Home › Engine / Hybrid System › 2TR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY
RM1880E _51 Engine / Hybrid System _013210 2TR-FE ENGINE MECHANICAL _0068470 ENGINE ASSEMBLY A

2TR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 2.REMOVE ENGINE FROM ENGINE STAND

a.

Attach an engine sling device and hang the engine with a chain block.

NOTICE:

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.



b.

Lift the engine and remove it from the engine stand.

NOTICE:

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.



c.

Place the engine onto a workbench.


Hide 3.INSTALL ENGINE ASSEMBLY

a.
A302629
1.24,0.469 1.24,0.542 false
V100135

Lower


Attach the engine sling device and chain block to the engine hangers.


b.

Slowly lower the engine assembly into the engine compartment.


c.

Install the engine mounting brackets with the 4 bolts and 4 nuts.

Torque:
38 N*m (388 kgf*cm, 28 ft.*lbf)


d.

Remove the 2 bolts and 2 engine hangers.


Hide 4.INSTALL REAR END PLATE

a.

Install the end plate with the bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Connect the No. 1 water by-pass pipe to the rear end plate with the bolt.

Torque:
18 N*m (178 kgf*cm, 13 ft.*lbf)


Hide 5.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

Hide 7.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

Hide 8.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 9.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 10.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 11.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear No. 1 engine mounting insulator is necessary.


a.

Install the 4 bolts and rear No. 1 engine mounting insulator.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 12.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)

Hide 13.INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)

Hide 15.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

Hide 17.INSTALL COWL PANEL SUB-ASSEMBLY

a.

Install the cowl panel with the 9 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 18.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 19.INSTALL HOOD ASSEMBLY

a.

Install the hood with the 4 bolts.

Torque:
12 N*m (117 kgf*cm, 8 ft.*lbf)


b.

Connect the washer nozzle hose.


c.

Adjust the hood (See page Vehicle Exterior>DOOR / HATCH>HOOD>ADJUSTMENT).


Hide 21.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Install a new O-ring and the engine oil level dipstick guide with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 22.INSTALL ENGINE OIL LEVEL DIPSTICK

Hide 23.CONNECT VANE PUMP ASSEMBLY

a.

Connect the vane pump with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Connect the oil pressure switch connector.


Hide 24.CONNECT ENGINE WIRE

a.

Connect the wire clamp to the front engine mounting bracket LH with the bolt.

Torque:
13 N*m (128 kgf*cm, 9 ft.*lbf)


b.

Connect the 2 engine room junction block connectors and wire clamp.


c.

Connect the cable to the engine room junction block with the nut.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


d.

Install the engine room relay block cover (side).


e.

Install the engine room relay block cover (upper).


f.

Connect the ground wire with the nut.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


g.
A173606
1.271,1.802 1.625,1.948 0.354,0.146 10 true 45°

Connect the ground wire to the left side of the frame with the bolt so that it is within the range shown in the illustration.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


h.

Connect the sensor bracket to the right side of the frame with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


i.

Connect the heated oxygen sensor connector.


j.

Push the engine wire through the dash panel into the cabin.

HINT:

The wire should be within the range shown in the illustration.



k.

Connect the ground wire with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


l.

Attach the wire harness clamp.


m.

Connect the ECM connectors.

i.

Connect the 4 ECM connectors.


ii.

Install the glove compartment door.



Hide 27.CONNECT HOSE

a.

Connect the vacuum hose (for the brake master cylinder).


b.

Connect the purge line hose.


Hide 28.CONNECT HEATER WATER HOSE

a.

Connect the heater water inlet hose and heater water outlet hose to the heater pipe.


Hide 30.CONNECT OIL COOLER OUTLET HOSE (for Automatic Transmission)

Hide 31.CONNECT OIL COOLER INLET HOSE (for Automatic Transmission)

Hide 32.INSTALL FAN PULLEY

Hide 38.INSTALL INTAKE AIR CONNECTOR AND AIR CLEANER ASSEMBLY

a.

Install the air cleaner and intake air connector assembly with the 4 bolts, and tighten the hose clamp.

Torque:
for air cleaner : 14 N*m (143 kgf*cm, 10 ft.*lbf)
for intake air connector : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
for hose clamp : 5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Connect the mass air flow meter connector and attach the wire harness clamps.


c.

Connect the No. 2 PCV hose.


d.

Connect the vacuum hose.


Hide 39.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 42.ADD AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)

Hide 43.INSPECT AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)

Hide 44.ADD MANUAL TRANSMISSION OIL (for Manual Transmission)