Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › CAMSHAFT (w/ DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052779 1VD-FTV ENGINE MECHANICAL _0255073 CAMSHAFT(w/ DPF) A

1VD-FTV ENGINE MECHANICAL  CAMSHAFT(w/ DPF)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

When replacing an injector (including interchanging injectors between cylinders), common rail, cylinder head, or intake manifold, replace the corresponding injection pipes with a new one.


NOTICE:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.


PROCEDURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 55781E 4.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53806 6.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 7.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 51405A 8.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 53292A 10.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 82113 11.REMOVE NO. 3 ENGINE ROOM WIRE

Hide 12601E 12.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 16.REMOVE V-RIBBED BELT (w/ Viscous Heater)

Hide 17.REMOVE NO. 1 IDLER PULLEY (w/ Viscous Heater)

Hide 18.REMOVE NO. 3 IDLER PULLEY (w/ Viscous Heater)

Hide 53782 20.REMOVE FRONT FENDER APRON SEAL FRONT RH

Hide 53784 21.REMOVE FRONT FENDER APRON SEAL REAR RH

Hide 53783 22.REMOVE FRONT FENDER APRON SEAL FRONT LH

Hide 53785B 23.REMOVE FRONT FENDER APRON SEAL REAR LH

Hide 44360 24.REMOVE VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 44369A 25.REMOVE NO. 1 OIL RESERVOIR BRACKET

Hide 16470 26.REMOVE RADIATOR RESERVOIR ASSEMBLY

Hide 33.REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 16268M 37.REMOVE NO. 3 WATER BY-PASS PIPE (w/o Viscous Heater)

Hide 87208 38.REMOVE HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)

Hide 17885 40.REMOVE NO. 1 AIR CLEANER PIPE SUB-ASSEMBLY

Hide 17806 42.REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY

Hide 87120G 43.REMOVE VISCOUS HEATER ASSEMBLY WITH MAGNET CLUTCH (w/ Viscous Heater)

Hide 44.REMOVE NO. 1 IDLER PULLEY BRACKET (w/ Viscous Heater)

Hide 47.DISCONNECT ENGINE WIRE

a.

LH Side:

i.
A271632

Disconnect the 7 connectors from the injector driver.


ii.

Remove the 4 connectors and detach the wire harness holder from the relay block.


iii.

Remove the bolt and disconnect the ground wire.


iv.

Disconnect the wire harness from the wire harness clamp holder.


v.
U163800E02
1.969,1.521 2.094,1.667 0.125,0.146 10 false A 0.854,2.146 0.979,2.292 0.125,0.146 10 false B

Remove the bolt and disconnect the ground wire from the body panel.


vi.

Using a clip remover, detach the ground wire clamp from the relay block side labeled A.


vii.

Disconnect the wire harness from the wire harness clamp holder labeled B.


viii.
A174754

Disconnect the 4 connectors.


ix.

Using a clip remover, detach the 3 wire harness clamps.


x.
A174755

Disconnect the 2 connectors.


xi.

Using a clip remover, detach the 3 wire harness clamps.


xii.
U163637E02
0.76,1.802 0.885,1.948 0.125,0.146 10 false A 2.292,2.823 2.417,2.969 0.125,0.146 10 false B 2.771,1.969 2.896,2.115 0.125,0.146 10 false C 1.646,1.688 1.771,1.833 0.125,0.146 10 false A 1.146,2.26 1.271,2.406 0.125,0.146 10 false D

Disconnect the 8 connectors.


xiii.

Remove the bolt and engine wire harness bracket labeled B.


xiv.

Using a clip remover, detach the wire harness clamp labeled D.


xv.

Remove the 2 bolts and disconnect the engine wire protector labeled A.


xvi.

for RHD:

Disconnect the wire harness from the wire harness clamp holder labeled C.



b.

RH Side:

i.
A174753

Disconnect the 4 connectors.


ii.

Using a clip remover, detach the 5 wire harness clamps.


iii.
U163638E02
1.083,2.021 1.208,2.167 0.125,0.146 10 false A 2.958,1.25 3.083,1.396 0.125,0.146 10 false B 1.573,0.563 1.698,0.708 0.125,0.146 10 false C 1.271,1.729 1.396,1.875 0.125,0.146 10 false A 3.01,0.635 3.135,0.781 0.125,0.146 10 false A

Disconnect the 7 connectors.


iv.

Using a clip remover, detach the wire harness clamp.


v.

Remove the 3 bolts and disconnect the wire harness protector labeled A.


vi.

Remove the bolt and wire harness bracket labeled B.


vii.

