Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model) › 2020.02–2020.11
RM37A0E _57 Power Source / Network _086883 NETWORKING _0416014 CAN COMMUNICATION SYSTEM(for HV Model) U

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  TERMINALS OF ECU  


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>SYSTEM DIAGRAM

·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



NO. 1 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 1 global CAN junction connector.

i.

Connection diagram

C427139C01
1.74,0.823 2.177,1.083 0.438,0.26 0.188,0.146 0.5,0.344 0.313,0.198 10 false *a 1.833,0.865 2.188,1.083 0.354,0.219 10 false A77
*a Front view of wire harness connector
(to No. 1 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 1 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
A77-1 (CANH) G No. 2 skid control ECU (brake actuator assembly)
(for Bus 2)
A77-12 (CANL) W
A77-2 (CANH) R No. 1 skid control ECU (brake booster with master cylinder assembly)
(for Bus 2)
A77-13 (CANL) W
A77-6 (CANH) SB Central gateway ECU (network gateway ECU)
(for Bus 2)
A77-17 (CANL) W
A77-8 (CANH) L Hybrid vehicle control ECU
(for Bus 2)
A77-19 (CANL) W
A77-9 (CANH) B ECM
(for Bus 2)
A77-20 (CANL) W
A77-10 (CANH) LG Inverter with converter assembly*
(for Bus 2)
A77-21 (CANL) W
A77-11 (CANH) V Inverter with converter assembly
(for Bus 2)
A77-22 (CANL) W

*: for 4WD/AWD





NO. 2 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 2 global CAN junction connector.

i.

Connection diagram

C426295C01
0.896,0.823 1.292,1.083 0.396,0.26 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 0.958,0.854 1.271,1.052 0.313,0.198 10 false H90
*a Front view of wire harness connector
(to No. 2 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 2 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
H90-2 (CANH) G Rack and pinion power steering gear assembly
(for Bus 4)
H90-12 (CANL) W
H90-3 (CANH) L No. 1 skid control ECU (brake booster with master cylinder assembly)
(for Bus 4)
H90-13 (CANL) W
H90-4 (CANH) P ECM
(for Bus 4)
H90-14 (CANL) W
H90-5 (CANH) BE Hybrid vehicle control ECU
(for Bus 4)
H90-15 (CANL) W
H90-6 (CANH) SB No. 8 global CAN junction connector
(for Bus 4)
H90-16 (CANL) W
H90-7 (CANH) V Steering sensor
(for Bus 4)
H90-17 (CANL) W
H90-8 (CANH) R Airbag sensor assembly
(for Bus 4)
H90-18 (CANL) W
H90-9 (CANH) P Tire pressure warning ECU and receiver
(for Bus 4)
H90-19 (CANL) W




NO. 3 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 3 global CAN junction connector.

i.

Connection diagram

C426295C02
0.896,0.823 1.292,1.083 0.396,0.26 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 0.969,0.865 1.281,1.063 0.313,0.198 10 false H91
*a Front view of wire harness connector
(to No. 3 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 3 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
H91-2 (CANH) LG Central gateway ECU (network gateway ECU)
(for Bus 5)
H91-12 (CANL) W
H91-3 (CANH) G Certification ECU (smart key ECU assembly)
(for Bus 5)
H91-13 (CANL) W
H91-4 (CANH) SB Air conditioning amplifier assembly
(for Bus 5)
H91-14 (CANL) W
H91-5 (CANH) P Outer mirror control ECU assembly RH*
(for Bus 5)
H91-15 (CANL) W
H91-6 (CANH) B No. 4 global CAN junction connector
(for Bus 5)
H91-16 (CANL) W

*: w/ Seat Position Memory System





NO. 4 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 4 global CAN junction connector.

i.

