Home › Engine / Hybrid System › 2ZR-FXE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2020.08
RM2070E _51 Engine / Hybrid System _061907 2ZR-FXE ENGINE MECHANICAL _0301598 ENGINE ASSEMBLY A

2ZR-FXE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
·

The engine assembly with transmission is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.

·

The vehicle has a hybrid system that operates at voltages up to 650 V. The hybrid system uses an HV battery that contains an electrolyte which is a strong alkali solution that includes potassium hydroxide. Be sure to follow the instructions in this manual to handle the system correctly. Failure to do so may result in serious injury or electrocution (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 4.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 5.REMOVE FRONT WHEEL

Hide 51444A 6.REMOVE REAR ENGINE UNDER COVER LH

Hide 51443C 7.REMOVE REAR ENGINE UNDER COVER RH

Hide 52618A 8.REMOVE FRONT LOWER BUMPER ABSORBER

Hide 51441 9.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51442E 10.REMOVE NO. 2 ENGINE UNDER COVER

Hide 11212 15.REMOVE NO. 2 CYLINDER HEAD COVER

a.
A213020

Remove the 3 clips and No. 2 cylinder head cover.

NOTICE:
·

Attempting to disengage both front and rear clips at the same time may cause the No. 2 cylinder cover to break.

·

Pull the No. 2 cylinder cover straight up to remove it. Attempting to pull the No. 2 cylinder cover forward may cause it to break.




Hide 53289A 16.REMOVE RADIATOR SUPPORT OPENING COVER

Hide 17705 17.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

a.
A213021

Disconnect the air flow meter connector.


b.

Disconnect the 2 clamps and hose band, and remove the air cleaner cap sub-assembly.


c.

Remove the air cleaner filter element.


Hide 17750A 18.REMOVE INLET AIR CLEANER ASSEMBLY

a.
A269507

Remove the 2 bolts and inlet air cleaner assembly.


Hide 19.REMOVE AIR CLEANER CASE

a.
A213023

Separate the 3 clamps and No. 4 water by-pass hose from the air cleaner case.


b.

Remove the 3 bolts and air cleaner case.


Hide G92A0A 33.REMOVE INVERTER RESERVE TANK ASSEMBLY

a.
A213024

Remove the 2 bolts and inverter reserve tank assembly.


Hide G9219A 34.REMOVE INVERTER TRAY BRACKET

a.
A213025

Separate the 2 clamps.


b.

Remove the 5 bolts and inverter tray bracket.


Hide 16571C 35.DISCONNECT NO. 1 RADIATOR HOSE

a.
A213026

Slide the clamp and disconnect the No. 1 radiator hose from the radiator pipe.


Hide 16572D 36.DISCONNECT NO. 2 RADIATOR HOSE

a.
A213027

Slide the clamp and disconnect the No. 2 radiator hose from the water inlet.


Hide 16281 37.DISCONNECT NO. 4 WATER BY-PASS HOSE

a.
A213028

Slide the clamp and disconnect the No. 4 water by-pass hose from the radiator pipe.


Hide G9227A 38.DISCONNECT NO. 3 INVERTER COOLING HOSE

a.
A215988

Slide the clamp and disconnect the No. 3 inverter cooling hose from the hybrid vehicle transaxle assembly.


Hide G9229A 39.DISCONNECT NO. 5 INVERTER COOLING HOSE

a.
A258269

Slide the clamp and disconnect the No. 5 inverter cooling hose from the hybrid vehicle transaxle assembly.


Hide 87246A 40.DISCONNECT OUTLET HEATER WATER HOSE

a.
A213030

Slide the clamp and disconnect the outlet heater water hose.


Hide 87245A 41.DISCONNECT INLET HEATER WATER HOSE

a.
A213031

Slide the clamp and disconnect the inlet heater water hose.


Hide 42.DISCONNECT HEATER HOSE

a.
A218276

Slide the clamp and disconnect the heater hose.


Hide 23826 43.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

a.
A213033

Slide the clamp and disconnect the No. 1 fuel vapor feed hose.


Hide 23901 44.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A275980

Release the claw and remove the No. 1 fuel pipe clamp.


b.
A213035

Pinch the retainer as illustrated, then pull the fuel tube connector out of the pipe.

NOTICE:
·

Remove any dirt and foreign matter from the fuel tube connector before performing this work.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting, as the fuel tube connector has the O-rings that seal the pipe.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, kink or twist the nylon tube.

·

Protect the disconnected parts by covering them with plastic bags after disconnecting the fuel tube.

·

If the fuel tube connector and pipe are stuck, push and pull to release them.




Hide 88370 45.SEPARATE COMPRESSOR WITH MOTOR ASSEMBLY

Hide 82121 46.DISCONNECT ENGINE WIRE

a.
A213036

Disconnect the 2 clamps.


b.

Pull up the lever and disconnect the ECM connector.


c.
A241115

Disconnect the 2 connectors, 2 clamps and engine wire from the engine room junction block.


d.
A213038

Disconnect the 3 clamps.


e.
A213039

Remove the bolt and disconnect the earth wire.


f.
A213040

Disconnect the 2 clamps and engine wire.


Hide 45259A 48.REMOVE COLUMN HOLE COVER SILENCER SHEET (for LHD)

Hide 45260 49.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (for LHD)

Hide 45025D 50.DISCONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 43501H 55.REMOVE FRONT AXLE SHAFT NUT RH

HINT:

Perform the same procedure as for the LH side.


Hide 89543 56.SEPARATE FRONT SPEED SENSOR LH

Hide 89542 57.SEPARATE FRONT SPEED SENSOR RH

HINT:

Perform the same procedure as for the LH side.


Hide 45047 58.SEPARATE TIE ROD END SUB-ASSEMBLY LH

Hide 45046 59.SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48810 60.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 61.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48069 62.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 63.SEPARATE FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 43420 64.SEPARATE FRONT DRIVE SHAFT ASSEMBLY LH

Hide 43410 66.SEPARATE FRONT DRIVE SHAFT ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 43410 67.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 43040B 68.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH

Hide 43030B 69.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING RH

HINT:

Perform the same procedure as for the LH side.


Hide 51425A 70.REMOVE FRONT LOWER ENGINE MOUNTING BRACKET REINFORCEMENT

Hide 51108A 71.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

Hide 51107A 72.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

Hide 52258A 73.REMOVE FRONT SUSPENSION MEMBER REAR BRACE LH

Hide 52257 74.REMOVE FRONT SUSPENSION MEMBER REAR BRACE RH

HINT:

Perform the same procedure as for the LH side.


Hide 51201 75.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 76.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.
A216482

Set an engine lifter.

NOTICE:

Place the engine assembly on wooden blocks or equivalent so that the engine assembly is level.



b.
A213042

Remove the 4 bolts and separate the front crossmember sub-assembly.


c.
A150570

Remove the bolt and 2 nuts, and separate the engine mounting insulator sub-assembly RH.


d.
A213043

Remove the bolt and nut, and separate the engine mounting insulator LH.


e.

Carefully remove the engine assembly with transaxle from the vehicle.


f.
A214905E01
2.262,1.087 2.418,1.087 false 2.444,1.012 2.612,1.163 0.168,0.151 10 *1 2.073,3.336 2.196,3.336 false 2.22,3.261 2.388,3.412 0.168,0.151 10 *2

Install the No. 1 engine hanger and No. 2 engine hanger with the 2 bolts.

Text in Illustration
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

Part Name Part No.
No. 1 engine hanger 12281-37021
12281-37070
12281-0T040
No. 2 engine hanger 12282-37011
12282-37060
12282-0T040
Bolt 91552-81050
90105-W0204


g.

Attach an engine sling device and hang the engine assembly with a chain block.


Hide 57104E 77.REMOVE FRONT CROSSMEMBER SUB-ASSEMBLY

a.
A213041

Remove the bolt and nut, and separate the front engine mounting insulator from the front engine mounting bracket.


Hide 12361A 78.REMOVE FRONT ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.


a.
A217722

Remove the 2 bolts and front engine mounting insulator.


Hide 12371A 79.REMOVE REAR ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


a.
A213044

Remove the through bolt and rear engine mounting insulator.


Hide 12372A 80.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A215740

Remove the 4 bolts and engine mounting insulator LH.


Hide 12305 81.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A281978

Remove the 2 bolts and 2 cooler brackets.


b.

Disconnect the earth wire clamp from the engine mounting insulator sub-assembly RH.


c.

Remove the 3 bolts and engine mounting insulator sub-assembly RH.


Hide 16577C 82.REMOVE RADIATOR PIPE

a.
A213045

Slide the clamp and remove the No. 3 radiator hose from the cylinder head.


b.

Remove the 2 bolts and radiator pipe.


Hide 82121 85.REMOVE ENGINE WIRE

a.

Disconnect all the wire harnesses and connectors. Make sure that no wire harnesses are connected to the engine assembly.


Hide 30900 86.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY

a.

Remove the hybrid vehicle transaxle assembly (See page Drivetrain>P410 (HYBRID TRANSMISSION / TRANSAXLE)>HYBRID VEHICLE TRANSAXLE>REMOVAL).

NOTICE:

Be careful not to apply excessive force to the transmission input damper assembly when removing or installing the hybrid vehicle transaxle assembly. If excessive force is applied, the transmission input damper assembly may be damaged, or its splines may become misaligned.



Hide 31270 87.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY

a.

Gently place the engine assembly onto wood blocks or equivalent.

NOTICE:

This step should be done while hanging the engine assembly using the engine hangers and a chain block.



b.

Remove the transmission input damper assembly (See page Engine / Hybrid System>2ZR-FXE (ENGINE MECHANICAL)>REAR CRANKSHAFT OIL SEAL>REMOVAL).


Hide 13405 88.REMOVE FLYWHEEL SUB-ASSEMBLY