Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER (for Gasoline Model) › from 2020.11
RM37A0E _53 Suspension _086866 REAR SUSPENSION _0417445 REAR SUSPENSION MEMBER(for Gasoline Model) A

REAR SUSPENSION  REAR SUSPENSION MEMBER(for Gasoline Model)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL HOLE PLUG

a.
C336837

Install the 13 hole plugs to the rear suspension member sub-assembly as shown in the illustration.

HINT:

The upper and lower hole plug shapes are different.



Hide 52271D 2.INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for LH Side)

a.
C427657C01
0.052,0.052 0.365,0.292 0.313,0.24 10 false *a
*a View from Underneath
V100135

Front of the Vehicle
V100136

Outside of the Vehicle


Confirm the installation direction and temporarily install a new rear suspension member front body mounting cushion.

NOTICE:
·

Position the rear suspension member front body mounting cushion in the correct direction.

·

Do not apply lubricant to the outer sleeve of the rear suspension member front body mounting cushion.




b.
C199924N10
2.063,0.438 2.354,0.438 false 2.042,0.698 2.51,0.698 true 2.385,0.375 2.719,0.583 0.333,0.208 10 false SST 2.552,0.625 2.885,0.844 0.333,0.219 10 false SST

Install SST as shown in the illustration.

SST
09527-17011  
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

Apply molybdenum grease to the threads and tip of the SST center bolt before use.


HINT:

Use SST with the "F" mark facing the rear suspension member front body mounting cushion.



c.
C199927C05
1.427,0.74 1.031,0.74 true 1.448,0.969 1.229,0.969 false 0.75,0.677 1.063,0.896 0.313,0.219 10 false SST 0.938,0.906 1.25,1.146 0.313,0.24 10 false SST 2.25,1.917 2.563,2.073 0.313,0.156 10 false *a 2.823,0.938 3.135,1.094 0.313,0.156 10 false *b
*a Hold
*b Turn


Using SST, install the rear suspension member front body mounting cushion until there is no clearance between the rear suspension member sub-assembly and rear suspension member front body mounting cushion.

SST
09527-17011  
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.



d.

Remove SST from the rear suspension member sub-assembly.


Hide 52271D 3.INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for RH Side)

a.
C427658C01
0.073,0.063 0.375,0.313 0.302,0.25 10 false *a
*a View from Underneath
V100135

Front of the Vehicle
V100136

Outside of the Vehicle


Confirm the installation direction and temporarily install a new rear suspension member front body mounting cushion.

NOTICE:
·

Position the rear suspension member front body mounting cushion in the correct direction.

·

Do not apply lubricant to the outer sleeve of the rear suspension member front body mounting cushion.




b.
C205620N08
1.396,0.396 1.208,0.396 false 1.427,0.688 0.99,0.688 false 0.708,0.625 1.094,0.854 0.385,0.229 10 false SST 0.917,0.323 1.219,0.521 0.302,0.198 10 false SST

Install SST as shown in the illustration.

SST
09527-17011  
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

Apply molybdenum grease to the threads and tip of the SST center bolt before use.


HINT:

Use SST with the "F" mark facing the rear suspension member front body mounting cushion.



c.
C205621C04
1.479,0.792 1.167,0.792 true 1.479,0.979 1.25,0.979 true 0.885,0.719 1.229,0.906 0.344,0.188 10 true SST 0.969,0.917 1.26,1.104 0.292,0.188 10 true SST 2.333,1.927 2.646,2.083 0.313,0.156 10 false *a 2.979,1.01 3.292,1.167 0.313,0.156 10 false *b
*a Hold
*b Turn


Using SST, install the rear suspension member front body mounting cushion until there is no clearance between the rear suspension member sub-assembly and rear suspension member front body mounting cushion.

SST
09527-17011  
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.



d.

Remove SST from the rear suspension member sub-assembly.


Hide 52276A 4.INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION LH

a.
C427659C01
0.104,0.052 0.417,0.365 0.313,0.313 10 false *a 3.021,1.521 3.333,1.719 0.313,0.198 10 false *b 1.229,1.51 1.542,1.708 0.313,0.198 10 false *b
*a View from Underneath
*b 15°
V100135

Front of the Vehicle
V100136

Outside of the Vehicle


Confirm the installation direction and temporarily install a new rear suspension member rear body mount cushion LH.

NOTICE:
·

Position the rear suspension member rear body mount cushion LH in the correct direction.

·

Do not apply lubricant to the outer sleeve of the rear suspension member rear body mount cushion LH.




b.
C199925N12
1.292,0.417 1.5,0.417 1.5,0.417 1.542,0.531 false 1.021,0.344 1.375,0.604 0.354,0.26 10 false SST

Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

Apply molybdenum grease to the threads and tip of the SST center bolt before use.


