The engine assembly with transmission is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.
1. PRECAUTION
The vehicle has a hybrid system that operates at voltages up to 650 V. The hybrid system uses an HV battery that contains an electrolyte which is a strong alkali solution that includes potassium hydroxide. Be sure to follow the instructions in this manual to handle the system correctly. Failure to do so may result in serious injury or electrocution (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
3. DISCHARGE FUEL SYSTEM PRESSURE
G3834
4.REMOVE SERVICE PLUG GRIP
5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
51442C
6.REMOVE ENGINE UNDER COVER LH
51441C
7.REMOVE ENGINE UNDER COVER RH
8.DRAIN ENGINE OIL
9.DRAIN COOLANT (for Engine)
10.DRAIN COOLANT (for Inverter)
11.DRAIN HYBRID TRANSAXLE FLUID
12.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
55722C
13.REMOVE INNER COWL TOP TO COWL BRACE (for LHD)
55722C
14.REMOVE INNER COWL TOP TO COWL BRACE (for RHD)
55735B
15.REMOVE FRONT AIR SHUTTER SEAL (for LHD)
55735B
16.REMOVE FRONT AIR SHUTTER SEAL (for RHD)
55815E
17.REMOVE FRONT NO. 1 VENTILATOR SEAL (for LHD)
55815E
18.REMOVE FRONT NO. 1 VENTILATOR SEAL (for RHD)
55701J
19.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)
55701J
20.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
G9200
21.REMOVE INVERTER WITH CONVERTER ASSEMBLY
17705
22.REMOVE AIR CLEANER CAP SUB-ASSEMBLY
23.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
G9110
24.REMOVE INVERTER BRACKET ASSEMBLY
Wear insulated gloves.
Remove the bolt and separate the motor cable protector.
Disconnect the 2 wire harness clamps.
Remove the 2 bolts and separate the inverter reservoir tank assembly.
Remove the bolt and disconnect the earth wire.
Remove the 4 bolts and inverter bracket assembly.
16571C
25.DISCONNECT NO. 1 RADIATOR HOSE
Disconnect the No. 1 radiator hose from the engine assembly.
16572D
26.DISCONNECT NO. 2 RADIATOR HOSE
Disconnect the No. 2 radiator hose from the engine assembly.
27.DISCONNECT HEATER WATER HOSE
Disconnect the 2 heater water hoses from the engine assembly.
23820
28.DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY
Disconnect the fuel vapor feed hose assembly.
23901
29.DISCONNECT FUEL TUBE SUB-ASSEMBLY
82121
30.DISCONNECT ENGINE WIRE (for LHD)
Push the lock on the lever, then raise the lever, and disconnect the ECM connector.
If there is any foreign matter such as mud or water on a connector, clean the connector.
Disconnect the 2 wire harness clamps.
Disconnect the 2 connectors and wire harness clamp.
Using a screwdriver, disengage the claw and disconnect the engine wire from the engine room relay block and junction block assembly.
Disconnect the engine wire from the engine room main wire.
Disconnect the wire harness clamp.
82121
31.DISCONNECT ENGINE WIRE (for RHD)
Push the lock on the lever, then raise the lever, and disconnect the ECM connector.
If there is any foreign matter such as mud or water on a connector, clean the connector.
Disconnect the 2 connectors and wire harness clamp.
Using a screwdriver, disengage the claw and disconnect the engine wire from the engine room relay block and junction block assembly.
Disconnect the engine wire from the engine room main wire.
Disconnect the wire harness clamp.
33820B
32.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
33.PLACE FRONT WHEELS FACING STRAIGHT AHEAD
34.SECURE STEERING WHEEL
45259A
35.REMOVE COLUMN HOLE COVER SILENCER SHEET
45209
36.SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY
45025D
37.DISCONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
88711
38.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
88704
39.DISCONNECT SUCTION HOSE SUB-ASSEMBLY
88370
40.REMOVE COMPRESSOR WITH MOTOR ASSEMBLY
17410
41.REMOVE FRONT EXHAUST PIPE ASSEMBLY
42.SEPARATE NO. 2 ENGINE ROOM RELAY BLOCK AND NO. 2 JUNCTION BLOCK ASSEMBLY
43.REMOVE FRONT DRIVE SHAFT ASSEMBLY
11361J
44.REMOVE FLYWHEEL HOUSING UNDER COVER
Remove the flywheel housing under cover.
45.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
Set the engine lifter.
| *1 | No. 2 Oil Pan Sub-assembly |
| *2 | Drain Plug |
| *3 | Rear Cover Plug |
|
Attachment Installation Position |
Place the height adjustment attachment and plate lift attachment so that the engine assembly with transaxle is level.
Securely support the engine assembly to prevent it from turning upside down until it is secured to an engine stand.
To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments onto the No. 2 oil pan sub-assembly of the engine assembly.
Do not place any attachments onto the drain plug and rear cover plug of the hybrid vehicle transaxle assembly.
Remove the bolt and 2 nuts, and separate the engine mounting insulator sub-assembly RH from the engine assembly.
Remove the bolt and nut, and separate the engine mounting insulator LH from the engine mounting bracket LH.
Remove the 6 bolts, operate the engine lifter and slowly remove the engine assembly with transaxle and front suspension crossmember sub-assembly from the vehicle.
Make sure that the engine is clear of all wiring and hoses.
12281A
46.INSTALL NO. 1 ENGINE HANGER
Install the 2 No. 1 engine hangers with 2 new bolts.
| Part Name | Part No. |
|---|---|
| No. 1 engine hanger | 12281-21090 |
| Bolt | 91672-81025 |
47.FIX ENGINE ASSEMBLY WITH TRANSAXLE
Attach the sling device to the engine hangers and chain block.
Make sure that the sling angle is correct to prevent the engine assembly and engine hangers from being damaged or deformed.
To enable removal of the engine assembly, adjust the positions of the height adjustment attachment and plate lift attachment and set them in place.
| *1 | No. 2 Oil Pan Sub-assembly |
| *2 | Drain Plug |
| *3 | Rear Cover Plug |
|
Attachment Installation Position |
Place the height adjustment attachment and plate lift attachment so that the engine assembly with transaxle is level.
Securely support the engine assembly to prevent it from turning upside down until it is secured to an engine stand.
To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments onto the No. 2 oil pan sub-assembly of the engine assembly.
Do not place any attachments onto the drain plug and rear cover plug of the hybrid vehicle transaxle assembly.
Using a rope or belt, secure the engine assembly with transaxle to the engine lifter.
Set the engine assembly with transaxle so that it is horizontal.
Do not tighten the rope or belt with a tightening mechanism or any more than is necessary.
48.REMOVE ENGINE ASSEMBLY
Disconnect the 4 clamps and No. 2 engine wire.
Remove the 3 bolts and disconnect the 4 connectors, 7 clamps and wire harness from the hybrid vehicle transaxle assembly.
Remove the 3 bolts, 2 wire harness clamp brackets and transmission control cable clamp from the hybrid vehicle transaxle assembly.
| *1 | Wire Harness Clamp Bracket |
| *2 | Transmission Control Cable Clamp |
Remove the bolt, nut and drive shaft heat insulator sub-assembly from the engine and drive shaft heat insulator bracket.
Disconnect the clamp from the drive shaft heat insulator bracket.
Remove the 2 bolts and drive shaft heat insulator bracket from the engine.
Remove the 2 bolts and starter hole heat insulator from the engine.
Disengage the claw and remove the flywheel housing side cover from the engine.
Remove the 6 bolts and hybrid vehicle transaxle assembly.
To avoid damage to the knock pins, do not pry between the hybrid vehicle transaxle assembly and the engine.
To prevent the splines of the damper from becoming misaligned, do not allow the transaxle to hit the damper during transaxle removal and installation.
31270
49.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY
Gently place the engine assembly onto wood blocks or equivalent.
Set the engine assembly so that it is horizontal.
To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments onto the No. 2 oil pan sub-assembly of the engine assembly.
This step should be done while hanging the engine assembly using the sling device and chain block.
Remove the transmission input damper assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE MECHANICAL)>REAR CRANKSHAFT OIL SEAL>REMOVAL).
13405
50.REMOVE FLYWHEEL SUB-ASSEMBLY
Gently place the engine assembly onto wood blocks or equivalent.
Set the engine assembly so that it is horizontal.
To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments onto the No. 2 oil pan sub-assembly of the engine assembly.
This step should be done while hanging the engine assembly using the sling device and chain block.
Remove the flywheel sub-assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE MECHANICAL)>REAR CRANKSHAFT OIL SEAL>REMOVAL).
12305
51.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.
Remove the 3 bolts and engine mounting insulator sub-assembly RH.
12372A
52.REMOVE ENGINE MOUNTING INSULATOR LH
Perform this procedure only when replacement of the engine mounting insulator LH is necessary.
Disconnect the wire harness clamp.
Remove the 5 bolts and engine mounting insulator LH.
53.INSTALL ENGINE STAND
Using a sling device and chain block, install the engine stand to the engine assembly.
Make sure that the sling angle is correct to prevent the engine assembly and engine hangers from being damaged or deformed.
Securely support the engine assembly to prevent it from turning upside down until it is secured to an engine stand.
82121
54.DISCONNECT ENGINE WIRE
Disconnect all of the clamps and connectors and remove the engine wire from the engine assembly.
12281A
55.REMOVE NO. 1 ENGINE HANGER
Remove the 2 bolts and 2 No. 1 engine hangers.