Connection diagram

C426294C01
2.031,0.823 2.458,1.073 0.427,0.25 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 2.115,0.865 2.427,1.063 0.313,0.198 10 false H92
*a Front view of wire harness connector
(to No. 4 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 4 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
H92-1 (CANH) BE Main body ECU (multiplex network body ECU)
(for Bus 5)
H92-7 (CANL) W
H92-2 (CANH) LG Meter mirror sub-assembly*1
(for Bus 5)
H92-8 (CANL) W
H92-3 (CANH) B No. 3 global CAN junction connector
(for Bus 5)
H92-9 (CANL) W
H92-4 (CANH) R No. 9 global CAN junction connector
(for Bus 5)
H92-10 (CANL) W
H92-5 (CANH) P Outer mirror control ECU assembly LH*2
(for Bus 5)
H92-11 (CANL) W

·

*1: w/ Headup Display System

·

*2: w/ Seat Position Memory System





NO. 5 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 5 global CAN junction connector.

i.

Connection diagram

C426295C03
0.896,0.823 1.292,1.083 0.396,0.26 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 0.958,0.854 1.271,1.052 0.313,0.198 10 false H94
*a Front view of wire harness connector
(to No. 5 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 5 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
H94-1 (CANH) P Central gateway ECU (network gateway ECU)
(for Bus 1)
H94-11 (CANL) W
H94-2 (CANH) R Millimeter wave radar sensor assembly*1
(for Bus 1)
H94-12 (CANL) W
H94-3 (CANH) L Forward recognition camera*1
(for Bus 1)
H94-13 (CANL) W
H94-4 (CANH) B No. 10 global CAN junction connector
(for Bus 1)
H94-14 (CANL) W
H94-5 (CANH) L Clearance warning ECU assembly*2
(for Bus 1)
H94-15 (CANL) W
H94-6 (CANH) GR Parking assist ECU*3
(for Bus 1)
H94-16 (CANL) W

·

*1: w/ Toyota Safety Sense

·

*2: w/ TOYOTA Parking Assist-sensor System

·

*3: w/ Panoramic View Monitor System





NO. 6 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 6 global CAN junction connector.

i.

Connection diagram

C427139C15
1.74,0.823 2.177,1.083 0.438,0.26 0.188,0.146 0.5,0.344 0.313,0.198 10 false *a 1.833,0.865 2.188,1.083 0.354,0.219 10 false H95
*a Front view of wire harness connector
(to No. 6 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 6 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
H95-2 (CANH) B Central gateway ECU (network gateway ECU)
(for Bus 3)
H95-13 (CANL) W
H95-3 (CANH) G Central gateway ECU (network gateway ECU)
(for Bus 3)
H95-14 (CANL) W
H95-4 (CANH) B Radio and display receiver assembly
(for Bus 3)
H95-15 (CANL) W




NO. 8 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 8 global CAN junction connector.

i.

Connection diagram

C426294C02
2.031,0.823 2.458,1.073 0.427,0.25 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 2.104,0.865 2.417,1.063 0.313,0.198 10 false M33
*a Front view of wire harness connector
(to No. 8 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 8 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
M33-2 (CANH) LG No. 2 skid control ECU (brake actuator assembly)
(for Bus 4)
M33-8 (CANL) W
M33-3 (CANH) G Central gateway ECU (network gateway ECU)
(for Bus 4)
M33-9 (CANL) W
M33-4 (CANH) SB No. 2 global CAN junction connector
(for Bus 4)
M33-10 (CANL) W
M33-6 (CANH) R Yaw rate sensor
(for Bus 4)
M33-12 (CANL) W




NO. 9 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 9 global CAN junction connector.

i.

Connection diagram

C426294C03
2.031,0.823 2.458,1.073 0.427,0.25 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 2.115,0.865 2.427,1.063 0.313,0.198 10 false M96
*a Front view of wire harness connector
(to No. 9 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 9 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
M96-1 (CANH) LG Multiplex network door ECU*1
(for Bus 5)
M96-7 (CANL) W
M96-2 (CANH) G Position control ECU assembly LH*2
(for Bus 5)
M96-8 (CANL) W
M96-3 (CANH) R No. 4 global CAN junction connector
(for Bus 5)
M96-9 (CANL) W
M96-4 (CANH) B Combination meter assembly
(for Bus 5)
M96-10 (CANL) W

·

*1: w/ Power Back Door System

·

*2: w/ Seat Position Memory System





NO. 10 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 10 global CAN junction connector.

i.

