Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)

AUDIO AND VISUAL SYSTEM (for Radio and Display Type) > PROBLEM SYMPTOMS TABLE

for Preparation Click here


HINT:
  1. Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
  2. Inspect the fuses and relays related to this system before inspecting the suspected areas below.


Display Function 
Symptom
Suspected Area
See page
Pressing power switch does not turn on system.
Proceed to "Radio Receiver Power Source Circuit"
Click here
Proceed to "Pressing power switch does not turn on system"
Click here
Radio and display receiver assembly
Click here
Black screen (No image appears on audio screen).
Proceed to "Black Screen"
Click here
Radio and display receiver assembly
Click here
Display does not dim (does not change to night screen) with tail switch on.
Proceed to "Display does not Dim when Light Control Switch is Turned ON"
Click here
Proceed to "Illumination Circuit"
Click here
Radio and display receiver assembly
Click here
Combination meter assembly
Click here
Power does not turn off (Screen remains on).
Proceed to "Radio Receiver Power Source Circuit"
Click here
Radio and display receiver assembly
Click here
Screen is distorted.
Proceed to "Radio Receiver Power Source Circuit"
Click here
Radio and display receiver assembly
Click here
Screen flicker or color distortion.
Proceed to "Screen Flicker or Color Distortion"
Click here
Proceed to "Radio Receiver Power Source Circuit"
Click here
Radio and display receiver assembly
Click here
Audio function switches can be operated while vehicle being driven.
Proceed to "Parking Brake Switch Circuit"
Click here
Radio and display receiver assembly
Click here

Panel Switch and Touch Switch Function 
Symptom
Suspected Area
See page
Illumination for panel switches does not come on with tail switch on.
Proceed to "Illumination for Panel Switch does not Come on with Tail Switch ON"
Click here
Proceed to "Illumination Circuit"
Click here
Radio and display receiver assembly
Click here
Combination meter assembly
Click here
Panel switches do not function.
Proceed to "Panel Switches do not Function"
Click here
Proceed to "Radio Receiver Power Source Circuit"
Click here
Radio and display receiver assembly
Click here
Touch panel switch does not function.
Proceed to "Touch Panel Switch does not Function"
Click here
Proceed to "Radio Receiver Power Source Circuit"
Click here
Radio and display receiver assembly
Click here
Audio function switches can be operated while vehicle is driving.
Proceed to "Parking Brake Switch Circuit"
Click here
Radio and display receiver assembly
Click here

Steering Pad Switch Function 
Symptom
Suspected Area
See page
System cannot be operated by steering pad switch.
Proceed to "Panel Switches do not Function"
Click here
Proceed to "Steering Pad Switch Circuit"
Click here
Radio and display receiver assembly
Click here
Illumination for steering pad switch does not come on with tail switch on.
Proceed to "Illumination Circuit"
Click here
Radio and display receiver assembly
Click here
Combination meter assembly
Click here

General Audio Function 
Symptom
Suspected Area
See page
No sound can be heard from speakers.
Proceed to "No Sound can be Heard from Speakers"
Click here
Proceed to "Speaker Circuit"
Click here
Radio and display receiver assembly
Click here
Abnormal noise occurs.
Proceed to "Noise Occurs"
Click here
Radio and display receiver assembly
Click here
Sound quality is bad in all modes. (Volume is too low).
Check that the ASL function is off.
-
Proceed to "Poor Sound Quality in All Modes (Low Volume)"
Click here
Proceed to "Speaker Circuit"
Click here
Radio and display receiver assembly
Click here
ASL does not function.
Check that the ASL function is on.
-
Proceed to "Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter"
Click here
Radio and display receiver assembly
Click here

FM or AM Radio Function 
Symptom
Suspected Area
See page
Radio broadcast cannot be received or poor reception.
Proceed to "Radio Broadcast cannot be Received (Bad Reception)"
Click here
Radio broadcast can be received but radio station cannot be displayed (Some radio stations do not provide their name information).
Radio and display receiver assembly
Click here
Radio broadcast can be displayed but radio broadcast cannot be heard from speakers.
Check the volume settings
-
Radio and display receiver assembly
Click here
Radio broadcast can be received but station list cannot be displayed.
Wait for 120 seconds in radio mode, and select the "Refresh" switch on the station list screen
-
Radio and display receiver assembly
Click here
Radio broadcast can be received but station list cannot be displayed.
Select the "Refresh" switch on the station list screen
-
Wait for 10 minutes with the ignition switch turned to ACC, and select the "Refresh" switch on the station list screen again
-
Radio and display receiver assembly
Click here
After the voice recognition function or hands-free function is turned off, the cache radio does not operate.
Check that the cache radio setting is on
-
Radio and display receiver assembly
Click here

Disc Player Function 
Symptom
Suspected Area
See page
Disc cannot be played or player does not function with disc.
Proceed to "Disc Player Outline" in System Description and check if the disc is compatible with the disc player
Click here
Radio and display receiver assembly
Click here
Disc cannot be inserted/played or disc is ejected right after insertion.
Proceed to "Disc cannot be Inserted or is Ejected Right After Insertion"
Click here
Disc cannot be ejected.
Proceed to "Disc cannot be Ejected"
Click here
CD/DVD sound skips.
Proceed to "CD/DVD Sound Skips"
Click here
While vehicle is stopped, disc cannot be viewed even when parking brake is set (parking brake switch is on).
Proceed to "Parking Brake Switch Circuit"
Click here
Radio and display receiver assembly
Click here
Screen color is poor only when watching a disc.
Change the color settings on the screen adjustment screen
-
Radio and display receiver assembly
Click here
Sound quality is bad only when disc is played (volume is too low).
Proceed to "Sound Quality is Bad Only when Disc is Played (Volume is Too Low)"
Click here
When CD is playing, some cover art is not displayed.
When a song unregistered to the Gracenote CDDB is playing, its cover art cannot be displayed
-
When CD is playing, cover art cannot be displayed.
Radio and display receiver assembly
Click here
Album cover art cannot be displayed.
Check that Display Cover Art on the disc settings screen is set to on
-
Check if similar symptoms occur with another vehicle
-
Radio and display receiver assembly
Click here

AUX (Stereo Jack) Function 
Symptom
Suspected Area
See page
External device sound cannot be heard or sound quality is bad (Stereo jack is used).
Proceed to "Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter"
Click here
No. 1 stereo jack adapter assembly
Click here
Radio and display receiver assembly
Click here
"AUX/USB" is not displayed on system check mode screen.
Proceed to "Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter"
Click here
No. 1 stereo jack adapter assembly
Click here
Radio and display receiver assembly
Click here

"Bluetooth" Hands-free Function 
Symptom
Suspected Area
See page
"Bluetooth" is inoperative (In-vehicle device cannot be recognized by the cellular phone).
Proceed to "Cellular Phone Inspection"
Click here
Radio and display receiver assembly
Click here
"Bluetooth" compatible cellular phone cannot be registered.
Proceed to "Cellular Phone Registration Failure"
Click here
"Bluetooth" compatible cellular phone cannot be connected.
Check that no other cellular phone is connected as a hands-free device
-
Bring the cellular phone near the in-vehicle device and reconnect it
-
Proceed to "Cellular Phone Inspection"
Click here
Radio and display receiver assembly
Click here
"Bluetooth" compatible cellular phone cannot be connected automatically (can be connected manually).
Check that "Bluetooth" automatic connection setting of the in-vehicle device is on
-
Radio and display receiver assembly
Click here
"Bluetooth" compatible cellular phone connection is disconnected.
Bring the cellular phone near the in-vehicle device and check if it is reconnected
-
Proceed to "Cellular Phone Inspection"
Click here
Radio and display receiver assembly
Click here
Message that prompts to check the cellular phone is displayed.
Bring the cellular phone near the in-vehicle device and check if it is reconnected
-
Proceed to "Cellular Phone Inspection"
Click here
Radio and display receiver assembly
Click here
When the ignition switch is turned to ACC, instructions for checking the connection condition between the in-vehicle device and cellular phone are displayed.
Turn the cellular phone connection conformation display on the in-vehicle device off
-
Phonebook data cannot be transferred.
Check that the phonebook automatic transfer setting of the in-vehicle device is on
-
Enter "1234" into the "Bluetooth" phone (when transferring phonebook data, OBEX authentication may be required)
-
Check that no applications on the cellular phone are running
-
If using "Bluetooth" audio function, cancel the "Bluetooth" audio player connection and check the operation
-
Transfer phonebook data manually
-
Proceed to "Cellular Phone Inspection"
Click here
Radio and display receiver assembly
Click here
Phonebook data is cleared.
Radio and display receiver assembly
Click here
Phonebook data cannot be edited.
Check that the phonebook data automatic transfer setting is off
-
Radio and display receiver assembly
Click here
All the transferred phonebook data is sorted to "Other".
Check that no applications on the cellular phone are operating
-
Check that phonebook data in the cellular phone is not stored to the SIM card
-
Proceed to "Cellular Phone Inspection"
Click here
Explain to the customer that all the transferred phonebook data may be stored to "Other" depending on cellular phone
-
Cellular phone cannot make outgoing/ incoming calls.
Move the vehicle into a cellular phone service area, check that the "Bluetooth" device is connected to the vehicle and operate device again
-
Check that the cellular phone can make outgoing/incoming calls properly when not connected via "Bluetooth"
-
Proceed to "Cellular Phone Inspection"
Click here
Radio and display receiver assembly
Click here
Other caller's voice is interrupted by noise or sound quality is poor.
Check the receiving voice volume (if it is too high, voice may sound distorted)
-
Make a call with the cellular phone disconnected from "Bluetooth" and check that other caller's voice can be heard clearly
-
Proceed to "Check Hands-free Voice Quality Setting" in Operation Check
Click here
Proceed to "Cellular Phone Inspection"
Click here
Radio and display receiver assembly
Click here
Other caller's voice cannot be heard.
Check that reception voice volume is not set to minimum
-
Make a call with the cellular phone disconnected from "Bluetooth" and check that other caller's voice can be heard clearly
-
Proceed to "Check Hands-free Voice Quality Setting" in Operation Check
Click here
Proceed to "Cellular Phone Inspection"
Click here
Radio and display receiver assembly
Click here
Caller's voice (your voice) is interrupted by noise or sound quality is poor.
Check the transmitting voice volume (if it is too high, voice may sound distorted)
-
Check that nothing can cause noise around the microphone (an outlet of the air conditioning system facing the microphone, wind from an open window, additional devices, etc. may affect noise occurrence)
-
Proceed to "Check Hands-free Voice Quality Setting" in Operation Check
Click here
Proceed to "Cellular Phone Inspection"
Click here
Proceed to "Microphone Circuit between Microphone and Radio Receiver"
Click here
Other caller cannot hear your voice.
When talking on the cellular phone, check that the mute button is not pressed
-
Check that nothing can cause noise around the microphone (an outlet of the air conditioning system facing the microphone, wind from an open window, additional devices, etc. may affect noise occurrence)
-
Proceed to "Check Hands-free Voice Quality Setting" in Operation Check
Click here
Proceed to "Cellular Phone Inspection"
Click here
Proceed to "Microphone Circuit between Microphone and Radio Receiver"
Click here
No notification when a new SMS/MMS/e-mail has been received
Check the SMS/MMS/e-mail notification settings on the cellular phone and the Radio and display receiver assembly
-
Proceed to "Cellular Phone Inspection"
Click here
Radio and display receiver assembly
Click here

"Bluetooth" Audio Function 
Symptom
Suspected Area
See page
Portable player cannot be registered.
Proceed to "Portable Player cannot be Registered"
Click here
Radio and display receiver assembly
Click here
Portable player cannot be connected manually/automatically.
Proceed to "Portable Player cannot be Registered"
Click here
Proceed to "Portable Player cannot be Connected Manually/Automatically"
Click here
Radio and display receiver assembly
Click here
Cellular phone with portable audio function cannot be recognized as "Bluetooth" audio device even when connected using "Bluetooth".
Proceed to "Portable Player cannot be Registered"
Click here
Proceed to "Portable Player cannot be Connected Manually/Automatically"
Click here
Radio and display receiver assembly
Click here
Sound of portable player cannot be heard from speakers, or sound is low.
Proceed to "Sound of Portable Player cannot be Heard from Speakers or Sound is Low"
Click here
Radio and display receiver assembly
Click here
Portable player does not play even after "Bluetooth" audio mode is selected.
Proceed to "Does not Play even after Bluetooth Audio Mode is Selected"
Click here
Radio and display receiver assembly
Click here
Portable player does not play.
Proceed to "Does not Play even after Bluetooth Audio Mode is Selected"
Click here
Radio and display receiver assembly
Click here
Track information such as track number, track name, elapsed play time and playlist is not displayed.
Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device"
Click here
Radio and display receiver assembly
Click here
Operation switches for portable player such as play, pause, repeat, random and scan are not displayed.
Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device"
Click here
Radio and display receiver assembly
Click here
Battery condition of portable player is not displayed.
Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device"
Click here
Radio and display receiver assembly
Click here
"Bluetooth" signal condition is not displayed.
Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device"
Click here
Radio and display receiver assembly
Click here
Portable player cannot pause, select file, fast forward, fast rewind, play at random or scan.
Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device"
Click here
Radio and display receiver assembly
Click here
Noise occurs or sound skips when portable player plays.
Proceed to "Noise Occurs or Sound Skips when Portable Player Plays"
Click here
Radio and display receiver assembly
Click here
Registered device cannot be deleted.
Proceed to "Registered Device cannot be Deleted"
Click here
Radio and display receiver assembly
Click here

USB Audio System Function 
Symptom
Suspected Area
See page
USB audio system sound cannot be heard or sound quality is bad (USB connector is used).
Proceed to "Data Signal Circuit between Radio Receiver and Stereo Jack Adapter"
Click here
No. 1 stereo jack adapter assembly
Click here
Radio and display receiver assembly
Click here
USB device or "iPod" is not recognized.
Proceed to "USB Audio System Recognition/Play Error"
Click here
No. 1 stereo jack adapter assembly
Click here
Radio and display receiver assembly
Click here
Track information such as track, artist and album names is not displayed.
Proceed to "USB Audio System Recognition/Play Error"
Click here
No. 1 stereo jack adapter assembly
Click here
Radio and display receiver assembly
Click here
USB device or "iPod" is recognized but cannot play, or can play but not in a sorted order.
Proceed to "USB Audio System Recognition/Play Error"
Click here
No. 1 stereo jack adapter assembly
Click here
Radio and display receiver assembly
Click here
Album cover art cannot be displayed.
Check that Display Cover Art on the "iPod" or USB Settings screen is set to
-
Check if similar symptoms occur with another vehicle
-
Radio and display receiver assembly
Click here
User set album cover art cannot be displayed.
Check if the priority display of Gracenote database album cover art setting is off
-
Check that a JPEG file is used for the album cover art registered to the music data in the USB device or "iPod" - Radio and display receiver assembly
-
Radio and display receiver assembly
Click here
"iPod" battery cannot be charged.
Proceed to "USB Audio System Recognition/Play Error"
Click here
No. 1 stereo jack adapter assembly
Click here
Radio and display receiver assembly
Click here

Customize Startup Image or Screen Off Image Function 
Symptom
Suspected Area
See page
Screen cannot be changed to UIC setting screen.
Radio and display receiver assembly
Click here
Thumbnails for opening image setting or screen off image setting do not update when USB device is connected.
Check that the USB device was not disconnected while transferring an image
-
Check that the screen was not changed to another function menu while transferring an image
-
Proceed to "USB Audio System Recognition/ Play Error"
Click here
No. 1 stereo jack adapter assembly
Click here
Radio and display receiver assembly
Click here
Transfer button cannot be pressed.
Check that a USB device is connected
-
Check that the USB device is not in use (USB audio system is playing etc.)
-
Proceed to "USB Audio System Recognition/ Play Error"
Click here
No. 1 stereo jack adapter assembly
Click here
Radio and display receiver assembly
Click here
Image data in USB device cannot be displayed.
Check that the designated folder name is used
-
Check that the file extension of the data is JPG or JPEG
-
Check that the file name is 32 characters or less and available language is used
-
Check that the image data size is 10 MB or less
-
Check that the file system of the USB device is FAT16 or FAT32
-
Proceed to "USB Audio System Recognition/ Play Error"
Click here
No. 1 stereo jack adapter assembly
Click here
Radio and display receiver assembly
Click here
Set opening image or screen off image is not displayed.
Check if it is the first start-up after disconnecting and reconnecting the +B terminal (reading from the SD card may be slow when the system is first starting-up)
-
Set the opening image or screen off image again
-
Radio and display receiver assembly
Click here
Stored image cannot be deleted.
Radio and display receiver assembly
Click here
Message indicating that USB device cannot be accessed is displayed.
Check that the USB device has not been disconnected while the audio and visual system is recognizing it
-
Proceed to "USB Audio System Recognition/ Play Error"
Click here
No. 1 stereo jack adapter assembly
Click here
Radio and display receiver assembly
Click here
Thumbnail images for opening image or screen off image are not displayed on setting screen.
Check if it is the first start-up after disconnecting and reconnecting the +B terminal (reading from the SD card may be slow when the system is first starting-up)
-
Set the opening image or screen off image again
-
Radio and display receiver assembly
Click here
Image cannot be set for opening image or screen off image on setting screen.
Set the opening image or screen off image again
-
Radio and display receiver assembly
Click here

"MirrorLink" Function (w/ "MirrorLink" Function) 
Symptom
Suspected Area
See page
Although USB device or "iPod" is recognized, "MirrorLink" function cannot be started (smartphone battery can be charged).
Proceed to "MirrorLink Function cannot be Started"
Click here
Image is not displayed.
Proceed to "MirrorLink Image is not Displayed"
Click here
Sound cannot be heard.
Proceed to "MirrorLink Sound cannot be Heard"
Click here
"MirrorLink" is inoperative only when smartphone is connected to head unit.
Proceed to "MirrorLink is Inoperative"
Click here