Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › CAMSHAFT (w/o DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052779 1VD-FTV ENGINE MECHANICAL _0255066 CAMSHAFT(w/o DPF) A

1VD-FTV ENGINE MECHANICAL  CAMSHAFT(w/o DPF)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

When replacing an injector (including interchanging injectors between cylinders), common rail, cylinder head, or intake manifold, replace the corresponding injection pipes with a new one.


PROCEDURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 5.DRAIN CLUTCH FLUID (for Manual Transmission)

Hide 53806 6.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 7.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 51405A 8.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 53292A 10.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 82113 11.REMOVE NO. 3 ENGINE ROOM WIRE

Hide 12601E 12.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Intercooler)

Hide 16.REMOVE V-RIBBED BELT (w/ Viscous Heater)

Hide 17.REMOVE NO. 1 IDLER PULLEY (w/ Viscous Heater)

Hide 18.REMOVE NO. 3 IDLER PULLEY (w/ Viscous Heater)

Hide 53736G 20.REMOVE FRONT FENDER APRON SEAL FRONT RH

Hide 53738A 21.REMOVE FRONT FENDER APRON SEAL REAR RH

Hide 53737B 22.REMOVE FRONT FENDER APRON SEAL FRONT LH

Hide 53739A 23.REMOVE FRONT FENDER APRON SEAL REAR LH

Hide 44360 24.REMOVE VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 44369A 25.REMOVE NO. 1 OIL RESERVOIR BRACKET

Hide 16470 26.REMOVE RADIATOR RESERVOIR ASSEMBLY

Hide 32942 28.REMOVE OIL COOLER TUBE (for Automatic Transmission)

Hide 53883F 30.REMOVE FRONT FENDER MAIN SEAL LH

Hide 53882H 31.REMOVE FRONT FENDER MAIN SEAL RH

Hide 85221B 32.REMOVE FRONT WIPER ARM LH

Hide 85211B 33.REMOVE FRONT WIPER ARM RH

Hide 53383 34.REMOVE HOOD TO COWL TOP SEAL

Hide 55781E 35.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 17940D 36.REMOVE INTERCOOLER ASSEMBLY (w/ Intercooler)

Hide 17973 37.REMOVE NO. 1 COOL AIR INLET (w/o Intercooler)

Hide 17973 38.REMOVE NO. 2 COOL AIR INLET (w/o Intercooler)

Hide 41.REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 31418 43.REMOVE CLUTCH HOSE (for Manual Transmission)

Hide 31489 45.REMOVE TUBE CONNECTOR TO FLEXIBLE HOSE TUBE (for Manual Transmission)

Hide 16268M 47.REMOVE NO. 3 WATER BY-PASS PIPE (w/o Viscous Heater)

Hide 87208 48.REMOVE HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)

Hide 17885 50.REMOVE NO. 1 AIR CLEANER PIPE SUB-ASSEMBLY

Hide 17806 52.REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY

Hide 87120G 53.REMOVE VISCOUS HEATER ASSEMBLY WITH MAGNET CLUTCH (w/ Viscous Heater)

Hide 54.REMOVE NO. 1 IDLER PULLEY BRACKET (w/ Viscous Heater)

Hide 57.DISCONNECT ENGINE WIRE

a.

LH Side:

i.
A365495

Disconnect the 4 connectors from the injector driver.


ii.

Remove the 2 connectors and detach the wire harness holder from the relay block.


iii.

Remove the bolt and disconnect the ground wire.


iv.

Disconnect the wire harness from the wire harness clamp holder.


v.
U163800E02
1.969,1.521 2.094,1.667 0.125,0.146 10 false A 0.854,2.146 0.979,2.292 0.125,0.146 10 false B

Remove the bolt and disconnect the ground wire from the body panel.


vi.

Using a clip remover, detach the ground wire clamp labeled A from the relay block side.


vii.

Disconnect the wire harness from the wire harness clamp holder labeled B.


viii.
A174754

Disconnect the 4 connectors.


ix.

Using a clip remover, detach the 3 wire harness clamps.


x.
A174755

Disconnect the 2 connectors.


xi.

Using a clip remover, detach the 3 wire harness clamps.


xii.
U162981E02
0.813,1.542 0.969,1.708 0.156,0.167 10 false A 2.094,2.219 2.25,2.385 0.156,0.167 10 false B 1.375,1.708 1.531,1.875 0.156,0.167 10 false A 2.958,1.698 3.115,1.865 0.156,0.167 10 false C

Disconnect the 8 connectors.


xiii.

Remove the 2 bolts labeled A and disconnect the engine wire protector.


xiv.

Remove the bolt labeled B and engine wire harness bracket.


xv.

for RHD:

Disconnect the wire harness from the wire harness clamp holder labeled C.



b.

RH Side:

i.
A174753

Disconnect the 4 connectors.


ii.

Using a clip remover, detach the 5 wire harness clamps.


iii.
U162980E02
1.313,2.813 1.469,2.979 0.156,0.167 10 false A 1.917,2.365 2.073,2.531 0.156,0.167 10 false A 2.594,1.292 2.75,1.458 0.156,0.167 10 false A 3.063,0.323 3.219,0.49 0.156,0.167 10 false B 1.417,0.802 1.573,0.969 0.156,0.167 10 false C

Disconnect the 7 connectors.


iv.

Using a clip remover, detach the wire harness clamp.


v.

Remove the 3 bolts labeled A and disconnect the wire harness protector.


vi.

Remove the bolt labeled B and wire harness bracket.


vii.

Remove the nut labeled C and glow plug wire harness.



c.
U163798E01
1.541,1.883 1.662,2.028 0.121,0.145 10 A

for LHD:

i.

Disconnect the 4 connectors, and detach the wire harness tab labeled A from the relay block.


ii.

Disconnect the ECM connector.


iii.

Disconnect the wire harness from the wire harness clamp holder.



d.

for RHD:

i.
A174759

Disconnect the wire harness from the wire harness clamp holder.


ii.
U163799E02
2.219,1.948 2.344,2.094 0.125,0.146 10 false A

Disconnect the 4 connectors, and detach the wire harness tab labeled A from the relay block.


iii.

Disconnect the ECM connector.


iv.

Disconnect the wire harness from the wire harness clamp holder.



Hide 23706 59.REMOVE NO. 6 INJECTION PIPE SUB-ASSEMBLY

Hide 23820A 61.REMOVE COMMON RAIL ASSEMBLY LH

Hide 23801L 62.REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

Hide 16630H 65.REMOVE NO. 2 IDLER PULLEY (w/ Viscous Heater)

Hide 66.REMOVE NO. 2 IDLER PULLEY BRACKET (w/ Viscous Heater)

Hide 25860 67.REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (w/ Intercooler)

Hide 25706 68.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

Hide 29300 69.REMOVE VACUUM PUMP ASSEMBLY (w/ Intercooler)

Hide 11224 72.REMOVE CYLINDER HEAD COVER SILENCER RH (w/ Intercooler)

Hide 11225 73.REMOVE CYLINDER HEAD COVER SILENCER LH (w/ Intercooler)

Hide 11201 75.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH

Hide 11202 79.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 13511 83.REMOVE NO. 1 AND NO. 2 CAMSHAFTS

a.
A168309E06
1.417,0.385 0.656,0.385 true 0.25,0.302 0.646,0.458 0.396,0.156 10 false Arrow

Rotate the crankshaft clockwise, and align the No. 1 camshaft timing sprocket arrow with the cylinder head upper surface.


b.
A168310

Using a 10 mm hexagon wrench, remove the taper screw plug.


c.

Fix the No. 1 chain tensioner in place.

i.

Push the tensioner slipper away from the tensioner, and move the stopper plate clockwise to release the lock as shown in A.


ii.

Push down the tensioner slipper and move the stopper plate counterclockwise to set the lock as shown in B.


iii.

Push the tensioner slipper away from the tensioner, and insert a hexagon wrench into the stopper plate hole as shown in C.

NOTICE:

Do not drop the hexagon wrench into the engine.


U163081E02
0.708,1.667 0.708,2.323 true 2.563,0.417 2.719,0.583 0.156,0.167 10 false A 4.458,0.417 4.615,0.583 0.156,0.167 10 false B 6.354,0.417 6.51,0.583 0.156,0.167 10 false C 0.323,2.365 1.188,2.542 0.865,0.177 10 false Stopper Plate



d.
A168361E01
0.525,0.993 0.820,1.140 0.295,0.146 10 SST 0.695,0.458 0.695,0.972 false

Using SST, hold the pump drive shaft gear.

SST
09960-10010  (09962-01000, 09963-01000)


e.

Remove the 2 bolts.


f.
A168312E07
1.615,1.323 1.469,1.323 1.469,1.323 1.104,1.021 true 1.688,1.24 2.083,1.385 0.396,0.146 10 false Arrow

Rotate the crankshaft clockwise 360° so that the No. 1 camshaft timing sprocket arrow points at the No. 1 camshaft center.

