After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
This section describes the standard values for all CAN related components.
The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM
Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
NO. 1 CAN JUNCTION CONNECTOR
Check the No. 1 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | for No. 7 CAN Junction Connector |
| *c | for Certification ECU (Smart Key ECU Assembly) | *d | for No. 5 CAN Junction Connector |
| *e | for Main Body ECU (Multiplex Network Body ECU) | *f | for Air Conditioning Amplifier Assembly |
| *g | for No. 4 CAN Junction Connector | *h | for No. 6 CAN Junction Connector |
| *i | for Steering Sensor | - | - |
Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| G96-1 (CANH) | P | No. 7 CAN junction connector |
| G96-12 (CANL) | W | |
| G96-2 (CANH) | G | Certification ECU (smart key ECU assembly) |
| G96-13 (CANL) | W | |
| G96-3 (CANH) | W | No. 5 CAN junction connector |
| G96-14 (CANL) | L | |
| G96-4 (CANH) | BE | Main body ECU (multiplex network body ECU) |
| G96-15 (CANL) | V | |
| G96-5 (CANH) | SB | Air conditioning amplifier assembly |
| G96-16 (CANL) | W | |
| G96-9 (CANH) | SB | No. 4 CAN junction connector |
| G96-20 (CANL) | W | |
| G96-10 (CANH) | R | No. 6 CAN junction connector |
| G96-21 (CANL) | W | |
| G96-11 (CANH) | G | Steering sensor |
| G96-22 (CANL) | W |
NO. 2 CAN JUNCTION CONNECTOR
Check the No. 2 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | for Millimeter Wave Radar Sensor Assembly (w/ Pre-collision System) |
| *c | for No. 8 CAN Junction Connector | *d | for Swing Grille Actuator Assembly (w/ Grille Shutter System) |
| *e | for Parking Assist ECU (w/ Panoramic View Monitor System) | *f | for Forward Recognition Camera (w/ Pre-collision System) |
| *g | for Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System) | *h | for Central Gateway ECU (Network Gateway ECU) |
Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
|
*1: w/ Pre-collision System *2: w/ Grille Shutter System *3: w/ Panoramic View Monitor System *4: w/ TOYOTA Parking Assist-sensor System |
||
| G102-2 (CANH) | R | Millimeter wave radar sensor assembly*1 |
| G102-12 (CANL) | W | |
| G102-3 (CANH) | B | No. 8 CAN junction connector |
| G102-13 (CANL) | W | |
| G102-4 (CANH) | G | Swing grille actuator assembly*2 |
| G102-14 (CANL) | W | |
| G102-5 (CANH) | GR | Parking assist ECU*3 |
| G102-15 (CANL) | W | |
| G102-6 (CANH) | L | Forward recognition camera*1 |
| G102-16 (CANL) | B | |
| G102-7 (CANH) | L | Clearance warning ECU assembly*4 |
| G102-17 (CANL) | W | |
| G102-8 (CANH) | P | Central gateway ECU (network gateway ECU) |
| G102-18 (CANL) | W | |
NO. 3 CAN JUNCTION CONNECTOR
Check the No. 3 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
*b | for Central Gateway ECU (Network Gateway ECU) |
| *c | for Inverter with Converter Assembly (for 4WD/AWD) | *d | for ECM |
| *e | for Inverter with Converter Assembly | *f | for Hybrid Vehicle Control ECU Assembly |
| *g | for Brake Booster with Master Cylinder Assembly (Skid Control ECU) | *h | for Vehicle Approaching Speaker Controller (w/ Vehicle Proximity Notification System) |
| *i | for Battery ECU Assembly (for LITHIUM-ION BATTERY) | - | - |
Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
|
*1: for 4WD/AWD *2: w/ Vehicle Proximity Notification System *3: for LITHIUM-ION BATTERY |
||
| G103-1 (CANH) | SB | Central gateway ECU (network gateway ECU) |
| G103-11 (CANL) | W | |
