The push-button start function uses a push-type engine switch, which the driver can operate by merely carrying the key. This system consists primarily of the power management control ECU, engine switch, ID code box, steering lock ECU, key, ACC relay, IG1 relay, IG2 relay and certification ECU. The power management control ECU controls the system. This function operates in cooperation with the entry and start system.
Refer to the SFI system*1, *2 or ECD system*3, *4, *5 (DTC P0617):
*1: for 1GR-FE (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0617).
*2: for 2TR-FE (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>P0617).
*3: for 1KD-FTV (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>P0617).
*4: for 1GD-FTV (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>P0617).
*5: for 1GD-FTV (w/ Urea SCR System) (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P0617).
Refer to DTC B2284 (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>B2284).
When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
After the certification ECU, steering lock actuator assembly (steering lock ECU) and/or ID code box is replaced, perform the registration procedures described in the Service Bulletin.
Place the key on the seat. Move the shift lever to P*1 and depress the brake pedal*1 or clutch pedal*2.
*1: for Automatic Transmission
*2: for Manual Transmission
Check that the engine switch indicator is illuminated in green, push the engine switch, and check that the engine starts.
Open and close the driver side door with the engine switch off.
Check if the engine can be started.
Engine can be started.
After the battery is discharged and then recharged, the engine may not start unless the steering lock is initialized using the above procedure.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Read the value using the intelligent tester (Power Supply Open).
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Entry&Start / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Power Supply Open | Power supply open / OK or NG (Past) | OK: Power supply normal
NG (Past): Power supply open occurred in past |
- |
Check for DTCs.
Enter the following menus: Body / (desired system) / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| No DTC is output, power supply open has not occurred in past | A |
| DTCs other than B2782 are output | B |
| Power supply open has occurred in past and/or DTC B2782 is output | C |
A
B
C
Check if the power source mode changes.
When the key is inside the vehicle and the shift lever is in P*, push the engine switch and check that the power source mode changes.
*: for Automatic Transmission
| Result | Proceed to |
|---|---|
| OK: off → on (ACC) → on (IG) → off | A |
| Power source mode does not change to on (IG) or on (ACC). | B |
| Power source mode does not change to on (IG). | C |
| Power source mode does not change to on (ACC). | D |
A
B
C
D
Check the engine cranking function.
for Automatic Transmission: When there is fuel in the fuel tank, the key is inside the vehicle and the shift lever is in P, check that depressing the brake pedal and pressing the engine switch cranks the engine.
for Manual Transmission: When there is fuel in the fuel tank and the key is inside the vehicle, check that depressing the clutch pedal and pressing the engine switch cranks the engine.
Engine cranks.
| Result | Proceed to |
|---|---|
| OK (for 1GR-FE and 2TR-FE) | A |
| OK (for 1KD-FTV and 1GD-FTV) | B |
| NG | C |
for 1GR-FE:
If it is necessary to refer to the SFI system, refer to the following procedure (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
for 2TR-FE:
If it is necessary to refer to the SFI system, refer to the following procedure (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
for 1KD-FTV:
If it is necessary to refer to the ECD system, refer to the following procedure (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
for 1GD-FTV:
If it is necessary to refer to the ECD system, refer to the following procedure (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
for 1GD-FTV (w/ Urea SCR System):
If it is necessary to refer to the ECD system, refer to the following procedure (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>HOW TO PROCEED WITH TROUBLESHOOTING).
A
B
C
for Automatic Transmission:
Disconnect the C159 park/neutral position switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (B) - 5 (L) | Shift lever in P or N | Below 1 Ω |
| Shift lever not in P or N | 10 kΩ or higher |
| *a | Component without harness connected
(Park/Neutral Position Switch) |
for Manual Transmission:
Disconnect the A40*1, A41*2 or r1*3 clutch start switch connector.
*1: for LHD (except 2TR-FE)
*2: for LHD (for 2TR-FE)
*3: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Pushed in
(Clutch pedal depressed) |
Below 1 Ω |
| Released
(Clutch pedal released) |
10 kΩ or higher |
| *a | Component without harness connected
(Clutch Start Switch Assembly) |
OK
NG
for 1GR-FE and 2TR-FE:
Remove the ST relay from the engine room relay block.