NOTICE:

Do not rotate the crankshaft counterclockwise in order to align the sprocket arrow and camshaft center.



g.
A168313E07
1.49,0.563 2.313,0.281 2.313,0.281 1.573,0.458 true 1.729,1.271 2.292,0.271 2.292,0.271 1.854,1.271 true 2.281,0.281 2.448,0.281 false 2.51,0.208 3.25,0.365 0.74,0.156 10 false Matchmark

Place matchmarks on the No. 1 timing chain and No. 1 camshaft timing sprocket.


h.

Place matchmarks on the No. 1 and No. 2 camshaft gears.


i.
A168362E01
1.563,0.122 1.872,0.269 0.309,0.147 10 SST 1.507,0.205 0.626,0.205 false

Using SST, hold the pump drive shaft gear.

SST
09960-10010  (09962-01000, 09963-01000)


j.

Remove the 2 bolts and pump drive shaft gear.


k.

Disconnect the No. 1 timing chain and No. 1 camshaft timing sprocket from the No. 2 camshaft.

NOTICE:
·

Do not remove the No. 1 camshaft timing sprocket from the No. 1 timing chain.

·

Do not rotate the crankshaft until the No. 1 timing chain and No. 1 camshaft timing sprocket are connected to the No. 2 camshaft.



HINT:

If fixing the No. 1 camshaft timing sprocket in place, pass a rope or equivalent through one of the No. 1 camshaft timing sprocket holes and tie the sprocket and chain together.



l.
A168387

Turn the No. 1 camshaft clockwise so that the bolt is easier to install.


m.
A168363

Using a 6 mm x 1.0 pitch service bolt with a length of 16 mm or more, fix the No. 1 camshaft in place.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Do not drop the bolt into the engine.


HINT:

If it is difficult to install the bolt, rotate the camshaft so that the bolt is easier to install.



n.
A168341

Loosen the 2 union bolts.


o.
U162957E02
0.344,0.313 0.5,0.479 0.156,0.167 10 false 1 1.344,0.906 1.521,1.083 0.177,0.177 10 false 10 0.354,0.719 0.51,0.885 0.156,0.167 10 false 2 0.958,1.917 1.135,2.083 0.177,0.167 10 false 11 0.479,1.927 0.635,2.094 0.156,0.167 10 false 3 1.333,1.26 1.51,1.427 0.177,0.167 10 false 12 0.354,1.427 0.51,1.594 0.156,0.167 10 false 4 2.125,0.208 2.302,0.375 0.177,0.167 10 false 13 3.177,0.646 3.333,0.813 0.156,0.167 10 false 5 2.531,0.896 2.708,1.073 0.177,0.177 10 false 14 3.177,0.906 3.333,1.083 0.156,0.177 10 false 6 2.115,1.917 2.292,2.083 0.177,0.167 10 false 15 3.177,1.479 3.333,1.646 0.156,0.167 10 false 7 2.521,1.26 2.698,1.427 0.177,0.167 10 false 16 3.177,1.24 3.333,1.406 0.156,0.167 10 false 8 1.51,0.208 1.688,0.375 0.177,0.167 10 false 17 0.969,0.208 1.125,0.375 0.156,0.167 10 false 9 1.927,0.896 2.104,1.063 0.177,0.167 10 false 18 1.542,1.917 1.719,2.083 0.177,0.167 10 false 19 1.938,1.25 2.115,1.417 0.177,0.167 10 false 20

Uniformly loosen and remove the 20 bolts in the sequence shown in the illustration.


p.
A168343

Remove the 2 union bolts and No. 1 and No. 2 oil feed pipes.


q.
A168344

Remove the 8 No. 3 camshaft bearing caps and No. 1 camshaft bearing cap.

HINT:

Be sure to arrange the removed parts for each installation position separately.



r.
A168345

Remove the No. 1 and No. 2 camshafts.


Hide 13053 84.REMOVE NO. 3 AND NO. 4 CAMSHAFTS

a.
A168319

Rotate the crankshaft clockwise, and align the No. 2 camshaft timing sprocket arrow with the cylinder head upper surface.


b.
A168320

Using a 10 mm hexagon wrench, remove the taper screw plug.


c.

Fix the No. 2 chain tensioner in place.

i.

Push the tensioner slipper away from the tensioner, and move the stopper plate clockwise to release the lock as shown in A.


ii.

Push up the tensioner slipper and move the stopper plate counterclockwise to set the lock as shown in B.


iii.

Push the tensioner slipper away from the tensioner, and insert a hexagon wrench into the stopper plate hole as shown in C.

NOTICE:

Do not drop the hexagon wrench into the engine.


