Home › Drivetrain › K112 (CVT) › TRANSMISSION CONTROL CABLE(for LHD) › from 2016.05
RM24M0E _52 Drivetrain _059572 K112 CVT _0292059 TRANSMISSION CONTROL CABLE(for LHD) A

K112 CVT  TRANSMISSION CONTROL CABLE(for LHD)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

NOTICE:

Before installing the transmission control cable assembly, check that the park/neutral position switch and shift lever are in neutral.


a.

Put the transmission control cable into the cabin and connect the transmission control cable with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Connect the transmission control cable clamp with the 2 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


c.

Install the transmission control cable assembly to the bracket with a new clip.


d.

Install the transmission control cable assembly to the control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


e.

Connect the transmission control cable to the control cable clamp bracket.


f.

Turn the nut of the transmission control cable 180° counterclockwise. While holding the nut in place, push in the stopper until it clicks twice.

C200365E22
1.219,0.635 1.313,0.396 1.313,0.396 1.438,0.396 false 1.021,1.24 0.927,1.479 0.927,1.479 0.802,1.479 false 1.458,0.313 1.635,0.5 0.177,0.188 10 false *1 0.646,1.396 0.844,1.573 0.198,0.177 10 false *2 3.333,0.25 3.5,0.417 0.167,0.167 10 false *a

Text in Illustration
*1 Stopper *2 Nut
*a Push in - -


g.

Install the outer part of the transmission control cable to the shift lever retainer. Check that the spring is positioned at "A" and push in the stopper.

C200366E09
1.115,0.365 1.177,0.167 1.177,0.167 1.302,0.167 false 1.115,0.854 1.031,1.083 1.031,1.083 0.917,1.083 true 1.042,1.323 0.99,1.458 0.99,1.458 0.865,1.458 false 3.5,0.75 3.271,1.396 3.271,1.396 3.156,1.396 true 5.917,0.771 5.688,1.417 5.688,1.417 5.573,1.417 true 3.51,0.698 3.677,0.219 3.677,0.219 3.802,0.219 true 5.938,0.688 6.115,0.198 6.115,0.198 6.229,0.198 true 1.344,0.094 1.573,0.302 0.229,0.208 10 false *1 0.75,1 0.927,1.177 0.177,0.177 10 false *2 0.708,1.385 0.885,1.563 0.177,0.177 10 false *3 3.833,0.135 4.021,0.323 0.188,0.188 10 false *4 6.25,0.115 6.438,0.302 0.188,0.188 10 false *4 3.021,1.313 3.167,1.49 0.146,0.177 10 false A 5.448,1.333 5.594,1.51 0.146,0.177 10 false A

Text in Illustration
*1 Stopper *2 Nut
*3 Shift Lever Retainer *4 Spring

HINT:

If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.



h.
C367599E01
1.813,3.76 2.406,3.135 2.406,3.135 1.74,2.333 false 0.115,0.083 0.354,0.313 0.24,0.229 10 false *a 1.188,0.167 1.427,0.396 0.24,0.229 10 false *c 0.458,1.583 0.698,1.813 0.24,0.229 10 false *b 2.458,3.052 2.698,3.281 0.24,0.229 10 false *1 2.073,0.188 2.313,0.417 0.24,0.229 10 false *c 1.635,1.583 1.875,1.813 0.24,0.229 10 false *c 1.646,2.604 1.885,2.833 0.24,0.229 10 false *c

Push the 2 claws together at the top of the transmission control cable lock piece. While holding the 2 claws together, push the 2 lugs on the bottom of the lock piece toward each other and upward to pull out the lock piece.

Text in Illustration
*1 Lock Piece
*a Side View
*b Bottom View
*c Push


i.
C264711E01
0.254,1.799 0.428,1.962 0.174,0.163 10 *1 0.448,1.888 1.414,1.636 false

Connect the end of the cable to the shift lever assembly.

NOTICE:
·

Make sure that the lock piece is pulled up.

·

Push the end of the cable all the way to the base of the pin.



Text in Illustration
*1 Lock Piece


j.
C264712E02
1.094,1.542 0.5,1.542 true 1.563,1.604 2.292,1.208 2.292,1.208 2.542,1.208 true 0.333,1.458 0.563,1.646 0.229,0.188 10 false *2 2.563,1.115 2.792,1.302 0.229,0.188 10 false *1 1.969,1.594 2.198,1.781 0.229,0.188 10 false *a

Push the lock piece into the adjuster case.

Text in Illustration
*1 Lock Piece
*2 Adjuster Case
*a Push in

NOTICE:

Securely push in the lock piece until it locks.



Hide 55434B 2.INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER

Hide 58533C 3.INSTALL FLOOR CARPET COVER CENTER RH

Hide 58534E 4.INSTALL FLOOR CARPET COVER CENTER LH

Hide 55432B 5.INSTALL INSTRUMENT PANEL FINISH PANEL LOWER (w/ Knee Airbag)

Hide 55432B 6.INSTALL INSTRUMENT PANEL FINISH PANEL LOWER (w/o Knee Airbag)

Hide 55606 7.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 62111C 8.INSTALL COWL SIDE TRIM BOARD RH

Hide 67913B 9.INSTALL FRONT DOOR SCUFF PLATE RH

Hide 55474B 11.INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55607 12.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 62112 13.INSTALL COWL SIDE TRIM BOARD LH

Hide 67914B 14.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 55550 15.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 55041B 16.INSTALL NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY

Hide 55660 17.INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

Hide 55042B 18.INSTALL NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY

Hide 55650 19.INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

Hide 20.INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)

Hide 55414A 21.INSTALL INSTRUMENT CLUSTER FINISH PANEL END (w/o Navigation System)

Hide 55420A 22.INSTALL INSTRUMENT CLUSTER FINISH PANEL CENTER ASSEMBLY

Hide 23.INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE

Hide 17752 31.INSTALL NO. 2 AIR CLEANER INLET

Hide 17751 32.INSTALL NO. 1 AIR CLEANER INLET

Hide 17700 33.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17705 34.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 55712 36.INSTALL FRONT COWL TOP OUTSIDE PANEL WITH WINDSHIELD WIPER MOTOR AND LINK