When replacing an injector (including interchanging injectors between cylinders), common rail, cylinder head, or intake manifold, replace the corresponding injection pipes with a new one.
When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.
1.CHECK INJECTOR COMPENSATION CODE
2. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
55781E
4.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
5.DRAIN ENGINE OIL
6.REMOVE FRONT WHEEL
53806
7.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
53805
8.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
51405A
9.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
10.DRAIN ENGINE COOLANT
53292A
11.REMOVE UPPER RADIATOR SUPPORT SEAL
82113
12.REMOVE NO. 3 ENGINE ROOM WIRE
12601E
13.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY
17705
14.REMOVE AIR CLEANER CAP SUB-ASSEMBLY
17881
15.REMOVE NO. 1 AIR CLEANER HOSE
17861
16.REMOVE INTAKE AIR CONNECTOR
17.REMOVE V-RIBBED BELT (w/ Viscous Heater)
18.REMOVE NO. 1 IDLER PULLEY (w/ Viscous Heater)
19.REMOVE NO. 3 IDLER PULLEY (w/ Viscous Heater)
16361A
20.REMOVE V-RIBBED BELT
53782
21.REMOVE FRONT FENDER APRON SEAL FRONT RH
53784
22.REMOVE FRONT FENDER APRON SEAL REAR RH
53783
23.REMOVE FRONT FENDER APRON SEAL FRONT LH
53785B
24.REMOVE FRONT FENDER APRON SEAL REAR LH
44360
25.REMOVE VANE PUMP OIL RESERVOIR ASSEMBLY
44369A
26.REMOVE NO. 1 OIL RESERVOIR BRACKET
16470
27.REMOVE RADIATOR RESERVOIR ASSEMBLY
44310
28.REMOVE VANE PUMP ASSEMBLY
32942
29.REMOVE OIL COOLER TUBE
16711
30.REMOVE FAN SHROUD WITH FAN
17940D
31.REMOVE INTERCOOLER ASSEMBLY
17341F
32.REMOVE NO. 1 AIR HOSE
17342D
33.REMOVE NO. 2 AIR HOSE
34.REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE
17971
35.REMOVE AIR TUBE SUB-ASSEMBLY RH
17972
36.REMOVE AIR TUBE SUB-ASSEMBLY LH
87209
37.DISCONNECT WATER HOSE SUB-ASSEMBLY
16268M
38.REMOVE NO. 3 WATER BY-PASS PIPE (w/o Viscous Heater)
87208
39.REMOVE HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)
17363K
40.REMOVE NO. 3 AIR TUBE
17885
41.REMOVE NO. 1 AIR CLEANER PIPE SUB-ASSEMBLY
17364
42.REMOVE NO. 4 AIR TUBE
17806
43.REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY
87120G
44.REMOVE VISCOUS HEATER ASSEMBLY WITH MAGNET CLUTCH (w/ Viscous Heater)
45.REMOVE NO. 1 IDLER PULLEY BRACKET (w/ Viscous Heater)
16288
46.REMOVE NO. 4 WATER BY-PASS PIPE
23274D
47.DISCONNECT FUEL HOSE
48.DISCONNECT ENGINE WIRE
LH Side:
Disconnect the 7 connectors from the injector driver.
Remove the 4 connectors and detach the wire harness holder from the relay block.
Remove the bolt and disconnect the ground wire.
Disconnect the wire harness from the wire harness clamp holder.
Remove the bolt and disconnect the ground wire from the body panel.
Using a clip remover, detach the ground wire clamp from the relay block side labeled A.
Disconnect the wire harness from the wire harness clamp holder labeled B.
Disconnect the 4 connectors.
Using a clip remover, detach the 3 wire harness clamps.
Disconnect the 2 connectors.
Using a clip remover, detach the 3 wire harness clamps.
Disconnect the 8 connectors.
Remove the bolt and engine wire harness bracket labeled B.
Using a clip remover, detach the wire harness clamp labeled D.
Remove the 2 bolts and disconnect the engine wire protector labeled A.
for RHD:
Disconnect the wire harness from the wire harness clamp holder labeled C.