U163083E02
0.833,1.563 0.833,2.354 true 2.604,0.385 2.76,0.552 0.156,0.167 10 false A 4.417,0.396 4.573,0.563 0.156,0.167 10 false B 6.219,0.385 6.375,0.552 0.156,0.167 10 false C 0.427,2.406 1.292,2.583 0.865,0.177 10 false Stopper Plate



d.
A168364E03
2.712,0.759 3.012,0.918 0.299,0.158 10 SST 2.378,0.174 2.88,0.547 2.88,0.547 2.88,0.717 false

Using SST, hold the No. 2 camshaft timing sprocket.

SST
09960-10010  (09962-01000, 09963-01000)


e.

Remove the 2 bolts.


f.
A168322E06
2.365,0.906 1.677,1.146 1.677,1.146 1.677,1.271 true 1.51,1.302 1.896,1.458 0.385,0.156 10 false Arrow

Rotate the crankshaft clockwise 360° so that the No. 2 camshaft timing sprocket arrow points at the No. 4 camshaft center.


g.
A168323E06
1.583,1.333 1.031,0.146 1.031,0.146 1.74,1.333 true 1.969,0.438 1.01,0.146 1.01,0.146 2.063,0.563 true 1.031,0.146 0.938,0.146 false 0.198,0.063 0.927,0.229 0.729,0.167 10 false Matchmark

Place matchmarks on the No. 2 timing chain and No. 2 camshaft timing sprocket.


h.

Place matchmarks on the No. 3 and No. 4 camshaft gears.


i.
A168364E03
2.712,0.759 3.012,0.918 0.299,0.158 10 SST 2.378,0.174 2.88,0.547 2.88,0.547 2.88,0.717 false

Using SST, hold the No. 2 camshaft timing sprocket.

SST
09960-10010  (09962-01000, 09963-01000)


j.

Remove the 2 bolts, and disconnect the No. 2 timing chain and No. 2 camshaft timing sprocket from the No. 3 camshaft.

NOTICE:
·

Do not remove the No. 2 camshaft timing sprocket from the No. 2 timing chain.

·

Do not rotate the crankshaft until the No. 2 timing chain and No. 2 camshaft timing sprocket are connected to the No. 3 camshaft.



HINT:

If fixing the No. 2 camshaft timing sprocket in place, pass a rope or equivalent through one of the No. 2 camshaft timing sprocket holes and tie the sprocket and chain together.



k.
A168365

Using a 6 mm x 1.0 pitch service bolt with a length of 16 mm or more, fix the No. 4 camshaft in place.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Do not drop the bolt into the chain cover.


HINT:

If it is difficult to install the bolt, rotate the camshaft so that the bolt is easier to install.



l.
A168346

Loosen the 2 union bolts.


m.
U162958E02
0.25,0.271 0.406,0.438 0.156,0.167 10 false 1 1.458,0.854 1.635,1.031 0.177,0.177 10 false 10 0.25,0.74 0.406,0.906 0.156,0.167 10 false 2 1.073,1.854 1.25,2.021 0.177,0.167 10 false 11 0.375,1.865 0.531,2.031 0.156,0.167 10 false 3 1.458,1.208 1.635,1.375 0.177,0.167 10 false 12 0.25,1.375 0.406,1.542 0.156,0.167 10 false 4 2.26,0.208 2.438,0.375 0.177,0.167 10 false 13 3.25,0.635 3.406,0.802 0.156,0.167 10 false 5 2.615,0.833 2.792,1 0.177,0.167 10 false 14 3.25,0.896 3.406,1.063 0.156,0.167 10 false 6 2.24,1.854 2.417,2.021 0.177,0.167 10 false 15 3.26,1.427 3.417,1.594 0.156,0.167 10 false 7 2.615,1.198 2.792,1.365 0.177,0.167 10 false 16 3.25,1.198 3.406,1.365 0.156,0.167 10 false 8 1.635,0.208 1.813,0.375 0.177,0.167 10 false 17 1.094,0.208 1.25,0.375 0.156,0.167 10 false 9 2.042,0.854 2.219,1.021 0.177,0.167 10 false 18 1.656,1.854 1.833,2.021 0.177,0.167 10 false 19 2.042,1.208 2.219,1.375 0.177,0.167 10 false 20

Uniformly loosen and remove the 20 bolts in the sequence shown in the illustration.


n.
A168348

Remove the 2 union bolts and No. 3 and No. 4 oil feed pipes.


o.
A168378

Remove the 8 No. 3 camshaft bearing caps and No. 4 camshaft bearing cap.

HINT:

Be sure to arrange the removed parts for each installation position separately.



p.
A168350

Remove the No. 3 and No. 4 camshafts.