1.DISCHARGE FUEL SYSTEM PRESSURE
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
53292A
3.REMOVE UPPER RADIATOR SUPPORT SEAL
4.REMOVE FRONT WHEEL RH
51441
5.REMOVE NO. 1 ENGINE UNDER COVER
53701
6.REMOVE FRONT FENDER APRON RH
7.DRAIN ENGINE COOLANT
8.DRAIN ENGINE OIL
9.REMOVE COWL TOP OUTER PANEL WITH WINDSHIELD WIPER MOTOR AND LINK
Remove the cowl top outer panel with windshield wiper motor and link (See page Vehicle Interior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION).
17705
10.REMOVE AIR CLEANER CAP
22210
11.REMOVE THROTTLE BODY
23250
12.REMOVE FUEL DELIVERY PIPE WITH INJECTOR ASSEMBLY
Remove the fuel delivery pipe with injector assembly (See page Engine / Hybrid System>2AZ-FE FUEL>FUEL INJECTOR>REMOVAL).
17111
13.REMOVE INTAKE MANIFOLD
Remove the intake manifold (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>KNOCK SENSOR>REMOVAL).
Do not forcibly pull out the intake manifold, as the gap between the body and engine is narrow. Make sure not to scratch the contact surfaces of the intake manifold port to cylinder head.
When replacing the intake manifold, remove the engine assembly (See page Engine / Hybrid System>2AZ-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL).
17135A
14.REMOVE INTAKE MANIFOLD INSULATOR
87245A
15.DISCONNECT HEATER WATER INLET HOSE
Disconnect the heater water inlet hose.
| *A | for Automatic Transaxle
for CVT (w/ Air Cooled Transmission Oil Cooler) |
| *B | for CVT (w/o Air Cooled Transmission Oil Cooler) |
16.DISCONNECT ENGINE WIRE
17410
17.REMOVE FRONT EXHAUST PIPE
15301
18.REMOVE ENGINE OIL LEVEL DIPSTICK
11452
19.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
Remove the bolt and guide.
Remove the O-ring from the guide.
17118
20.REMOVE MANIFOLD STAY
Remove the bolt, nut and stay.
17139
21.REMOVE NO. 2 MANIFOLD STAY
Remove the bolt, nut and stay.
17167
22.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
Remove the 4 bolts and heat insulator.
25051
23.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
Remove the 5 nuts, manifold converter and gasket.
16571C
24.DISCONNECT NO. 1 RADIATOR HOSE
Disconnect the hose from the cylinder head.
51217A
25.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT RH
16361A
26.REMOVE FAN AND GENERATOR V BELT
16603B
27.REMOVE IDLER PULLEY BRACKET
27020
28.REMOVE GENERATOR ASSEMBLY
16470
29.REMOVE RADIATOR RESERVOIR ASSEMBLY
16611
30.REMOVE RADIATOR RESERVOIR BRACKET
12305
31.REMOVE ENGINE MOUNTING INSULATOR RH
19500
32.REMOVE IGNITION COIL ASSEMBLY
11201
33.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
16620
34.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
11301K
35.REMOVE CRANKSHAFT POSITION SENSOR
12101
36.REMOVE OIL PAN SUB-ASSEMBLY
37.SET NO. 1 CYLINDER TO TDC/COMPRESSION
Turn the crankshaft pulley until its groove and the timing mark "0" of the timing chain cover are aligned.
Check that each timing mark of the camshaft timing gear and sprocket is aligned with each timing mark located on the No. 1 and No. 2 bearing caps as shown in the illustration.
If not, turn the crankshaft by 1 revolution (360°) to align the timing marks as above.
13512
38.REMOVE NO. 2 CAMSHAFT
Place paint marks on the chain in alignment with the timing marks on the camshaft timing gear and camshaft timing sprocket.
Remove the 2 nuts, tensioner and gasket.
While holding the camshaft with a wrench, loosen the camshaft timing set bolt.
Using several steps, uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.
Remove the 5 bearing caps.
While holding the No. 2 camshaft by hand, remove the camshaft timing sprocket set bolt.
Remove the camshaft timing sprocket from the No. 2 camshaft with the timing chain wrapped on the sprocket.
Remove the camshaft timing sprocket from the timing chain.
13511
39.REMOVE CAMSHAFT
Using several steps, uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.
Remove the 5 bearing caps.
Remove the camshaft and camshaft timing gear while holding the timing chain by hand.
Tie the timing chain with a string as shown in the illustration.
Be careful not to drop anything inside the timing chain cover.
13471
40.REMOVE CRANKSHAFT PULLEY
12315A
41.REMOVE ENGINE MOUNTING BRACKET RH
11302
42.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
19315
43.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
13566B
44.REMOVE TIMING CHAIN GUIDE
13559
45.REMOVE CHAIN TENSIONER SLIPPER
13561
46.REMOVE NO. 1 CHAIN VIBRATION DAMPER
13506
47.REMOVE CHAIN SUB-ASSEMBLY
11101J
48.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
13050
49.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY
Clamp the camshaft in a vise, and make sure that the camshaft timing gear does not rotate.
Cover all the oil ports with vinyl tape except the advance side port shown in the illustration.
Apply air pressure of 100 kPa (1.0 kgf/cm2, 14 psi) to the oil path, then turn the camshaft timing gear in the advance direction (counterclockwise) by hand.
Cover the paths with a shop rag to avoid oil splashes.
Depending on the air pressure, the camshaft timing gear will turn to the advance angle side without applying force by hand. Also, under the condition that the pressure is difficult to apply because of air leakage from the port, the lock pin may be difficult to release.
Remove the flange bolt of the camshaft timing gear.
Be sure not to remove the other 4 bolts.
When reusing the camshaft timing gear, release the straight lock pin first, then install the gear.
11101
50.REMOVE CYLINDER HEAD SUB-ASSEMBLY
Using several steps, uniformly loosen and remove the 10 cylinder head bolts and 10 plate washers with a 10 mm bi-hexagon wrench in the sequence shown in the illustration.
Head warpage or cracking could result from removing the bolts in the wrong order.
Using a screwdriver, pry between the cylinder head and cylinder block, and remove the cylinder head.
Be careful not to damage the contact surfaces of the cylinder head and cylinder block.
11115
51.REMOVE CYLINDER HEAD GASKET