Remove the nut and glow plug wire harness labeled C.



c.
U163798E02
1.479,1.948 1.604,2.094 0.125,0.146 10 false A

for LHD:

i.

Disconnect the 4 connectors, and detach the wire harness tab from the relay block labeled A.


ii.

Disconnect the ECM connector.


iii.

Disconnect the wire harness from the wire harness clamp holder.



d.

for RHD:

i.
A271635

Disconnect the wire harness from the wire harness clamp holder.


ii.

Remove the bolt and wire harness clamp holder.


iii.
U163799E02
2.219,1.948 2.344,2.094 0.125,0.146 10 false A

Disconnect the 4 connectors, and detach the wire harness tab from the relay block labeled A.


iv.

Disconnect the ECM connector.


v.

Disconnect the wire harness from the wire harness clamp holder.



Hide 23706 48.REMOVE NO. 6 INJECTION PIPE SUB-ASSEMBLY

Hide 25860 49.REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY

Hide 25706 50.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

Hide 11225 51.REMOVE CYLINDER HEAD COVER SILENCER LH

Hide 23765 55.REMOVE NO. 5 NOZZLE LEAKAGE PIPE

Hide 23820A 56.REMOVE COMMON RAIL ASSEMBLY LH

Hide 23801L 57.REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

Hide 11224 59.REMOVE CYLINDER HEAD COVER SILENCER RH

Hide 16630H 61.REMOVE NO. 2 IDLER PULLEY (w/ Viscous Heater)

Hide 62.REMOVE NO. 2 IDLER PULLEY BRACKET (w/ Viscous Heater)

Hide 11227 66.REMOVE CYLINDER HEAD COVER INSULATOR RH

Hide 23711 68.REMOVE NO. 1 FUEL INJECTOR PROTECTOR

Hide 11201 71.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH

Hide 11228A 73.REMOVE CYLINDER HEAD COVER INSULATOR LH

Hide 23712 76.REMOVE NO. 2 FUEL INJECTOR PROTECTOR

Hide 11202 80.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 13511 81.REMOVE NO. 1 AND NO. 2 CAMSHAFTS

a.
A168309E05
1.417,0.375 0.552,0.375 true 0.354,0.281 0.542,0.438 0.188,0.156 10 false *1

Rotate the crankshaft clockwise, and align the No. 1 camshaft timing sprocket arrow with the cylinder head upper surface.

Text in Illustration
*1 Arrow


b.
A168310

Using a 10 mm hexagon wrench, remove the taper screw plug.


c.

Fix the No. 1 chain tensioner in place.

i.

Push the tensioner slipper away from the tensioner, and move the stopper plate clockwise to release the lock as shown in A.


ii.

Push down the tensioner slipper and move the stopper plate counterclockwise to set the lock as shown in B.


iii.

Push the tensioner slipper away from the tensioner, and insert a hexagon wrench into the stopper plate hole as shown in C.

NOTICE:

Do not drop the hexagon wrench into the engine.


U163082E02
0.719,1.646 0.719,2.313 true 0.625,2.333 0.813,2.49 0.188,0.156 10 false *1 2.625,0.313 2.75,0.458 0.125,0.146 10 false A 4.469,0.313 4.594,0.458 0.125,0.146 10 false B 6.385,0.323 6.51,0.469 0.125,0.146 10 false C

Text in Illustration
*1 Stopper Plate - -



d.
A168361E01
0.525,0.993 0.820,1.140 0.295,0.146 10 SST 0.695,0.458 0.695,0.972 false

Using SST, hold the pump drive shaft gear.

SST
09960-10010  (09962-01000, 09963-01000)


e.

Remove the 2 bolts.


f.
A168312E06
1.625,1.323 1.479,1.323 1.479,1.323 1.115,1.01 true 1.635,1.229 1.823,1.385 0.188,0.156 10 false *1

Rotate the crankshaft clockwise 360° so that the No. 1 camshaft timing sprocket arrow points at the No. 1 camshaft center.

Text in Illustration
*1 Arrow

NOTICE:

Do not rotate the crankshaft counterclockwise in order to align the sprocket arrow and camshaft center.



g.
A168313E06
1.49,0.563 2.313,0.281 2.313,0.281 1.573,0.458 true 1.729,1.281 2.292,0.281 2.292,0.281 1.854,1.281 true 2.302,0.281 2.448,0.281 false 2.49,0.188 2.677,0.344 0.188,0.156 10 false *1

Place matchmarks on the No. 1 timing chain and No. 1 camshaft timing sprocket.

Text in Illustration
*1 Matchmark


h.

Place matchmarks on the No. 1 and No. 2 camshaft gears.


i.
A168362E01
1.563,0.122 1.872,0.269 0.309,0.147 10 SST 1.507,0.205 0.626,0.205 false

Using SST, hold the pump drive shaft gear.

SST
09960-10010  (09962-01000, 09963-01000)


j.

Remove the 2 bolts and pump drive shaft gear.


k.

Disconnect the No. 1 timing chain and No. 1 camshaft timing sprocket from the No. 2 camshaft.

NOTICE:
·

Do not remove the No. 1 camshaft timing sprocket from the No. 1 timing chain.

·

Do not rotate the crankshaft until the No. 1 timing chain and No. 1 camshaft timing sprocket are connected to the No. 2 camshaft.



HINT:

If fixing the No. 1 camshaft timing sprocket in place, pass a rope or equivalent through one of the No. 1 camshaft timing sprocket holes and tie the sprocket and chain together.



l.
A168387

Turn the No. 1 camshaft clockwise so that the bolt is easier to install.


m.
A168363

Using a 6 mm x 1.0 pitch service bolt with a length of 16 mm or more, fix the No. 1 camshaft in place.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Do not drop the bolt into the engine.


HINT:

If it is difficult to install the bolt, rotate the camshaft so that the bolt is easier to install.



n.
A168341

Loosen the 2 union bolts.


o.
U162957E02
0.344,0.313 0.5,0.479 0.156,0.167 10 false 1 1.344,0.906 1.521,1.083 0.177,0.177 10 false 10 0.354,0.719 0.51,0.885 0.156,0.167 10 false 2 0.958,1.917 1.135,2.083 0.177,0.167 10 false 11 0.479,1.927 0.635,2.094 0.156,0.167 10 false 3 1.333,1.26 1.51,1.427 0.177,0.167 10 false 12 0.354,1.427 0.51,1.594 0.156,0.167 10 false 4 2.125,0.208 2.302,0.375 0.177,0.167 10 false 13 3.177,0.646 3.333,0.813 0.156,0.167 10 false 5 2.531,0.896 2.708,1.073 0.177,0.177 10 false 14 3.177,0.906 3.333,1.083 0.156,0.177 10 false 6 2.115,1.917 2.292,2.083 0.177,0.167 10 false 15 3.177,1.479 3.333,1.646 0.156,0.167 10 false 7 2.521,1.26 2.698,1.427 0.177,0.167 10 false 16 3.177,1.24 3.333,1.406 0.156,0.167 10 false 8 1.51,0.208 1.688,0.375 0.177,0.167 10 false 17 0.969,0.208 1.125,0.375 0.156,0.167 10 false 9 1.927,0.896 2.104,1.063 0.177,0.167 10 false 18 1.542,1.917 1.719,2.083 0.177,0.167 10 false 19 1.938,1.25 2.115,1.417 0.177,0.167 10 false 20

Uniformly loosen and remove the 20 bolts in the sequence shown in the illustration.


p.
A168343

Remove the 2 union bolts and No. 1 and No. 2 oil feed pipes.


q.
A168344

Remove the 8 No. 3 camshaft bearing caps and No. 1 camshaft bearing cap.

HINT:

Be sure to arrange the removed parts for each installation position separately.



r.
A168345

Remove the No. 1 and No. 2 camshafts.


Hide 13053 82.REMOVE NO. 3 AND NO. 4 CAMSHAFTS

a.
A168319E04
2.208,0.479 3.052,0.479 true 3.073,0.385 3.26,0.542 0.188,0.156 10 false *1

Rotate the crankshaft clockwise, and align the No. 2 camshaft timing sprocket arrow with the cylinder head upper surface.

Text in Illustration
*1 Arrow


b.
A168320

Using a 10 mm hexagon wrench, remove the taper screw plug.


c.

Fix the No. 2 chain tensioner in place.

i.

Push the tensioner slipper away from the tensioner, and move the stopper plate clockwise to release the lock as shown in A.


ii.

Push up the tensioner slipper and move the stopper plate counterclockwise to set the lock as shown in B.


iii.

Push the tensioner slipper away from the tensioner, and insert a hexagon wrench into the stopper plate hole as shown in C.

NOTICE:

Do not drop the hexagon wrench into the engine.


U163084E02
0.844,1.552 0.844,2.354 true 2.677,0.271 2.802,0.417 0.125,0.146 10 false A 4.625,0.271 4.75,0.417 0.125,0.146 10 false B 6.25,0.271 6.375,0.417 0.125,0.146 10 false C 0.75,2.375 0.938,2.531 0.188,0.156 10 false *1

Text in Illustration
*1 Stopper Plate - -



d.
A168364E03
2.712,0.759 3.012,0.918 0.299,0.158 10 SST 2.378,0.174 2.88,0.547 2.88,0.547 2.88,0.717 false

Using SST, hold the No. 2 camshaft timing sprocket.

SST
09960-10010  (09962-01000, 09963-01000)


e.

Remove the 2 bolts.


f.
A168322E05
2.385,0.896 1.698,1.135 1.698,1.135 1.698,1.26 true 1.583,1.281 1.771,1.438 0.188,0.156 10 false *1

Rotate the crankshaft clockwise 360° so that the No. 2 camshaft timing sprocket arrow points at the No. 4 camshaft center.

Text in Illustration
*1 Arrow


g.
A168323E05
1.573,1.333 1.021,0.135 1.021,0.135 1.729,1.333 true 1.969,0.438 1.01,0.146 1.01,0.146 2.063,0.563 true 1,0.146 0.906,0.146 false 0.729,0.063 0.917,0.219 0.188,0.156 10 false *1

Place matchmarks on the No. 2 timing chain and No. 2 camshaft timing sprocket.

Text in Illustration
*1 Matchmark


h.

Place matchmarks on the No. 3 and No. 4 camshaft gears.


i.
A168364E03
2.712,0.759 3.012,0.918 0.299,0.158 10 SST 2.378,0.174 2.88,0.547 2.88,0.547 2.88,0.717 false

Using SST, hold the No. 2 camshaft timing sprocket.

SST
09960-10010  (09962-01000, 09963-01000)


j.

Remove the 2 bolts, and disconnect the No. 2 timing chain and No. 2 camshaft timing sprocket from the No. 3 camshaft.

NOTICE:
·

Do not remove the No. 2 camshaft timing sprocket from the No. 2 timing chain.

·

Do not rotate the crankshaft until the No. 2 timing chain and No. 2 camshaft timing sprocket are connected to the No. 3 camshaft.



HINT:

If fixing the No. 2 camshaft timing sprocket in place, pass a rope or equivalent through one of the No. 2 camshaft timing sprocket holes and tie the sprocket and chain together.



k.
A168365

Using a 6 mm x 1.0 pitch service bolt with a length of 16 mm or more, fix the No. 4 camshaft in place.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Do not drop the bolt into the chain cover.


HINT:

If it is difficult to install the bolt, rotate the camshaft so that the bolt is easier to install.



l.
A168346

Loosen the 2 union bolts.


m.
U162958E02
0.25,0.271 0.406,0.438 0.156,0.167 10 false 1 1.458,0.854 1.635,1.031 0.177,0.177 10 false 10 0.25,0.74 0.406,0.906 0.156,0.167 10 false 2 1.073,1.854 1.25,2.021 0.177,0.167 10 false 11 0.375,1.865 0.531,2.031 0.156,0.167 10 false 3 1.458,1.208 1.635,1.375 0.177,0.167 10 false 12 0.25,1.375 0.406,1.542 0.156,0.167 10 false 4 2.26,0.208 2.438,0.375 0.177,0.167 10 false 13 3.25,0.635 3.406,0.802 0.156,0.167 10 false 5 2.615,0.833 2.792,1 0.177,0.167 10 false 14 3.25,0.896 3.406,1.063 0.156,0.167 10 false 6 2.24,1.854 2.417,2.021 0.177,0.167 10 false 15 3.26,1.427 3.417,1.594 0.156,0.167 10 false 7 2.615,1.198 2.792,1.365 0.177,0.167 10 false 16 3.25,1.198 3.406,1.365 0.156,0.167 10 false 8 1.635,0.208 1.813,0.375 0.177,0.167 10 false 17 1.094,0.208 1.25,0.375 0.156,0.167 10 false 9 2.042,0.854 2.219,1.021 0.177,0.167 10 false 18 1.656,1.854 1.833,2.021 0.177,0.167 10 false 19 2.042,1.208 2.219,1.375 0.177,0.167 10 false 20

Uniformly loosen and remove the 20 bolts in the sequence shown in the illustration.


n.
A168348

Remove the 2 union bolts and No. 3 and No. 4 oil feed pipes.


o.
A168378

Remove the 8 No. 3 camshaft bearing caps and No. 4 camshaft bearing cap.

HINT:

Be sure to arrange the removed parts for each installation position separately.



p.
A168350

Remove the No. 3 and No. 4 camshafts.