1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
G3834
2.REMOVE SERVICE PLUG GRIP
53301
3.REMOVE HOOD SUB-ASSEMBLY
Disconnect the clamp and washer hose.
Remove the 4 bolts and hood sub-assembly from the hood hinge assembly RH and hood hinge assembly LH.
4.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
5.REMOVE FRONT WHEELS
51444A
6.REMOVE REAR ENGINE UNDER COVER LH
51443C
7.REMOVE REAR ENGINE UNDER COVER RH
52618A
8.REMOVE FRONT LOWER BUMPER ABSORBER
51441
9.REMOVE NO. 1 ENGINE UNDER COVER
51442E
10.REMOVE NO. 2 ENGINE UNDER COVER
11.DRAIN COOLANT (for Engine)
12.DRAIN COOLANT (for Inverter)
13.DRAIN HYBRID TRANSAXLE FLUID
14.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
55736D
15.REMOVE COWL BODY MOUNTING REINFORCEMENT LH (for LHD)
55735C
16.REMOVE COWL BODY MOUNTING REINFORCEMENT RH (for RHD)
55701J
17.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)
55701J
18.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
11212
19.REMOVE NO. 2 CYLINDER HEAD COVER
17705
20.REMOVE AIR CLEANER CAP SUB-ASSEMBLY
17750A
21.REMOVE INLET AIR CLEANER ASSEMBLY
22.REMOVE AIR CLEANER CASE
23.REMOVE AIR CLEANER HOSE ASSEMBLY
53289A
24.REMOVE RADIATOR SUPPORT OPENING COVER
G9214
25.REMOVE NO. 1 INVERTER BRACKET
82111
26.DISCONNECT ENGINE ROOM MAIN WIRE
G9221
27.REMOVE INVERTER COVER
28.CHECK TERMINAL VOLTAGE
82164
29.DISCONNECT FRAME WIRE
G2148
30.DISCONNECT GENERATOR CABLE
G1148
31.DISCONNECT MOTOR CABLE
82122
32.DISCONNECT NO. 2 ENGINE WIRE
G9221
33.INSTALL INVERTER COVER
82112
34.DISCONNECT NO. 2 ENGINE ROOM WIRE
35.DISCONNECT WATER HOSE
G9200
36.REMOVE INVERTER WITH CONVERTER ASSEMBLY
G92A0A
37.REMOVE INVERTER RESERVE TANK ASSEMBLY
G9219A
38.REMOVE INVERTER TRAY BRACKET
16571C
39.DISCONNECT NO. 1 RADIATOR HOSE
16281
40.DISCONNECT NO. 4 WATER BY-PASS HOSE
16577C
41.REMOVE RADIATOR PIPE
G9227A
42.DISCONNECT NO. 3 INVERTER COOLING HOSE
G9229A
43.DISCONNECT NO. 5 INVERTER COOLING HOSE
G9228B
44.REMOVE WATER HOSE
Disconnect the clamp from the wire harness clamp bracket.
Disconnect the 2 hose clamps and remove the water hose.
45.DISCONNECT WIRE HARNESS
Disconnect the 2 clamps.
Pull up the lever and disconnect the connector of the ECM.
Disconnect the 2 connectors and clamp from the engine room junction block and separate the wire harness.
Disconnect the 2 clamps.
Remove the bolt and disconnect the earth wire.
Release the green-colored lock and disconnect the connector as shown in the illustration.
Wear insulated gloves when performing the procedure.
Insulate the connector by sealing it with tape.
| *a | Green-colored Lock |
Disconnect the clamp and wire harness.
Remove the 2 bolts and disconnect the 6 connectors and 12 wire harness clamps.
46.SECURE STEERING WHEEL
45259A
47.REMOVE COLUMN HOLE COVER SILENCER SHEET (for LHD)
45259A
48.REMOVE COLUMN HOLE COVER SILENCER SHEET (for RHD)
45260
49.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (for LHD)
45260
50.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (for RHD)
45025D
51.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
51442A
52.REMOVE FRONT NO. 3 ENGINE UNDER COVER
57533B
53.REMOVE FRONT CENTER FLOOR BRACE
17410
54.REMOVE FRONT EXHAUST PIPE ASSEMBLY
43502H
55.REMOVE FRONT AXLE SHAFT NUT LH
43501H
56.REMOVE FRONT AXLE SHAFT NUT RH
Perform the same procedure as for the LH side.
89543
57.SEPARATE FRONT SPEED SENSOR LH
89542
58.SEPARATE FRONT SPEED SENSOR RH
Perform the same procedure as for the LH side.
45047
59.SEPARATE TIE ROD END SUB-ASSEMBLY LH
45046
60.SEPARATE TIE ROD END SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
48810
61.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH
48820B
62.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH
Perform the same procedure as for the LH side.
48069
63.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
48068
64.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
43420
65.SEPARATE FRONT DRIVE SHAFT ASSEMBLY LH
43420
66.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH
43410
67.SEPARATE FRONT DRIVE SHAFT ASSEMBLY RH
Perform the same procedure as for the LH side.
43410
68.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH
Perform the same procedure as for the LH side.
43420G
69.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH
43410N
70.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING RH
Perform the same procedure as for the LH side.
71.INSTALL ENGINE HANGERS
Install the 2 engine hangers with the 2 bolts.
| Part Name | Part No. |
|---|---|
| No. 1 Engine Hanger | 12281-37021 |
| No. 2 Engine Hanger | 12282-37011 |
| Bolt | 91552-81050 |
Attach a sling device to the engine hangers and a chain block.
28193
72.REMOVE STARTER HOLE INSULATOR
Remove the 2 bolts and starter hole insulator from the engine.
11363A
73.REMOVE FLYWHEEL HOUSING SIDE COVER
Remove the flywheel housing side cover from the engine.
51425A
74.REMOVE FRONT ENGINE MOUNTING BRACKET LOWER REINFORCEMENT
51108A
75.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH
51107A
76.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
52258A
77.REMOVE FRONT SUSPENSION MEMBER REAR BRACE LH
52257
78.REMOVE FRONT SUSPENSION MEMBER REAR BRACE RH
Perform the same procedure as for the LH side.
51201
79.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
12371A
80.REMOVE REAR ENGINE MOUNTING INSULATOR
30900
81.SUPPORT HYBRID VEHICLE TRANSAXLE ASSEMBLY
Support the hybrid vehicle transaxle assembly with a transmission jack.
57104E
82.REMOVE FRONT CROSSMEMBER SUB-ASSEMBLY
Remove the bolt and nut from the front engine mounting insulator.
Remove the 4 bolts and front crossmember sub-assembly from the body.
12361A
83.REMOVE FRONT ENGINE MOUNTING INSULATOR
12325A
84.REMOVE ENGINE MOUNTING BRACKET LH
Remove the bolt and nut, and separate the engine mounting insulator LH.
Turn the nut while holding the bolt.
Remove the 3 bolts and engine mounting bracket LH from the hybrid vehicle transaxle assembly.
30900
85.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY
Remove the 7 bolts and hybrid vehicle transaxle assembly from the engine.
To avoid damage to the knock pins, do not pry between the hybrid vehicle transaxle assembly and the engine.
To prevent the splines of the transmission input damper from becoming misaligned, do not allow the hybrid vehicle transaxle assembly to hit the transmission input damper during hybrid vehicle transaxle assembly removal and installation.
12311A
86.REMOVE FRONT ENGINE MOUNTING BRACKET
Remove the 3 bolts and front engine mounting bracket from the hybrid vehicle transaxle assembly.
12321A
87.REMOVE REAR ENGINE MOUNTING BRACKET
Remove the 4 bolts and rear engine mounting bracket from the hybrid vehicle transaxle assembly.
G2148
88.REMOVE GENERATOR CABLE
G1148
89.REMOVE MOTOR CABLE
90.REMOVE WIRE HARNESS CLAMP BRACKET
Remove the 2 bolts and 2 wire harness clamp brackets from the hybrid vehicle transaxle assembly.
G1143
91.REMOVE MOTOR CABLE BRACKET
Remove the bolt and motor cable bracket from the hybrid vehicle transaxle assembly.