RH Side:
Disconnect the 4 connectors.
Using a clip remover, detach the 5 wire harness clamps.
Disconnect the 7 connectors.
Using a clip remover, detach the wire harness clamp.
Remove the 3 bolts and disconnect the wire harness protector labeled A.
Remove the bolt and wire harness bracket labeled B.
Remove the nut and glow plug wire harness labeled C.
for LHD:
Disconnect the 4 connectors, and detach the wire harness tab from the relay block labeled A.
Disconnect the ECM connector.
Disconnect the wire harness from the wire harness clamp holder.
for RHD:
Disconnect the wire harness from the wire harness clamp holder.
Remove the bolt and wire harness clamp holder.
Disconnect the 4 connectors, and detach the wire harness tab from the relay block labeled A.
Disconnect the ECM connector.
Disconnect the wire harness from the wire harness clamp holder.
23706
49.REMOVE NO. 6 INJECTION PIPE SUB-ASSEMBLY
25860
50.REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY
25706
51.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY
11225
52.REMOVE CYLINDER HEAD COVER SILENCER LH
23764A
53.REMOVE NO. 4 NOZZLE LEAKAGE PIPE
23701
54.REMOVE INJECTION PIPE LH
23812D
55.REMOVE NO. 2 FUEL PIPE
23765
56.REMOVE NO. 5 NOZZLE LEAKAGE PIPE
23820A
57.REMOVE COMMON RAIL ASSEMBLY LH
23801L
58.REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY
59.DISCONNECT NO. 2 ENGINE WIRE
11224
60.REMOVE CYLINDER HEAD COVER SILENCER RH
23702
61.REMOVE INJECTION PIPE RH
16630H
62.REMOVE NO. 2 IDLER PULLEY (w/ Viscous Heater)
63.REMOVE NO. 2 IDLER PULLEY BRACKET (w/ Viscous Heater)
29300
64.REMOVE VACUUM PUMP ASSEMBLY
27148B
65.REMOVE CONNECTING WIRE
23763
66.REMOVE NO. 3 NOZZLE LEAKAGE PIPE
11227
67.REMOVE CYLINDER HEAD COVER INSULATOR RH
12262
68.REMOVE NO. 2 VENTILATION HOSE
23711
69.REMOVE NO. 1 FUEL INJECTOR PROTECTOR
23761A
70.REMOVE NO. 1 NOZZLE LEAKAGE PIPE
23670
71.REMOVE FUEL INJECTOR RH
11201
72.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH
73.REMOVE NO. 2 FUEL PUMP BRACKET
11228A
74.REMOVE CYLINDER HEAD COVER INSULATOR LH
12263
75.REMOVE NO. 3 VENTILATION HOSE
76.REMOVE BREATHER PLUG LH
23712
77.REMOVE NO. 2 FUEL INJECTOR PROTECTOR
23762B
78.REMOVE NO. 2 NOZZLE LEAKAGE PIPE
23670
79.REMOVE FUEL INJECTOR LH
12270
80.REMOVE OIL SEPARATOR ASSEMBLY
11202
81.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH
13511
82.REMOVE NO. 1 AND NO. 2 CAMSHAFTS
Rotate the crankshaft clockwise, and align the No. 1 camshaft timing sprocket arrow with the cylinder head upper surface.
| *1 | Arrow |
Using a 10 mm hexagon wrench, remove the taper screw plug.
Fix the No. 1 chain tensioner in place.
Push the tensioner slipper away from the tensioner, and move the stopper plate clockwise to release the lock as shown in A.
Push down the tensioner slipper and move the stopper plate counterclockwise to set the lock as shown in B.
Push the tensioner slipper away from the tensioner, and insert a hexagon wrench into the stopper plate hole as shown in C.
Do not drop the hexagon wrench into the engine.
| *1 | Stopper Plate | - | - |
Using SST, hold the pump drive shaft gear.
Remove the 2 bolts.
Rotate the crankshaft clockwise 360° so that the No. 1 camshaft timing sprocket arrow points at the No. 1 camshaft center.
| *1 | Arrow |
Do not rotate the crankshaft counterclockwise in order to align the sprocket arrow and camshaft center.
Place matchmarks on the No. 1 timing chain and No. 1 camshaft timing sprocket.
| *1 | Matchmark |
Place matchmarks on the No. 1 and No. 2 camshaft gears.
Using SST, hold the pump drive shaft gear.
Remove the 2 bolts and pump drive shaft gear.
Disconnect the No. 1 timing chain and No. 1 camshaft timing sprocket from the No. 2 camshaft.
Do not remove the No. 1 camshaft timing sprocket from the No. 1 timing chain.
Do not rotate the crankshaft until the No. 1 timing chain and No. 1 camshaft timing sprocket are connected to the No. 2 camshaft.
If fixing the No. 1 camshaft timing sprocket in place, pass a rope or equivalent through one of the No. 1 camshaft timing sprocket holes and tie the sprocket and chain together.
Turn the No. 1 camshaft clockwise so that the bolt is easier to install.
Using a 6 mm x 1.0 pitch service bolt with a length of 16 mm or more, fix the No. 1 camshaft in place.
Do not drop the bolt into the engine.
If it is difficult to install the bolt, rotate the camshaft so that the bolt is easier to install.
Loosen the 2 union bolts.
Uniformly loosen and remove the 20 bolts in the sequence shown in the illustration.
Remove the 2 union bolts and No. 1 and No. 2 oil feed pipes.
Remove the 8 No. 3 camshaft bearing caps and No. 1 camshaft bearing cap.
Be sure to arrange the removed parts for each installation position separately.
Remove the No. 1 and No. 2 camshafts.
13053
83.REMOVE NO. 3 AND NO. 4 CAMSHAFTS
Rotate the crankshaft clockwise, and align the No. 2 camshaft timing sprocket arrow with the cylinder head upper surface.
| *1 | Arrow |
Using a 10 mm hexagon wrench, remove the taper screw plug.
Fix the No. 2 chain tensioner in place.
Push the tensioner slipper away from the tensioner, and move the stopper plate clockwise to release the lock as shown in A.
Push up the tensioner slipper and move the stopper plate counterclockwise to set the lock as shown in B.
Push the tensioner slipper away from the tensioner, and insert a hexagon wrench into the stopper plate hole as shown in C.
Do not drop the hexagon wrench into the engine.
| *1 | Stopper Plate | - | - |
Using SST, hold the No. 2 camshaft timing sprocket.
Remove the 2 bolts.
Rotate the crankshaft clockwise 360° so that the No. 2 camshaft timing sprocket arrow points at the No. 4 camshaft center.
| *1 | Arrow |
Place matchmarks on the No. 2 timing chain and No. 2 camshaft timing sprocket.
| *1 | Matchmark |
Place matchmarks on the No. 3 and No. 4 camshaft gears.
Using SST, hold the No. 2 camshaft timing sprocket.
Remove the 2 bolts, and disconnect the No. 2 timing chain and No. 2 camshaft timing sprocket from the No. 3 camshaft.
Do not remove the No. 2 camshaft timing sprocket from the No. 2 timing chain.
Do not rotate the crankshaft until the No. 2 timing chain and No. 2 camshaft timing sprocket are connected to the No. 3 camshaft.
If fixing the No. 2 camshaft timing sprocket in place, pass a rope or equivalent through one of the No. 2 camshaft timing sprocket holes and tie the sprocket and chain together.
Using a 6 mm x 1.0 pitch service bolt with a length of 16 mm or more, fix the No. 4 camshaft in place.
Do not drop the bolt into the chain cover.
If it is difficult to install the bolt, rotate the camshaft so that the bolt is easier to install.
Loosen the 2 union bolts.
Uniformly loosen and remove the 20 bolts in the sequence shown in the illustration.
Remove the 2 union bolts and No. 3 and No. 4 oil feed pipes.
Remove the 8 No. 3 camshaft bearing caps and No. 4 camshaft bearing cap.
Be sure to arrange the removed parts for each installation position separately.
Remove the No. 3 and No. 4 camshafts.