Connection diagram

C426294C04
2.031,0.823 2.458,1.073 0.427,0.25 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 2.125,0.865 2.479,1.104 0.354,0.24 10 false M97
*a Front view of wire harness connector
(to No. 10 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 10 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
M97-3 (CANH) V Blind spot monitor sensor LH*1
(for Bus 1)
M97-9 (CANL) W
M97-4 (CANH) B No. 1 CAN junction terminal
(for Bus 1)
M97-10 (CANL) W
M97-5 (CANH) R Rear television camera assembly*2
(for Bus 1)
M97-11 (CANL) W
M97-6 (CANH) B No. 5 global CAN junction connector
(for Bus 1)
M97-12 (CANL) W

·

*1: w/ Blind Spot Monitor System

·

*2: w/ Panoramic View Monitor System





NO. 1 CAN JUNCTION TERMINAL


a.

Check the No. 1 CAN junction terminal.

i.

Connection diagram

C285687C86
2.156,0.719 2.646,0.958 0.49,0.24 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 2.26,0.76 2.875,0.958 0.615,0.198 10 false M89
*a Front view of wire harness connector
(to No. 1 CAN Junction Terminal)
- -



ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction terminal.

Terminal No. (Symbol) Wiring Color Connected to
M89-3 (CANH) B No. 10 global CAN junction connector
(for Bus 1)
M89-2 (CANL) W




DLC3


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

C427140C01
1.531,0.76 1.927,1.052 0.396,0.292 0.104,0.115 0.417,0.313 0.313,0.198 10 false *1 1.604,0.823 2.021,1.125 0.417,0.302 10 false H56
*1 DLC3 - -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H56-6 (CANH) - H56-14 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H56-6 (CANH) - H56-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H56-14 (CANL) - H56-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H56-6 (CANH) - H56-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H56-14 (CANL) - H56-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)


C427141C01
1.167,0.781 1.635,1.031 0.469,0.25 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 1.292,0.823 1.708,1.073 0.417,0.25 10 false H59
*a Component without harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H59 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

C427142C01
1.24,0.854 1.646,1.115 0.406,0.26 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 1.333,0.896 1.729,1.135 0.396,0.24 10 false H59
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Diagnosis Bus Branch Lines (DLC3 - Central gateway ECU (network gateway ECU))
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H59-14 (CA6H) - H59-5 (CA6L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher
H59-14 (CA6H) - H59-10 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H59-5 (CA6L) - H59-10 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H59-14 (CA6H) - H59-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H59-5 (CA6L) - H59-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 1 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H59-23 (CA1H) - H59-8 (CA1L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
H59-23 (CA1H) - H59-10 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H59-8 (CA1L) - H59-10 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H59-23 (CA1H) - H59-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H59-8 (CA1L) - H59-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 2 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H59-18 (CA4H) - H59-17 (CA4L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
H59-18 (CA4H) - H59-10 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H59-17 (CA4L) - H59-10 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H59-18 (CA4H) - H59-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H59-17 (CA4L) - H59-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 3 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H59-6 (CA3H) - H59-19 (CAYH) HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
H59-21 (CA3L) - H59-20 (CAYL) LOW-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
H59-6 (CA3H) - H59-10 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H59-21 (CA3L) - H59-10 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H59-6 (CA3H) - H59-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H59-21 (CA3L) - H59-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 4 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H59-22 (CA2H) - H59-7 (CA2L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
H59-22 (CA2H) - H59-10 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H59-7 (CA2L) - H59-10 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H59-22 (CA2H) - H59-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H59-7 (CA2L) - H59-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 5 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H59-15 (CA5H) - H59-16 (CA5L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
H59-15 (CA5H) - H59-10 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H59-16 (CA5L) - H59-10 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H59-15 (CA5H) - H59-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H59-16 (CA5L) - H59-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




STEERING SENSOR


C427526C01
2.313,1.448 2.719,1.667 0.406,0.219 4.844,1.292 5.25,1.51 0.406,0.219 0.26,0.135 0.573,0.333 0.313,0.198 10 false *a 2.448,1.479 2.76,1.677 0.313,0.198 10 false z5 4.917,1.313 5.229,1.51 0.313,0.198 10 false H57
*a Component without harness connected
(Steering Sensor)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H57 steering sensor connector.


c.
C427527C01
0.552,0.927 0.958,1.229 0.406,0.302 0.146,0.156 0.458,0.354 0.313,0.198 10 false *a 0.625,0.99 0.938,1.188 0.313,0.198 10 false H57
*a Front view of wire harness connector
(to Steering Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H57-3 (CANH) - H57-8 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H57-3 (CANH) - H57-6 (ESS) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H57-8 (CANL) - H57-6 (ESS) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H57-3 (CANH) - H57-4 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H57-8 (CANL) - H57-4 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




YAW RATE SENSOR


C427528C01
3.396,0.135 3.781,0.375 0.385,0.24 0.188,0.146 0.5,0.344 0.313,0.198 10 false *a 3.51,0.177 3.823,0.375 0.313,0.198 10 false M1
*a Component without harness connected
(Yaw Rate Sensor)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the M1 yaw rate sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C427523C02
0.719,0.792 1.094,1.01 0.375,0.219 3.625,0.792 4,1.01 0.375,0.219 0.688,0.219 1,0.417 0.313,0.198 10 false *a 3.771,0.167 4.083,0.365 0.313,0.198 10 false *1 0.823,0.823 1.135,1.021 0.313,0.198 10 false M1 3.688,0.823 4,1.021 0.313,0.198 10 false H56
*1 DLC3 - -
*a Front view of wire harness connector
(to Yaw Rate Sensor)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
M1-3 (CANH) - M1-2 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
M1-3 (CANH) - M1-1 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M1-2 (CANL) - M1-1 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M1-3 (CANH) - H56-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
M1-2 (CANL) - H56-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




HYBRID VEHICLE CONTROL ECU


Refer to Terminals of ECU.


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A32 and H67 hybrid vehicle control ECU connectors.


c.

Measure the resistance according to the value(s) in the table below.

C331621C06
0.302,0.656 0.719,0.906 0.417,0.25 3.615,0.635 4.031,0.885 0.417,0.25 0.094,0.052 0.406,0.25 0.313,0.198 10 false *a 0.396,0.688 0.854,0.885 0.458,0.198 10 false A32 3.708,0.677 4.167,0.875 0.458,0.198 10 false H67
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
- -


Standard Resistance:
Bus 2 Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A32-21 (CA1H) - A32-8 (CA1L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A32-21 (CA1H) - H67-3 (E1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A32-8 (CA1L) - H67-3 (E1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A32-21 (CA1H) - H67-27 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A32-8 (CA1L) - H67-27 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 4 Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A32-7 (CA3P) - A32-20 (CA3N) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A32-7 (CA3P) - H67-3 (E1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A32-20 (CA3N) - H67-3 (E1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A32-7 (CA3P) - H67-27 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A32-20 (CA3N) - H67-27 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




INVERTER WITH CONVERTER ASSEMBLY


Refer to Terminals of ECU.


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A55 inverter with converter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C427143C04
0.313,0.792 0.74,1.031 0.427,0.24 3.292,0.802 3.719,1.042 0.427,0.24 3.531,0.146 3.844,0.344 0.313,0.198 10 false *1 0.406,0.125 0.719,0.323 0.313,0.198 10 false *a 0.406,0.823 0.719,1.021 0.313,0.198 10 false A55 3.365,0.833 3.677,1.031 0.313,0.198 10 false H56
*1 DLC3 - -
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A55-22 (CANH) - A55-31 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A55-22 (CANH) - A55-9 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A55-31 (CANL) - A55-9 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A55-22 (CANH) - H56-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A55-31 (CANL) - H56-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

for 4WD/AWD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A55-24 (CNH2) - A55-33 (CNL2) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A55-24 (CNH2) - A55-9 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A55-33 (CNL2) - A55-9 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A55-24 (CNH2) - H56-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A55-33 (CNL2) - H56-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




ECM


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A27 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

C427529C01
1.802,0.771 2.188,1.031 0.385,0.26 0.479,0.083 0.792,0.281 0.313,0.198 10 false *a 1.875,0.813 2.188,1.01 0.313,0.198 10 false A27
*a Front view of wire harness connector
(to ECM)
- -


Standard Resistance:
Bus 2 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A27-8 (CANH) - A27-18 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A27-8 (CANH) - A27-10 (E1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A27-18 (CANL) - A27-10 (E1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A27-8 (CANH) - A27-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A27-18 (CANL) - A27-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 4 Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A27-7 (CAN+) - A27-17 (CAN-) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A27-7 (CAN+) - A27-10 (E1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A27-17 (CAN-) - A27-10 (E1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A27-7 (CAN+) - A27-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A27-17 (CAN-) - A27-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




COMBINATION METER ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H21 combination meter assembly connector.


c.
C427530C01
1.479,0.188 1.917,0.458 0.438,0.271 0.167,0.146 0.479,0.344 0.313,0.198 10 false *a 1.583,0.25 1.99,0.5 0.406,0.25 10 false H21
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H21-32 (CANH) - H21-31 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
H21-32 (CANH) - H21-21 (ES) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H21-31 (CANL) - H21-21 (ES) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H21-32 (CANH) - H21-40 (B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H21-31 (CANL) - H21-40 (B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




NO. 1 SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)


Refer to Terminals of ECU.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A44 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


c.
C427531C01
1.5,0.125 1.885,0.365 0.385,0.24 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 1.573,0.167 1.885,0.365 0.313,0.198 10 false A44
*a Front view of wire harness connector
(to No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 2 Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A44-35 (CA2H) - A44-36 (CA2L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A44-35 (CA2H) - A44-28 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A44-36 (CA2L) - A44-28 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A44-35 (CA2H) - A44-14 (+BI1) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A44-36 (CA2L) - A44-14 (+BI1) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 4 Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A44-38 (CA1H) - A44-39 (CA1L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A44-38 (CA1H) - A44-28 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A44-39 (CA1L) - A44-28 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A44-38 (CA1H) - A44-14 (+BI1) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A44-39 (CA1L) - A44-14 (+BI1) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)


Refer to Terminals of ECU.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


c.
C427532C01
1.448,0.26 1.865,0.49 0.417,0.229 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.542,0.292 1.854,0.49 0.313,0.198 10 false A57
*a Front view of wire harness connector
(to No. 2 Skid Control ECU (Brake Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 2 Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A57-16 (CA2H) - A57-17 (CA2L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A57-16 (CA2H) - A57-1 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A57-17 (CA2L) - A57-1 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A57-16 (CA2H) - A57-14 (+BS) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A57-17 (CA2L) - A57-14 (+BS) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 4 Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A57-27 (CANH) - A57-43 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A57-27 (CANH) - A57-1 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A57-43 (CANL) - A57-1 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A57-27 (CANH) - A57-14 (+BS) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A57-43 (CANL) - A57-14 (+BS) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


Refer to Terminals of ECU.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H43 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

C427524C02
0.354,0.792 0.729,1.01 0.375,0.219 3.625,0.792 4,1.01 0.375,0.219 0.198,0.104 0.51,0.302 0.313,0.198 10 false *a 3.771,0.167 4.083,0.365 0.313,0.198 10 false *1 0.406,0.823 0.719,1.021 0.313,0.198 10 false H43 3.688,0.823 4,1.021 0.313,0.198 10 false H56
*1 DLC3 - -
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H43-5 (CANH) - H43-4 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H43-5 (CANH) - H56-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H43-4 (CANL) - H56-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H43-5 (CANH) - H56-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H43-4 (CANL) - H56-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


Refer to Terminals of ECU.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H48 certification ECU (smart key ECU assembly) connector.


c.
C427533C01
0.104,0.969 0.521,1.25 0.417,0.281 0.115,0.063 0.427,0.26 0.313,0.198 10 false *a 0.198,1.021 0.51,1.219 0.313,0.198 10 false H48
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H48-1 (CANH) - H48-2 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H48-1 (CANH) - H48-18 (E) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H48-2 (CANL) - H48-18 (E) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H48-1 (CANH) - H48-4 (+B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H48-2 (CANL) - H48-4 (+B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




RACK AND PINION POWER STEERING GEAR ASSEMBLY


Refer to Terminals of ECU.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the C67 rack and pinion power steering gear assembly connector.


c.
C427525C01
0.198,1.01 0.552,1.271 0.354,0.26 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 0.25,1.063 0.563,1.26 0.313,0.198 10 false C67
*a Front view of wire harness connector
(to Rack and Pinion Power Steering Gear Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
C67-10 (CANH) - C67-11 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
C67-10 (CANH) - C67-7 (PGND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
C67-11 (CANL) - C67-7 (PGND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
C67-10 (CANH) - C67-8 (PIG) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
C67-11 (CANL) - C67-8 (PIG) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIRBAG SENSOR ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H58 airbag sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C427534C01
0.792,0.781 1.177,1.042 0.385,0.26 3.594,0.771 3.979,1.031 0.385,0.26 0.385,0.208 0.698,0.406 0.313,0.198 10 false *a 3.406,0.208 3.719,0.406 0.313,0.198 10 false *1 3.667,0.813 3.979,1.01 0.313,0.198 10 false H56 0.865,0.823 1.177,1.021 0.313,0.198 10 false H58
*1 DLC3 - -
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H58-26 (CANH) - H58-27 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
H58-26 (CANH) - H58-33 (E1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H58-27 (CANL) - H58-33 (E1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H58-26 (CANH) - H56-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H58-27 (CANL) - H56-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for HV Model)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H62 air conditioning amplifier assembly connector.


c.
C427751C01
0.073,0.906 0.448,1.188 0.375,0.281 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.146,0.958 0.458,1.156 0.313,0.198 10 false H62
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H62-2 (CANH) - H62-1 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H62-2 (CANH) - H62-17 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H62-1 (CANL) - H62-17 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H62-2 (CANH) - H62-5 (B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H62-1 (CANL) - H62-5 (B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




RADIO AND DISPLAY RECEIVER ASSEMBLY


Refer to Terminals of ECU.


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H2 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C427752C01
3.729,0.76 4.135,1.031 0.406,0.271 0.229,0.781 0.635,1.052 0.406,0.271 0.385,0.188 0.698,0.385 0.313,0.198 10 false *a 3.729,0.156 4.042,0.354 0.313,0.198 10 false *1 3.813,0.823 4.125,1.021 0.313,0.198 10 false H56 0.354,0.823 0.667,1.021 0.313,0.198 10 false H2
*1 DLC3 - -
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H2-13 (CANH) - H2-14 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H2-13 (CANH) - H56-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H2-14 (CANL) - H56-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H2-13 (CANH) - H56-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H2-14 (CANL) - H56-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the M43 blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

C427753C01
0.594,0.792 1.042,1.01 0.448,0.219 3.625,0.865 4.073,1.083 0.448,0.219 0.708,0.188 1.021,0.385 0.313,0.198 10 false *a 3.542,0.198 3.854,0.396 0.313,0.198 10 false *1 0.698,0.823 1.01,1.021 0.313,0.198 10 false M43 3.719,0.885 4.031,1.083 0.313,0.198 10 false H56
*1 DLC3 - -
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
M43-2 (CA1P) - M43-7 (CA1N) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
M43-2 (CA1P) - M43-10 (BLGD) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M43-7 (CA1N) - M43-10 (BLGD) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M43-2 (CA1P) - H56-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
M43-7 (CA1N) - H56-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




FORWARD RECOGNITION CAMERA (w/ Toyota Safety Sense)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the R5 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

C427754C01
3.76,0.75 4.156,1 0.396,0.25 0.844,0.76 1.24,1.01 0.396,0.25 0.958,0.802 1.271,1 0.313,0.198 10 false R5 0.417,0.208 0.729,0.406 0.313,0.198 10 false *a 3.646,0.26 3.958,0.458 0.313,0.198 10 false *1 3.833,0.792 4.146,0.99 0.313,0.198 10 false H56
*1 DLC3 - -
*a Front view of wire harness connector
(to Forward Recognition Camera)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
R5-5 (CA1P) - R5-11 (CA1N) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
R5-5 (CA1P) - R5-10 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R5-11 (CA1N) - R5-10 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R5-5 (CA1P) - H56-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
R5-11 (CA1N) - H56-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Toyota Safety Sense)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT RADAR SENSOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the B6 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C427755C01
0.729,0.792 1.115,1.042 0.385,0.25 3.719,0.823 4.146,1.063 0.427,0.24 3.594,0.177 3.906,0.375 0.313,0.198 10 false *1 0.708,0.135 1.021,0.333 0.313,0.198 10 false *a 0.833,0.813 1.146,1.01 0.313,0.198 10 false B6 3.802,0.854 4.115,1.052 0.313,0.198 10 false H56
*1 DLC3 - -
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
B6-3 (CA2H) - B6-2 (CA2L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
B6-3 (CA2H) - B6-1 (SGND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B6-2 (CA2L) - B6-1 (SGND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B6-3 (CA2H) - H56-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
B6-2 (CA2L) - H56-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




REAR TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the W15 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C427757C01
0.635,0.75 1.031,1.031 0.396,0.281 3.719,0.792 4.115,1.073 0.396,0.281 0.5,0.219 0.813,0.417 0.313,0.198 10 false *a 3.458,0.25 3.771,0.448 0.313,0.198 10 false *1 3.771,0.844 4.083,1.042 0.313,0.198 10 false H56 0.698,0.802 1.104,1.01 0.406,0.208 10 false W15
*1 DLC3 - -
*a Front view of wire harness connector
(to Rear Television Camera Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
W15-4 (CANH) - W15-1 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
W15-4 (CANH) - H56-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
W15-1 (CANL) - H56-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
W15-4 (CANH) - H56-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
W15-1 (CANL) - H56-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




TIRE PRESSURE WARNING ECU AND RECEIVER


Refer to Terminals of ECU.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the M51 tire pressure warning ECU and receiver connector.


c.
C427521C03
0.323,0.906 0.74,1.177 0.417,0.271 0.146,0.156 0.458,0.354 0.313,0.198 10 false *a 0.406,0.948 0.75,1.208 0.344,0.26 10 false M51
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
M51-9 (CANH) - M51-10 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
M51-9 (CANH) - M51-12 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M51-10 (CANL) - M51-12 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M51-9 (CANH) - M51-7 (+B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
M51-10 (CANL) - M51-7 (+B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




METER MIRROR SUB-ASSEMBLY (w/ Headup Display System)


Refer to Terminals of ECU.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>HEADUP DISPLAY SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H31 meter mirror sub-assembly connector.


c.
C427758C01
1.5,0.177 1.896,0.458 0.396,0.281 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 1.583,0.229 1.896,0.427 0.313,0.198 10 false H31
*a Front view of wire harness connector
(to Meter Mirror Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H31-12 (MPX1) - H31-13 (MPX2) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H31-12 (MPX1) - H31-4 (ES) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H31-13 (MPX2) - H31-4 (ES) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H31-12 (MPX1) - H31-2 (B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H31-13 (MPX2) - H31-2 (B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/o Parking Support Brake System)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H46 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C427760C01
0.281,0.771 0.656,1.01 0.375,0.24 3.865,0.771 4.24,1.01 0.375,0.24 3.74,0.188 4.052,0.385 0.313,0.198 10 false *1 0.469,0.146 0.781,0.344 0.313,0.198 10 false *a 3.938,0.802 4.25,1 0.313,0.198 10 false H56 0.344,0.813 0.656,1.01 0.313,0.198 10 false H46
*1 DLC3 - -
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H46-17 (R1) - H46-18 (R2) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H46-17 (R1) - H46-28 (E) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H46-18 (R2) - H46-28 (E) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H46-17 (R1) - H56-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H46-18 (R2) - H56-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




PARKING ASSIST ECU (w/ Panoramic View Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H20 parking assist ECU connector.


c.
C427761C01
1.51,0.156 1.927,0.406 0.417,0.25 0.156,0.094 0.469,0.292 0.313,0.198 10 false *a 1.604,0.208 2.031,0.406 0.427,0.198 10 false H20
*a Front view of wire harness connector
(to Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H20-11 (CANH) - H20-12 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H20-11 (CANH) - H20-4 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H20-12 (CANL) - H20-4 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H20-11 (CANH) - H20-1 (+B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H20-12 (CANL) - H20-1 (+B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




POSITION CONTROL ECU ASSEMBLY LH (w/ Seat Position Memory System)


Refer to Terminals of ECU.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the e23 and e25 position control ECU assembly LH connectors.


c.

Measure the resistance according to the value(s) in the table below.

C427762C01
0.469,0.76 0.844,1.021 0.375,0.26 4,0.802 4.375,1.063 0.375,0.26 0.198,0.188 0.51,0.385 0.313,0.198 10 false *a 0.542,0.802 0.854,1 0.313,0.198 10 false e25 4.063,0.844 4.375,1.042 0.313,0.198 10 false e23
*a Front view of wire harness connector
(to Position Control ECU Assembly LH)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
e25-13 (CANP) - e25-14 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
e25-13 (CANP) - e23-2 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
e25-14 (CANN) - e23-2 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
e25-13 (CANP) - e23-3 (+B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
e25-14 (CANN) - e23-3 (+B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




OUTER MIRROR CONTROL ECU ASSEMBLY LH (w/ Seat Position Memory System)


Refer to Terminals of ECU.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the J23 outer mirror control ECU assembly LH connector.


c.
C427144C03
0.313,1.063 0.688,1.313 0.375,0.25 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 0.396,1.094 0.708,1.292 0.313,0.198 10 false J23
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J23-9 (CANP) - J23-8 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
J23-9 (CANP) - J23-7 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
J23-8 (CANN) - J23-7 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
J23-9 (CANP) - J23-6 (CPUB) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
J23-8 (CANN) - J23-6 (CPUB) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




OUTER MIRROR CONTROL ECU ASSEMBLY RH (w/ Seat Position Memory System)


Refer to Terminals of ECU.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the J7 outer mirror control ECU assembly RH connector.


c.
C427144C04
0.313,1.063 0.688,1.313 0.375,0.25 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 0.438,1.094 0.75,1.292 0.313,0.198 10 false J7
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J7-9 (CANP) - J7-8 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
J7-9 (CANP) - J7-7 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
J7-8 (CANN) - J7-7 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
J7-9 (CANP) - J7-6 (CPUB) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
J7-8 (CANN) - J7-6 (CPUB) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




MULTIPLEX NETWORK DOOR ECU (w/ Power Back Door System)


Refer to Terminals of ECU.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the W18 multiplex network door ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

C427763C02
0.313,0.771 0.688,1.063 0.375,0.292 3.729,0.76 4.104,1.052 0.375,0.292 0.542,0.229 0.854,0.427 0.313,0.198 10 false *a 3.406,0.198 3.719,0.396 0.313,0.198 10 false *1 0.354,0.833 0.771,1.052 0.417,0.219 10 false W18 3.802,0.823 4.219,1.042 0.417,0.219 10 false H56
*1 DLC3 - -
*a Front view of wire harness connector
(to Multiplex Network Door ECU)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
W18-39 (CANP) - W18-40 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
W18-39 (CANP) - H56-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
W18-40 (CANN) - H56-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
W18-39 (CANP) - W18-20 (ECUB) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
W18-40 (CANN) - W18-20 (ECUB) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher