Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › CAMSHAFT (w/o DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052779 1VD-FTV ENGINE MECHANICAL _0255066 CAMSHAFT(w/o DPF) A

1VD-FTV ENGINE MECHANICAL  CAMSHAFT(w/o DPF)  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

When replacing an injector (including interchanging injectors between cylinders), common rail, cylinder head, or intake manifold, replace the corresponding injection pipes with a new one.


PROCEDURE

Hide 13053 2.INSTALL NO. 3 AND NO. 4 CAMSHAFTS

NOTICE:
A168355E05
2.25,0.979 2.771,1.5 2.771,1.5 2.771,1.625 true 1.552,0.625 1.896,0.281 1.896,0.281 2.042,0.281 true 2.344,1.656 3.063,1.823 0.719,0.167 10 false Matchmark 2.115,0.198 2.719,0.344 0.604,0.146 10 false Dot Mark 0.406,1.542 1.833,1.719 1.427,0.177 10 false Number of Gear Teeth

If replacing a camshaft with a new one, make a matchmark on the new camshaft in the same place as the old camshaft. Determine the matchmark placement by using the dot mark as a reference point and counting the number of gear teeth from the dot mark to the matchmark as shown in the illustration.


a.

w/o Intercooler:

When replacing the No. 4 camshaft with a new one, install a new hole plug (See page Engine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY).


b.
A385652

Add more than 19 cc (1.16 cu. in.) of engine oil into the cylinder head side oil holes.


c.
A164816

Apply engine oil to the rollers of the valve rocker arms and the camshaft housing of the cylinder head.


d.
A168401E06
1.594,1.333 1.208,0.188 1.208,0.188 1.74,1.333 true 1.219,0.188 1.031,0.188 false 0.292,0.104 1.01,0.271 0.719,0.167 10 false Matchmark

Install the No. 3 and No. 4 camshafts.

i.

Apply engine oil to the camshaft journals, lobes, thrust portion and gears.


ii.

Align the matchmarks of the No. 3 and No. 4 camshaft timing gears as shown in the illustration.



e.
A168350

Place the camshafts into the cylinder head.

NOTICE:
A164641

Before and after setting the camshafts, firmly set the rocker arms to the lash adjusters.



f.
A168379

Install the No. 4 camshaft bearing cap.

i.

Align the No. 4 camshaft bearing cap and the ring pins of the No. 5 camshaft bearing cap.


ii.

Temporarily install the 4 bolts by hand.



g.
A168380

Install the No. 3 camshaft bearing caps.

i.

Confirm the marks and numbers on the camshaft bearing caps and place them in their proper position and direction.


ii.

Temporarily install the 8 bolts, which are not installed with the oil feed pipe, by hand.



h.
A168381

Temporarily install the No. 3 and No. 4 camshaft oil feed pipes with the 8 bolts by hand.

NOTICE:

If even one of the pipe bolt holes does not match its camshaft bearing cap bolt hole, replace the camshaft oil feed pipe.


HINT:

The pipe is bent on the intake side, and straight on the exhaust side.



i.
A168382

Temporarily install the 2 union bolts by hand.


j.
U163191E02
1.948,1.25 2.104,1.417 0.156,0.167 10 false 1 0.917,1.917 1.094,2.083 0.177,0.167 10 false 10 1.573,1.917 1.729,2.083 0.156,0.167 10 false 2 1.313,0.875 1.49,1.042 0.177,0.167 10 false 11 1.958,0.875 2.115,1.042 0.156,0.167 10 false 3 0.896,0.167 1.073,0.333 0.177,0.167 10 false 12 1.573,0.167 1.729,0.333 0.156,0.167 10 false 4 3.177,1.25 3.354,1.417 0.177,0.167 10 false 13 2.604,1.25 2.76,1.417 0.156,0.167 10 false 5 2.75,1.927 2.927,2.094 0.177,0.167 10 false 14 2.177,1.917 2.333,2.083 0.156,0.167 10 false 6 3.177,0.875 3.354,1.042 0.177,0.167 10 false 15 2.604,0.885 2.76,1.052 0.156,0.167 10 false 7 2.781,0.177 2.958,0.344 0.177,0.167 10 false 16 2.208,0.167 2.365,0.333 0.156,0.167 10 false 8 0.104,1.5 0.281,1.667 0.177,0.167 10 false 17 1.354,1.25 1.51,1.417 0.156,0.167 10 false 9 0.208,1.969 0.385,2.135 0.177,0.167 10 false 18 0.104,0.635 0.281,0.802 0.177,0.167 10 false 19 0.115,0.177 0.292,0.344 0.177,0.167 10 false 20 0.667,2.458 1.792,2.615 1.125,0.156 10 false 12 mm Head Bolt 0.667,2.906 1.792,3.063 1.125,0.156 10 false 10 mm Head Bolt

Uniformly tighten the 20 bolts in several steps in the order shown in the illustration.

Torque:
for 12 mm head bolt of No. 4 camshaft bearing cap : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for 10 mm head bolt of No. 3 camshaft bearing cap : 10 N*m (102 kgf*cm, 7 ft.*lbf)


k.
A168346

Tighten the 2 union bolts.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


l.
A164905

Remove the service bolt from the No. 4 camshaft timing gear.

NOTICE:

Do not drop the bolt into the engine.


HINT:

If the bolt is difficult to remove, rotate the camshaft and remove the bolt. Then realign the matchmarks of the No. 3 and No. 4 camshaft timing gears.



m.
A168366

Temporarily install the No. 2 timing chain and No. 2 camshaft timing sprocket to the No. 3 camshaft with the 2 bolts.


n.
A168364E03
2.712,0.759 3.012,0.918 0.299,0.158 10 SST 2.378,0.174 2.88,0.547 2.88,0.547 2.88,0.717 false

Using SST, hold the No. 2 camshaft timing sprocket. Tighten the 2 bolts.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


o.

Rotate the crankshaft pulley clockwise so that the 2 remaining pump drive shaft gear bolts can be installed.


p.
A168366

Temporarily install the 2 bolts to the No. 3 camshaft.


q.
A168364E03
2.712,0.759 3.012,0.918 0.299,0.158 10 SST 2.378,0.174 2.88,0.547 2.88,0.547 2.88,0.717 false

Using SST, hold the No. 2 camshaft timing sprocket. Tighten the 2 bolts.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


r.
A181679

Remove the hexagon wrench from the No. 2 chain tensioner.


s.

Remove the adhesive from the threads of the taper screw plug and the bolt hole of the timing gear case.


t.
A168340

Apply adhesive to 3 or more threads of the taper screw plug.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



u.
A168320

Using a 10 mm hexagon wrench, install the taper screw plug.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


Hide 13511 3.INSTALL NO. 1 AND NO. 2 CAMSHAFTS

NOTICE:

If replacing a camshaft with a new one, make a matchmark on the new camshaft in the same place as the old camshaft. Determine the matchmark placement by using the dot mark as a reference point and counting the number of gear teeth from the dot mark to the matchmark as shown in the illustration.


A168355E05
2.25,0.979 2.771,1.5 2.771,1.5 2.771,1.625 true 1.552,0.625 1.896,0.281 1.896,0.281 2.042,0.281 true 2.344,1.656 3.063,1.823 0.719,0.167 10 false Matchmark 2.115,0.198 2.719,0.344 0.604,0.146 10 false Dot Mark 0.406,1.542 1.833,1.719 1.427,0.177 10 false Number of Gear Teeth

a.
A385652

Add more than 19 cc (1.16 cu. in.) of engine oil into the cylinder head side oil holes.


b.
A164816

Apply engine oil to the rollers of the valve rocker arms and the camshaft housing of the cylinder head.


c.

Install the No. 1 and No. 2 camshafts.

i.

Apply engine oil to the camshaft journals, lobes, thrust portion and gears.


ii.
A168400E07
1.74,1.271 2.354,0.188 2.354,0.188 1.885,1.271 true 2.365,0.188 2.5,0.188 false 2.573,0.104 3.292,0.25 0.719,0.146 10 false Matchmark

Align the matchmarks of the No. 1 and No. 2 camshaft timing gears as shown in the illustration.


iii.
A168345

Place the 2 camshafts into the cylinder head.

NOTICE:
A164641

Before and after setting the camshafts, firmly set the rocker arms to the lash adjusters.




d.
A168375

Install the No. 1 camshaft bearing cap.

i.

Align the No. 1 camshaft bearing cap and the ring pins of the No. 2 camshaft bearing cap.


ii.

Temporarily install the 4 bolts by hand.



e.
A168376

Install the No. 3 camshaft bearing caps.

i.

Confirm the marks and numbers on the camshaft bearing caps and place them in their proper position and direction.


ii.

Temporarily install the 8 bolts, which are not installed with the oil feed pipe, by hand.



f.
A168377

Temporarily install the No. 1 and No. 2 camshaft oil feed pipes with the 8 bolts by hand.

NOTICE:

If even one of the pipe bolt holes does not match its camshaft bearing cap bolt hole, replace the camshaft oil feed pipe.


HINT:

The pipe is bent on the intake side, and straight on the exhaust side.



g.
A168341

Temporarily install the 2 union bolts by hand.


h.
U163188E02
1.958,1.26 2.115,1.427 0.156,0.167 10 false 1 0.906,1.896 1.083,2.063 0.177,0.167 10 false 10 1.573,1.896 1.729,2.063 0.156,0.167 10 false 2 1.302,0.865 1.479,1.042 0.177,0.177 10 false 11 1.969,0.875 2.125,1.052 0.156,0.177 10 false 3 0.885,0.198 1.063,0.365 0.177,0.167 10 false 12 1.563,0.208 1.719,0.375 0.156,0.167 10 false 4 3.177,1.25 3.354,1.417 0.177,0.167 10 false 13 2.594,1.25 2.75,1.417 0.156,0.167 10 false 5 2.76,1.906 2.938,2.073 0.177,0.167 10 false 14 2.188,1.885 2.344,2.052 0.156,0.167 10 false 6 3.177,0.875 3.354,1.052 0.177,0.177 10 false 15 2.604,0.885 2.76,1.063 0.156,0.177 10 false 7 2.781,0.208 2.958,0.375 0.177,0.167 10 false 16 2.219,0.198 2.375,0.365 0.156,0.167 10 false 8 0.094,1.51 0.271,1.677 0.177,0.167 10 false 17 1.354,1.229 1.51,1.396 0.156,0.167 10 false 9 0.146,1.948 0.323,2.115 0.177,0.167 10 false 18 0.094,0.635 0.271,0.802 0.177,0.167 10 false 19 0.104,0.167 0.281,0.333 0.177,0.167 10 false 20 0.635,2.438 1.771,2.583 1.135,0.146 10 false 12 mm Head Bolt 0.635,2.896 1.75,3.042 1.115,0.146 10 false 10 mm Head Bolt

Uniformly tighten the 20 bolts in several steps in the order shown in the illustration.

Torque:
for 12 mm head bolt of No. 1 camshaft bearing cap : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for 10 mm head bolt of No. 3 camshaft bearing cap : 10 N*m (102 kgf*cm, 7 ft.*lbf)


i.
A168341

Tighten the 2 union bolts.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


j.
A164905

Remove the service bolt from the No. 1 camshaft timing gear.

NOTICE:

Do not drop the bolt into the engine.


HINT:

If the bolt is difficult to remove, rotate the camshaft and remove the bolt. Then realign the matchmarks of the No. 1 and No. 2 camshaft timing gears.



k.

Temporarily install the No. 1 timing chain and No. 1 camshaft timing sprocket to the No. 2 camshaft.


l.
A168367

Temporarily install the pump drive shaft gear with the 2 bolts.


m.
A168362E01
1.563,0.122 1.872,0.269 0.309,0.147 10 SST 1.507,0.205 0.626,0.205 false

Using SST, hold the pump drive shaft gear. Tighten the 2 bolts.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


n.

Rotate the crankshaft clockwise so that the 2 remaining pump drive shaft gear bolts can be installed.


o.
A168368

Temporarily install the 2 bolts to the pump drive shaft gear.


p.
A168362E01
1.563,0.122 1.872,0.269 0.309,0.147 10 SST 1.507,0.205 0.626,0.205 false

Using SST, hold the pump drive shaft gear. Tighten the 2 bolts.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


q.
A179133

Remove the hexagon wrench.


r.

Remove the adhesive from the threads of the taper screw plug and the bolt hole of the timing gear case.


s.
A168340

Apply adhesive to 3 or more threads of the taper screw plug.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



t.
A168310

Using a 10 mm hexagon wrench, install the taper screw plug.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


Hide 4.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Rotate the crankshaft clockwise 3 times or more, and check that the timing marks of the camshafts (1 dot mark each) align. If the timing marks of the camshafts do not align, repeat the "Install No. 3 and No. 4 Camshafts" and "Install No. 1 and No. 2 Camshafts" procedures.

A183917


Hide 11202 8.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 11201 12.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH

Hide 11225 14.INSTALL CYLINDER HEAD COVER SILENCER LH (w/ Intercooler)

Hide 11224 15.INSTALL CYLINDER HEAD COVER SILENCER RH (w/ Intercooler)

Hide 12263 16.CONNECT NO. 3 VENTILATION HOSE

Hide 12262 17.CONNECT NO. 2 VENTILATION HOSE

Hide 29300 18.INSTALL VACUUM PUMP ASSEMBLY (w/ Intercooler)

Hide 25706 19.INSTALL NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

Hide 25860 20.INSTALL NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (w/ Intercooler)

Hide 21.INSTALL NO. 2 IDLER PULLEY BRACKET (w/ Viscous Heater)

Hide 16630H 22.INSTALL NO. 2 IDLER PULLEY (w/ Viscous Heater)

Hide 23801L 25.INSTALL FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

Hide 23820A 26.INSTALL COMMON RAIL ASSEMBLY LH

Hide 23706 28.INSTALL NO. 6 INJECTION PIPE SUB-ASSEMBLY

Hide 30.CONNECT ENGINE WIRE

a.

RH side:

i.
U162980E02
1.313,2.813 1.469,2.979 0.156,0.167 10 false A 1.917,2.365 2.073,2.531 0.156,0.167 10 false A 2.594,1.292 2.75,1.458 0.156,0.167 10 false A 3.063,0.323 3.219,0.49 0.156,0.167 10 false B 1.417,0.802 1.573,0.969 0.156,0.167 10 false C

Install the engine wire harness protector with the 3 bolts labeled A.


ii.

Connect the 7 connectors.


iii.

Attach the wire harness clamp.


iv.

Install the wire harness bracket with the bolt labeled B.


v.

Install the glow plug wire harness with the nut labeled C.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


vi.
A174753

Attach the 5 wire harness clamps and connect the 4 connectors.



b.

LH side:

i.
U162981E02
0.813,1.542 0.969,1.708 0.156,0.167 10 false A 2.094,2.219 2.25,2.385 0.156,0.167 10 false B 1.375,1.708 1.531,1.875 0.156,0.167 10 false A 2.958,1.698 3.115,1.865 0.156,0.167 10 false C

Install the engine wire harness protector with the 2 bolts labeled A.


ii.

Connect the 8 connectors.


iii.

Install the wire harness bracket with the bolt labeled B.


iv.

for RHD:

Connect the wire harness with the wire harness clamp holder labeled C.


v.
A174755

Attach the 3 wire harness clamps and connect the 2 connectors.


vi.
A174754

Attach the 3 wire harness clamps and connect the 4 connectors.


vii.
U163800E02
1.969,1.521 2.094,1.667 0.125,0.146 10 false A 0.854,2.146 0.979,2.292 0.125,0.146 10 false B

Connect the wire harness with the wire harness clamp holder labeled B.


viii.

Attach the ground wire clamp labeled A to the relay block side.


ix.

