.
G9200
37.INSTALL INVERTER WITH CONVERTER ASSEMBLY
52618
38.INSTALL FRONT LOWER BUMPER ABSORBER
Engage the 2 claws to install the front lower bumper absorber.
Install the 4 bolts.
39.INSTALL HEADLIGHT ASSEMBLY
for LED Type Turn Signal Light:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>INSTALLATION
for Bulb Type Turn Signal Light:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>INSTALLATION
53737B
40.INSTALL FRONT FENDER APRON SEAL LH
Install the front fender apron seal LH with the 2 screws and clip.
53736
41.INSTALL FRONT FENDER APRON SEAL RH
Install the front fender apron seal RH with the 2 screws and clip.
42.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY (w/ Cover)
Install the No. 2 engine under cover assembly with the 4 screws and 6 clips.
51441
43.INSTALL NO. 1 ENGINE UNDER COVER
Install the No. 1 engine under cover with the bolt, 6 screws and 2 clips.
53852K
44.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH
Install the front wheel opening extension pad LH with the 3 screws.
53851M
45.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH
Install the front wheel opening extension pad RH with the 3 screws.
12601B
46.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY
Engage the 3 clips to install the No. 1 engine cover sub-assembly.
Securely engage the clips.
If the clips are forcibly engaged or struck with an object, they may be damaged.
47.ADD ENGINE OIL
48.ADD HYBRID TRANSAXLE FLUID
49.ADD ENGINE COOLANT (for Engine)
50.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
for HFC-134a (R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT>REPLACEMENT
for HFO-1234yf (1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT
51.WARM UP COMPRESSOR
for HFC-134a (R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT>REPLACEMENT
for HFO-1234yf (R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT
52.INSPECT SHIFT LEVER POSITION
53.ADJUST SHIFT LEVER POSITION
54.INSPECT FOR ENGINE OIL LEAK
55.INSPECT FOR COOLANT LEAK (for Engine)
56.INSPECT FOR REFRIGERANT LEAK
for HFC-134a (R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT>REPLACEMENT
for HFO-1234yf (R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT
57.INSPECT FOR FUEL LEAK
58.INSPECT FOR EXHAUST GAS LEAK
59.CHECK ENGINE OIL LEVEL
60.INSPECT HYBRID TRANSAXLE FLUID
61.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR
62.INSTALL FRONT WHEELS
63. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
64.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
65.PERFORM INITIALIZATION
66.INSPECT IGNITION TIMING
67.INSPECT ENGINE IDLE SPEED
68.INSPECT CO/HC
69.CHECK SPEED SENSOR SIGNAL