Home › Engine / Hybrid System › 3UR-FE (ENGINE MECHANICAL) › CAMSHAFT › from 2017.08
RM2660E _51 Engine / Hybrid System _052777 3UR-FE ENGINE MECHANICAL _0255045 CAMSHAFT A

3UR-FE ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


PROCEDURE

Hide 1.INSTALL CAMSHAFT BEARING CAP RH

a.

Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps.


b.
A316364E03
0.813,0.229 1.115,0.229 1.115,0.229 1.271,1.406 true 1.115,0.229 0.906,0.844 true 0.635,0.146 0.865,0.323 0.229,0.177 10 false *a

Install the No. 1 and No. 2 camshafts to the camshaft housing.

Text in Illustration
*a Identification Mark

HINT:

Check the identification mark stamped on the camshaft.

Item Mark
for Intake Side NO. 1
for Exhaust Side NO. 2



c.

Confirm the marks and numbers on the camshaft bearing caps and place them in their proper positions and directions.


d.
A160687E09
2.792,1.708 2.906,1.875 0.115,0.167 10 true 1 2.823,0.208 2.938,0.375 0.115,0.167 10 true 2 2.104,1.719 2.219,1.885 0.115,0.167 10 true 3 2.104,0.24 2.219,0.406 0.115,0.167 10 false 4 1.552,1.719 1.667,1.885 0.115,0.167 10 true 5 1.552,0.208 1.667,0.375 0.115,0.167 10 false 6 1.01,1.719 1.125,1.885 0.115,0.167 10 true 7 1,0.219 1.115,0.385 0.115,0.167 10 false 8 0.354,1.719 0.469,1.885 0.115,0.167 10 true 9 0.313,0.229 0.5,0.396 0.188,0.167 10 false 10

Temporarily install the 10 bolts in the order shown in the illustration.


Hide 11103C 2.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH

a.
A386786E02
0.896,0.604 1.385,0.604 false 2.375,0.604 2.917,0.604 2.917,0.604 2.917,0.792 false 2.052,0.219 2.563,0.219 false 2.594,0.125 2.823,0.333 0.229,0.208 10 false *1 0.677,0.51 0.906,0.719 0.229,0.208 10 false *3 2.854,0.823 3.083,1.031 0.229,0.208 10 false *2

Make sure that the valve rocker arms are installed as shown in the illustration.

Text in Illustration
*1 Valve Rocker Arm
*2 Valve Stem Cap
*3 Valve Lash Adjuster


b.
A381396E02
1.458,1.76 1.458,1.469 true 1.375,1.781 1.646,1.969 0.271,0.188 10 false *a

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.5 to 4.0 mm (0.138 to 0.157 in.)


Text in Illustration
*a 3.5 to 4.0 mm

NOTICE:
·

Remove any oil from the contact surface.

·

Install the camshaft housing within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




c.
A163556E10
0.865,2.667 1.698,2.979 1.698,2.979 2.25,2.771 false 2.708,1.958 2.802,1.958 2.802,1.958 2.865,1.792 false 1.479,1.271 1.635,1.469 0.156,0.198 10 true 1 0.854,1.281 1.01,1.469 0.156,0.188 10 true 2 1.979,1.281 2.135,1.438 0.156,0.156 10 true 3 0.219,1.281 0.354,1.448 0.135,0.167 10 true 4 2.625,1.271 2.781,1.438 0.156,0.167 10 true 5 1.427,1.854 1.521,2.01 0.094,0.156 10 true 6 1.365,0 1.458,0.156 0.094,0.156 10 false 7 0.875,1.854 0.969,2.01 0.094,0.156 10 true 8 0.844,0 0.938,0.156 0.094,0.156 10 false 9 1.948,1.844 2.135,2 0.188,0.156 10 true 10 1.917,0 2.104,0.156 0.188,0.156 10 false 11 0.177,1.865 0.365,2.021 0.188,0.156 10 true 12 0.188,0 0.375,0.156 0.188,0.156 10 false 13 3.042,1.302 3.229,1.458 0.188,0.156 10 false 14 2.49,0.052 2.677,0.208 0.188,0.156 10 false 15 3.115,0 3.302,0.156 0.188,0.156 10 false 17 2.333,1.677 2.521,1.833 0.188,0.156 10 true 18 0.021,0.396 0.208,0.552 0.188,0.156 10 true 16 1.604,3.01 1.792,3.188 0.188,0.177 10 false *3 0.573,2.188 0.948,2.385 0.375,0.198 10 false 55° 2,2.271 2.375,2.469 0.375,0.198 10 false 70° 1.229,2.198 1.427,2.375 0.198,0.177 10 false *1 2.625,2.177 2.833,2.354 0.208,0.177 10 false *2 2.573,1.875 2.698,2.042 0.125,0.167 10 false A

Install the camshaft housing, and install the 18 bolts in the order shown in the illustration.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
except bolt A : 30 N*m (306 kgf*cm, 22 ft.*lbf)

Text in Illustration
*1 EX
*2 IN
*3 Knock Pin

NOTICE:
·

Do not start the engine for at least 2 hours after the installation.

·

Make sure that the knock pin of the camshaft is positioned as shown in the illustration before installing the camshaft housing.




d.
A160684E17
2.823,1.646 2.938,1.802 0.115,0.156 10 true 1 2.802,0.198 2.917,0.354 0.115,0.156 10 true 2 2.125,1.646 2.24,1.802 0.115,0.156 10 true 3 2.104,0.219 2.219,0.375 0.115,0.156 10 false 4 1.563,1.646 1.677,1.802 0.115,0.156 10 true 5 1.552,0.208 1.667,0.365 0.115,0.156 10 false 6 0.99,1.646 1.104,1.802 0.115,0.156 10 true 7 0.969,0.188 1.083,0.344 0.115,0.156 10 false 8 0.365,1.646 0.479,1.802 0.115,0.156 10 true 9 0.313,0.198 0.5,0.354 0.188,0.156 10 false 10

Tighten the 10 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)

NOTICE:

Thoroughly wipe clean any seal packing.



Hide 3.INSTALL CAMSHAFT BEARING CAP LH

a.

Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps.


b.
A316369E03
0.917,1.563 1.146,1.375 true 0.927,1.844 0.927,1.323 0.927,1.323 1.49,0.854 true 0.854,1.875 1.177,2.073 0.323,0.198 10 false *a

Install the No. 3 and No. 4 camshafts to the camshaft housing.

Text in Illustration
*a Identification Mark

HINT:

Check the identification mark stamped on the camshaft.

Item Mark
for Intake Side NO. 3
for Exhaust Side NO. 4



c.

Confirm the marks and numbers on the camshaft bearing caps and place them in their proper positions and directions.


d.
U155670E04
2.74,0.292 2.844,0.438 0.104,0.146 10 true 1 2.76,1.792 2.906,1.958 0.146,0.167 10 true 2 2.135,0.271 2.24,0.417 0.104,0.146 10 true 3 2.135,1.792 2.24,1.938 0.104,0.146 10 false 4 1.656,0.26 1.76,0.406 0.104,0.146 10 false 5 1.667,1.802 1.771,1.948 0.104,0.146 10 false 6 1.167,0.271 1.365,0.417 0.198,0.146 10 true 7 1.167,1.781 1.271,1.927 0.104,0.146 10 false 8 0.625,0.271 0.74,0.417 0.115,0.146 10 false 9 0.552,1.781 0.74,1.938 0.188,0.156 10 false 10

Temporarily install the 10 bolts in the order shown in the illustration.


Hide 11104A 4.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH

a.
A386786E02
0.896,0.604 1.385,0.604 false 2.375,0.604 2.917,0.604 2.917,0.604 2.917,0.792 false 2.052,0.219 2.563,0.219 false 2.594,0.125 2.823,0.333 0.229,0.208 10 false *1 0.677,0.51 0.906,0.719 0.229,0.208 10 false *3 2.854,0.823 3.083,1.031 0.229,0.208 10 false *2

Make sure that the valve rocker arms are installed as shown in the illustration.

Text in Illustration
*1 Valve Rocker Arm
*2 Valve Stem Cap
*3 Valve Lash Adjuster


b.
A178523E05
1.365,1.76 1.365,1.271 false 1.302,1.792 1.49,2.01 0.188,0.219 10 false *a

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.5 to 4.0 mm (0.138 to 0.157 in.)


Text in Illustration
*a 3.5 to 4.0 mm

NOTICE:
·

Remove any oil from the contact surface.

·

Install the camshaft housing within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




c.
A163732E10
0.927,2.604 1.823,2.948 1.823,2.948 2.521,2.583 false 2.771,0.073 2.865,0.073 2.865,0.073 2.938,0.229 false 1.51,0.531 1.656,0.688 0.146,0.156 10 true 1 1.042,0.531 1.188,0.688 0.146,0.156 10 true 2 2.156,0.531 2.292,0.688 0.135,0.156 10 true 3 0.406,0.542 0.552,0.698 0.146,0.156 10 true 4 2.813,0.531 2.969,0.708 0.156,0.177 10 true 5 1.604,0 1.708,0.156 0.104,0.156 10 false 6 1.521,1.865 1.625,2.021 0.104,0.156 10 true 7 1.042,0 1.146,0.156 0.104,0.156 10 false 8 1.031,1.854 1.135,2.01 0.104,0.156 10 true 9 2.135,0 2.323,0.156 0.188,0.156 10 false 10 2.083,1.854 2.271,2.01 0.188,0.156 10 true 11 0.354,0 0.542,0.156 0.188,0.156 10 false 12 0.365,1.854 0.552,2.01 0.188,0.156 10 true 13 3.208,0.542 3.396,0.698 0.188,0.156 10 false 14 2.646,1.792 2.833,1.948 0.188,0.156 10 true 15 0.052,1.438 0.24,1.594 0.188,0.156 10 false 16 2.979,1.396 3.167,1.552 0.188,0.156 10 false 17 1.302,2.156 1.49,2.333 0.188,0.177 10 false *1 2.875,2.146 3.083,2.333 0.208,0.188 10 false *2 1.708,2.969 1.885,3.146 0.177,0.177 10 false *3 2.5,2.083 2.781,2.26 0.281,0.177 10 false 3° 0.698,2.156 1.01,2.365 0.313,0.208 10 false 45° 3.208,0.052 3.396,0.208 0.188,0.156 10 false 18 2.625,0 2.76,0.167 0.135,0.167 10 false A

Install the camshaft housing, and install the 18 bolts in the order shown in the illustration.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
except bolt A : 30 N*m (306 kgf*cm, 22 ft.*lbf)

Text in Illustration
*1 IN
*2 EX
*3 Knock Pin

NOTICE:
·

Do not start the engine for at least 2 hours after the installation.

·

Make sure that the knock pin of the camshaft is positioned as shown in the illustration before installing the camshaft housing.




d.
A163592E19
2.875,1.729 2.99,1.917 0.115,0.188 10 true 2 2.188,0.198 2.344,0.406 0.156,0.208 10 true 3 2.156,1.729 2.271,1.917 0.115,0.188 10 false 4 1.635,0.198 1.781,0.385 0.146,0.188 10 true 5 1.604,1.729 1.719,1.917 0.115,0.188 10 false 6 1.073,0.208 1.198,0.396 0.125,0.188 10 true 7 1.021,1.729 1.135,1.917 0.115,0.188 10 false 8 0.385,1.729 0.563,1.917 0.177,0.188 10 false 10 0.448,0.219 0.604,0.385 0.156,0.167 10 true 9 2.885,0.219 3.031,0.417 0.146,0.198 10 true 1

Tighten the 10 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)

NOTICE:

Thoroughly wipe clean any seal packing.



Hide 13550 7.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

Hide 13561 9.INSTALL NO. 1 CHAIN VIBRATION DAMPER RH

Hide 13559 10.INSTALL NO. 1 CHAIN TENSIONER SLIPPER RH

Hide 13540 11.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY RH

Hide 13560A 12.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY

Hide 13559 14.INSTALL NO. 1 CHAIN TENSIONER SLIPPER LH

Hide 13540 15.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY LH

Hide 13561 16.INSTALL NO. 1 CHAIN VIBRATION DAMPER LH

Hide 13050 17.TIGHTEN CAMSHAFT TIMING GEAR ASSEMBLY

Hide 11302 20.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 11202 22.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 11201 23.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH

Hide 16603 28.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 17303 31.INSTALL AIR PIPE SUB-ASSEMBLY (w/ Secondary Air Injection System)

Hide 12611 32.INSTALL NO. 1 ENGINE COVER

Hide 11212 33.INSTALL NO. 2 ENGINE COVER

Hide 16355 34.INSTALL FRONT WATER BY-PASS JOINT

Hide 16206 35.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16261G 36.INSTALL NO. 1 WATER BY-PASS HOSE

Hide 16207 43.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 83520 44.INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY

Hide 23902 47.CONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY

Hide 88320 48.CONNECT COOLER COMPRESSOR ASSEMBLY

Hide 49.CONNECT WATER PIPE AND HOSE SUB-ASSEMBLY

Hide 50.CONNECT AIR PUMP HOSE AND WIRE HARNESS (w/ Secondary Air Injection System)

Hide 16572D 54.INSTALL NO. 2 RADIATOR HOSE

Hide 16571C 55.INSTALL NO. 1 RADIATOR HOSE

Hide 61.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53736G 67.INSTALL FRONT FENDER APRON SEAL FRONT RH

Hide 51405C 70.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 55781E 71.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53883F 73.INSTALL FRONT FENDER MAIN SEAL LH

Hide 53882H 74.INSTALL FRONT FENDER MAIN SEAL RH

Hide 53294C 77.INSTALL RADIATOR SIDE DEFLECTOR LH

Hide 32917 78.INSTALL TRANSMISSION OIL COOLER AIR DUCT