| G103-2 (CANH)*1 | LG | Inverter with converter assembly |
| G103-12 (CANL)*1 | W | |
| G103-3 (CANH) | G | ECM |
| G103-13 (CANL) | W | |
| G103-4 (CANH) | V | Inverter with converter assembly |
| G103-14 (CANL) | W | |
| G103-5 (CANH) | L | Hybrid vehicle control ECU assembly |
| G103-15 (CANL) | W | |
| G103-7 (CANH) | L | Brake booster with master cylinder assembly (skid control ECU) |
| G103-17 (CANL) | W | |
| G103-8 (CANH) | P | Vehicle approaching speaker controller*2 |
| G103-18 (CANL) | W | |
| G103-10 (CANH) | V | Battery ECU assembly*3 |
| G103-20 (CANL) | W | |
NO. 4 CAN JUNCTION CONNECTOR
Check the No. 4 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
*b | for Brake Booster with Master Cylinder Assembly (Skid Control ECU) |
| *c | for Airbag Sensor Assembly | *d | for Hybrid Vehicle Control ECU Assembly |
| *e | for No. 1 CAN Junction Connector | *f | for Rack and Pinion Power Steering Gear Assembly |
| *g | for ECM | - | - |
Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| G104-1 (CANH) | Y | Brake booster with master cylinder assembly (skid control ECU) |
| G104-7 (CANL) | W | |
| G104-2 (CANH) | R | Airbag sensor assembly |
| G104-8 (CANL) | W | |
| G104-3 (CANH) | G | Hybrid vehicle control ECU assembly |
| G104-9 (CANL) | W | |
| G104-4 (CANH) | SB | No. 1 CAN junction connector |
| G104-10 (CANL) | W | |
| G104-5 (CANH) | G | Rack and pinion power steering gear assembly |
| G104-11 (CANL) | W | |
| G104-6 (CANH) | P | ECM |
| G104-12 (CANL) | W |
NO. 5 CAN JUNCTION CONNECTOR
Check the No. 5 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
*b | for Bus Buffer ECU (w/ Bus Buffer ECU) |
| *c | for Central Gateway ECU (Network Gateway ECU) | *d | for Telephone Transceiver Assembly (w/ Telematics System) |
| *e | for Central Gateway ECU (Network Gateway ECU) | *f | for Radio and Display Receiver Assembly (for Radio and Display Type) |
| *g | for Position Control ECU Assembly (for RHD with Memory) | *h | for No. 1 CAN Junction Connector |
| *i | for Headlight ECU Sub-assembly RH | *j | for Central Gateway ECU (Network Gateway ECU) |
Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
|
*1: w/ Bus Buffer ECU *2: w/ Telematics System *3: for Radio and Display Type *4: for RHD with Memory |
||
| G105-1 (CANH) | LG | Bus buffer ECU*1 |
| G105-12 (CANL) | W | |
| G105-2 (CANH) | B | Central gateway ECU (network gateway ECU) |
| G105-13 (CANL) | W | |
| G105-3 (CANH) | R | Telephone transceiver assembly*2 |
| G105-14 (CANL) | W | |
| G105-4 (CANH) | G | Central gateway ECU (network gateway ECU) |
| G105-15 (CANL) | W | |
| G105-5 (CANH) | B | Radio and display receiver assembly*3 |
| G105-16 (CANL) | W | |
| G105-8 (CANH) | G | Position control ECU assembly*4 |
| G105-19 (CANL) | W | |
| G105-9 (CANH) | W | No. 1 CAN junction connector |
| G105-20 (CANL) | L | |
| G105-10 (CANH) | G | Headlight ECU sub-assembly RH |
| G105-21 (CANL) | W | |
| G105-11 (CANH) | LG | Central gateway ECU (network gateway ECU) |
| G105-22 (CANL) | W | |
NO. 6 CAN JUNCTION CONNECTOR
Check the No. 6 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 6 CAN Junction Connector) |
*b | for Occupant Detection ECU (w/ Occupant Classification System) |
| *c | for Central Gateway ECU (Network Gateway ECU) | *d | for No. 1 CAN Junction Connector |
| *e | for Parking Brake ECU Assembly | - | - |
Check the connection diagram of the components which are connected to the No. 6 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
|
*: w/ Occupant Classification System |
||
| M31-2 (CANH) | GR | Occupant detection ECU* |
| M31-8 (CANL) | W | |
| M31-3 (CANH) | G | Central gateway ECU (network gateway ECU) |
| M31-9 (CANL) | W | |
| M31-4 (CANH) | LG | No. 1 CAN junction connector |
| M31-10 (CANL) | W | |
| M31-5 (CANH) | R | Parking brake ECU assembly |
| M31-11 (CANL) | W | |
NO. 7 CAN JUNCTION CONNECTOR
Check the No. 7 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 7 CAN Junction Connector) |
*b | for No. 1 CAN Junction Connector |
| *c | for Combination Meter Assembly | *d | for Multiplex Network Door ECU (w/ Power Back Door System) |
| *e | for Position Control ECU Assembly (for LHD with Memory) | *f | for Headlight ECU Sub-assembly LH |
Check the connection diagram of the components which are connected to the No. 7 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
|
*1: w/ Power Back Door System *2: for LHD with Memory |
||
| N52-1 (CANH) | B | No. 1 CAN junction connector |
| N52-7 (CANL) | W | |
| N52-2 (CANH) | LG | Combination meter assembly |
| N52-8 (CANL) | W | |
| N52-3 (CANH) | L | Multiplex network door ECU*1 |
| N52-9 (CANL) | W | |
| N52-4 (CANH) | G | Position control ECU assembly*2 |
| N52-10 (CANL) | W | |
| N52-5 (CANH) | P | Headlight ECU sub-assembly LH |
| N52-11 (CANL) | W | |
NO. 8 CAN JUNCTION CONNECTOR
Check the No. 8 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 8 CAN Junction Connector) |
*b | for No. 2 CAN Junction Connector |
| *c | for Blind Spot Monitor Sensor LH (w/ Blind Spot Monitor System) | *d | for Television Camera Assembly (w/ Panoramic View Monitor System, w/ Parking Assist Monitor System) |
| *e | for No. 1 CAN Junction Terminal | - | - |
Check the connection diagram of the components which are connected to the No. 8 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
|
*1: w/ Blind Spot Monitor System *2: w/ Panoramic View Monitor System *3: w/ Parking Assist Monitor System |
||
| N53-1 (CANH) | SB | No. 2 CAN junction connector |
| N53-7 (CANL) | W | |
| N53-2 (CANH) | BE | Blind spot monitor sensor LH*1 |
| N53-8 (CANL) | W | |
| N53-3 (CANH) | R | Television camera assembly*2, *3 |
| N53-9 (CANL) | L | |
| N53-4 (CANH) | G | No. 1 CAN junction terminal |
| N53-10 (CANL) | W | |
NO. 1 CAN JUNCTION TERMINAL
Check the No. 1 CAN junction terminal.
| *a | Rear view of wire harness connector
(to No. 1 CAN Junction Terminal) |
| *b | for No. 8 CAN Junction Connector |
Connection diagram
Check the connection diagram of the components which are connected to the No. 1 CAN junction terminal.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| N54-3 (CANH) | G | No. 8 CAN junction connector |
| N54-2 (CANL) | W |
DLC3
Disconnect the cable from the negative (-) auxiliary battery terminal.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of DLC3 | - | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G114-6 (CANH) - G114-14 (CANL) | B - V | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| G114-6 (CANH) - G114-4 (CG) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G114-14 (CANL) - G114-4 (CG) | V - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G114-6 (CANH) - G114-16 (BAT) | B - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G114-14 (CANL) - G114-16 (BAT) | V - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
| *a | Component without harness connected
(Central Gateway ECU [Network Gateway ECU]) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the central gateway ECU (network gateway ECU) connector.
| *a | Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU]) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G72-14 (CA6H) - G72-5 (CA6L) | B - V | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher |
| G72-14 (CA6H) - G72-10 (GND) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G72-5 (CA6L) - G72-10 (GND) | V - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G72-14 (CA6H) - G72-1 (BATT) | B - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G72-5 (CA6L) - G72-1 (BATT) | V - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G72-23 (CA1H) - G72-8 (CA1L) | P - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| G72-23 (CA1H) - G72-10 (GND) | P - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G72-8 (CA1L) - G72-10 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G72-23 (CA1H) - G72-1 (BATT) | P - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G72-8 (CA1L) - G72-1 (BATT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G72-18 (CA4H) - G72-17 (CA4L) | SB - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| G72-18 (CA4H) - G72-10 (GND) | SB - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G72-17 (CA4L) - G72-10 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G72-18 (CA4H) - G72-1 (BATT) | SB - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G72-17 (CA4L) - G72-1 (BATT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G72-19 (CAYH) - G72-20 (CAYL) | G - W | HIGH-level CAN bus line - HIGH-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher |
| G72-19 (CAYH) - G72-6 (CA3H) | G - B | HIGH-level CAN bus line - HIGH-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| G72-20 (CAYL) - G72-21 (CA3L) | W - W | LOW-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| G72-19 (CAYH) - G72-10 (GND) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G72-20 (CAYL) - G72-10 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G72-19 (CAYH) - G72-1 (BATT) | G - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G72-20 (CAYL) - G72-1 (BATT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G72-22 (CA2H) - G72-7 (CA2L) | G - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| G72-22 (CA2H) - G72-10 (GND) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G72-7 (CA2L) - G72-10 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G72-22 (CA2H) - G72-1 (BATT) | G - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G72-7 (CA2L) - G72-1 (BATT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G72-15 (CA5H) - G72-16 (CA5L) | LG - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| G72-15 (CA5H) - G72-10 (GND) | LG - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G72-16 (CA5L) - G72-10 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G72-15 (CA5H) - G72-1 (BATT) | LG - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G72-16 (CA5L) - G72-1 (BATT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
ECM
Refer to Terminals of ECU.
A25A-FXS (w/ Canister Pump Module): Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>TERMINALS OF ECM
A25A-FXS (w/o Canister Pump Module): Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>TERMINALS OF ECM
A25B-FXS: Click hereEngine / Hybrid System>A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A24-8 (CANH) - A24-18 (CANL) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| A24-8 (CANH) - A24-10 (E1) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A24-18 (CANL) - A24-10 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A24-8 (CANH) - A24-1 (BATT) | B - G | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A24-18 (CANL) - A24-1 (BATT) | W - G | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A24-7 (CAN+) - A24-17 (CAN-) | P - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A24-7 (CAN+) - A24-10 (E1) | P - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A24-17 (CAN-) - A24-10 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A24-7 (CAN+) - A24-1 (BATT) | P - G | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A24-17 (CAN-) - A24-1 (BATT) | W - G | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
HYBRID VEHICLE CONTROL ECU ASSEMBLY
Refer to Terminals of ECU.
for 2WD with NICKEL METAL HYDRIDE BATTERY: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>TERMINALS OF ECU
for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>TERMINALS OF ECU
for 2WD with LITHIUM-ION BATTERY: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with LITHIUM-ION BATTERY)>TERMINALS OF ECU
for 4WD/AWD with LITHIUM-ION BATTERY: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with LITHIUM-ION BATTERY)>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the hybrid vehicle control ECU assembly connectors.
| *A | for LHD | *B | for RHD |
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A31-21 (CA1H) - A31-8 (CA1L) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| A31-21 (CA1H) - A30-3 (E1) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A31-8 (CA1L) - A30-3 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A31-21 (CA1H) - A30-27 (BATT) | L - B | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A31-8 (CA1L) - A30-27 (BATT) | W - B | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G64-21 (CA1H) - G64-8 (CA1L) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| G64-21 (CA1H) - G63-3 (E1) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G64-8 (CA1L) - G63-3 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G64-21 (CA1H) - G63-27 (BATT) | L - B | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G64-8 (CA1L) - G63-27 (BATT) | W - B | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A31-7 (CA3P) - A31-20 (CA3N) | G - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A31-7 (CA3P) - A30-3 (E1) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A31-20 (CA3N) - A30-3 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A31-7 (CA3P) - A30-27 (BATT) | G - B | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A31-20 (CA3N) - A30-27 (BATT) | W - B | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G64-7 (CA3P) - G64-20 (CA3N) | G - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| G64-7 (CA3P) - G63-3 (E1) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G64-20 (CA3N) - G63-3 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G64-7 (CA3P) - G63-27 (BATT) | G - B | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G64-20 (CA3N) - G63-27 (BATT) | W - B | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
INVERTER WITH CONVERTER ASSEMBLY
Refer to Terminals of ECU.
for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>TERMINALS OF ECU
for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the inverter with converter assembly connector.
| *A | for 2WD | *B | for 4WD/AWD |
| *a | Front view of wire harness connector
(to Inverter with Converter Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A51-1 (CANH) - A51-7 (CANL) | V - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A51-1 (CANH) - A51-24 (GND1) | V - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A51-7 (CANL) - A51-24 (GND1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A51-1 (CANH) - A51-6 (+B) | V - W | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A51-7 (CANL) - A51-6 (+B) | W - W | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A87-22 (CANH) - A87-31 (CANL) | V - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A87-22 (CANH) - A87-9 (GND1) | V - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A87-31 (CANL) - A87-9 (GND1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A87-22 (CANH) - A87-36 (+B) | V - W | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A87-31 (CANL) - A87-36 (+B) | W - W | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A87-24 (CNH2) - A87-33 (CNL2) | LG - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A87-24 (CNH2) - A87-9 (GND1) | LG - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A87-33 (CNL2) - A87-9 (GND1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A87-24 (CNH2) - A87-36 (+B) | LG - W | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A87-33 (CNL2) - A87-36 (+B) | W - W | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
BATTERY ECU ASSEMBLY (for LITHIUM-ION BATTERY)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Front view of wire harness connector
(to Battery ECU Assembly) |
Disconnect the battery ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| z26-29 (CA2H) - z26-28 (CA2L) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| z26-29 (CA2H) - z26-3 (GND1) | R - GR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| z26-28 (CA2L) - z26-3 (GND1) | W - GR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| z26-29 (CA2H) - z26-1 (AM) | R - BR | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| z26-28 (CA2L) - z26-1 (AM) | W - BR | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly [Skid Control ECU]) |
Disconnect the brake booster with master cylinder assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A42-35 (CA2H) - A42-34 (CA2L) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A42-35 (CA2H) - A42-27 (GND2) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A42-34 (CA2L) - A42-27 (GND2) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A42-35 (CA2H) - A42-14 (B1) | L - SB | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A42-34 (CA2L) - A42-14 (B1) | W - SB | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A42-37 (CA1H) - A42-38 (CA1L) | Y - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A42-37 (CA1H) - A42-27 (GND2) | Y - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A42-38 (CA1L) - A42-27 (GND2) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A42-37 (CA1H) - A42-14 (B1) | Y - SB | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A42-38 (CA1L) - A42-14 (B1) | W - SB | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
RACK AND PINION POWER STEERING GEAR ASSEMBLY
Refer to Terminals of ECU.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Front view of wire harness connector
(to Rack and Pinion Power Steering Gear Assembly) |
| *b | Front view of DLC3 |
Disconnect the rack and pinion power steering gear assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| C54-10 (CANH) - C54-11 (CANL) | G - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| C54-10 (CANH) - C54-7 (PGND) | G - B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| C54-11 (CANL) - C54-7 (PGND) | W - B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| C54-10 (CANH) - G114-16 (BAT) | G - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| C54-11 (CANL) - G114-16 (BAT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
PARKING BRAKE ECU ASSEMBLY
Refer to Terminals of ECU.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster)>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Front view of wire harness connector
(to Parking Brake ECU Assembly) |
Disconnect the parking brake ECU assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| M35-11 (CANH) - M35-1 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| M35-11 (CANH) - M36-9 (GND1) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M35-1 (CANL) - M36-9 (GND1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M35-11 (CANH) - M36-7 (+B) | R - W | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| M35-1 (CANL) - M36-7 (+B) | W - W | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
STEERING SENSOR
| *a | Component without harness connected
(Steering Sensor) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Front view of wire harness connector
(to Steering Sensor) |
Disconnect the steering sensor connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G68-3 (CANH) - G68-8 (CANL) | G - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| G68-3 (CANH) - G68-6 (ESS) | G - LA | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G68-8 (CANL) - G68-6 (ESS) | W - LA | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G68-3 (CANH) - G68-4 (BAT) | G - LA-B | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G68-8 (CANL) - G68-4 (BAT) | W - LA-B | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
FORWARD RECOGNITION CAMERA (w/ Pre-collision System)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the forward recognition camera connector.
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| P8-5 (CA1P) - P8-11 (CA1N) | L - B | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| P8-5 (CA1P) - P8-10 (GND) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| P8-11 (CA1N) - P8-10 (GND) | B - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| P8-5 (CA1P) - G114-16 (BAT) | L - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| P8-11 (CA1N) - G114-16 (BAT) | B - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-collision System)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT RADAR SENSOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the millimeter wave radar sensor assembly connector.
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| B9-3 (CA2H) - B9-2 (CA2L) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| B9-3 (CA2H) - B9-1 (SGND) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| B9-2 (CA2L) - B9-1 (SGND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| B9-3 (CA2H) - G114-16 (BAT) | R - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| B9-2 (CA2L) - G114-16 (BAT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
AIRBAG SENSOR ASSEMBLY
Refer to Terminals of ECU.
w/ Occupant Classification System: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>TERMINALS OF ECU
w/o Occupant Classification System: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Disconnect the airbag sensor assembly connector.
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G70-26 (CANH) - G70-27 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| G70-26 (CANH) - G70-33 (E1) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G70-27 (CANL) - G70-33 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G70-26 (CANH) - G114-16 (BAT) | R - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G70-27 (CANL) - G114-16 (BAT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
COMBINATION METER ASSEMBLY
Refer to Terminals of ECU.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G18-9 (CANH) - G18-25 (CANL) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| G18-9 (CANH) - G18-23 (ES) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G18-25 (CANL) - G18-23 (ES) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G18-9 (CANH) - G18-22 (B) | B - B | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G18-25 (CANL) - G18-22 (B) | W - B | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
Refer to Terminals of ECU.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU]) |
| *b | Front view of DLC3 |
Disconnect the main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G44-5 (CANH) - G44-4 (CANL) | BE - V | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| G44-5 (CANH) - G114-4 (CG) | BE - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G44-4 (CANL) - G114-4 (CG) | V - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G44-5 (CANH) - G114-16 (BAT) | BE - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G44-4 (CANL) - G114-16 (BAT) | V - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the radio and display receiver assembly connectors.
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G2-13 (CANH) - G2-14 (CANL) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| G2-13 (CANH) - G3-1 (GND1) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G2-14 (CANL) - G3-1 (GND1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G2-13 (CANH) - G3-4 (+B1) | B - LG | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G2-14 (CANL) - G3-4 (+B1) | W - LG | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
TELEPHONE TRANSCEIVER ASSEMBLY (w/ Telematics System for ERA-GLONASS)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Front view of wire harness connector
(to Telephone Transceiver Assembly) |
Disconnect the telephone transceiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| H6-15 (CANP) - H6-16 (CANN) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H6-15 (CANP) - H6-4 (E) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H6-16 (CANN) - H6-4 (E) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H6-15 (CANP) - H6-1 (+B) | R - B | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H6-16 (CANN) - H6-1 (+B) | W - B | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
TELEPHONE TRANSCEIVER ASSEMBLY (w/ Telematics System for eCall)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Front view of wire harness connector
(to Telephone Transceiver Assembly) |
Disconnect the telephone transceiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| H10-25 (CANP) - H10-26 (CANN) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H10-25 (CANP) - H10-20 (E) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H10-26 (CANN) - H10-20 (E) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H10-25 (CANP) - H10-1 (+B) | R - B | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H10-26 (CANN) - H10-1 (+B) | W - B | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
AIR CONDITIONING AMPLIFIER ASSEMBLY
Refer to Terminals of ECU.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for HV Model)>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Disconnect the air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G46-2 (CANH) - G46-1 (CANL) | SB - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| G46-2 (CANH) - G46-17 (GND) | SB - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G46-1 (CANL) - G46-17 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G46-2 (CANH) - G46-5 (B) | SB - G | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G46-1 (CANL) - G46-5 (B) | W - G | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System, w/ Parking Assist Monitor System)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the television camera assembly connector.
| *a | Front view of wire harness connector
(to Television Camera Assembly) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| R15-4 (CANH) - R15-1 (CANL) | R - L | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| R15-4 (CANH) - G114-4 (CG) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| R15-1 (CANL) - G114-4 (CG) | L - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| R15-4 (CANH) - G114-16 (BAT) | R - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| R15-1 (CANL) - G114-16 (BAT) | L - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the clearance warning ECU assembly connector.
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| H4-17 (R1) - H4-18 (R2) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H4-17 (R1) - H4-28 (E) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H4-18 (R2) - H4-28 (E) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H4-17 (R1) - G114-16 (BAT) | L - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H4-18 (R2) - G114-16 (BAT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the blind spot monitor sensor LH connector.
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| Q1-2 (CA1P) - Q1-7 (CA1N) | G - SB | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Q1-2 (CA1P) - Q1-10 (BLGD) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| Q1-7 (CA1N) - Q1-10 (BLGD) | SB - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| Q1-2 (CA1P) - G114-16 (BAT) | G - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Q1-7 (CA1N) - G114-16 (BAT) | SB - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly]) |
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G54-1 (CANH) - G54-2 (CANL) | G - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| G54-1 (CANH) - G54-18 (E) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G54-2 (CANL) - G54-18 (E) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G54-1 (CANH) - G54-4 (+B) | G - P | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G54-2 (CANL) - G54-4 (+B) | W - P | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
HEADLIGHT ECU SUB-ASSEMBLY LH
Refer to Terminals of ECU.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Front view of wire harness connector
(to Headlight ECU Sub-assembly LH) |
| *b | Front view of DLC3 |
Disconnect the headlight ECU sub-assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A11-24 (CANH) - A11-23 (CANL) | P - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A11-24 (CANH) - A11-12 (GND) | P - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A11-23 (CANL) - A11-12 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A11-24 (CANH) - G114-16 (BAT) | P - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A11-23 (CANL) - G114-16 (BAT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
HEADLIGHT ECU SUB-ASSEMBLY RH
Refer to Terminals of ECU.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Front view of wire harness connector
(to Headlight ECU Sub-assembly RH) |
| *b | Front view of DLC3 |
Disconnect the headlight ECU sub-assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A12-24 (CANH) - A12-23 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A12-24 (CANH) - A12-12 (GND) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A12-23 (CANL) - A12-12 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A12-24 (CANH) - G114-16 (BAT) | L - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A12-23 (CANL) - G114-16 (BAT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
POSITION CONTROL ECU ASSEMBLY (w/ Memory)
Refer to Terminals of ECU.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *A | for LHD |
| *B | for RHD |
| *a | Front view of wire harness connector
(to Position Control ECU Assembly) |
Disconnect the position control ECU assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| T8-13 (CANP) - T8-14 (CANN) | LG - R | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| T8-13 (CANP) - T7-2 (GND) | LG - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| T8-14 (CANN) - T7-2 (GND) | R - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| T8-13 (CANP) - T7-3 (+B) | LG - W | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| T8-14 (CANN) - T7-3 (+B) | R - W | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| S8-13 (CANP) - S8-14 (CANN) | LG - R | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| S8-13 (CANP) - S7-2 (GND) | LG - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| S8-14 (CANN) - S7-2 (GND) | R - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| S8-13 (CANP) - S7-3 (+B) | LG - W | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| S8-14 (CANN) - S7-3 (+B) | R - W | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
BUS BUFFER ECU (w/ Bus Buffer ECU)
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the bus buffer ECU connector.
| *a | Front view of wire harness connector
(to Bus Buffer ECU) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G80-2 (CAN+) - G80-1 (CAN-) | LG - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| G80-2 (CAN+) - G114-4 (CG) | LG - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G80-1 (CAN-) - G114-4 (CG) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G80-2 (CAN+) - G114-16 (BAT) | LG - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G80-1 (CAN-) - G114-16 (BAT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
OCCUPANT DETECTION ECU (w/ Occupant Classification System)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the occupant detection ECU connector.
| *a | Front view of wire harness connector
(to Occupant Detection ECU) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| S21-5 - S21-4 | R - SB | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| S21-5 - S21-10 | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| S21-4 - S21-10 | SB - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| S21-5 - G114-16 (BAT) | R - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| S21-4 - G114-16 (BAT) | SB - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
SWING GRILLE ACTUATOR ASSEMBLY (w/ Grille Shutter System)
Refer to Terminals of ECU.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER SYSTEM (for HV Model)>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the swing grille actuator assembly connector.
| *A | w/o Canister Pump Module |
| *B | w/ Canister Pump Module |
| *a | Front view of wire harness connector
(to Swing Grille Actuator Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A50-2 (CANP) - A50-3 (CANN) | G - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A50-2 (CANP) - A50-1 (GND) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A50-3 (CANN) - A50-1 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A50-2 (CANP) - A50-4 (+B) | G - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A50-3 (CANN) - A50-4 (+B) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A85-6 (CANP) - A85-5 (CANN) | G - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A85-6 (CANP) - A85-3 (GND) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A85-5 (CANN) - A85-3 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A85-6 (CANP) - A85-1 (+B) | G - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A85-5 (CANN) - A85-1 (+B) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
MULTIPLEX NETWORK DOOR ECU (w/ Power Back Door System)
Refer to Terminals of ECU.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for HV Model)>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the multiplex network door ECU connectors.
| *a | Front view of wire harness connector
(to Multiplex Network Door ECU) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| R18-39 (CANP) - R18-40 (CANN) | L - R | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| R18-39 (CANP) - R19-10 (GND) | L - W | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| R18-40 (CANN) - R19-10 (GND) | R - W | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| R18-39 (CANP) - R19-1 (B) | L - W | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| R18-40 (CANN) - R19-1 (B) | R - W | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
PARKING ASSIST ECU (w/ Panoramic View Monitor System)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the parking assist ECU connector.
| *a | Front view of wire harness connector
(to Parking Assist ECU) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| N25-11 (CANH) - N25-12 (CANL) | GR - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| N25-11 (CANH) - N25-4 (GND1) | GR - LA | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| N25-12 (CANL) - N25-4 (GND1) | W - LA | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| N25-11 (CANH) - N25-1 (+B) | GR - L | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| N25-12 (CANL) - N25-1 (+B) | W - L | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
VEHICLE APPROACHING SPEAKER CONTROLLER (w/ Vehicle Proximity Notification System)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the vehicle approaching speaker controller connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Vehicle Approaching Speaker Controller) |
*b | Front view of DLC3 |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A45-3 (CANH) - A45-4 (CANL) | P - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A45-3 (CANH) - A45-6 (GND) | P - LA | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A45-4 (CANL) - A45-6 (GND) | W - LA | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A45-3 (CANH) - G114-16 (BAT) | P - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A45-4 (CANL) - G114-16 (BAT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |