After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
This section describes the standard values for all CAN related components.
The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
NO. 1 CAN JUNCTION CONNECTOR
Check the No. 1 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | for No. 7 CAN Junction Connector |
| *c | for Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System) | *d | for No. 5 CAN Junction Connector |
| *e | for Main Body ECU (Multiplex Network Body ECU) | *f | for Air Conditioning Amplifier Assembly |
| *g | for No. 4 CAN Junction Connector | *h | for No. 6 CAN Junction Connector |
| *i | for Steering Sensor | - | - |
Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.
| Terminal No. | Wiring Color | Connected to |
|---|---|---|
|
*: w/ Entry and Start System |
||
| G96-1 (CANH) | P | No. 7 CAN junction connector |
| G96-12 (CANL) | W | |
| G96-2 (CANH) | G | Certification ECU (smart key ECU assembly)* |
| G96-13 (CANL) | W | |
| G96-3 (CANH) | W | No. 5 CAN junction connector |
| G96-14 (CANL) | L | |
| G96-4 (CANH) | BE | Main body ECU (multiplex network body ECU) |
| G96-15 (CANL) | V | |
| G96-5 (CANH) | SB | Air conditioning amplifier assembly |
| G96-16 (CANL) | W | |
| G96-9 (CANH) | SB | No. 4 CAN junction connector |
| G96-20 (CANL) | W | |
| G96-10 (CANH) | R | No. 6 CAN junction connector |
| G96-21 (CANL) | W | |
| G96-11 (CANH) | G | Steering sensor |
| G96-22 (CANL) | W | |
NO. 2 CAN JUNCTION CONNECTOR
Check the No. 2 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | for Millimeter Wave Radar Sensor Assembly (w/ Pre-collision System) |
| *c | for No. 8 CAN Junction Connector | *d | for Swing Grille Actuator Assembly (w/ Grille Shutter System) |
| *e | for Parking Assist ECU (w/ Panoramic View Monitor System) | *f | for Forward Recognition Camera (w/ Pre-collision System) |
| *g | for Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System) | *h | for Central Gateway ECU (Network Gateway ECU) |
Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
|
*1: w/ Pre-collision System *2: w/ Grille Shutter System *3: w/ Panoramic View Monitor System *4: w/ TOYOTA Parking Assist-sensor System |
||
| G102-2 (CANH) | R | Millimeter wave radar sensor assembly*1 |
| G102-12 (CANL) | W | |
| G102-3 (CANH) | B | No. 8 CAN junction connector |
| G102-13 (CANL) | W | |
| G102-4 (CANH) | G | Swing grille actuator assembly*2 |
| G102-14 (CANL) | W | |
| G102-5 (CANH) | GR | Parking assist ECU*3 |
| G102-15 (CANL) | W | |
| G102-6 (CANH) | L | Forward recognition camera*1 |
| G102-16 (CANL) | B | |
| G102-7 (CANH) | L | Clearance warning ECU assembly*4 |
| G102-17 (CANL) | W | |
| G102-8 (CANH) | P | Central gateway ECU (network gateway ECU) |
| G102-18 (CANL) | W | |
NO. 3 CAN JUNCTION CONNECTOR
Check the No. 3 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
*b | for Central Gateway ECU (Network Gateway ECU) |
| *c | for ECM | *d | for Engine Stop and Start ECU (w/ Stop and Start System) |
| *e | for Transmission Control ECU (for CVT) | - | - |
Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
|
*1: w/ Stop and Start System *2: for CVT |
||
| G103-1 (CANH) | SB | Central gateway ECU (network gateway ECU) |
| G103-11 (CANL) | W | |
| G103-3 (CANH) | G | ECM |
| G103-13 (CANL) | W | |
| G103-6 (CANH) | R | Engine stop and start ECU*1 |
| G103-16 (CANL) | W | |
| G103-9 (CANH) | L | Transmission control ECU*2 |
| G103-19 (CANL) | W | |
NO. 4 CAN JUNCTION CONNECTOR
Check the No. 4 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
*b | for Brake Actuator Assembly (Skid Control ECU) |
| *c | for Airbag Sensor Assembly | *d | for 4WD ECU Assembly (for 4WD/AWD) |
| *e | for No. 1 CAN Junction Connector | *f | for Rack and Pinion Power Steering Gear Assembly |
Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
|
*: for 4WD/AWD |
||
| G104-1 (CANH) | Y | Brake actuator assembly (skid control ECU) |
| G104-7 (CANL) | W | |
| G104-2 (CANH) | R | Airbag sensor assembly |
| G104-8 (CANL) | W | |
| G104-3 (CANH) | W | 4WD ECU assembly* |
| G104-9 (CANL) | R | |
| G104-4 (CANH) | SB | No. 1 CAN junction connector |
| G104-10 (CANL) | W | |
| G104-5 (CANH) | G | Rack and pinion power steering gear assembly |