Measure the resistance according value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
for 1KD-FTV and 1GD-FTV:
Remove the ST relay from the engine room relay block.
Measure the resistance according value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
OK
NG
Disconnect the G50 power management control ECU connector.
for Automatic Transmission:
Move the shift lever to P or N.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G50-3 (STAR) - Body ground | 20°C (68°F) | 93.8 to 136.3 Ω |
| *a | Rear view of wire harness connector
(to Power Management Control ECU) |
OK
NG
for Automatic Transmission:
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Power Source Control / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Stop Light Switch1 | Stop light switch 1 / ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
ON (brake pedal depressed) or OFF (brake pedal released) appears on the screen according to the condition of the brake pedal.
for Manual Transmission:
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Power Source Control / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Neutral SW/ Clutch SW | Status of the clutch start switch/ ON or OFF | ON: Clutch pedal depressed
OFF: Clutch pedal released |
- |
ON (clutch pedal depressed) or OFF (clutch pedal released) appears on the screen according to the condition of the clutch pedal.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Automatic Transmission) | B |
| NG (for Manual Transmission) | C |
A
B
C
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Power Source Control / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Steering Unlock Switch | Steering unlock switch / ON or OFF | ON: Steering lock released
OFF: Steering lock locked |
- |
ON (steering lock released) or OFF (steering lock locked) appears on the screen according to the steering lock condition.
OK
NG
Turn the engine switch from off to on (ACC) and check that the steering lock moves to the released position.
Lock moves to released position.
OK
NG
Connect the intelligent tester to the DLC3.
Turn the intelligent tester on.
When using the intelligent tester with the engine switch off, turn any of the door courtesy light switches on and off repeatedly at intervals of 1.5 seconds or less until communication between the tester and vehicle starts.
Enter the following menus: Body / Entry&Start / Data List.
According to the display on the intelligent tester, read the Data List.
Turn the engine switch on (IG).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Engine Start Request | Start request signal response / OK or NG | OK: Received
NG: Not received |
- |
OK appears on the screen.
OK
NG
Connect the intelligent tester to the DLC3.
Turn the intelligent tester on.
When using the intelligent tester with the engine switch off, turn any of the door courtesy light switches on and off repeatedly at intervals of 1.5 seconds or less until communication between the tester and vehicle starts.
Enter the following menus: Body / Entry&Start / Data List.
According to the display on the intelligent tester, read the Data List.
Turn the engine switch on (IG).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| L Code Check | L code certification result / OK or NG | OK: L code certification result normal
NG: L code certification result abnormal |
- |
OK (L code certification result normal) appears on the screen.
OK
NG
Connect the intelligent tester to the DLC3.
Turn the intelligent tester on.
When using the intelligent tester with the engine switch off, turn any of the door courtesy light switches on and off repeatedly at intervals of 1.5 seconds or less until communication between the tester and vehicle starts.
Enter the following menus: Body / Entry&Start / Data List.
According to the display on the intelligent tester, read the Data List.
Turn the engine switch on (IG).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| S Code Check | S code certification result / OK or NG | OK: S code certification result normal
NG: S code certification result abnormal |
- |
OK (S code certification result normal) appears on the screen.
OK
NG
Connect the intelligent tester to the DLC3.
Turn the intelligent tester on.
When using the intelligent tester with the engine switch off, turn any of the door courtesy light switches on and off repeatedly at intervals of 1.5 seconds or less until communication between the tester and vehicle starts.
Enter the following menus: Body / Power Source Control / Data List.
According to the display on the intelligent tester, read the Data List.
Turn the engine switch on (IG).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Starter Request Signal | Starter request signal monitor / ON or OFF | ON: ST relay on
OFF: ST relay off |
for Automatic Transmission:
The engine switch is pressed and held with the shift lever in P or N. for Manual Transmission: The engine switch is pressed and held. |
Check that the engine switch indicator is illuminated in green and push the engine switch.