Install the ground wire to the body panel with the bolt.

Torque:
8.4 N*m (87 kgf*cm, 74 in.*lbf)


x.
A365495

Connect the 4 connectors to the injector driver.


xi.

Install the ground wire with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


xii.

Connect the wire harness holder to the relay block.


xiii.

Connect the 2 connectors to the relay block.


xiv.

Connect the wire harness with the wire harness clamp holder.



c.
A174759

for RHD:

i.

Connect the wire harness with the wire harness clamp holder.


ii.
U163799E01
2.277,1.881 2.398,2.026 0.121,0.145 10 A

Connect the ECM connector to the ECM.


iii.

Connect the wire harness with the wire harness clamp holder.


iv.

Attach the wire harness tab labeled A to the relay block.


v.

Connect the 4 connectors to the relay block.



d.
U163798E02
1.479,1.948 1.604,2.094 0.125,0.146 10 false A

for LHD:

i.

Connect the wire harness with the wire harness clamp holder.


ii.

Connect the ECM connector to the ECM.


iii.

Attach the wire harness tab labeled A to the relay block.


iv.

Connect the 4 connectors to the relay block.



Hide 23274D 31.CONNECT FUEL HOSE

Hide 16268M 33.INSTALL NO. 3 WATER BY-PASS PIPE (w/o Viscous Heater)

Hide 31489 34.INSTALL TUBE CONNECTOR TO FLEXIBLE HOSE TUBE (for Manual Transaxle)

Hide 31418 36.INSTALL CLUTCH HOSE (for Manual Transmission)

Hide 87209 39.CONNECT WATER HOSE SUB-ASSEMBLY

Hide 17806 40.INSTALL NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY

Hide 17885 43.INSTALL NO. 1 AIR CLEANER PIPE SUB-ASSEMBLY

Hide 46.INSTALL NO. 1 IDLER PULLEY BRACKET (w/ Viscous Heater)

Hide 87120G 47.INSTALL VISCOUS HEATER ASSEMBLY WITH MAGNET CLUTCH (w/ Viscous Heater)

Hide 87208 48.INSTALL HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)

Hide 17973 49.INSTALL NO. 2 COOL AIR INLET (w/o Intercooler)

Hide 17973 50.INSTALL NO. 1 COOL AIR INLET (w/o Intercooler)

Hide 17940D 51.INSTALL INTERCOOLER ASSEMBLY (w/ Intercooler)

Hide 32942 53.INSTALL OIL COOLER TUBE (for Automatic Transmission)

Hide 55.INSTALL NO. 3 IDLER PULLEY (w/ Viscous Heater)

Hide 56.INSTALL NO. 1 IDLER PULLEY (w/ Viscous Heater)

Hide 16470 59.INSTALL RADIATOR RESERVOIR ASSEMBLY

Hide 44369A 60.INSTALL NO. 1 OIL RESERVOIR BRACKET

Hide 44360 61.INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 17881 63.TEMPORARILY INSTALL NO. 1 AIR CLEANER HOSE

Hide 69.INSPECT FOR CLUTCH FLUID LEAK

Hide 28800N 70.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


a.

Connect the cables to negative (-) main battery and sub-battery battery terminals.


Hide 73.INSPECT FOR OIL LEAK

Hide 75.WARM UP ENGINE

NOTICE:

In order to bleed air from the chain tensioner, drive the vehicle with the engine at 3000 rpm for 60 seconds or more.


Hide 76.INSPECT FOR EXHAUST GAS LEAK

Hide 51405A 77.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 53805 78.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 53806 79.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53737B 81.INSTALL FRONT FENDER APRON SEAL FRONT LH

Hide 53736G 83.INSTALL FRONT FENDER APRON SEAL FRONT RH

Hide 12601E 84.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Intercooler)

Hide 55781E 85.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53882H 89.INSTALL FRONT FENDER MAIN SEAL RH

Hide 53883F 90.INSTALL FRONT FENDER MAIN SEAL LH

Hide 53292A 91.INSTALL UPPER RADIATOR SUPPORT SEAL