| G104-11 (CANL) | W | |
NO. 5 CAN JUNCTION CONNECTOR
Check the No. 5 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
*b | for Bus Buffer ECU (w/ Bus Buffer ECU) |
| *c | for Central Gateway ECU (Network Gateway ECU) | *d | for Telephone Transceiver Assembly (w/ Telematics System) |
| *e | for Central Gateway ECU (Network Gateway ECU) | *f | for Radio and Display Receiver Assembly (for Radio and Display Type) |
| *g | for Position Control ECU Assembly (for RHD with Memory) | *h | for No. 1 CAN Junction Connector |
| *i | for Headlight ECU Sub-assembly RH | *j | for Central Gateway ECU (Network Gateway ECU) |
Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.
| Terminal No. | Wiring Color | Connected to |
|---|---|---|
|
*1: w/ Bus Buffer ECU *2: w/ Telematics System *3: for Radio and Display Type *4: for RHD with Memory |
||
| G105-1 (CANH) | LG | Bus buffer ECU*1 |
| G105-12 (CANL) | W | |
| G105-2 (CANH) | B | Central gateway ECU (network gateway ECU) |
| G105-13 (CANL) | W | |
| G105-3 (CANH) | R | Telephone transceiver assembly*2 |
| G105-14 (CANL) | W | |
| G105-4 (CANH) | G | Central gateway ECU (network gateway ECU) |
| G105-15 (CANL) | W | |
| G105-5 (CANH) | B | Radio and display receiver assembly*3 |
| G105-16 (CANL) | W | |
| G105-8 (CANH) | G | Position control ECU assembly*4 |
| G105-19 (CANL) | W | |
| G105-9 (CANH) | W | No. 1 CAN junction connector |
| G105-20 (CANL) | L | |
| G105-10 (CANH) | G | Headlight ECU sub-assembly RH |
| G105-21 (CANL) | W | |
| G105-11 (CANH) | LG | Central gateway ECU (network gateway ECU) |
| G105-22 (CANL) | W | |
NO. 6 CAN JUNCTION CONNECTOR
Check the No. 6 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 6 CAN Junction Connector) |
*b | for Occupant Detection ECU (w/ Occupant Classification System) |
| *c | for Central Gateway ECU (Network Gateway ECU) | *d | for No. 1 CAN Junction Connector |
Check the connection diagram of the components which are connected to the No. 6 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
|
*: w/ Occupant Classification System |
||
| M31-2 (CANH) | GR | Occupant detection ECU* |
| M31-8 (CANL) | W | |
| M31-3 (CANH) | G | Central gateway ECU (network gateway ECU) |
| M31-9 (CANL) | W | |
| M31-4 (CANH) | LG | No. 1 CAN junction connector |
| M31-10 (CANL) | W | |
NO. 7 CAN JUNCTION CONNECTOR
Check the No. 7 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 7 CAN Junction Connector) |
*b | for No. 1 CAN Junction Connector |
| *c | for Combination Meter Assembly | *d | for Multiplex Network Door ECU (w/ Power Back Door System) |
| *e | for Position Control ECU Assembly (for LHD with Memory) | *f | for Headlight ECU Sub-assembly LH |
Check the connection diagram of the components which are connected to the No. 7 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
|
*1: w/ Power Back Door System *2: for LHD with Memory |
||
| N52-1 (CANH) | B | No. 1 CAN junction connector |
| N52-7 (CANL) | W | |
| N52-2 (CANH) | LG | Combination meter assembly |
| N52-8 (CANL) | W | |
| N52-3 (CANH) | L | Multiplex network door ECU*1 |
| N52-9 (CANL) | W | |
| N52-4 (CANH) | G | Position control ECU assembly*2 |
| N52-10 (CANL) | W | |
| N52-5 (CANH) | P | Headlight ECU sub-assembly LH |
| N52-11 (CANL) | W | |
NO. 8 CAN JUNCTION CONNECTOR
Check the No. 8 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 8 CAN Junction Connector) |
*b | for No. 2 CAN Junction Connector |
| *c | for Blind Spot Monitor Sensor LH (w/ Blind Spot Monitor System) | *d | for Television Camera Assembly (w/ Panoramic View Monitor System, w/ Parking Assist Monitor System) |
| *e | for No. 1 CAN Junction Terminal | - | - |
Check the connection diagram of the components which are connected to the No. 8 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
|
*1: w/ Blind Spot Monitor System *2: w/ Panoramic View Monitor System *3: w/ Parking Assist Monitor System |
||
| N53-1 (CANH) | SB | No. 2 CAN junction connector |
| N53-7 (CANL) | W | |
| N53-2 (CANH) | BE | Blind spot monitor sensor LH*1 |
| N53-8 (CANL) | W | |
| N53-3 (CANH) | R | Television camera assembly*2, *3 |
| N53-9 (CANL) | L | |
| N53-4 (CANH) | G | No. 1 CAN junction terminal |
| N53-10 (CANL) | W | |
NO. 1 CAN JUNCTION TERMINAL
Check the No. 1 CAN junction terminal.
| *a | Rear view of wire harness connector
(to No. 1 CAN Junction Terminal) |
| *b | for No. 8 CAN Junction Connector |
Connection diagram
Check the connection diagram of the components which are connected to the No. 1 CAN junction terminal.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| N54-3 (CANH) | G | No. 8 CAN junction connector |
| N54-2 (CANL) | W |
DLC3
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of DLC3 | - | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G114-6 (CANH) - G114-14 (CANL) | B - V | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G114-6 (CANH) - G114-4 (CG) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G114-14 (CANL) - G114-4 (CG) | V - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G114-6 (CANH) - G114-16 (BAT) | B - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G114-14 (CANL) - G114-16 (BAT) | V - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
| *a | Component without harness connected
(Central Gateway ECU [Network Gateway ECU]) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the central gateway ECU (network gateway ECU) connector.
| *a | Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU]) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G72-14 (CA6H) - G72-5 (CA6L) | B - V | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| G72-14 (CA6H) - G72-10 (GND) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G72-5 (CA6L) - G72-10 (GND) | V - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G72-14 (CA6H) - G72-1 (BATT) | B - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G72-5 (CA6L) - G72-1 (BATT) | V - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G72-23 (CA1H) - G72-8 (CA1L) | P - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| G72-23 (CA1H) - G72-10 (GND) | P - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G72-8 (CA1L) - G72-10 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G72-23 (CA1H) - G72-1 (BATT) | P - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G72-8 (CA1L) - G72-1 (BATT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G72-18 (CA4H) - G72-17 (CA4L) | SB - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| G72-18 (CA4H) - G72-10 (GND) | SB - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G72-17 (CA4L) - G72-10 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G72-18 (CA4H) - G72-1 (BATT) | SB - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G72-17 (CA4L) - G72-1 (BATT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G72-19 (CAYH) - G72-20 (CAYL) | G - W | HIGH-level CAN bus line - HIGH-level CAN bus line | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| G72-19 (CAYH) - G72-6 (CA3H) | G - B | HIGH-level CAN bus line - HIGH-level CAN bus line | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
| G72-20 (CAYL) - G72-21 (CA3L) | W - W | LOW-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
| G72-19 (CAYH) - G72-10 (GND) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G72-20 (CAYL) - G72-10 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G72-19 (CAYH) - G72-1 (BATT) | G - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G72-20 (CAYL) - G72-1 (BATT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G72-22 (CA2H) - G72-7 (CA2L) | G - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| G72-22 (CA2H) - G72-10 (GND) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G72-7 (CA2L) - G72-10 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G72-22 (CA2H) - G72-1 (BATT) | G - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G72-7 (CA2L) - G72-1 (BATT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G72-15 (CA5H) - G72-16 (CA5L) | LG - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| G72-15 (CA5H) - G72-10 (GND) | LG - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G72-16 (CA5L) - G72-10 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G72-15 (CA5H) - G72-1 (BATT) | LG - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G72-16 (CA5L) - G72-1 (BATT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
ECM
Refer to Terminals of ECU.