The Data List item changes from OFF to ON when the engine switch is pushed.
| Result | Proceed to |
|---|---|
| OK (for 1GR-FE and 2TR-FE) | A |
| OK (for 1KD-FTV and 1GD-FTV) | B |
| NG | C |
for 1GR-FE:
If it is necessary to refer to the SFI system, refer to the following procedure (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
for 2TR-FE:
If it is necessary to refer to the SFI system, refer to the following procedure (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
for 1KD-FTV:
If it is necessary to refer to the ECD system, refer to the following procedure (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
for 1GD-FTV:
If it is necessary to refer to the ECD system, refer to the following procedure (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
for 1GD-FTV (w/ Urea SCR System):
If it is necessary to refer to the ECD system, refer to the following procedure (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>HOW TO PROCEED WITH TROUBLESHOOTING).
A
B
C
Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION).
OK
NG
Disconnect the G50 power management control ECU connector.
Disconnect the A85 stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G50-11 (STP1) - A85-2 (L) | Always | Below 1 Ω |
| G50-11 (STP1) or A85-2 (L) - Body ground | Always | 10 kΩ or higher |
Reconnect the A85 stop light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G50-11 (STP1) - Body ground | Brake pedal not depressed | Below 1 V |
| Brake pedal depressed | ([Voltage at terminal AM21 or AM22] minus 2.0 V) or higher |
| *a | Rear view of wire harness connector
(to Power Management Control ECU) |
OK
NG
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G35-4 (SLP1) - Body ground | Steering lock locked | 10 kΩ or higher |
| G35-4 (SLP1) - Body ground | Steering lock released | Below 1 Ω |
| *a | Component with harness connected
(Steering Lock ECU) |
| Result | Proceed to | |
|---|---|---|
| OK | A | |
| NG | for Manual Tilt and Manual Telescopic Steering Column | B |
| for Power Tilt and Power Telescopic Steering Column | C | |
A
B
C
Replace the ST relay, park/neutral position switch or clutch start switch with a new or normally functioning part, or repair or replace any damaged wire harness or connector.
NEXT
Connect the intelligent tester to the DLC3.
Turn the intelligent tester on.
When using the intelligent tester with the engine switch off, turn any of the door courtesy light switches on and off repeatedly at intervals of 1.5 seconds or less until communication between the tester and vehicle starts.
Enter the following menus: Body / Power Source Control / Data List.
According to the display on the intelligent tester, read the Data List.
Turn the engine switch on (IG).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Starter Request Signal | Starter request signal monitor / ON or OFF | ON: ST relay on
OFF: ST relay off |
for Automatic Transmission:
The engine switch is pressed and held with the shift lever in P or N. for Manual Transmission: The engine switch is pressed and held. |
Check that the engine switch indicator is illuminated in green and push the engine switch.
The Data List item changes from OFF to ON when the engine switch is pushed.
OK
NG
Place the key on the seat. Move the shift lever to P*1 and depress the brake pedal*1 or clutch pedal*2.
*1: for Automatic Transmission
*2: for Manual Transmission
Check that the engine switch indicator is illuminated in green, push the engine switch and check that the engine starts.
Open and close the driver side door with the engine switch off.
Check if the engine can be started.
Engine can be started.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 1GR-FE and 2TR-FE) | B |
| NG (for 1KD-FTV and 1GD-FTV) | C |
After the battery is discharged and then recharged, the engine may not start unless the steering lock is initialized using the above procedure.
for 1GR-FE:
If it is necessary to refer to the SFI system, refer to the following procedure (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
for 2TR-FE:
If it is necessary to refer to the SFI system, refer to the following procedure (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
for 1KD-FTV:
If it is necessary to refer to the ECD system, refer to the following procedure (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
for 1GD-FTV:
If it is necessary to refer to the ECD system, refer to the following procedure (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
for 1GD-FTV (w/ Urea SCR System):
If it is necessary to refer to the ECD system, refer to the following procedure (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>HOW TO PROCEED WITH TROUBLESHOOTING).
A
B
C