HINT:

Use SST with the "F" mark facing the rear suspension member rear body mount cushion LH.



c.
C199928C06
1.5,0.74 1.469,0.604 1.469,0.604 1.01,0.604 true 0.74,0.542 1.073,0.76 0.333,0.219 10 true SST 2.292,1.917 2.604,2.073 0.313,0.156 10 false *a 2.969,0.99 3.281,1.146 0.313,0.156 10 false *b
*a Hold
*b Turn


Using SST, install the rear suspension member rear body mount cushion LH until there is no clearance between the rear suspension member sub-assembly and rear suspension member rear body mount cushion LH.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.



d.

Remove SST from the rear suspension member sub-assembly.


Hide 52275B 5.INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION RH

a.
C427660C01
0.104,0.063 0.417,0.219 0.313,0.156 10 false *a
*a View from Underneath
V100135

Front of the Vehicle
V100136

Outside of the Vehicle


Confirm the installation direction and temporarily install a new rear suspension member rear body mount cushion RH.

NOTICE:
·

Position the rear suspension member rear body mount cushion RH in the correct direction.

·

Do not apply lubricant to the outer sleeve of the rear suspension member rear body mount cushion RH.




b.
C199926N12
1.906,0.521 2.042,0.271 2.042,0.271 2.135,0.271 false 2.177,0.198 2.531,0.417 0.354,0.219 10 false SST

Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

Apply molybdenum grease to the threads and tip of the SST center bolt before use.


HINT:

Use SST with the "F" mark facing the rear suspension member rear body mount cushion RH.



c.
C199929C06
1.49,0.729 1.427,0.563 1.427,0.563 1.167,0.563 false 0.854,0.479 1.177,0.719 0.323,0.24 10 false SST 2.25,1.896 2.563,2.052 0.313,0.156 10 false *a 2.906,1.021 3.219,1.177 0.313,0.156 10 false *b
*a Hold
*b Turn


Using SST, install the rear suspension member rear body mount cushion RH until there is no clearance between the rear suspension member sub-assembly and rear suspension member rear body mount cushion RH.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.



d.

Remove SST from the rear suspension member sub-assembly.


Hide 48790 6.INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH

Hide 48770A 7.INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 52272 8.INSTALL REAR SUSPENSION MEMBER UPPER STOPPER

a.

Install the 2 rear suspension member upper stoppers to the rear suspension member sub-assembly.


Hide 52278A 9.INSTALL REAR SUSPENSION MEMBER LOWER STOPPER RETAINER

a.

Install the 2 rear suspension member lower stopper retainers to the rear suspension member sub-assembly.


Hide 51206A 10.INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.
C426736C01
2.865,3.844 2.865,3.708 2.865,3.708 3,3.708 false 0.677,4.385 0.677,4 true 1.677,4.417 1.677,4.021 true 2.115,3.75 2.396,3.135 2.396,3.135 2.583,3.135 true 2.458,4.427 2.458,3.896 true 3,3.615 3.177,3.813 0.177,0.198 10 false *a 0.615,4.427 0.927,4.583 0.313,0.156 10 false *b 2.385,4.417 2.698,4.573 0.313,0.156 10 false *c 2.604,3.042 2.844,3.24 0.24,0.198 10 true *b 1.615,4.417 1.927,4.573 0.313,0.156 10 false *c
*a Engine Lifter
*b Attachment
*c Wooden Block
V100155

Attachment and Wooden Block Placement Location


Using an engine lifter, 2 attachments and 2 wooden blocks or equivalent tools, support the rear suspension member sub-assembly, and raise the rear suspension member sub-assembly until there is no clearance between the rear suspension member sub-assembly and vehicle body.

CAUTION:
C426729

·

The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:
·

Use attachments and wooden blocks to keep the rear suspension member sub-assembly level.

·

Keep supporting the rear suspension member sub-assembly until the installation has been completed.




b.

Install the rear suspension member sub-assembly with the 2 rear lower suspension braces, rear lower suspension member stopper LH and rear lower suspension member stopper RH, with the 4 bolts and 2 nuts.

C426737C01
0.552,1.521 0.552,1.313 0.552,1.313 0.646,1.313 false 6.615,1.531 6.615,1.323 6.615,1.323 6.521,1.323 false 0.469,1.542 0.781,1.74 0.313,0.198 10 false *1 6.531,1.531 6.844,1.729 0.313,0.198 10 false *1
*1 Rear Lower Suspension Brace - -


Torque:
Bolt : 158 N*m (1611 kgf*cm, 117 ft.*lbf)
Nut : 32 N*m (326 kgf*cm, 24 ft.*lbf)

NOTICE:

Be sure to install the rear suspension member sub-assembly with the rear lower suspension braces facing in the correct direction as shown in the illustration.



Hide 82164 11.INSTALL FRAME WIRE (for 4WD/AWD)

a.

Install the frame wire to the rear suspension member sub-assembly with the bolt and clamp.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 41651 12.INSTALL REAR NO. 1 DIFFERENTIAL MOUNT CUSHION (for 4WD/AWD)

Hide 41110 13.INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY (for Dynamic Torque Control AWD)

Hide 41110 14.INSTALL TORQUE VECTORING DIFFERENTIAL CARRIER ASSEMBLY (for Dynamic Torque Vectoring AWD)

Hide 42341C 15.INSTALL REAR DRIVE SHAFT LH SNAP RING (for 4WD/AWD)

Hide 42341B 16.INSTALL REAR DRIVE SHAFT RH SNAP RING (for 4WD/AWD)

HINT:

Perform the same procedure as for the LH side.


Hide 42340B 17.INSTALL REAR DRIVE SHAFT ASSEMBLY LH (for 4WD/AWD)

Hide 42330 18.INSTALL REAR DRIVE SHAFT ASSEMBLY RH (for 4WD/AWD)

HINT:

Perform the same procedure as for the LH side.


Hide 48790 19.TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH

a.
C426738

Using a brass bar and a hammer, push out the bushing until it is positioned as shown in the illustration.

HINT:

Pushing out the bushing makes it easier to connect the rear upper control arm assembly LH.



b.
C426727

Temporarily install the rear axle carrier sub-assembly to the rear upper control arm assembly with the bolt and nut.

NOTICE:
·

Insert the bolt with the threaded end facing the rear of the vehicle.

·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.




Hide 48770A 20.TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48720A 21.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 22.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48740F 23.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 24.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48258C 25.INSTALL REAR LOWER COIL SPRING INSULATOR LH

Hide 48258B 26.INSTALL REAR LOWER COIL SPRING INSULATOR RH

HINT:

Perform the same procedure as for the LH side.


Hide 48231B 27.INSTALL REAR COIL SPRING LH

Hide 48231A 28.INSTALL REAR COIL SPRING RH

HINT:

Perform the same procedure as for the LH side.


Hide 48835 29.INSTALL REAR LOWER STABILIZER BRACKET

Hide 48812 30.INSTALL REAR STABILIZER BAR

Hide 31.TEMPORARILY INSTALL REAR STABILIZER LINK ASSEMBLY LH

Hide 32.TEMPORARILY INSTALL REAR STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 89544E 33.INSTALL REAR SKID CONTROL SENSOR LH (for 4WD/AWD)

Hide 89544D 34.INSTALL REAR SKID CONTROL SENSOR RH (for 4WD/AWD)

HINT:

Perform the same procedure as for the LH side.


Hide 890C0A 35.CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY (for 4WD/AWD)

a.

Connect the No. 2 parking brake wire assembly connector to the rear skid control sensor.


Hide 890C0 36.CONNECT NO. 1 PARKING BRAKE WIRE ASSEMBLY (for 4WD/AWD)

HINT:

Perform the same procedure as for the LH side.


Hide 42312B 37.INSTALL REAR AXLE SHAFT NUT LH (for 4WD/AWD)

Hide 42311N 38.INSTALL REAR AXLE SHAFT NUT RH (for 4WD/AWD)

HINT:

Perform the same procedure as for the LH side.


Hide 47319F 39.CONNECT REAR FLEXIBLE HOSE LH

a.
C424684

Connect the rear flexible hose LH to the rear upper control arm assembly LH with the bolt.

Torque:
18.8 N*m (192 kgf*cm, 14 ft.*lbf)


Hide 47318F 40.CONNECT REAR FLEXIBLE HOSE RH

HINT:

Perform the same procedure as for the LH side.


Hide 48720A 42.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 43.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48740F 44.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

a.

Install the rear No. 2 suspension arm assembly LH (rear axle carrier sub-assembly side) with the bolt.

Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION


Hide 48730F 45.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 46.INSTALL REAR STABILIZER LINK ASSEMBLY LH

Hide 47.INSTALL REAR STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48790 48.INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH

a.

Install the rear upper control arm assembly to the rear axle carrier sub-assembly with the bolt.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 48770A 49.INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48738 50.INSTALL REAR SUSPENSION ARM COVER LH

Hide 48737 51.INSTALL REAR SUSPENSION ARM COVER RH

HINT:

Perform the same procedure as for the LH side.


Hide 37100 52.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD/AWD)

Hide 17430 53.INSTALL TAIL EXHAUST PIPE ASSEMBLY

Hide 54.INSTALL REAR WHEEL

Hide 48740F 55.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

a.

Install the rear No. 2 suspension arm assembly LH (rear suspension member sub-assembly side) with the nut.

Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION


Hide 48730F 56.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 57.ADD DIFFERENTIAL OIL (for 4WD/AWD)

for Dynamic Torque Control AWD: Click hereGeneral>MAINTENANCE>DIFFERENTIAL OIL>REPLACEMENT

for Dynamic Torque Vectoring AWD: Click hereGeneral>MAINTENANCE>DIFFERENTIAL OIL>REPLACEMENT

Hide 58. INSPECT FOR DIFFERENTIAL OIL LEAK (for 4WD/AWD)

Hide 60.INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Hide 62.PERFORM INITIALIZATION

Parking Support Brake System (Click here)
Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)