for A25A-FKS with Canister Pump Module: Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>TERMINALS OF ECM
for A25A-FKS without Canister Pump Module: Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>TERMINALS OF ECM
for M20A-FKS: Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A24-8 (CANH) - A24-18 (CANL) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| A24-8 (CANH) - A24-10 (E1) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A24-18 (CANL) - A24-10 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A24-8 (CANH) - A24-1 (BATT) | B - G | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A24-18 (CANL) - A24-1 (BATT) | W - G | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
ENGINE STOP AND START ECU
Refer to Terminals of ECU.
for A25A-FKS: Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>TERMINALS OF ECU
for M20A-FKS: Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the engine stop and start ECU connectors.
| *A | for LHD | *B | for RHD |
| *a | Front view of wire harness connector
(to Engine Stop and Start ECU) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A32-13 (CANH) - A32-14 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A32-13 (CANH) - A33-8 (GND1) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A32-14 (CANL) - A33-8 (GND1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A32-13 (CANH) - A34-1 (+B) | R - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A32-14 (CANL) - A34-1 (+B) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G62-13 (CANH) - G62-14 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G62-13 (CANH) - A33-8 (GND1) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G62-14 (CANL) - A33-8 (GND1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G62-13 (CANH) - A34-1 (+B) | R - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G62-14 (CANL) - A34-1 (+B) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
TRANSMISSION CONTROL ECU (for CVT)
Refer to Terminals of ECU.
for K120: Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>TERMINALS OF ECU
for K120F: Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Transmission Control ECU) |
Disconnect the transmission control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| C33-15 (CANH) - C33-16 (CANL) | GR - P | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| C33-15 (CANH) - C33-2 (E1) | GR - B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| C33-16 (CANL) - C33-2 (E1) | P - B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| C33-15 (CANH) - C33-1 (+B) | GR - L | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| C33-16 (CANL) - C33-1 (+B) | P - L | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the brake actuator assembly (skid control ECU) connector.
| *a | Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU]) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A39-5 (CANH) - A39-19 (CANL) | P - V | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A39-5 (CANH) - A39-46 (GND1) | P - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A39-19 (CANL) - A39-46 (GND1) | V - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A39-5 (CANH) - A39-1 (+BM) | P - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A39-19 (CANL) - A39-1 (+BM) | V - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
RACK AND PINION POWER STEERING GEAR ASSEMBLY
Refer to Terminals of ECU.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Rack and Pinion Power Steering Gear Assembly) |
| *b | Front view of DLC3 |
Disconnect the rack and pinion power steering gear assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
|
*1: for A25A-FKS and 4WD/AWD *2: except A25A-FKS and 4WD/AWD |
||||
| C54-10 (CANH) - C54-11 (CANL) | G - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| C54-10 (CANH) - C54-7 (PGND) | G - W-L*1
G - B*2 |
HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| C54-11 (CANL) - C54-7 (PGND) | W - W-L*1
W - B*2 |
LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| C54-10 (CANH) - G114-16 (BAT) | G - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| C54-11 (CANL) - G114-16 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
STEERING SENSOR
| *a | Component without harness connected
(Steering Sensor) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Steering Sensor) |
Disconnect the steering sensor connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
|
*1: for LHD and Manual Transaxle *2: except LHD and Manual Transaxle |
||||
| G68-3 (CANH) - G68-8 (CANL) | G - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G68-3 (CANH) - G68-6 (ESS) | G - W-B*1
G - LA*2 |
HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G68-8 (CANL) - G68-6 (ESS) | W - W-B*1
W - LA*2 |
LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G68-3 (CANH) - G68-4 (BAT) | G - LA-B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G68-8 (CANL) - G68-4 (BAT) | W - LA-B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
FORWARD RECOGNITION CAMERA (w/ Pre-collision System)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the forward recognition camera connector.
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| P8-5 (CA1P) - P8-11 (CA1N) | L - B | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| P8-5 (CA1P) - P8-10 (GND) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| P8-11 (CA1N) - P8-10 (GND) | B - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| P8-5 (CA1P) - G114-16 (BAT) | L - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| P8-11 (CA1N) - G114-16 (BAT) | B - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-collision System)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT RADAR SENSOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the millimeter wave radar sensor assembly connector.
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| B9-3 (CA2H) - B9-2 (CA2L) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| B9-3 (CA2H) - B9-1 (SGND) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B9-2 (CA2L) - B9-1 (SGND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B9-3 (CA2H) - G114-16 (BAT) | R - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B9-2 (CA2L) - G114-16 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
AIRBAG SENSOR ASSEMBLY
Refer to Terminals of ECU.
w/ Occupant Classification System: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)>TERMINALS OF ECU
w/o Occupant Classification System: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the airbag sensor assembly connector.
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G70-26 (CANH) - G70-27 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| G70-26 (CANH) - G70-33 (E1) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G70-27 (CANL) - G70-33 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G70-26 (CANH) - G114-16 (BAT) | R - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G70-27 (CANL) - G114-16 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
COMBINATION METER ASSEMBLY
Refer to Terminals of ECU.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G18-9 (CANH) - G18-25 (CANL) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| G18-9 (CANH) - G18-23 (ES) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G18-25 (CANL) - G18-23 (ES) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G18-9 (CANH) - G18-22 (B) | B - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G18-25 (CANL) - G18-22 (B) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
Refer to Terminals of ECU.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU]) |
| *b | Front view of DLC3 |
Disconnect the main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G44-5 (CANH) - G44-4 (CANL) | BE - V | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G44-5 (CANH) - G114-4 (CG) | BE - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G44-4 (CANL) - G114-4 (CG) | V - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G44-5 (CANH) - G114-16 (BAT) | BE - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G44-4 (CANL) - G114-16 (BAT) | V - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the radio and display receiver assembly connectors.
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G2-13 (CANH) - G2-14 (CANL) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G2-13 (CANH) - G3-1 (GND1) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G2-14 (CANL) - G3-1 (GND1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G2-13 (CANH) - G114-16 (BAT) | B - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G2-14 (CANL) - G114-16 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
TELEPHONE TRANSCEIVER ASSEMBLY (w/ Telematics System for ERA-GLONASS)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Telephone Transceiver Assembly) |
Disconnect the telephone transceiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| H6-15 (CANP) - H6-16 (CANN) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| H6-15 (CANP) - H6-4 (E) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H6-16 (CANN) - H6-4 (E) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H6-15 (CANP) - H6-1 (+B) | R - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H6-16 (CANN) - H6-1 (+B) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
TELEPHONE TRANSCEIVER ASSEMBLY (w/ Telematics System for eCall)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Telephone Transceiver Assembly) |
Disconnect the telephone transceiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| H10-25 (CANP) - H10-26 (CANN) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| H10-25 (CANP) - H10-20 (E) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H10-26 (CANN) - H10-20 (E) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H10-25 (CANP) - H10-1 (+B) | R - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H10-26 (CANN) - H10-1 (+B) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
AIR CONDITIONING AMPLIFIER ASSEMBLY
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Disconnect the air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G46-2 (CANH) - G46-1 (CANL) | SB - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G46-2 (CANH) - G46-17 (GND) | SB - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G46-1 (CANL) - G46-17 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G46-2 (CANH) - G46-5 (B) | SB - G | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G46-1 (CANL) - G46-5 (B) | W - G | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System, w/ Parking Assist Monitor System)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the television camera assembly connector.
