Home › Drivetrain › H152F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION ASSEMBLY › from 2022.09
RM25T0E _52 Drivetrain _058021 H152F MANUAL TRANSMISSION / TRANSAXLE _0282327 MANUAL TRANSMISSION ASSEMBLY A

H152F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 31236B 1.INSTALL RELEASE FORK SUPPORT

Hide 31237 2.INSTALL CLUTCH RELEASE FORK SUPPORT BOOT

Hide 31204 3.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

Hide 4.INSTALL EXHAUST PIPE SUPPORT

a.
C363500

Install the exhaust pipe support with the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 5.INSTALL WIRE HARNESS CLAMP BRACKET

a.
C363661

Install the 4 wire harness clamp brackets with the 4 bolts.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


Hide 8.INSTALL MANUAL TRANSMISSION WITH TRANSFER

C160844

a.

Install the manual transmission with transfer with the 10 bolts.

Torque:
71.6 N*m (730 kgf*cm, 53 ft.*lbf)


Hide 9.CONNECT WIRE HARNESS

a.

Connect the 16 wire harness clamps and 3 wire harness connectors to the manual transmission with transfer.

C361275


b.

Tilt up the manual transmission with transfer.


Hide 10.CONNECT GROUND CABLE

a.
C361274

Connect the ground cable with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 12371 11.INSTALL REAR ENGINE MOUNTING INSULATOR

C161536

a.

Install the rear engine mounting insulator to the manual transmission with transfer with the 4 bolts.

Torque:
59 N*m (602 kgf*cm, 44 ft.*lbf)


Hide 51203 12.INSTALL NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY

C160838

a.

except Single Cab:

i.

Install the No. 2 frame crossmember sub-assembly with the 2 nuts.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)


ii.

Install the 8 bolts.

Torque:
46 N*m (469 kgf*cm, 34 ft.*lbf)



b.
C361273

for Single Cab:

i.

Install the No. 2 frame crossmember sub-assembly with the 2 nuts.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)


ii.

Install the 4 bolts and 4 nuts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)



Hide 12140 13.INSTALL OIL PAN COVER

C163585

a.

Install the oil pan cover with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 14.INSTALL FRONT STABILIZER BRACKET LH

C161532

a.

Install the front stabilizer bracket LH with the 2 bolts.

Torque:
29.7 N*m (303 kgf*cm, 22 ft.*lbf)


Hide 15.INSTALL FRONT STABILIZER BRACKET RH

HINT:

Use the same procedure described for the LH side.


Hide 31470 16.INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY

C160837

a.

Install the clutch release cylinder assembly with the 2 bolts.

Torque:
11.8 N*m (120 kgf*cm, 9 ft.*lbf)


Hide 37110 17.INSTALL REAR PROPELLER SHAFT ASSEMBLY

Hide 37140 18.INSTALL FRONT PROPELLER SHAFT ASSEMBLY

Hide 51447C 19.INSTALL TRANSFER CASE PROTECTOR

C161524

a.

Install the transfer case protector to the No. 2 frame crossmember sub-assembly with the 3 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 36308 21.CONNECT HIGH AND LOW SHIFT ROD SUB-ASSEMBLY

a.

Connect the high and low shift rod sub-assembly with the washer and nut.

Torque:
11.76 N*m (120 kgf*cm, 9 ft.*lbf)


Hide 23.INSPECT AND ADJUST TRANSFER SHIFT LEVER ASSEMBLY

Hide 33530F 24.INSTALL TRANSMISSION SHIFT LEVER ASSEMBLY

C353575C01
1.948,1.365 2.292,1.656 2.292,1.656 2.51,1.656 false 2.604,1.563 2.948,1.781 0.344,0.219 11 false *1
*1 Shift Lever Cap
V113147

Press Down
V113148

Clockwise
V113149

Lock


a.

Cover the transmission shift lever cap with a cloth or equivalent.


b.

While pressing down on the transmission shift lever cap, turn it clockwise to install the transmission shift lever.


c.

Attach the shift lever cap boot.


Hide 58286 25.INSTALL NO. 1 SHIFT AND SELECT LEVER BOOT

Hide 36303 26.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

Hide 89170 28.INSTALL AIRBAG SENSOR ASSEMBLY WITH AIRBAG SENSOR BRACKET

Hide 58191 31.INSTALL FRONT FLOOR FOOTREST (except Pickup)

Hide 62111A 33.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 67913 35.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 87240H 36.INSTALL HEATER WATER VALVE ASSEMBLY

C162223

a.

Install the heater water valve assembly to the vehicle with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Connect the 2 hoses to the heater water valve assembly and slide the 2 clamps to secure the hoses.


c.
C162224

Connect the cable to the heater water valve assembly.


Hide 16470 39.INSTALL RADIATOR RESERVOIR ASSEMBLY

Hide 17875 40.INSTALL INTAKE AIR CONNECTOR PIPE

Hide 17805 41.INSTALL INTAKE AIR CONNECTOR SUB-ASSEMBLY

Hide 42.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17881 44.INSTALL NO. 1 AIR CLEANER HOSE

Hide 16571C 45.INSTALL NO. 1 RADIATOR HOSE

Hide 48.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 51442 53.INSTALL NO. 2 ENGINE UNDER COVER

Hide 54. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART