Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV BATTERY
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0419999 HV BATTERY N

HYBRID / BATTERY CONTROL  HV BATTERY  CHARGING  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced when charging the HV battery are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>PRECAUTION

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1.INSPECT AUXILIARY BATTERY VOLTAGE

a.

Measure the auxiliary battery voltage.

Standard Voltage:

Approximately 11 V or more


HINT:
·

The horn should sound clearly.

·

If the voltage is 10 V or less, either charge the auxiliary battery (charging usually takes about 1 hour), or replace it with an auxiliary battery that is already charged.




Hide 2. PREPARATION FOR HV BATTERY CHARGING

CAUTION:
·

The hybrid system has high-voltage circuits. Accidents, such as electric shock, or electric leaks may result if the hybrid system is not operated in a correct manner. Make sure to follow the correct procedure.

·

Be sure to wear insulated gloves.



HINT:
·

Removing the service plug grip interrupts the high voltage circuit.

·

High voltage wiring connectors are orange.



a.

Check the charge level of the HV battery.

i.

If the hybrid system fails to start and "Traction Battery Needs to be Protected Shift into P to Restart" is displayed on the multi-information display, the HV battery may be discharged.


ii.

Confirm if the engine starts. If the engine starts, leave it idling with the shift lever in P until the engine stops (self charge has completed).

If the engine cannot start, charge the HV battery.

HINT:
·

Before performing external charging, always use the GTS to perform troubleshooting.

·

Charging time using a THS charger is 10 minutes per charge cycle. The charging time when using the THS charger is a short charging time (when the HV battery temperature is 25°C (77°F), 10 minutes may be sufficient, if the HV battery temperature is 0°C (32°F), then three 10 minute charge cycles may be required) for putting the engine in a condition where it can be started (the system can enter the READY-on state). (The THS charger will automatically stop 10 minutes after charging starts.)






c.

Check the terminal voltage.

i.

Disconnect the engine room main wire.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>FRAME WIRE>REMOVAL


ii.


iv.

Install the connector cover assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


v.




f.

Separate the front floor carpet assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL


g.

h.

Remove the No. 10 HV battery shield panel.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


i.

Disconnect the HV floor under wire.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


j.

Inspect the electrical insulation of the HV battery.

i.
A455557C01
1.313,0.979 1.646,0.979 true 2.177,1.219 1.885,1.219 true 0.094,0.094 0.26,0.281 0.167,0.188 10 true *a 1.135,0.885 1.292,1.083 0.156,0.198 10 true 1 2.219,1.135 2.375,1.333 0.156,0.198 10 true 2
*a Service Plug Grip Removed
(Service Plug Grip Connecting Terminals)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
1 - Body ground Ignition switch off 10 MΩ or higher
2 - Body ground Ignition switch off 10 MΩ or higher



ii.
A455558C01
1.542,0.646 1.823,0.854 0.281,0.208 1.948,1.125 2.229,1.333 0.281,0.208 1.125,1.24 1.406,0.958 true 2.146,1.74 1.802,1.271 true 0.115,0.104 0.365,0.323 0.25,0.219 10 true *a 1.563,0.667 1.802,0.833 0.24,0.167 10 true Q2 1.958,1.146 2.208,1.313 0.25,0.167 10 true Q3 1,1.281 1.292,1.479 0.292,0.198 10 true CBI 2.198,1.688 2.49,1.885 0.292,0.198 10 true CEI
*a Component without harness connected
(HV Battery Junction Block Assembly)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
Q2-1 (CBI) - Body ground Ignition switch off 10 MΩ or higher
Q3-1 (CEI) - Body ground Ignition switch off 10 MΩ or higher




k.

Connect the THS charger in the order shown in the illustration.

A455559C01
2.573,4.792 2.302,6.146 2.302,6.146 2.083,6.146 true 2.406,1.323 2.177,1.021 2.177,1.021 1.969,1.021 true 4.698,4.531 4.875,4.99 4.875,4.99 5.063,4.99 true 1.875,4.865 1.594,5.958 1.594,5.958 1.385,5.958 true 2.542,0.542 2.74,0.396 2.74,0.396 2.885,0.396 true 3.219,1.438 4.26,1.396 4.26,1.396 4.563,1.396 true 5.177,6.021 6.198,6.021 true 6.031,7.656 6.49,7.656 false 3.021,7.708 3.479,7.708 false 2.917,7.365 3.375,7.365 false 4.521,6.427 4.521,6.74 true 4.865,6.333 5.104,6.792 5.104,6.792 5.229,6.792 true 3.552,1.094 4.292,0.646 4.292,0.646 4.438,0.646 true 5.094,4.906 5.281,5.073 0.188,0.167 10 true *1 1.927,6.073 2.24,6.229 0.313,0.156 10 false *2 1.219,5.885 1.531,6.042 0.313,0.156 10 false *3 4.469,0.563 5.073,0.74 0.604,0.177 10 false 3 SST *a 2.927,0.313 3.573,0.5 0.646,0.188 10 true 5 SST *b 1.323,0.938 1.917,1.115 0.594,0.177 10 true 1 SST *c 2.438,7.625 3.042,7.823 0.604,0.198 10 false 8 SST *d 2.76,7.26 3.073,7.417 0.313,0.156 10 false *e 6.521,7.563 7.01,7.74 0.49,0.177 10 false SST *f 4.208,6.75 4.813,6.927 0.604,0.177 10 true 4 SST *a 6.229,5.927 6.875,6.115 0.646,0.188 10 false 6 SST *b 4.594,1.323 5.188,1.5 0.594,0.177 10 true 2 SST *c 5.25,6.698 5.844,6.875 0.594,0.177 10 true 7 SST *c
*1 HV Battery *2 HV Floor Under Wire
*3 Inverter with Converter Assembly - -
*a EV Bonding Cable (Green Cable) *b Low Voltage Cable
*c High Voltage Cable *d Power Input Plug
*e Grounded AC 100 to 240 V Receptacle *f THS Charger


NOTICE:

Connect all of the THS charger cables in the order shown in the illustration to prevent electrical shock.



l.
A455560N01
1.906,1.052 1.688,1.052 1.688,1.052 1.594,1.385 true 1.927,0.958 2.24,1.135 0.313,0.177 10 true SST

Connect the 2 SST (high voltage cable) connectors to the HV battery junction block assembly.

SST
09882-10090  


m.

Connect the SST (high voltage cable) terminal to the position shown in the illustration with the nut.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


n.
A455561N01
2.406,0.625 2.698,0.625 2.698,0.625 2.885,1.094 true 2.063,0.531 2.385,0.729 0.323,0.198 10 true SST

Connect the SST (EV bonding cable (green cable)) terminal to the position shown in the illustration with the nut.

SST
09882-10070  

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


o.
A208147C02
0.906,1.76 1.542,1.76 true 2.365,1.458 2.365,1.802 true 0.448,1.677 0.958,2.021 0.51,0.344 10 false SST *a 2.25,1.844 2.729,2.135 0.479,0.292 10 false SST *b
*a EV Bonding Cable (Green Cable)
*b THS Charger


Connect the SST (EV bonding cable (green cable)) terminal to SST (THS charger).

SST
09880-10021  (09881-10041)


p.
A455562N01
1.385,0.948 1.563,0.948 1.563,0.948 1.802,0.531 true 1.042,0.854 1.375,1.042 0.333,0.188 10 true SST

Connect the SST (low voltage cable) terminal to the position shown in the illustration with the nut.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


q.
A305318C08
1.365,0.906 1.104,0.427 1.104,0.427 0.729,0.427 false 2.844,2.563 2.844,1.813 false 2.771,0.458 3.375,0.917 0.604,0.458 10 true 1 SST *a 0.167,2.375 0.75,2.833 0.583,0.458 10 true 2 SST *b 0.26,0.333 0.75,0.635 0.49,0.302 10 false SST *c 2.74,2.615 3.292,3.042 0.552,0.427 10 false SST *d
*a Low Voltage Cable
*b High Voltage Cable
*c THS Charger
*d Power Input Plug


Connect SST (low voltage cable) and SST (high voltage cable) to SST (THS charger) in the order shown in the illustration.



s.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>INSTALLATION


t.

Connect SST (power input plug) of SST (THS charger) to a grounded AC 100 to 240 V receptacle.

SST
09881-10081  09881-10090  09881-10050  09881-10100  09881-10110  09881-10130  

NOTICE:

Always use an AC 100 to 240 V receptacle with a properly functioning ground. The ground is designed to reduce the chance of electric shock if a malfunction occurs. Do not use the charger if any of the pins on its plug have been damaged or removed.



Hide 3. HV BATTERY CHARGING

a.

Check the value of the Data List item while performing the Active Test.

Powertrain > Hybrid Control > Active Test
Active Test Display
Hybrid Battery Charge
Data List Display
SMRG Status
SMRB Status
50004 397 42001 48,50
HINT:

If the values of the Data List items are not as specified in the table below, turn the GTS and the ignition switch off and then perform the HV battery charging procedure again.


"System Main Relay Status - SMRB" and "System Main Relay Status - SMRG" in Data List during "Battery Charge" Active Test:
Step Active Test
"Battery Charge"
THS charger START
Switch
Data List
"System Main Relay Status - SMRB"
Data List
"System Main Relay Status - SMRG"
1 OFF OFF OFF OFF
2 OFF → ON OFF OFF → ON OFF → ON
3 ON OFF → ON ON ON



b.

Make sure that the EMERGENCY STOP switch is in the reset condition (the switch is turned clockwise and released).


c.

Make sure that the BREAKER is in the ON position.


d.
A208150

Turn the THS charger MAIN switch on.

HINT:

The MAIN indicator will illuminate (green).



e.

Press the START switch.

A208151

HINT:
·

When the START switch is turned on, the INITIAL CHECK indicator illuminates and an initial check starts. When the initial check completes successfully, the INITIAL CHECK indicator turns off, the CHARGING indicator illuminates and charging will start at the same time.

·

While the INITIAL CHECK indicator is illuminated, the insulation, 400 V output, emergency stop switch, connector connections and ground connection are inspected.




f.

Repeat the charge cycle 3 times. When the last cycle has finished, turn the THS charger MAIN switch off.

HINT:
·

Charging time using the THS charger is 10 minutes per charge cycle. The charging time when using a THS charger is a short charging time (when the battery temperature is 25°C (77°F), 10 minutes may be sufficient, if the battery temperature is 0°C (32°F), then three 10 minute charge cycles may be required) for putting the engine in a condition where it can be started (the system can enter the READY-on state). (The THS charger will automatically stop 10 minutes after charging starts.)

·

There is very little chance of overcharging the HV battery during the second or third charging cycle. The SOC will not likely increase beyond the upper limit because it was low enough to prevent the engine from starting. Even if the SOC was to increase enough to exceed the limit, the hybrid vehicle control ECU will stop the Active Test to prevent overcharging.

·

Cranking the engine once causes the SOC to drop approximately 1%.

·

Charging the HV battery once (10 minutes) using the THS charger restores the SOC approximately 2%.




g.

Turn the ignition switch off.


h.

Remove the THS charger and connect the HV floor under wire (for HV Battery).

i.

Disconnect SST (power inlet plug) of SST (THS charger) from the grounded AC 100 to 240 V receptacle.


ii.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>REMOVAL



iv.
A305317C09
1.198,0.948 0.969,0.406 0.969,0.406 0.74,0.406 false 2.823,0.469 3.417,0.771 0.594,0.302 10 true 2 SST *a 0.26,2.396 0.854,2.74 0.594,0.344 10 true 1 SST *b 0.271,0.323 0.781,0.677 0.51,0.354 10 false SST *c
*a Low Voltage Cable
*b High Voltage Cable
*c THS Charger


Disconnect SST (high voltage cable) and SST (low voltage cable) from SST (THS charger) in the order shown in the illustration.


v.
A455562N01
1.385,0.948 1.563,0.948 1.563,0.948 1.802,0.531 true 1.042,0.854 1.375,1.042 0.333,0.188 10 true SST

Remove the nut and disconnect the SST (low voltage cable) terminal.


vi.
A208147C03
0.906,1.76 1.542,1.76 true 2.365,1.458 2.365,1.802 true 0.427,1.688 0.938,2.031 0.51,0.344 10 false SST *a 2.198,1.844 2.677,2.135 0.479,0.292 10 false SST *b
*a EV Bonding Cable (Green Cable)
*b THS Charger


Disconnect the SST (EV bonding cable (green cable)) terminal from SST (THS charger).


vii.
A455561N01
2.406,0.625 2.698,0.625 2.698,0.625 2.885,1.094 true 2.063,0.531 2.385,0.729 0.323,0.198 10 true SST

Remove the nut and disconnect the SST (EV bonding cable (green cable)) terminal.


viii.
A455560N01
1.906,1.052 1.688,1.052 1.688,1.052 1.594,1.385 true 1.927,0.958 2.24,1.135 0.313,0.177 10 true SST

Remove the nut and disconnect the SST (high voltage cable) terminal.


ix.

Disconnect the 2 SST (high voltage cable) connectors from the HV battery junction block assembly.


x.

xi.

Install the No. 10 HV battery shield panel.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>INSTALLATION



xiii.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>INSTALLATION



i.

Turn the ignition switch to ON (READY) and check if the engine starts.

HINT:

If the engine does not start, perform the HV battery charging operation again.




k.

Install the front floor carpet assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>INSTALLATION




Hide 4. CHECK HV BATTERY AFTER HV BATTERY CHARGE


b.

Perform the self-charging operation.

i.

Start the engine and leave it idling with the shift lever in P until the engine stops.

HINT:

When the engine stops idling, this indicates that self-charging is complete. Perform any initialization procedures required after the negative (-) auxiliary battery terminal is disconnected and reconnected.