| *a | Front view of wire harness connector
(to Television Camera Assembly) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| R15-4 (CANH) - R15-1 (CANL) | R - L | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| R15-4 (CANH) - G114-4 (CG) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| R15-1 (CANL) - G114-4 (CG) | L - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| R15-4 (CANH) - G114-16 (BAT) | R - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| R15-1 (CANL) - G114-16 (BAT) | L - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)
Refer to Terminals of ECU.
w/ Parking Support Brake System: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM (for Gasoline Model with Parking Support Brake System)>TERMINALS OF ECU
w/o Parking Support Brake System: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/o Parking Support Brake System)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the clearance warning ECU assembly connector.
| *A | for LHD and Manual Transaxle | *B | except LHD and Manual Transaxle |
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G25-17 (R1) - G25-18 (R2) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G25-17 (R1) - G114-4 (CG) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G25-18 (R2) - G114-4 (CG) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G25-17 (R1) - G114-16 (BAT) | L - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G25-18 (R2) - G114-16 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| H4-17 (R1) - H4-18 (R2) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| H4-17 (R1) - G114-4 (CG) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H4-18 (R2) - G114-4 (CG) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H4-17 (R1) - G114-16 (BAT) | L - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H4-18 (R2) - G114-16 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the blind spot monitor sensor LH connector.
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| Q1-2 (CA1P) - Q1-7 (CA1N) | G - SB | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Q1-2 (CA1P) - Q1-10 (BLGD) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Q1-7 (CA1N) - Q1-10 (BLGD) | SB - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Q1-2 (CA1P) - G114-16 (BAT) | G - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Q1-7 (CA1N) - G114-16 (BAT) | SB - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly]) |
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G54-1 (CANH) - G54-2 (CANL) | G - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G54-1 (CANH) - G54-18 (E) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G54-2 (CANL) - G54-18 (E) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G54-1 (CANH) - G54-4 (+B) | G - P | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G54-2 (CANL) - G54-4 (+B) | W - P | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
HEADLIGHT ECU SUB-ASSEMBLY LH
Refer to Terminals of ECU.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Headlight ECU Sub-assembly LH) |
| *b | Front view of DLC3 |
Disconnect the headlight ECU sub-assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A11-24 (CANH) - A11-23 (CANL) | P - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A11-24 (CANH) - A11-12 (GND) | P - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A11-23 (CANL) - A11-12 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A11-24 (CANH) - G114-16 (BAT) | P - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A11-23 (CANL) - G114-16 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
HEADLIGHT ECU SUB-ASSEMBLY RH
Refer to Terminals of ECU.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Headlight ECU Sub-assembly RH) |
| *b | Front view of DLC3 |
Disconnect the headlight ECU sub-assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A12-24 (CANH) - A12-23 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A12-24 (CANH) - A12-12 (GND) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A12-23 (CANL) - A12-12 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A12-24 (CANH) - G114-16 (BAT) | L - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A12-23 (CANL) - G114-16 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
POSITION CONTROL ECU ASSEMBLY (w/ Memory)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
| *A | for LHD |
| *B | for RHD |
| *a | Front view of wire harness connector
(to Position Control ECU Assembly) |
Disconnect the position control ECU assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| T8-13 (CANP) - T8-14 (CANN) | LG - R | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| T8-13 (CANP) - T7-2 (GND) | LG - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| T8-14 (CANN) - T7-2 (GND) | R - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| T8-13 (CANP) - T7-3 (+B) | LG - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| T8-14 (CANN) - T7-3 (+B) | R - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| S8-13 (CANP) - S8-14 (CANN) | LG - R | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| S8-13 (CANP) - S7-2 (GND) | LG - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| S8-14 (CANN) - S7-2 (GND) | R - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| S8-13 (CANP) - S7-3 (+B) | LG - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| S8-14 (CANN) - S7-3 (+B) | R - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
BUS BUFFER ECU (w/ Bus Buffer ECU)
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Bus Buffer ECU) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G80-2 (CAN+) - G80-1 (CAN-) | LG - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G80-2 (CAN+) - G114-4 (CG) | LG - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G80-1 (CAN-) - G114-4 (CG) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G80-2 (CAN+) - G114-16 (BAT) | LG - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G80-1 (CAN-) - G114-16 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
4WD ECU ASSEMBLY (for 4WD/AWD with Dynamic Torque Control 4WD/AWD System)
Refer to Terminals of ECU.
Click hereDrivetrain>GF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the 4WD ECU assembly connectors.
| *a | Front view of wire harness connector
(to 4WD ECU Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| N4-17 (CANH) - N4-26 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| N4-17 (CANH) - N3-1 (GND) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N4-26 (CANL) - N3-1 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N4-17 (CANH) - N3-2 (BSLC) | L - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| N4-26 (CANL) - N3-2 (BSLC) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
4WD ECU ASSEMBLY (for 4WD/AWD with Dynamic Torque Vectoring AWD System)
Refer to Terminals of ECU.
Click hereDrivetrain>GF2A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE VECTORING AWD SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the 4WD ECU assembly connector.
| *a | Front view of wire harness connector
(to 4WD ECU Assembly) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| N5-6 (CANH) - N5-5 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| N5-6 (CANH) - N5-4 (GND) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N5-5 (CANL) - N5-4 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N5-6 (CANH) - G114-16 (BAT) | L - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| N5-5 (CANL) - G114-16 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
OCCUPANT DETECTION ECU (w/ Occupant Classification System)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Occupant Detection ECU) |
| *b | Front view of DLC3 |
Disconnect the occupant detection ECU connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| S21-5 - S21-4 | R - SB | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| S21-5 - S21-10 | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| S21-4 - S21-10 | SB - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| S21-5 - G114-16 (BAT) | R - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| S21-4 - G114-16 (BAT) | SB - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
SWING GRILLE ACTUATOR ASSEMBLY (w/ Grille Shutter System)
Refer to Terminals of ECU.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER SYSTEM (for Gasoline Model)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Swing Grille Actuator Assembly) |
Disconnect the swing grille actuator assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A85-6 (CANP) - A85-5 (CANN) | G - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A85-6 (CANP) - A85-3 (GND) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A85-5 (CANN) - A85-3 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A85-6 (CANP) - A85-1 (+B) | G - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A85-5 (CANN) - A85-1 (+B) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
MULTIPLEX NETWORK DOOR ECU (w/ Power Back Door System)
Refer to Terminals of ECU.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Multiplex Network Door ECU) |
Disconnect the multiplex network door ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| R18-39 (CANP) - R18-40 (CANN) | L - R | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| R18-39 (CANP) - R19-10 (GND) | L - W | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| R18-40 (CANN) - R19-10 (GND) | R - W | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| R18-39 (CANP) - R19-1 (B) | L - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| R18-40 (CANN) - R19-1 (B) | R - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
PARKING ASSIST ECU (w/ Panoramic View Monitor System)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Parking Assist ECU) |
Disconnect the parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| N25-11 (CANH) - N25-12 (CANL) | GR - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| N25-11 (CANH) - N25-4 (GND1) | GR - LA | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N25-12 (CANL) - N25-4 (GND1) | W - LA | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N25-11 (CANH) - N25-1 (+B) | GR - L | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| N25-12 (CANL) - N25-1 (+B) | W - L | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |